控制周期
目标 规范
Main controller （主控制器） 10 - 3600 seconds *2
Sub controller（子控制器） 10 - 3600 seconds
- 2 不能指定比子控制器更慢的周期。
控制器名称
目标 规范
Main controller（主控制器） 最多10个字符。不允许使用空格。
Sub controller（子控制器） 主控制器名加子控制器名的总和最多为24个字符。只允许英文和数字。不允许使用空格。
Estimator(预估器) 最多10个字符。只允许英文和数字。不允许使用空格。
Exasmoc客户端数量
5个以下。
控制器控制状态
主控制器状态
状态 过程状态
OFF SMOC控制器停止。
STANDBY 仅监视数据（模型正在更新）。
CONTROL 执行控制(不包括经济函数)。
OPTIMIZE 执行控制(包括经济函数)。
子控制器状态
状态 处理状态
INANCTIVE 仅监控数据。无MV输出。
ACTIVE 执行控制。
CALC计算状态
状态 处理状态
INANCTIVE 仅进行数据监控，无计算输出。
ACTIVE 执行计算。
调整参数
在操作期间，SMOC控制器将参数保存在稍后描述的定义文件中，并且当重新启动时将该文件中保存的值设置为初始值。
保存/恢复的时间
可以根据以下时序保存和恢复整定参数。
分类 定时 细节
Save（保存） 当模式改变时 STANDBY ->CONTROL/OPTIMIZE
当模式改变时 CONTROL ->STANDBY/OPTIMIZE
当模式改变时 OPTIMIZE ->STANDBY/CONTROL
终止 STANDBY ->OFF
固定时间 每15分钟自动保存。
单击“Save SMOC”按钮时 控制面板
Restore（恢复） 启动时
当需要初始化时
需要在线调试时
调整参数目标数据
保存/恢复作为调整参数的目标数据是在HMI上可以更改该值的所有数据。然而，分配给DCS位号的数据不是参数调整的目标。
定义文件
初始化是在操作期间将定义文件重新读取到SMOC控制器的功能。初始化需求通过需求操作在SMOC系统控制面板上执行。
在线整定
在线整定是一个在Exasmoc侧重建SMOC控制器模型的功能。 重建模型保存在定义文件中。 在线整定请求通过请求操作在SMOC系统控制面板上执行。在在线整定功能中，模型重建后，重建模型在操作过程中重新读取并反映在SMOC控制器的运行中。
原文：
Control Period
Object Specification
Main controller 10 - 3600 seconds *2
Sub controller 10 - 3600 seconds
*2. Slower period than that of the sub controller cannot be specified.
Controller Name
Object Specification
Main controller Up to 10 characters. Space is not allowed
Sub controller Sum of Main Controller name plus Sub Controller name is up to 24 characters. Only English and numeric. Space is not allowed
Estimator Up to 10 characters. Only English and numeric Space is not allowed
Number of Exasmoc Client
5 or less are recommended.
Controller Control Status
Main controller status
Status Processing state
OFF SMOC controller' stops
STANDBY Only data monitoring (The model is being updated.)
CONTROL On control execution (An economic function is not included.)
OPTIMIZE On control execution (An economic function is included.)
Sub controller status
Status Processing state
INANCTIVE Only data monitoring. No MV output.
ACTIVE On control execution
CALC calculation status
Status Processing state
INANCTIVE Only data monitoring and calculation No output
ACTIVE On calculation execution
Tuning Parameter
The SMOC controller saves the parameter during operation in the definition file described later, and sets the value saved in the file as an initial value when it is restarted.
Timing of Save/Restore
The tuning parameters can be saved and restored according to the following timing.
Classification Timing Details
Save When the mode is changed STANDBY ->CONTROL/OPTIMIZE
When the mode is changed CONTROL ->STANDBY/OPTIMIZE
When the mode is changed OPTIMIZE ->STANDBY/CONTROL
At termination STANDBY ->OFF
At Fixed period Automatic saving of 15 minute period
When ‘Save SMOC’ button is clicked Control Panel
Restore
When it is started
When initialization is demanded
When online tuning is demanded
Tuning Parameter Target Data
The target data for saving/restoring as the tuning parameter is all data that the value can be changed on HMI. However, the data allocated to the DCS tag is not the target of the tuning parameter.
Definition file
Initialization is a function to reread the definition file to the SMOC controller during operation. The initialization demand is executed on the SMOC system control panel by the demand operation.
Online Tuning
Online tuning is a function to reconstruct the model of the SMOC controller on the Exasmoc side. The restructured model is saved in the definition file. The online tuning demand is executed on the SMOC system control panel by the demand operation. In the online tuning function, after the model is restructured, the restructured model is reread and reflected in the operation of the SMOC controller during operation.
2017.3.25