C2. AIDA File Tool-2

Future Value Type（未来值类型）	选中后，通过按下指定OPC DA服务器的“Start”按钮开始采集数据。	R/W	R/W
Past Value（历史值）	选中后，通过指定的OPC HDA服务器收集开始时间到结束时间之间的数据。	R/W	R/W
Period （周期）	数据采集周期。当选中未来值类型时有效。选中“Period（周期）”或“No of samples（样本数）”。	R/W	R/W
No of samples (样本数)	要生成的样本数。它在选择未来值类型时有效。选中“Period（周期）”或“No of samples（样本数）”。	R/W	R/W
Start Time / End Time（开始时间/结束时间）	生成的开始时间和结束时间。数据格式为“MM / DD / YYYY HH：MI：SS”。结束时间的默认值为“Now”。	R/W	R/W
Acquisition Cycle（采集周期）	采集周期指定数据采集周期。单位可在小时/分/秒之间选择。	R/W	R/W
Start（开始）	点击“start（开始）”后，将开始数据采集。同时还将检查和标记非法数据和错误/可疑数据。	R/W	R/W
Terminate （终止）	通过单击“Terminate（终止）”，数据采集将在中途停止。	R/W	R/W
File  Create New Definition File（文件创建新的定义文件）	通过从“File（文件）”下拉菜单中单击“Import Task（导入任务）”，将显示导入任务对话框，如图B3.2.0b所示。它将选中的定义复制到调度程序配置文件夹。	R/W	R/W
File Open Definition File（文件打开定义文件）	通过单击“File（文件）”下拉菜单中的“Append Task（附加任务）”，将出现如图B3.0.0c所示的附加任务对话框。它将所选的控制器附加到调度程序。	R/W	R/W
File  Save Definition File（文件保存定义文件）	通过单击“File（文件）”下拉菜单中的“Remove Task（删除任务）”，将出现如图B3.0.0c所示的删除任务对话框。它将所选的控制器附加到调度程序。	R/W	R/W
File  Save Definition File As…（文件将定义文件另存为...）	通过单击“File（文件）”下拉菜单中的“Export Task（导出任务）”，将出现如图B3.2.0b所示的导出对话框。它将选中的定义复制到调度程序配置文件夹。	R/W	R/W
File  Open Data File（文件打开数据文件）	通过单击“Edit（编辑）”下拉菜单中的“Arrange Schedule（排列计划）”，将出现如图B3.2.0d所示的“排列计划”对话框。	R/W	R/W
File  Exit （文件退出）	退出面板。	R/W	R/W
Edit  OPC Server（编辑OPC服务器）	通过单击“Edit（编辑）”下拉菜单中的“OPC Server（OPC服务器）”，将出现如图C2.1.1所示的OPC服务器对话框。	R/W	R/W

---

原文：

Future Value Type	When selected, the data is collected after pushing “Start” button via the specified OPC DA server.	R/W	R/W
Past Value	When selected, the data between the start time to the end time is collected via OPC HDA server specified.	R/W	R/W
Period	Data acquisition period. It is effective when selecting Future Value Type. Either of “Period” or “No of samples” are selected.	R/W	R/W
No of samples	Number of samples to be generated. It is effective when selecting Future Value Type. Either of “Period” or “No of samples” are selected.	R/W	R/W
Start Time / End Time	Start time and end time to be generated. Data format is ”MM/DD/YYYY HH:MI:SS”. Default value of End Time is “Now”.	R/W	R/W
Acquisition Cycle	Acquisition cycle specifies the data acquisition period. Unit is selectable among Hour / Minute / Second.	R/W	R/W
Start	By clicking “start”, the data acquisition will start. Illegal data and Bad/Questionable data are also checked and marked.	R/W	R/W
Terminate	By clicking “Terminate”, the data acquisition will stop on the way.	R/W	R/W
File  Create New Definition File	By clicking “Import Task” from the “File “ pull down menu, Import Task dialog will appear as shown in Figure B3.2.0b. it copies the selected definition to the scheduler configuration folder.	R/W	R/W
File Open Definition File	By clicking “Append Task” from the “File “ pull down menu, Append Task dialog will appear shown in Figure B3.0.0c. It appends the selected controller to the scheduler.	R/W	R/W
File  Save Definition File	By clicking “Remove Task” from the “File “ pull down menu, Remove Task dialog will appear shown in Figure B3.0.0c. It will remove the selected controller from the scheduler.	R/W	R/W
File  Save Definition File As…	By clicking “Export Task” from the “File “ pull down menu, Export dialog will appear as shown in Figure B3.2.0b. it copies the selected definition to the scheduler configuration folder.	R/W	R/W
File  Open Data File	By clicking “Arrange Schedule” from the “Edit “ pull down menu, Arrange Schedule dialog will appear as shown in Figure B3.2.0d.	R/W	R/W
File  Exit	Exit the panel.	R/W	R/W
Edit  OPC Server	By clicking “OPC Server” from the “Edit “ pull down menu, OPC Server dialog will appear as shown in Figure C2.1.1	R/W	R/W

---

2017.2.21