Oracle10g安装以前检查先决条件"Microsoft LoopBack Adapter配置为系统的主网络适配器"的问题解决

Oracle10g安装以前检查先决条件"Microsoft LoopBack Adapter配置为系统的主网络适配器"的问题解决
问题解决   2009-09-26 15:32   阅读229   评论0 
字号： 大大  中中  小小

很早以前就装过，好像也遇到过类似问题，当时没管他，直接点下一步了，这次得认真点了，不然以后因为安装的问题惹麻烦就不值得了。

安装时，提示

正在检查网络配置需求... 检查完成。此次检查的总体结果为: 未执行 <<<<
建议案: Oracle 支持在具有 DHCP 分配的 IP 地址的系统上进行安装。但在安装之前, 必须将 Microsoft LoopBack Adapter 配置为系统的主网络适配器。有关在配置有 DHCP 的系统上安装软件的详细信息, 请参阅 Installation Guide。

原因，我的机器IP是自动获取的，即IP是路由器使用DHCP动态分配的。

下面找到的解决方案

安装oracle10g前，控制面板－添加硬件－选“是，我已经连接了此设备”点击下一步－在列表中选择添加新的硬件设备－选“安装我充从手动。。。”－接下来的列表中选择 “Microsoft loopback adapter ” 并将此网络连接设置为固定IP如 192.168.0.xxx，完事儿了再安装oracle 10g。

这时出现一个假的本地连接，不停的在获取IP，其实没用，只是能让racle通过检验（具体为什么我也在找，可是没有满意回答的话贴出来），设置一个固定的ip，哈哈，去监测吧，保证通过！！

下面英文的是微软官方的XP下安装Microsoft Loopback adapter的文档，请大家参阅。

     引自：http://support.microsoft.com/default.aspx?scid=kb;en-us;839013
*\

How to install the Microsoft Loopback adapter in Windows XP

SUMMARY
The Microsoft Loopback adapter is a testing tool for a virtual network environment where network access is not available. Also, you must use the Loopback adapter if there are conflicts with a network adapter or with a network adapter driver. You can bind network clients, protocols, and other network configuration items to the Loopback adapter, and you can install the network adapter driver or network adapter later while retaining the network configuration information. You can also install the Loopback adapter during the unattended installation process.


Back to the top

Manual installation
To manually install the Microsoft Loopback adapter in Windows XP, follow these steps: 1. Click Start, and then click Control Panel.
2. If you are in Classic view, click Switch to Category View under Control Panel in the left pane.
3. Double-click Printers and Other Hardware, and then click Next.
4. Under See Also in the left pane, click Add Hardware,and then click Next.
5. Click Yes, I have already connected the hardware, and then click Next.
6. At the bottom of the list, click Add a new hardware device, and then click Next.
7. Click Install the hardware that I manually select from a list, and then click Next.
8. Click Network adapters, and then click Next.
9. In the Manufacturer box, click Microsoft.
10. In the Network Adapter box, click Microsoft Loopback Adapter, and then click Next.
11. Click Finish.
After the adapter is installed successfully, you can manually configure its options, as with any other adapter. If the TCP/IP properties are configured to use DHCP, the adapter will eventually use an autonet address (169.254.x.x/16) because the adapter is not actually connected to any physical media.

Note By default, TCP/IP properties are configured to use DHCP.

/**
   附上无人值守安装的方法，有兴趣玩玩，我没测试啊~
*/

Unattended installation
To install the Microsoft Loopback adapter, use the following sample Unattend.txt file as a model for your Unattend.txt file: [NetAdapters]
Adapter01=Params.Adapter01

[Params.Adapter01]
InfID="*msloop"
; Microsoft Loopback Adapter
ConnectionName ="MS Loopback Adapter"

[NetProtocols]
MS_TCPIP=Params.MS_TCPIP
; TCP/IP parameters
; Use parameter values specific to your network

[Params.MS_TCPIP]
AdapterSections=params.TCPIP.Adapter01
DNS=yes
DNSSuffixSearchOrder=mycorp.com
EnableLMHosts=No
; Adapter Specific TCP/IP parameters
; Use parameter values specific to your network

[params.TCPIP.Adapter01]
SpecificTo=Adapter01
DNSDomain=mycorp.com
DNSServerSearchOrder=192.168.5.251
WINS=no
DHCP=no
IPAddress=192.168.5.10
SubnetMask=255.255.255.0
DefaultGateway=192.168.5.254