命名性访问控制列表的配置:

创建ACL:
语法:
Router(config)# ip access-list { standard | extended }access-list-name
配置标准命名ACL:
语法:
Router(config-std-nac)# [ Sequence-Number ] { permit | deny }source[ source-wildcard ]

配置扩展命名ACL:

语法:router(config-ext-nacl)# [ Sequence-Number ] { permit | deny } protocol { source source-wildcard destination destionation-wildcard } [operator operan]
标准命名ACL应用实例:
router(config)#ip access-list standard cisco
router(config-std-nacl)# permit host 192.168.1.1
router(config-std-nac)# deny any
//只允许来自主机192.168.1.1/24的流量通过
查看ACL配置信息:
router#show access-list
    Standard IP access list cisco
        10 permit 192.168.1.1
        20 deny any

Demo:

命名性访问控制列表的配置实验_第1张图片

sw:
sw#conf t
sw(config)#vlan 10,20
sw(config-vlan)#ex
sw(config)#do show vlan-sw b
VLAN Name                             Status    Ports
---- -------------------------------- --------- -------------------------------
1    default                          active    Fa1/0, Fa1/1, Fa1/2, Fa1/3
                                                Fa1/4, Fa1/5, Fa1/6, Fa1/7
                                                Fa1/8, Fa1/9, Fa1/10, Fa1/11
                                                Fa1/12, Fa1/13, Fa1/14, Fa1/15
10   VLAN0010                         active    
20   VLAN0020                         active    
1002 fddi-default                     act/unsup 
1003 token-ring-default               act/unsup 
1004 fddinet-default                  act/unsup 
1005 trnet-default                    act/unsup 
sw(config)#int f1/3
sw(config-if)#sw mo acc
sw(config-if)#sw acc vlan 20
sw(config-if)#ex
sw(config)#do show vlan-sw b
VLAN Name                             Status    Ports
---- -------------------------------- --------- -------------------------------
1    default                          active    Fa1/0, Fa1/4, Fa1/5, Fa1/6
                                                Fa1/7, Fa1/8, Fa1/9, Fa1/10
                                                Fa1/11, Fa1/12, Fa1/13, Fa1/14
                                                Fa1/15
10   VLAN0010                         active    Fa1/1, Fa1/2
20   VLAN0020                         active    Fa1/3
1002 fddi-default                     act/unsup 
1003 token-ring-default               act/unsup 
1004 fddinet-default                  act/unsup 
1005 trnet-default                    act/unsup 
sw(config)#int f1/0
sw(config-if)#sw mo t
sw(config-if)#sw t en dot
sw(config-if)#ex
sw(config)#no ip routing        //关闭路由功能
SW3:
sw-3#conf t
sw-3(config)#int f1/1
sw-3(config-if)#no switchport                     
sw-3(config-if)#ip add 192.168.100.1 255.255.255.0
sw-3(config-if)#no shut
sw-3(config-if)#do show ip int b
Interface                  IP-Address      OK? Method Status                Protocol
FastEthernet0/0            unassigned      YES unset  administratively down down    
FastEthernet0/1            unassigned      YES unset  administratively down down    
FastEthernet1/0            unassigned      YES unset  up                    up      
FastEthernet1/1            192.168.100.1   YES manual up                    up      
FastEthernet1/2            unassigned      YES unset  up                    down    
FastEthernet1/3            unassigned      YES unset  up                    down    
FastEthernet1/4            unassigned      YES unset  up                    down    
FastEthernet1/5            unassigned      YES unset  up                    down    
FastEthernet1/6            unassigned      YES unset  up                    down    
FastEthernet1/7            unassigned      YES unset  up                    down    
FastEthernet1/8            unassigned      YES unset  up                    down    
FastEthernet1/9            unassigned      YES unset  up                    down    
FastEthernet1/10           unassigned      YES unset  up                    down    
FastEthernet1/11           unassigned      YES unset  up                    down    
FastEthernet1/12           unassigned      YES unset  up                    down    
FastEthernet1/13           unassigned      YES unset  up                    down    
FastEthernet1/14           unassigned      YES unset  up                    down    
FastEthernet1/15           unassigned      YES unset  up                    down    
Vlan1                      unassigned      YES unset  up                    up      
sw-3(config-if)#ex       
sw-3(config)#vlan 10,20
sw-3(config-vlan)#int vlan 10
sw-3(config-if)#ip add 192.168.10.1 255.255.255.0
sw-3(config-if)#no shut
sw-3(config-if)#ex
sw-3(config)#int vlan 20
sw-3(config-if)#ip add 192.168.20.1 255.255.255.0
sw-3(config-if)#no shut
sw-3(config-if)#ex
sw-3(config)#int f1/0
sw-3(config-if)#sw mo t
sw-3(config-if)#sw t en dot
sw-3(config-if)#do shoe ip route 
Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area 
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2
       i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
       ia - IS-IS inter area, * - candidate default, U - per-user static route
       o - ODR, P - periodic downloaded static route

Gateway of last resort is not set

C    192.168.10.0/24 is directly connected, Vlan10
C    192.168.20.0/24 is directly connected, Vlan20
C    192.168.100.0/24 is directly connected, FastEthernet1/1
//三个网段配置成功
sw-3(config-if)#ex
四台主机配置IP地址:
PC1:
PC1> ip 192.168.100.100 192.168.100.1
Checking for duplicate address...
PC1 : 192.168.100.100 255.255.255.0 gateway 192.168.100.1

PC2:
PC2> ip 192.168.10.10 192.168.10.1
Checking for duplicate address...
PC1 : 192.168.10.10 255.255.255.0 gateway 192.168.10.1

PC3:
PC3> ip 192.168.10.20 192.168.10.1
Checking for duplicate address...
PC1 : 192.168.10.20 255.255.255.0 gateway 192.168.10.1

PC4:
PC4> ip 192.168.20.20 192.168.20.1
Checking for duplicate address...
PC1 : 192.168.20.20 255.255.255.0 gateway 192.168.20.1
此时PC2应该是全网互通的:
验证全网互通:
PC2> ping 192.168.100.100
192.168.100.100 icmp_seq=1 timeout
84 bytes from 192.168.100.100 icmp_seq=2 ttl=63 time=35.971 ms
84 bytes from 192.168.100.100 icmp_seq=3 ttl=63 time=41.517 ms
84 bytes from 192.168.100.100 icmp_seq=4 ttl=63 time=31.738 ms
84 bytes from 192.168.100.100 icmp_seq=5 ttl=63 time=35.188 ms

PC2>ping 192.168.10.20                                  
84 bytes from 192.168.10.20 icmp_seq=1 ttl=64 time=0.505 ms
84 bytes from 192.168.10.20 icmp_seq=2 ttl=64 time=0.000 ms
84 bytes from 192.168.10.20 icmp_seq=3 ttl=64 time=0.000 ms
84 bytes from 192.168.10.20 icmp_seq=4 ttl=64 time=0.000 ms
84 bytes from 192.168.10.20 icmp_seq=5 ttl=64 time=0.000 ms

PC2> ping 192.168.20.20
192.168.20.20 icmp_seq=1 timeout
84 bytes from 192.168.20.20 icmp_seq=2 ttl=63 time=31.229 ms
84 bytes from 192.168.20.20 icmp_seq=3 ttl=63 time=37.597 ms
84 bytes from 192.168.20.20 icmp_seq=4 ttl=63 time=31.007 ms
84 bytes from 192.168.20.20 icmp_seq=5 ttl=63 time=40.123 ms
注入命令访问控制列表规则:
sw-3(config)#ip access-list standard kgc
sw-3(config-std-nacl)#permit host 192.168.10.10
sw-3(config-std-nacl)#deny 192.168.10.0 0.0.0.255
sw-3(config-std-nacl)#permit any
sw-3(config-std-nacl)#ex
sw-3(config)#do show access-list
Standard IP access list kgc
    10 permit 192.168.10.10
    20 deny   192.168.10.0, wildcard bits 0.0.0.255
    30 permit any
sw-3(config)#int f1/1
sw-3(config-if)#ip access-group kgc out     //策略应用在网关

此时联通结果如下:

PC2可以访问:
PC2> ping 192.168.100.100                               
192.168.100.100 icmp_seq=1 timeout
192.168.100.100 icmp_seq=2 timeout
84 bytes from 192.168.100.100 icmp_seq=3 ttl=63 time=35.353 ms
84 bytes from 192.168.100.100 icmp_seq=4 ttl=63 time=31.321 ms
84 bytes from 192.168.100.100 icmp_seq=5 ttl=63 time=31.239 ms
PC4可以访问:
PC4> ping 192.168.100.100
84 bytes from 192.168.100.100 icmp_seq=1 ttl=63 time=32.766 ms
84 bytes from 192.168.100.100 icmp_seq=2 ttl=63 time=31.240 ms
84 bytes from 192.168.100.100 icmp_seq=3 ttl=63 time=31.244 ms
84 bytes from 192.168.100.100 icmp_seq=4 ttl=63 time=31.329 ms
84 bytes from 192.168.100.100 icmp_seq=5 ttl=63 time=31.067 ms
PC3显示被拒绝:
PC3> ping 192.168.100.100
*192.168.10.1 icmp_seq=1 ttl=255 time=30.919 ms (ICMP type:3, code:13, Communication administratively prohibited)
*192.168.10.1 icmp_seq=2 ttl=255 time=16.133 ms (ICMP type:3, code:13, Communication administratively prohibited)
*192.168.10.1 icmp_seq=3 ttl=255 time=31.012 ms (ICMP type:3, code:13, Communication administratively prohibited)
*192.168.10.1 icmp_seq=4 ttl=255 time=22.354 ms (ICMP type:3, code:13, Communication administratively prohibited)
*192.168.10.1 icmp_seq=5 ttl=255 time=15.630 ms (ICMP type:3, code:13, Communication administratively prohibited)