华为vrrp配置

华为vrrp配置

自己的思路：

1：先规划网段
2：将所有层次的设备进行配置
3：将规划好的网段的IP给对应的设备进行配置
4：做我们的服务（vrrp），然后配置路由表（这里我用的静态路由）
5:验证所有网段是否能ping通，采用tracert命令来检查vrrp是否配置成功？

第二步
Sw3:
system-view
[Huawei]vlan 10
[Huawei-vlan10]
[Huawei-vlan10]vlan 20
[Huawei-vlan20]qu
[Huawei]interface e0/0/1
[Huawei-Ethernet0/0/1]port link-type access
[Huawei-Ethernet0/0/1]port default vlan 10
[Huawei-Ethernet0/0/1]qu
[Huawei]in e0/0/2
[Huawei-Ethernet0/0/2]port link-type access
[Huawei-Ethernet0/0/2]port default vlan 20
[Huawei-Ethernet0/0/2]qu
[Huawei]interface e0/0/3
[Huawei-Ethernet0/0/3]port link-type trunk
[Huawei-Ethernet0/0/3]port trunk allow-pass vlan all
[Huawei-Ethernet0/0/3]qu
[Huawei]in e0/0/4
[Huawei-Ethernet0/0/4]port link-type trunk
[Huawei-Ethernet0/0/4]port trunk allow-pass vlan all
[Huawei-Ethernet0/0/4]quit

Sw1:
Sys
Vlan 10
Vlan 20
Qu
In g0/0/1
Port link-type trun
Port trunk allow-pass vlan all
Qu
Vlan 30
Qu
In vlanif 30
Ip address 192.168.30.2 255.255.255.0
Quit
In g0/0/2
Port link-type access
Port default vlan 30
Quit
In vlanif 10
Ip add 192.168.10.1 255.255.255.0
Qu
In vlanif 20
Ip add 192.168.20.1 255.255.255.0
Qu

Sw2:
Sys
Vlan 10
Vlan 20
Qu
In g0/0/1
Port link-type trun
Port trunk allow-pass vlan all
Qu
Vlan 40
Qu
In vlanif 40
Ip address 192.168.40.2 255.255.255.0
Quit
In g0/0/2
Port link-type access
Port default vlan 40
Quit
In vlanif 10
Ip add 192.168.10.2 255.255.255.0
Qu
In vlanif 20
Ip add 192.168.20.2 255.255.255.0
Qu

第三步
R1:
SYS
IN G0/0/0
IP ADD 192.168.50.1 255.255.255.0
Undo shutdown
Quit
In e0/0/0
Ip add 192.168.30.1 255.255.255.0
Undo shutdown
Quit
In e0/0/1
Ip add 192.168.40.1 255.255.255.0
Undo shutdown
Quit

第四步
Sw1：
[Huawei]in vlanif 10
[Huawei-Vlanif10]vrrp vrid 1 virtual-ip 192.168.10.254
[Huawei-Vlanif10]vrrp vrid 1 priority 200
[Huawei-Vlanif10]vrrp vrid 1 preempt-mode timer delay 0
[Huawei-Vlanif10]quit
[Huawei]in vlanif 20
[Huawei-Vlanif20]vrrp vrid 2 virtual-ip 192.168.20.254
[Huawei-Vlanif20]quit
Sw2:
in vlanif 10
vrrp vrid 1 virtual-ip 192.168.10.254
quit
in vlanif 20
vrrp vrid 2 virtual-ip 192.168.20.254
vrrp vrid 2 priority 200
vrrp vrid 2 preempt-mode timer delay 0
quit

静态路由：
display ip routing-table （查看路由表）
R1：
ip route-static 192.168.10.0 255.255.255.0 192.168.30.2
ip route-static 192.168.10.0 255.255.255.0 192.168.40.2
ip route-static 192.168.20.0 255.255.255.0 192.168.30.2
ip route-static 192.168.20.0 255.255.255.0 192.168.40.2
Sw1：
ip route-static 192.168.40.0 255.255.255.0 192.168.30.1
ip route-static 192.168.50.0 255.255.255.0 192.168.30.1
Sw2：
ip route-static 192.168.30.0 255.255.255.0 192.168.40.1
ip route-static 192.168.50.0 255.255.255.0 192.168.40.1
改成动态RIP协议
Swith1
[Huawei]rip 1
[Huawei-rip-1]network 192.168.10.0
[Huawei-rip-1]network 192.168.20.0
[Huawei-rip-1]network 192.168.30.0
Switch2
[Huawei]rip 1
[Huawei-rip-1]network 192.168.40.0
[Huawei-rip-1]network 192.168.10.0
[Huawei-rip-1]network 192.168.20.0
R1
[Huawei]rip 1
[Huawei-rip-1]network 192.168.50.0
[Huawei-rip-1]network 192.168.30.0
[Huawei-rip-1]network 192.168.40.0

第五步:验证所有网段是否能ping通，采用tracert命令来检查vrrp是否配置成功？

以上图片说明vrrp的抢占功能实现