centos7 安装后需要做的事情

安装centos 7 系统之后要做的几件事

#修改主机名
hostnamectl --static set-hostname xd-1

vim /etc/hosts
127.0.0.1 xd-1
x.x.x.x xd-1

#下面是使用iptables
systemctl stop firewalld.service
systemctl disable firewalld.service
yum -y install iptables-services

adduser wwwad
passwd wwwad

vim /etc/ssh/sshd_config

Port 10999
PermitRootLogin no
systemctl restart sshd.services

visudo
wwwad ALL = (root) NOPASSWD: WWWAD
Cmnd_Alias WWWAD = ALL

#加大打开文件数的限制（open files）
ulimit -n
ulimit -a
vi /etc/security/limits.conf
最后添加

• soft nofile 1024000
• hard nofile 1024000
  hive - nofile 1024000
  hive - nproc 1024000

用户进程限制
[root@hequan ~]# sed -i ‘s#4096#65535#g’ /etc/security/limits.d/20-nproc.conf #加大普通用户限制 也可以改为unlimited
[root@hequan ~]# egrep -v “^$|#” /etc/security/limits.d/20-nproc.conf

•      soft    nproc     65535
  

root soft nproc unlimited

reboot

vim /etc/sysctl.conf
#CTCDN系统优化参数
#关闭ipv6
net.ipv6.conf.all.disable_ipv6 = 1
net.ipv6.conf.default.disable_ipv6 = 1
#决定检查过期多久邻居条目
net.ipv4.neigh.default.gc_stale_time=120
#使用arp_announce / arp_ignore解决ARP映射问题
net.ipv4.conf.default.arp_announce = 2
net.ipv4.conf.all.arp_announce=2
net.ipv4.conf.lo.arp_announce=2
#避免放大攻击
net.ipv4.icmp_echo_ignore_broadcasts = 1
#开启恶意icmp错误消息保护
net.ipv4.icmp_ignore_bogus_error_responses = 1
#关闭路由转发
net.ipv4.ip_forward = 0
net.ipv4.conf.all.send_redirects = 0
net.ipv4.conf.default.send_redirects = 0
#开启反向路径过滤
net.ipv4.conf.all.rp_filter = 1
net.ipv4.conf.default.rp_filter = 1
#处理无源路由的包
net.ipv4.conf.all.accept_source_route = 0
net.ipv4.conf.default.accept_source_route = 0
#关闭sysrq功能
kernel.sysrq = 0
#core文件名中添加pid作为扩展名
kernel.core_uses_pid = 1
#开启SYN洪水攻击保护
net.ipv4.tcp_syncookies = 1
#修改消息队列长度
kernel.msgmnb = 65536
kernel.msgmax = 65536
#设置最大内存共享段大小bytes
kernel.shmmax = 68719476736
kernel.shmall = 4294967296
#timewait的数量，默认180000
net.ipv4.tcp_max_tw_buckets = 6000
net.ipv4.tcp_sack = 1
net.ipv4.tcp_window_scaling = 1
net.ipv4.tcp_rmem = 4096 87380 4194304
net.ipv4.tcp_wmem = 4096 16384 4194304
net.core.wmem_default = 8388608
net.core.rmem_default = 8388608
net.core.rmem_max = 16777216
net.core.wmem_max = 16777216
#每个网络接口接收数据包的速率比内核处理这些包的速率快时，允许送到队列的数据包的最大数目
net.core.netdev_max_backlog = 262144
#限制仅仅是为了防止简单的DoS 攻击
net.ipv4.tcp_max_orphans = 3276800
#未收到客户端确认信息的连接请求的最大值
net.ipv4.tcp_max_syn_backlog = 262144
net.ipv4.tcp_timestamps = 0
#内核放弃建立连接之前发送SYNACK 包的数量
net.ipv4.tcp_synack_retries = 1
#内核放弃建立连接之前发送SYN 包的数量
net.ipv4.tcp_syn_retries = 1
#启用timewait 快速回收
net.ipv4.tcp_tw_recycle = 1
#开启重用。允许将TIME-WAIT sockets 重新用于新的TCP 连接
net.ipv4.tcp_tw_reuse = 1
net.ipv4.tcp_mem = 94500000 915000000 927000000
net.ipv4.tcp_fin_timeout = 1
#当keepalive 起用的时候，TCP 发送keepalive 消息的频度。缺省是2 小时
net.ipv4.tcp_keepalive_time = 1800
net.ipv4.tcp_keepalive_probes = 3
net.ipv4.tcp_keepalive_intvl = 15
#允许系统打开的端口范围
net.ipv4.ip_local_port_range = 1024 65000
#修改防火墙表大小，默认65536
net.netfilter.nf_conntrack_max=655350
net.netfilter.nf_conntrack_tcp_timeout_established=1200
#确保无人能修改路由表
net.ipv4.conf.all.accept_redirects = 0
net.ipv4.conf.default.accept_redirects = 0
net.ipv4.conf.all.secure_redirects = 0
net.ipv4.conf.default.secure_redirects = 0

sysctl -p

#同步时间
ntpdate time.nist.gov
hwclock -w #先同步一遍时间到硬件时间