Huangcn

oracle安装对OS的要求

今天为了查看oracle 10g RAC能否在linux red hat5.7上面安装，看了以下文档，记录一下：

Oracle Database (RDBMS) on Unix AIX,HP-UX,Linux,Mac OS X,Solaris,Tru64 Unix Operating Systems Installation and Configuration Requirements Quick Reference (8.0.5 to 11.2) [ID 169706.1]

Jump to:

AIX
HP-UX (PA-RISC and Itanium)
Linux x86
Linux x86-64
Linux Itanium
Linux on Power
Linux on zSeries
Mac OS X (PowerPC and x86-64)
Oracle Solaris (SPARC and x86-64)
Tru64
Pre-Installation Scripts
OPatch
Related Documents
OS Specific Commands
Change History
Note 43208.1 Certified Compilers

Browse The Contents of Linux Brands ISOs

PURPOSE
--------------

This bulletin is produced to provide a central source for all the primary installation settings for the various mainstream unix platforms, e.g. IBM AIX, HP-UX, Oracle Solaris, Tru64, and Linux.

Careful comparison of the Installation Guide and the applicable release note for an OS/Oracle version has been done to ensure that this bulletin provides the most complete source of data in hopes that it will save time for each researching analyst.

Keeping the OS kernel current helps stabilize the system. Production systems should never run an out dated OS kernel version. As a best practice, Oracle recommends the OS kernel version be maintained to within 6 months of current. Please contact the OS vendor directly for more information, risk exposure, and patching recommendations.

NOTE: Pre-compilers requirements are no longer addressed in this note, for a single source note
that addresses Pre-compiler/Compiler requirements, please refer to:
Note 43208.1 Certified Compilers

SCOPE & APPLICATION
-------------------------------------

This focus of this bulletin is on assisting the Oracle Unix installation community in resolving installation issues of the RDBMS.
This bulletin places in one document all the pertinent information related to installations that has been extracted from three different documents (Installation Guides, Release Notes, and SRNs)

DISCLAIMER
------------

Whenever a contradiction arises between this document and My Oracle Support (MOS)-Certification, My Oracle Support (MOS)-Certification is the Certification authority.
Users of this bulletin are obligated to provide real-time corrections/updates in the form of My Oracle Support (MOS) "Feedback" submissions to ensure the accuracy and up-to-date status of this bulletin.

PRE-INSTALLATION SCRIPTS
-------------------------------------

A decommissioned, non-supported script is still available to verify that the system has been configured correctly according to the 8.0.5 through 9.2 Installation Guides, please refer to the following My Oracle Support (MOS) Note for details:
Note 189256.1 "UNIX: Script to Verify Installation Requirements for Oracle 8.0.5 to 9.2 versions of RDBMS"

The Remote Diagnostic Agent RDA (see Note 314422.1 for more info on RDA) has the capability to run a Pre-Installation check on several 10.1 and 10.2 Unix/Linux Platforms.
Please refer to Note 250262.1 for specifics on how to run these Pre-Install scripts on your server.

OPatch FAQ
-------------------------------------

To apply one-off patches and Critical Patch Updates (CPUs) or Patch Set Update (PSU) on 9.2 and higer RDBMS versions you have to use the patching utility, OPatch.
Oracle Support requests you always use the latest version before applying any patches to your server, to get the latest version,
For 9.2 and 10.1 download Patch 6880880
For 10.2, 11.1 & 11.2 download Patch 6880880
Master Note For OPatch Note 293369.1

Oracle Version 11.2 11.1 10.2 10.1 9.2.0 9.0.1 8.1.7 8.1.6 8.1.5 8.0.6 8.0.5

AIX OS
(32- and 64-bit stands for Oracle not OS)

AIX 5L V5.3 TL 09 SP1 ("5300-09-01") or higher, 64 bit kernel (Part Number E10854-01)

AIX 6.1 TL 02 SP1 ("6100-02-01") or higher, 64-bit kernel

AIX 7.1 TL 00 SP1 ("7100-00-01") or higher, 64-bit kernel

AIX 6.1L, AIX 5L version 5.3, TL 05, Service Pack 06 (Part Number B32076-03), AIX 6L version 6.1, TL 00, Service Pack 04 or later (Part Number B32076-03)

5.2 ML4 or higher, 5.3 ML2 or higher, 6.1

For AIX 6.1, only 10.2.0.3 or higher are certified

Customers running on 10.2.0.4 or higher and using CRS require AIX 5.3 TL5 (5300-05) or higher -- see Note:739371.1

5.2 ML1 or higher, 5.3

o 4.3.3 (64bit only)
o 5.1, 5.2, 5.3 (5L)(64bit only)

4.3.3 (64bit)

o 4.3.2, 4.3.3 (32bit)
o 5.1, 5.2 (5L) (32bit) [patch 2896876 is required if kernel is running in 64bit mode]
o 4.3.2, 4.3.3 (64bit)

4.3.2, 4.3.3 (32 or 64bit)

o 4.2.1 , 4.3.0, 4.3.1, 4.3.2, 4.3.3 (32bit)
o 4.3.2, 4.3.3 (64bit)

o 4.2.1, 4.3.2, 4.3.3 (32bit)
o 4.3.2, 4.3.3 (64bit)

o 4.1.4, 4.1.5, 4.2.1, 4.3.2, 4.3.3 (32bit)
o 4.3.2, 4.3.3 (64bit)

AIX Disk Space 6.40G Database
1.55G Software 6.45G Database
1.6G Software 1.2G Database
3G Software
1G Companion
150M-1.9G Client 1.2G Database
3G Software
1G Companion
150M-1.9G Client 4.5G 4.7G 1.58G 800Mb 800Mb 700Mb 700Mb

AIX RAM

Database: minimum 1GB, recommended 2GB

Grid Infrastructure for standalone server: minimum 1.5GB (plus another 1GB if installing Database too), recommended 4GB

1GB

512Mb
256Mb(Client/Compan)

512Mb

256Mb

128Mb

64Mb or
128Mb / ConText

32Mb or
128Mb / ConText

AIX swap Between 1GB and 2GB then 1.5 times RAM
Between 2GB and 16 GB then match RAM
More than 16 GB then 16GB RAM If RAM = 1024MB to 2048Mb
then 1.5 times RAM
elseif RAM > 2048MB and < 8192MB
then match RAM
else RAM > 8192MB
then .75 times RAM If RAM = 1024MB to 2048Mb
then 1.5 times RAM
elseif RAM > 2048MB and < 8192MB
then match RAM
else RAM > 8192MB
then .75 times RAM 1Gb or match RAM
512Mb(Client/Compan) 1Gb or match RAM 400Mb 400Mb 400Mb 256Mb 2*RAM 2*RAM

AIX tmp 1GB 240Mb 400Mb 400Mb 400Mb 400Mb 400Mb 400Mb 50Mb 20Mb 20Mb

AIX JDK & JRE IBM JDK 1.6.0.00 (64 BIT) IBM JDK 1.5.0.06 (IA64 - mixed mode) is installed IBM JDK 1.4.2 (32bit) is installed IBM JDK 1.4.1.2 (32bit) is installed JDK 1.3.1-build 20020316 & 1.1.8-Build 20020313 JDK 1.2.2.04 or JDK 1.2.2 & 1.1.8 JDK 1.1.8 / 1.2.2 & 1.1.8.3 1.1.8.3 ? n/a n/a

AIX Patches/
Packages

versions in parens mean if OS is later than the listed version, the APAR is built into the later OS version and need not be applied. IMPORTANT: Review Note 390656.1 & apply AIX & Oracle Patch

AIX 5.3 required packages:
bos.adt.base
bos.adt.lib
bos.adt.libm
bos.perf.libperfstat 5.3.9.0 or later
bos.perf.perfstat
bos.perf.proctools
rsct.basic.rte (For RAC configurations only)
rsct.compat.clients.rte (For RAC configurations only)
xlC.aix50.rte:10.1.0.0 or later
gpfs.base 3.2.1.8 or later (Only for RAC systems that will use GPFS cluster filesystems)

AIX 6.1 required packages:
bos.adt.base
bos.adt.lib
bos.adt.libm
bos.perf.libperfstat 6.1.2.1 or later
bos.perf.perfstat
bos.perf.proctools
rsct.basic.rte (For RAC configurations only)
rsct.compat.clients.rte (For RAC configurations only)
xlC.aix61.rte:10.1.0.0 or later
gpfs.base 3.2.1.8 or later (Only for RAC systems that will use GPFS cluster filesystems)

AIX 7.1 required packages:
bos.adt.base
bos.adt.lib
bos.adt.libm
bos.perf.libperfstat
bos.perf.perfstat
bos.perf.proctools
xlC.aix61.rte.10.1.0.0 or later
xlC.rte.10.1.0.0 or later
gpfs.base 3.3.0.11 or later (Only for RAC systems that will use GPFS cluster filesystems)

Authorized Problem Analysis Reports (APARs) for AIX 5.3:
IZ42940
IZ49516
IZ52331
See Note:1379753.1 for other AIX 5.3 patches that may be required

APARs for AIX 6.1:
IZ41855
IZ51456
IZ52319
IZ97457
IZ89165
See Note:1264074.1 andNote:1379753.1 for other AIX 6.1 patches that may be required

APARs for AIX 7.1:
IZ87216
IZ87564
IZ89165
IZ97035
See Note:1264074.1 andNote:1379753.1 for other AIX 7.1 patches that may be required

Refer to the 11.2 AIX Install Guide.Part Number E24332-01

6.1 / 5.3 ML5 required packages:
bos.adt.base
bos.adt.lib
bos.adt.libm
bos.perf.libperfstat
bos.perf.perfstat
bos.perf.proctools
xlC.aix50.rte:8.0.0.7 or later (AIX 5.3)
xlC.rte:8.0.0.7 or later (AIX 5.3)
xlC.aix61.rte:9.0.0.1 or later (AIX 6.1)
xlC.rte:9.0.0.1 or later (AIX 6.1)
rsct.basic.rte (For RAC configurations only)
rsct.compat.clients.rte (For RAC configurations only)

5.3 ML5 required patches:
IY89080
IY92037
IY94343
IZ01060 or efix for IZ01060
IZ03260 or efix for IZ03260 (IZ03260 for ML6, IZ03475 for ML7) to address ORA-27061
IY84780
IY68989

POWER7 Based Hardware
Patch 9216848 (Note 1065579.1)

5.2 ML4 required patches:
IY63133
IY64978
IY63366
IY64691
IY64737
IY65001
IY94343 Note 422031.1 LV Block Corruption

5.3 ML2 required patches:
IY58143
IY59386
IY60930
IY66513
IY70159
IY68989
IY94343 Note 422031.1 LV Block Corruption
Patch 5496862 is required (See Note 390656.1) if running on AIX 5.3 ML5
IY84780
IY68989

Important: Please see Note 282036.1 for the latest patching requirements for 5.3 and 5.2

Required OS packages:
bos.adt.base
bos.adt.lib
bos.adt.libm
bos.perf.perfstat
bos.perf.libperfstat
bos.perf.proctools

6.1 specifics:
Please download and run an updated version of rootpre.script before proceeding with the Oracle Database install. Internal bug 6613550. 6718715can be downloaded from My Oracle Support (MOS).
Refer to Note 282036.1 for updates on any required patches for AIX 6.1

5.2 required patches:
IY43980
IY44810
IY45462
IY45707
IY46214
IY46605
IY48525
IY51801
IY59082 Refer to Note 285158.1
IY94343 Note 422031.1 LV Block Corruption

5.3 required patches: Refer to Note 282036.1
IY58143
IY59386
IY60930
IY94343 Note 422031.1 LV Block Corruption
Patch 5496862 is required (See Note 390656.1) if running on AIX 5.3 ML5.
IY84780
IY68989

Important: Please see Note 282036.1 for the latest patching requirements for 5.3 and 5.2

Required OS packages:
bos.adt.base
bos.adt.lib
bos.adt.libm
bos.perf.perfstat
bos.perf.libperfstat
bos.perf.proctools
X11.motif.lib (Spatial only)

Async IO Hang, refer to Note 233659.1 for applicable patch for 4.3.3, 5.1, or 5.2

4.3.3 required patches/packages:
IY30927(4.3.3.0.10)
IY24568(4.3.3.0.09)
IY25282(4.3.3.0.09)
IY27614(4.3.3.0.09)
IY30151(4.3.3.0.10)
Maint Level 9 or higher (4.3.3.0.09)

bos.adt.base
bos.adt.lib
bos.adt.libm
bos.perf.perfstat

5.1(5L) required patches/packages:
IY26778(5100-01)
IY28766(5100-01)
IY28949(5100-01)
IY29965(5100-02)
IY30150(5100-02)
IY59082 refer to Note 285158.1
Maint Level 1 and IY22854

bos.adt.base
bos.adt.lib
bos.adt.libm
bos.perf.perfstat
bos.perf.libperfstat
Use the -ignoreSysPrereqs option with runInstaller to ignore the system pre-requisite test (Note 293750.1)

Maint Level 7 or higher (4.3.3.0.07)

bos.adt.base
bos.adt.lib
bos.adt.libm
bos.perf.perfstat
X11.apps.rte
X11.apps.xterm
X11.base.rte
X11.motif.lib
X11.motif.mwm

IY01050 (4.3.3.0.03)
IY07276 (4.3.3.0.02)
IY05995 (4.3.3.01)
IY02407 (4.3.2.02)
IX89087 (4.3.2.0.02)
IY03412 (4.3.2.0.02)
IX85104 (4.3.2.0.01)
IX87313 (4.3.2.0.01)
IX87382 (4.3.2.0.01)
IX89552 (4.3.2.0.01)
IX81863 (4.3.1)
IX72696 (4.3.0)

IY01050 (4.3.3.0.03)
IY07276 (4.3.3.0.02)
IY05995 (4.3.3.01)
IY07018 (4.3.3)
IY02407 (4.3.2.02)
IX89087 (4.3.2.0.02)
IY03412 (4.3.2.0.02)
IX85104 (4.3.2.0.01)
IX87313 (4.3.2.0.01)
IX87382 (4.3.2.0.01)
IX89552 (4.3.2.0.01)
IX81863 (4.3.1)
IX72696 (4.3.0)

4.2 related required APARs
IX62429 (4.2.0)
IX67174 (4.2.0)
IX67978 (4.2.1)
IX68932 (4.2.1)
IX70737 (4.2.1)
IX78933 (4.2.1.0.03)
IX81957 (4.2.1.0.03)
IX86229 (4.2.1.0.05)

4.3 related required APARs
IX71948 (4.3.0)
IX79690 (4.3.0)
IX81863 (4.3.1)

bos.adt.base, bos.adt.libm
must be installed

4.2 related required APARs
IX62429 (4.2.0)
IX67174 (4.2.0)
IX67978 (4.2.1)
IX68932 (4.2.1)
IX70737 (4.2.1)
IX78933 (4.2.1.0.03)
IX81957 (4.2.1.0.03)
IX86229 (4.2.1.0.05)
IX88178 (4.2.1.0.06)

4.3 related required APARs
IX71948 (4.3.0)
IX79690 (4.3.0)
IX81863 (4.3.1)
IX87313 (4.3.2.0.01)
IX87382 (4.3.2.0.01)
IX89087 (4.3.2.0.02)

bos.adt.base, bos.adt.libm
must be installed

4.1 related required APARs
IX54124 (4.1.4)
IX55203 (4.1.5.0.01)
IX62330 (4.1.5)
IX58455 (4.1.4)
IX61237 (4.1.4)
IX67074 (4.1.5)
IX61933 (4.1.5)
IX70194 (4.1.5)

4.2 related required APARs
IX62429 (4.2.0)
IX67174 (4.2.0)
IX67978 (4.2.1)
IX68932 (4.2.1)
IX70737 (4.2.1)
If running 4.2 then need bos.rte.libc version 4.2.0.5

4.3 related required APARs
IX71948 (4.3.0)

AIX Kernel Settings

set AIXTHREAD_SCOPE=S in the environment:
export AIXTHREAD_SCOPE=S

NOTE: This is only necessary on AIX5L. A change was introduced in AIX 6.1 which means that the variable does not need to be set. See section 5.5 (page 217) of theIBM AIX Version 6.1 Differences Guide

From Section 2.5 of the 11.2 Install Guide for AIX:

2.5 Verifying UDP and TCP Kernel Parameters

Use NDD to ensure that the kernel TCP/IP ephemeral port range is broad enough to provide enough ephemeral ports for the anticipated server workload. Ensure that the lower range is set to at least 9000 or higher, to avoid Well Known ports, and to avoid ports in the Registered Ports range commonly used by Oracle and other server ports. Set the port range high enough to avoid reserved ports for any applications you may intend to use. If the lower value of the range you have is greater than 9000, and the range is large enough for your anticipated workload, then you can ignore OUI warnings regarding the ephemeral port range.

Use the following command to check your current range for ephemeral ports:

# /usr/sbin/no -a | fgrep ephemeral
tcp_ephemeral_low = 32768
tcp_ephemeral_high = 65535
udp_ephemeral_low = 32768
udp_ephemeral_high = 65535

In the preceding example, the TCP and UDP ephemeral ports are set to the default range (32768-65536).

If you expect your workload to require a high number of ephemeral ports, such as high node counts or heavy use of Parallel Query, then update the UDP and TCP ephemeral port range to a broader range. For example:

# /usr/sbin/no -p -o tcp_ephemeral_low=9000 -o tcp_ephemeral_high=65500
# /usr/sbin/no -p -o udp_ephemeral_low=9000 -o udp_ephemeral_high=65500

From Section 2.8.2 of the 11.2 Install Guide for AIX:

2.8.2 Configure System Configuration Parameters

Parameter Recommended Value
maxuprocs 16384
ncargs 128

Also see Note:1307804.1

set AIXTHREAD_SCOPE=S in the environment:
export AIXTHREAD_SCOPE=S

NOTE: This is only necessary on AIX5L. A change was introduced in AIX 6.1 which means that the variable does not need to be set. See section 5.5 (page 217) of theIBM AIX Version 6.1 Differences Guide

set AIXTHREAD_SCOPE=S in the environment:
export AIXTHREAD_SCOPE=S

NOTE: This is only necessary on AIX5L. A change was introduced in AIX 6.1 which means that the variable does not need to be set. See section 5.5 (page 217) of the IBM AIX Version 6.1 Differences Guide

set AIXTHREAD_SCOPE=S in the environment:
export AIXTHREAD_SCOPE=S

N/A

LINK_CNTRL = L_PTHREADS_D7 (if using 4.3)

Oracle Version 11.2 11.1 10.2 10.1 9.2.0 9.0.1 8.1.7 8.1.6 8.1.5 8.0.6 8.0.5

HP OS
(32- and 64-bit stands for Oracle not OS) HP-UX 11i V3 patch Bundle Sep/ 2008 (B.11.31.0809.326a) or higher (Part Number E10851-01) 11.23 and 11.31 (Itanium,PA-RISC) 11.11 (PA-RISC) (64bit)
11.23 (PA-RISC) (64bit)
11.23, 11.31 (PA-RISC / Itanium / IPF) 11.11 (PA-RISC) (64bit)
11.23 (PA-RISC) (64bit)
11.23, 11.31 (IA64 - Itanium)
Note: for all Itanium systems using "Montecito" processors, refer tonote:400227.1 for special installation instructions 11.0 (64bit)
11.11 (64bit)
11.23 (PA-RISC) (64bit)
11.31 (PA-RISC) (64bit)(10/30)
11.22, 11.23, 11.31 (IA64 - Itanium)
Note: for all Itanium systems using "Montecito" processors, refer tonote:400227.1 for special installation instructions 11.0 (64bit)
11.11 (64bit) 11.0, 11.11(11i) (32bit/64bit) 11.0, 11.11(11i) (32bit/64bit) 11.0, 11.11(11i) (32bit/64bit) 10.20 (32bit)
11.0, 11.11(11i) (32bit/64bit) 10.20 (32bit)
11.0 (32 or 64)

HP Disk Space 1.7G database
6.9 G Software 1.7G Database
6.9G Software 1.2G Database
2.5G Software
1G Companion
150M-1.5G Client 1.2G Database
2.5G Software
1G Companion
150M-1.5G Client 4.5G 3.5G 1.5G 910Mb 900Mb 900Mb 900Mb

HP RAM

Database: minimum 1GB, recommended 2GB

Grid Infrastructure for standalone server: minimum 1.5GB (plus another 1GB if installing Database too), recommended 4GB

1GB

512Mb
256Mb(Client/Compan)

512Mb

256Mb

128Mb

64Mb or
128Mb /
ConText

32Mb or
128Mb /
ConText

HP swap Between 4 GB and 8 GB then 2 times RAM.
Between 8 GB and 32 GB then 1.5 times RAM.
More than 32 GB then 32 GB RAM. If RAM = 1GB to 2GB
then 1.5 times RAM
elseif RAM > 2GB and < 8GB
then match RAM
else RAM > 8GB
then .75 times RAM If RAM = 1024MB to 2048Mb
then 1.5 times RAM
elseif RAM > 2048MB and < 8192MB
then match RAM
else RAM > 8192MB
then .75 times RAM 1Gb or match RAM
512Mb(Client/Compan) 1Gb or match RAM 2*RAM 2*RAM 2*RAM 3*RAM 3*RAM 3*RAM

HP tmp 1GB 400Mb 400Mb 400Mb 400Mb 400Mb 75Mb ? 75Mb 50Mb 50Mb

HP jdk & JRE

HPUX JDK 6.0.05, HPUX JDK 5.0.15

NOTE: The JDK version included with 11.2.0.3 on HP-UX Itanium (1.5.0.23) is not compatible with Itanium 2 model 9310 processors. Please refer to the statement at the end of bothNote:404843.1 and Note:552358.1. To workaround the issue, download JDK 1.5.0.24 or higher and use the "./runInstaller -jreLoc ..." syntax to start the 11.2.0.3 installation.

Java 1.5.0.0.6 is installed

Java SDK 1.4.2.00 is installed

JDK 1.3.1.02

JDK 1.2.2.07 & 1.1.8

JDK 1.2.2 & 1.1.8.03

1.1.8.10

1.1.7

n/a

HP Patches/
Packages

"s/b" indicates superseded by

See Note 43507.1for other applicable patches.

For HP-UX 11i V3 (11.31):
PHCO_40381 11.31 Disk Owner Patch
PHCO_41479 11.31 (fixes an 11.2.0.2 ASM disk discovery issue)
PHKL_38038 VM patch - hot patching/Core file creation directory
PHKL_38938 11.31 SCSI cumulative I/O patch
PHKL_39351 Scheduler patch : post wait hang
PHSS_36354 11.31 assembler patch
PHSS_37042 11.31 hppac (packed decimal)
PHSS_37959 Libcl patch for alternate stack issue fix (QXCR1000818011)
PHSS_39094 11.31 linker + fdp cumulative patch
PHSS_39100 11.31 Math Library Cumulative Patch
PHSS_39102 11.31 Integrity Unwind Library
PHSS_38141 11.31 aC++ Runtime
Pro*C/C++, Oracle Call Interface, Oracle C++
Pro*C/C++, Oracle Call Interface, Oracle C++ Call Interface, Oracle XML Developer's Kit (XDK):-
Patch for HP-UX 11i V3 (11.31) on HP-UX Itanium:-
PHSS_39824 - 11.31 HP C/aC++ Compiler (A.06.23) patch

For HP-UX PA-RISC and Itanium 11.23 (Mar '07 Patch bundle for HP-UX 11iV2- B.11.23.0703):
PHSS_35979 s/b PHSS_37201 s/b PHSS_37492 s/b PHSS_38134
PHSS_35978 s/b PHSS_36343 s/b PHSS_38140
PHCO_35524 s/b PHCO_36744
PHKL_35478 s/b PHKL_36319
PHCO_36673 s/b PHCO_37228
PHKL_35029 s/b PHKL_37121
PHKL_37809 or later Note 580273.1

For HP-UX PA-RISC and Itanium 11.31:
PHKL_35900
PHKL_36248
PHKL_36249
PHKL_35936 s/b PHKL_36242 s/b PHKL_37185 s/b PHKL_38038
PHKL_38397 or later. Note 580273.1

Use the -ignoreSysPrereqs option with runInstaller to ignore the system pre-requisite test

Refer to the following Web site for information about additional java patches:http://www.hp.com/products1/unix/java/patches/index.htmlThe default 64bit OS (PA-RISC and ~~Itanium~~ From Bug 8789180) installation does not create a few required X library symbolic links. The following symbolic links need to be created:
(NOTE: This task is required only if the Motif 2.1 Development Environment Package ( X11MotifDevKit.MOTIF21-PRG ) is not installed ).
cd /usr/lib
ln -s /usr/lib/libX11.3 libX11.sl
ln -s /usr/lib/libXIE.2 libXIE.sl
ln -s /usr/lib/libXext.3 libXext.sl
ln -s /usr/lib/libXhp11.3 libXhp11.sl
ln -s /usr/lib/libXi.3 libXi.sl
ln -s /usr/lib/libXm.4 libXm.sl
ln -s /usr/lib/libXp.2 libXp.sl
ln -s /usr/lib/libXt.3 libXt.sl
ln -s /usr/lib/libXtst.2 libXtst.sl

Per HP Bug (Doc ID: KBRC00003627)
NOTE: This bug is not applicable to 11.23 The default 64bit OS (PA-RISC and Itanium) installation does not create a few required X library symbolic links. The following symbolic links need to be created:
(NOTE: This task is required only if the Motif 2.1 Development Environment Package ( X11MotifDevKit.MOTIF21-PRG ) is not installed ).
cd /usr/lib
ln -s /usr/lib/libX11.3 libX11.sl
ln -s /usr/lib/libXIE.2 libXIE.sl
ln -s /usr/lib/libXext.3 libXext.sl
ln -s /usr/lib/libXhp11.3 libXhp11.sl
ln -s /usr/lib/libXi.3 libXi.sl
ln -s /usr/lib/libXm.4 libXm.sl
ln -s /usr/lib/libXp.2 libXp.sl
ln -s /usr/lib/libXt.3 libXt.sl
ln -s /usr/lib/libXtst.2 libXtst.sl

GOLDQPK11i, December 2004 or later
If GOLDQPK is not installed then these two patchkits need to be installed:
GOLDAPPS11i, December 2004 or later
GOLDBASE11i, December 2004 or later

11.11 required patches:
o PHNE_31097 s/b PHNE_32477 s/b PHNE_33498 s/b PHNE_35418 s/b PHNE_36168 s/b PHNE_37110
o PHSS_31221 s/b PHSS_33263 s/b PHSS_33944 s/b PHSS_33945
For JDK, refer to HP Java for latest patches:
o PHSS_30970 s/b PHSS_33033 s/b PHSS_35379 s/b PHSS_35385
For PL/SQL/ProC,OCI,OCCI,XDK:
o PHSS_32508 s/b PHSS_34411 s/b PHSS_35099 s/b PHSS_36087
o PHSS_32509 s/b PHSS_34412 s/b PHSS_35098 s/b PHSS_36086
o PHSS_32510 s/b PHSS_34413 s/b PHSS_35100 s/b PHSS_36088

11.23 (PA-RISC) required patches:
o PHSS_31849 s/b PHSS_37021 s/b PHSS_37492 s/b PHSS_40537
o PHSS_31852 s/b PHSS_35055 s/b PHSS_36343s/b PHSS_38140
For PL/SQL/ProC,OCI,OCCI,XDK:
o PHSS_32511
o PHSS_32512
o PHSS_32513
o PHKL_37809 or later Note 580273.1

Ensure that unzip version is 5.5 or higher ($ unzip -v) [reference Note 263692.1], if not it can be downloadedhere

11.31 (PA-RISC) required patches:
o PHKL_35900: 11.31 evacd performance, kvaddr leak panic
o PHKL_36248: 11.31 esctl cumulative patch
o PHKL_36249: 11.31 esdisk cumulative patch
o PHKL_38397 or later Note 580273.1
o PHKL_35936 s/b PHKL_36242 s/b PHKL_37185 s/b PHKL_38038: 11.31 call to read(2) or write(2) may incorrectly return -1
o You can use HP JDK 5.0.07 with the Oracle Java Database Connectivity and Oracle Call Interface drivers. Ensure that you install the patch PHKL_35029 s/b PHKL_37121 to use JDK 5.0.07.

11.23 (Itanium) required patches:
The following operating system patches:
o BUNDLE11i B.11.23.0409.3: Patch Bundle for HP-UX 11i V2
Note: You must have the August 2004 version of BUNDLE11i B.11.23.0408.1 for HP-UX 11i v2 on your system prior to updating to the HP-UX 11i v2 September 2004 or later release.
o PHCO_32426
o PHKL_32646 s/b PHKL_36103
o PHKL_32632 s/b PHKL_33656 s/b PHKL_33807 s/b PHKL_38364
o PHKL_32645 s/b PHKL_34477 s/b PHKL_37106
o PHKL_33552 s/b PHKL_33563 s/b PHKL_36667 s/b PHKL_37653 s/b PHKL_41002
o PHSS_31850 s/b PHSS_34040 s/b PHSS_37201 s/b PHSS_37492 s/b PHSS_38134 s/b PHSS_40537
o PHSS_31851 s/b PHSS_34043 s/b PHSS_34859 s/b PHSS_37498 s/b PHSS_38138 or PHSS_39101 s/b PHSS_40541
o PHSS_31854 s/b PHSS_33357 s/b PHSS_34045 s/b PHSS_34445 s/b PHSS_40547
o PHSS_31855 s/b PHSS_33350 s/b PHSS_34041 s/b PHSS_35055 s/b PHSS_36343 s/b PHSS_38140 s/b PHSS_40543
o PHSS_33275 s/b PHSS_33349 s/b PHSS_34040 s/b PHSS_37201 s/b PHSS_37492 s/b PHSS_38134 s/b PHSS_40537
o PHSS_33276 s/b PHSS_34042 s/b PHSS_34853 s/b PHSS_36344 s/b PHSS_40539
o PHKL_37809 or later Note 580273.1

For PL/SQL native compilation and installation of Pro*C/C++, Oracle Call Interface, Oracle C++ Call Interface, or Oracle XML Developer's Kit (XDK) , the following patches are required:
o PHSS_33278
o PHSS_33277

The following JDK patches:
o PHCO_31553 s/b PHCO_33675 s/b PHCO_36323 s/b PHCO_37940 s/b PHCO_39699
o PHKL_31500
o PHSS_32213 s/b PHSS_32502 s/b PHSS_34201 s/b PHSS_37492 s/b PHSS_40537
Note: Refer to the following Web site for information about additional patches that may be required by JDK 1.4.2:
HP Java Patches

11.31 (Itanium) required patches:
The following operating system patches:
o PHKL_35936 s/b PHKL_36242 s/b PHKL_37185 s/b PHKL_38449 s/b PHKL_38038
o PHKL_38397 or later Note 580273.1

The following patches are supported on Oracle Database 10g release 2:(Part Number B25292-06)
PHKL_35900: 11.31 evacd performance, kvaddr leak panic
PHKL_36248: 11.31 esctl cumulative patch
PHKL_36249: 11.31 esdisk cumulative patch
PHKL_35936: 11.31 call to read(2) or write(2) may incorrectly return -1

Use the -ignoreSysPrereqs option with runInstaller to ignore the system pre-requisite test

Per HP Bug (Doc ID: KBRC00003627)
NOTE: This bug is not applicable to 11.23 The default 64bit OS installation does not create a few required X library symbolic links. The following symbolic links need to be created:
(NOTE: This task is required only if the Motif 2.1 Development Environment Package ( X11MotifDevKit.MOTIF21-PRG ) is not installed ).
cd /usr/lib
ln -s /usr/lib/libX11.3 libX11.sl
ln -s /usr/lib/libXIE.2 libXIE.sl
ln -s /usr/lib/libXext.3 libXext.sl
ln -s /usr/lib/libXhp11.3 libXhp11.sl
ln -s /usr/lib/libXi.3 libXi.sl
ln -s /usr/lib/libXm.4 libXm.sl
ln -s /usr/lib/libXp.2 libXp.sl
ln -s /usr/lib/libXt.3 libXt.sl
ln -s /usr/lib/libXtst.2 libXtst.sl

GOLDQPK11i, June 2003 or later
If GOLDQPK is not installed then these two patchkits need to be installed:
GOLDAPPS11i, June 2003 or later
GOLDBASE11i, June 2003 or later
Jun03GQPK11i_Aux_Patch (Does not exist, see Bug 3512068)

X11MotifDevKit (spatial only)
o PHCO_28123 s/b PHCO_31314 s/b PHCO_32397
o PHKL_29198 s/b PHKL_32603
o PHNE_28476 s/b PHNE_29825 s/b PHNE_30367 s/b PHNE_31091 s/b PHNE_33729
o PHNE_28923 s/b PHSS_30049 s/b PHNE_32396 s/b PHNE_33704
o PHSS_28871 s/b PHSS_33033
o PHSS_28880 s/b PHSS_32573 s/b PHSS_33263
o PHCO_26331 s/b PHCO_27958 s/b PHCO_33205
o PHCO_29109 s/b PHCO_29960 s/b PHCO_30544
o PHKL_25468 s/b PHKL_30542
o PHKL_25842 s/b PHKL_30288 s/b PHKL_34311
o PHKL_25993
o PHKL_25994 s/b PHKL_32061 s/b PHKL_34309
o PHKL_25995 s/b PHKL_30541 s/b PHKL_32457 s/b PHKL_34024
o PHKL_26468 s/b PHKL_27316 s/b PHKL_30837
o PHKL_28489

HP-UX 11.23 (IA64) Operating System Patches:
o PHSS_29658 s/b PHSS_30015 s/b PHSS_30237
o PHSS_29660

Java SDK 1.4.2 latest patches

Ensure that unzip version is 5.5 or higher ($ unzip -v) [reference Note 263692.1], if not it can be downloadedhere

11.31 (Itanium) required patches:
The following operating system patches:
PHKL_35936 s/b PHKL_36242 s/b PHKL_37185 s/b PHKL_38038
Use the -ignoreSysPrereqs option with runInstaller to ignore the system pre-requisite test

Per HP Bug (Doc ID: KBRC00003627)
NOTE: This bug is not applicable to 11.22,11.23 The default 64bit OS installation does not create a few required X library symbolic links. The following symbolic links need to be created:
cd /usr/lib
ln -s /usr/lib/libX11.3 libX11.sl
ln -s /usr/lib/libXIE.2 libXIE.sl
ln -s /usr/lib/libXext.3 libXext.sl
ln -s /usr/lib/libXhp11.3 libXhp11.sl
ln -s /usr/lib/libXi.3 libXi.sl
ln -s /usr/lib/libXm.4 libXm.sl
ln -s /usr/lib/libXp.2 libXp.sl
ln -s /usr/lib/libXt.3 libXt.sl
ln -s /usr/lib/libXtst.2 libXtst.sl

HP-UX 11.0(64 bit) Operating System Patches:
Sept 2001 Quality Pack
o PHCO_23792 s/b PHCO_26960
o PHCO_24148 s/b PHCO_25707 s/b PHCO_27608 s/b PHCO_28425 s/b PHCO_32448
o PHKL_24268 s/b PHKL_27178 (has been recalled by HP may destroy logical volumes on PVGs - more info s/b PHKL_32920
o PHKL_24729 s/b PHKL_29256
o PHKL_25475 s/b PHKL_27510 s/b PHKL_30553
o PHKL_25525 s/b PHKL_27364 s/b PHKL_28766 s/b PHKL_31867
o PHNE_24715 s/b PHNE_26771 s/b PHNE_29473 s/b PHNE_32041 s/b PHNE_33395
o PHSS_23670 s/b PHSS_26138 s/b PHSS_27858
o PHSS_24301 s/b PHSS_26273 s/b PHSS_28433 (only needed for C++ compiler and Pro*C++)
o PHSS_24303 s/b PHSS_26559 s/b PHSS_30965
o PHSS_24627 s/b PHSS_26945 s/b PHSS_32574
o PHSS_22868 (only needed for C++ compiler and Pro*C++)

Ensure that unzip version is 5.5 or higher ($ unzip -v) [reference Note 263692.1], if not it can be downloaded here

HP-UX 11i (64 Bit) Operating System Patches:
Support Plus Bundle 'December 2002 SP-0212' or later
JDK 1.3.1.02
o PHCO_24402 s/b PHCO_25569 s/b PHCO_31923
o PHCO_28427 s/b PHCO_29029 s/b PHCO_31903 s/b PHCO_33533
o PHKL_25506 s/b PHKL_33457
o PHNE_27144 s/b PHNE_27745 s/b PHNE_30580 (For RAC systems)
o PHNE_28568 s/b PHNE_30378 s/b PHNE_32477 s/b PHNE_33315
o PHSS_26263 s/b PHSS_26560 s/b PHSS_33033
o PHSS_24638 s/b PHSS_26946 s/b PHSS_30966 s/b PHSS_33263
o PHSS_26774 s/b PHSS_28849 s/b PHSS_30742 (For ServiceGuard 11.13 systems)

HP-UX 11.22 /11.23 (IA64) Operating System Patches:
o PHSS_27284 s/b PHSS_28977
o PHSS_27285 s/b PHSS_28970
o PHSS_27286 s/b PHSS_28978
o PHSS_27287 s/b PHSS_29652
o PHSS_27288 s/b PHSS_28971
o PHSS_27289 s/b PHSS_29653
o PHSS_27290 s/b PHSS_28973
o PHSS_27291 s/b PHSS_28969
o PHSS_27292 s/b PHSS_29654
o PHSS_27293 s/b PHSS_28975
o PHKL_28465

HP-UX 11.0(64 bit) Operating System Patches:
Dec 2000 patch bundle
o PHCO_23092 s/b PHCO_23963 s/b PHCO_26111
o PHCO_23770 s/b PHCO_25707 s/b PHCO_27608
o PHCO_23919 s/b PHCO_27340
o PHKL_18543
o PHKL_23226 s/b PHKL_27510 s/b PHKL_30553
o PHKL_23813 s/b PHKL_25525 s/b PHKL_27364 s/b PHKL_31867
o PHKL_23814 s/b PHKL_24729 s/b PHKL_29256
o PHKL_23815 s/b PHKL_26337 s/b PHKL_27553
o PHKL_23857 s/b PHKL_25525 s/b PHKL_27364 s/b PHKL_31867

HP-UX 11i (64 bit) Operating System Patches Status
o PHCO_23094 s/b PHCO_24402
o PHCO_23772 s/b PHCO_26124 s/b PHCO_27910
o PHSS_23441 s/b PHSS_26263
o PHNE_23502 s/b PHNE_25625 s/b PHNE_26388 s/b PHNE_28568

11.0 patches:
o PHSS_21947 s/b PHSS_24303 s/b PHSS_26559
o PHNE_20316 s/b PHNE_22566 s/b PHNE_25440
o PHKL_21392 s/b PHKL_24027
o PHKL_22145 s/b PHKL_25475 s/b PHKL_27510 s/b PHKL_30553
o PHKL_22266 s/b PHKL_27178

DART 49, 6/00

Patch Bundle9905
o PHCO_17556 s/b PHCO_23651
o PHCO_17792 s/b PHCO_21187 s/b PHCO_25902
o PHCO_18229 s/b PHCO_23963 s/b PHCO_26111
o PHCO_19491 s/b PHCO_25707 s/b PHCO_27608
o PHCO_19666 s/b PHCO_23792 s/b PHSS_26960
o PHKL_14750 s/b PHKL_25475 s/b PHKL_27510 s/b PHKL_30553
o PHKL_17038 s/b PHKL_25525 s/b PHKL_27364 s/b PHKL_31867
o PHKL_18543
o PHKL_19800 s/b PHKL_24027
o PHKL_20016
o PHKL_20079 s/b PHKL_24027
o PHNE_19616 s/b PHNE_24100 s/b PHNE_25385
o PHSS_14582 s/b PHSS_26320
o PHSS_15853 s/b PHSS_23546 s/b PHSS_26566
o PHSS_16849 s/b PHSS_25718 s/b PHSS_27469
o PHSS_17535 s/b PHSS_25091
o PHSS_18066
o PHSS_18110 s/b PHSS_26273 s/b PHSS_28433
o PHSS_18430 s/b PHSS_25199 s/b PHSS_26495
o PHSS_18649 s/b PHSS_26320
o PHSS_19593 s/b PHSS_25447 s/b PHSS_27230
o PHSS_19178 s/b PHSS_25249
o PHSS_19748 s/b PHSS_25149 s/b PHSS_26490
o PHSS_19866 s/b PHSS_24303 s/b PHSS_26559
o PHSS_20544 s/b PHSS_26138 s/b PHSS_27858
o PHSS_20014 s/b PHSS_24303 s/b PHSS_26559
o PHSS_21180

PHKL_14750 s/b PHKL_25475 s/b PHKL_27510 s/b PHKL_30553
o PHKL_17709 s/b PHKL_23792 s/b PHKL_26960
o PHKL_17869 s/b PHKL_18543
o PHNE_17446 s/b PHNE_21767 s/b PHNE_26771 s/b PHNE_29473

32/64bit 11.0
o PHNE_15995 s/b PHNE_21767 s/b PHNE_26771 s/b PHNE_29473
o PHNE_16283 s/b PHNE_21767 s/b PHNE_26771 s/b PHNE_29473

64bit 11.0
o PHSS_15316 s/b PHSS_24303 s/b PHSS_26559
o PHSS_16404 s/b PHSS_24303 s/b PHSS_26559

32/64bit 11.0
o PHNE_15995 s/b PHNE_21767 s/b PHNE_26771 s/b PHNE_29473
o PHNE_16283 s/b PHNE_21767 s/b PHNE_26771 s/b PHNE_29473

64bit 11.0
o PHSS_15316 s/b PHSS_24303 s/b PHSS_26559
o PHSS_16404 s/b PHSS_24303 s/b PHSS_26559

HP Kernel Settings

Refer to the 11GR2 HP-UX Install Guide for steps to do this. Section 2.8 Configuring Kernel Parameters on HP-UX Systems.Part Number E24336-02.

Important: For HP 9000/700 workstations Only, see Note 467166.1:
set the following before starting the OUI,DBCA, or DBUA:
$ export JAVA64FLAG="-d64"

KSI_ALLOC_MAX (NPROC*8)
EXECUTABLE_STACK=0
MAX_THREAD_PROC 1024
MAXDSIZ 1073741824
MAXDSIZ_64BIT 2147483648
MAXFILES 65536 Note:1061351.1
MAXFILES_LIM 65536 Note:1061351.1
MAXTSIZE_64BIT 1073741824
MAXSSIZ 134217728 bytes
MAXSSIZ_64BIT 1073741824
MAXUPRC ((NPROC*9)/10)+1 Bug 6995956
MSGMAP (MSGTQL+2) *
MSGMNI (NPROC)
MSGSEG 32767 *
MSGTQL (NPROC)
NCSIZE (NINODE+1024)
NFILE (15*NPROC+2048) *
NFLOCKS (NPROC)
NINODE (8*NPROC+2048)
NKTHREAD (((NPROC*7)/4)+16)
NPROC 4096
SEMMNI (NPROC)
SEMMNS (SEMMNI*2)
SEMMNU (NPROC - 4)
SEMVMX 32767
SHMMAX AvailMem
SHMMNI 4096
SHMSEG 512
VPS_CEILING 64

* MSGMAP,MAXSWAPCHUNKS, NCALLOUT, SEMMAP,VX_NCSIZE,NFILE, MSGSEG are obsolete on 11.31 (Itanium and PA-RISC) and no longer required to be set.

KSI_ALLOC_MAX (NPROC*8)
EXECUTABLE_STACK=0
MAX_THREAD_PROC 1024
MAXDSIZ 1073741824 bytes
MAXDSIZ_64BIT 2147483648 bytes
MAXFILES 65536 Note:1061351.1
MAXFILES_LIM 65536 Note:1061351.1
MAXSSIZ 134217728 bytes
MAXSSIZ_64BIT 1073741824
MAXSWAPCHUNKS 16384*
MAXUPRC ((NPROC*9)/10)+1 Bug 6995956
MSGMAP (MSGTQL+2)
MSGMNI (NPROC)
MSGSEG 32767
MSGTQL (NPROC) (B25293-01)
NCSIZE (NINODE+1024)*
NFILE (15*NPROC+2048)
NFLOCKS (NPROC) (B25293-01)
NINODE (8*NPROC+2048)
NKTHREAD (((NPROC*7)/4)+16)
NPROC 4096
SEMMAP (SEMMNI+2)*
SEMMNI (NPROC) (B25293-01)
SEMMNS (SEMMNI*2)
SEMMNU (NPROC - 4)
SEMVMX 32767
SHMMAX AvailMem
SHMMNI 512
SHMSEG 120
VPS_CEILING 64

* MAXSWAPCHUNKS, SEMMAP, and VX_NCSIZE are obsolete on 11.23 PA-RISC and IPF and no longer need to be set
Set NCSIZE = (NINODE+1024)

11.31 (Itanium and PA-RISC):
The following 11.31 kernel parameters are obsolete:
maxswapchunks, msgmap, ncallout, semmap, and vx_ncsize,Nfile,Msgseg

KSI_ALLOC_MAX (NPROC*8)
MAX_THREAD_PROC 256
MAXDSIZ 1073741824 bytes
MAXDSIZ_64BIT 2147483648 bytes
MAXSSIZ 134217728 bytes
MAXSSIZ_64BIT 1073741824
MAXSWAPCHUNKS 16384*
MAXUPRC ((NPROC*9)/10)+1 Bug 6995956
MSGMAP (2+MSGMNI)
MSGMNI (NPROC)
MSGSEG 32767
MSGTQL (NPROC)
NCSIZE (NINODE+VX_NCSIZE)*
NFILE (15*NPROC+2048)
NFLOCKS (NPROC)
NINODE (8*NPROC+2048)
NKTHREAD (((NPROC*7)/4)+16)
NPROC 4096
SEMMAP (SEMMNI+2)*
SEMMNI (NPROC)
SEMMNS (SEMMNI*2)
SEMMNU (NPROC - 4)
SEMVMX 32768
SHMMAX AvailMem
SHMMNI 512
SHMSEG 120
VPS_CEILING 64

* MAXSWAPCHUNKS, SEMMAP, and VX_NCSIZE are obsolete on 11.23 PA-RISC and IPF and no longer need to be set
Set NCSIZE = (NINODE+1024)

11.31 (Itanium and PA-RISC):
The following 11.31 kernel parameters are obsolete:
maxswapchunks, msgmap, ncallout, semmap,vx_ncsize,Nfile and Msgseg

KSI_ALLOC_MAX (NPROC*8)
MAX_THREAD_PROC 256
MAXDSIZ 1073741824 bytes
MAXDSIZ_64BIT 2147483648 bytes
MAXSSIZ 134217728 bytes
MAXSSIZ_64BIT 1073741824
MAXSWAPCHUNKS 16384*
MAXUPRC ((NPROC*9)/10)
MSGMAP (MSGTQL+2)
MSGMNI (NPROC)
MSGSEG 32767
MSGTQL (NPROC)
NCALLOUT (NKTHREAD+16)*
NCSIZE ((8*NPROC+2048)+VX_NCSIZE)*
NFILE (15*NPROC+2048)
NFLOCKS (NPROC)
NINODE (8*NPROC+2048)
NKTHREAD (((NPROC*7)/4)+16)
NPROC 4096
SEMMAP (SEMMNI+2)*
SEMMNI (NPROC)
SEMMNS (SEMMNI*2)
SEMMNU (NPROC - 4)
SEMVMX 32768
SHMMAX AvailMem
~~SHMMIN 1~~
SHMMNI 512
SHMSEG 32
VPS_CEILING 64

* MAXSWAPCHUNKS, SEMMAP, NCALLOUT, and VX_NCSIZE are obsolete on 11.23 PA-RISC and IPF and no longer need to be set
Set NCSIZE = (NINODE+1024)

11.31 (Itanium and PA-RISC):
The following 11.31 kernel parameters are obsolete:
maxswapchunks, msgmap, ncallout, semmap,vx_ncsize,Nfile and Msgseg

SHMMAX AvailMem
~~SHMMIN 1~~
SHMMNI 512
SHMSEG 32
SEMMNI 8192
SEMMNS 16384

MAXDSIZ
1073741824 bytes

MAXDSIZ_64BIT
2147483648 bytes

MAXSSIZ
134217728 bytes

MAXSSIZ_64BIT
1073741824

SHMMAX 1GB
~~SHMMIN 1~~
SHMMNI 100
SHMSEG 10
SEMMNI 70
SEMMNS 200

nflocks = 200 + sum of the values of init.ora parameter db_filesfor all instances of oracle onthe machine.

MAX_THREAD_PROC = 256 or more

maxdsiz
1Gb (1073741824) 0x40000000

maxdsiz_64bit
1.6Gb (1717986918) 66666666

maxssiz
200mb (209715200) C800000

maxssiz_64bit
200mb (209715200) C800000

maxtsiz
1Gb (1073741824) 0x40000000

maxtsiz_64bit
1Gb (1073741824) 0x40000000

SHMMAX 1GB
~~SHMMIN 1~~
SHMMNI 100
SHMSEG 10
SEMMNI 70
SEMMNS 200
maxdsiz and maxdsiz_64bit must be >= 128Mb

SHMMAX 1GB
~~SHMMIN 1~~
SHMMNI 100
SHMSEG 10
SEMMNI 70
SEMMNS 200

maxdsiz and maxdsiz_64bit must be >= 128Mb

Oracle Version 11.2 11.1 10.2 10.1 9.2.0 9.0.1 8.1.7 8.1.6 8.1.5 8.0.6 8.0.5

Oracle Solaris
(32-bit and 64-bit stands for Oracle DB, not OS)

Solaris(64bit) 10 (update 6 or higher), Solaris 11

NOTE: On Solaris 11, only 11.2.0.3 is certified (not 11.2.0.1 or 11.2.0.2)

Set the following variable before installing 11.2.0.3 on Solaris 11:
export AWT_TOOLKIT=XToolkit

2.9 Update 7 (09/04), 2.10

2.8 Update 7 (02/02), 2.9 Update 6 (04/04), 2.10 (64bit)
Solaris 10 on AMD64/x86_64

Solaris SPARC 2.8, 2.9 (64bit)
o Solaris SPARC 10 (64bit) requires 10.1.0.3.0 patchset
o Solaris x86 2.9, 10

o 2.6, 2.7, 2.8, 2.9 (32bit)
o Solaris 10 (32bit) requires 9.2.0.4.0 patchset
o 2.8, 2.9 (64bit)
o Solaris 10 (64bit) requires 9.2.0.5.0 patchset

o 2.6, 2.7, 2.8, 2.9 (32bit)
o 2.8, 2.9 (64bit)

o 2.6, 2.7, 2.8 (32bit)
o 2.7, 2.8 (64bit)

2.6, 2.7, 2.8 (32bit)
o 2.7 (64bit)

2.5.1, 2.6, 2.7, 2.8

Solaris Disk Space 1.5 to 2G Database
4.7G Software 1.5 to 2G Database
4.7G Software 1.2G Database
1.5G - 3.5G Software
1G Companion
150M-1G Client 1.2G Database
1.5G Software
1G Companion
150M-1G Client 4.5G 3.5G (32bit)
5.7G (64bit) 1355Mb 1170Mb 811Mb 600Mb 600Mb

Solaris RAM

Database: minimum 1GB, recommended 2GB

Grid Infrastructure for standalone server: minimum 1.5GB (plus another 1GB if installing Database too), recommended 4GB

1GB

512Mb
256Mb(Client/Compan)

512Mb

256Mb (32bit)
512Mb (64bit)

128Mb

64Mb or
128Mb /
ConText

32Mb or
128Mb /
ConText

Solaris swap If RAM = 1 GB to 2 GB
then 1.5 times RAM
elseif RAM = 2 GB and 16 GB
then match RAM
else RAM > 16 GB
then 16 GB

Note: On Oracle Solaris, if you use non-swappable memory, such as ISM, then you should deduct the memory allocated to this space from the available RAM before calculating swap space. If you plan to install Oracle Database or Oracle RAC on systems using DISM, then available swap space must be at least equal to the sum of the SGA sizes of all instances running on the servers. If RAM = 1024MB to 2048Mb
then 1.5 times RAM
elseif RAM > 2048MB and < 8192MB
then match RAM
else RAM > 8192MB
then .75 times RAM If RAM = 1024MB to 2048Mb
then 1.5 times RAM
elseif RAM > 2048MB and < 8192MB
then match RAM
else RAM > 8192MB
then .75 times RAM 1Gb or match RAM
512Mb(Client/Compan) 1Gb or match RAM 400Mb 2*RAM or
400Mb 2*RAM or
400Mb 2*RAM 3*RAM 3*RAM

Solaris tmp 1GB 275Mb 400Mb 400Mb 400Mb 400Mb ? ? ? 20Mb 20Mb

Solaris JDK & JRE JDK 6 Update 10 (Java SE Development Kit 1.6 u10) or JDK 5 (1.5.0_16) JDK 1.5.0_11 is installed JDK 1.4.2_01 is installed
JDK 1.4.2_08 is installed (x86_64) JDK 1.4.2_01 is installed JDK 1.3.1_02 & 1.1.8_12 (32bit) 1.1.8_15 (64bit) JDK 1.2.2_07 & 1.1.8_12 JDK 1.2.2. & 1.1.8_10 1.1.8_10 ? n/a n/a

Solaris Patches/
Packages

Required packages Solaris 10:
SUNWarc
SUNWbtool
SUNWhea
SUNWlibC
SUNWlibm
SUNWlibms
~~SUNWmfrun~~
SUNWsprot
SUNWtoo
SUNWi1of
SUNWi1cs (ISO8859-1)
SUNWi15cs (ISO8859-15)
SUNWxwfnt
SUNWcsl

Although it is not listed in the Install Guide, the RAC root.sh script requires /usr/xpg4/bin/tr and so requires the SUNWxcu4 package.
@ See Bug:14046807 for confirmation.

The 11.2 install guide doesn't list any required packages for Solaris 11, but the above list (including SUNWxcu4) can be used as a guideline

Important: For non-sun4u or sun4v workstations Only, seeNote 467166.1:
set the following before starting the OUI,DBCA, or DBUA:
$ export JAVA64FLAG="-d64"

Required Packages:
SUNWarc
SUNWbtool
SUNWhea
SUNWi15cs
SUNWi1cs
SUNWi1of
SUNWlibC
SUNWlibm
SUNWlibms
SUNWmfrun
SUNWsprot
SUNWsprox (Not applicable to Solaris 10),
SUNWtoo
SUNWxwfnt
SUNWuiu8 Note 290034.1
SUNWulcf Note 290034.1

Although it is not listed in the Install Guide, the RAC root.sh script requires /usr/xpg4/bin/tr and so requires the SUNWxcu4 package.
@ See Bug:14046807 for confirmation.

Solaris 9 Reqd Patches:
112233-11
111722-04
112874-39
115675-01 (NUMA only)
113471-08 (NUMA only)
115675-01 (NUMA only)
113029-07 for Fair Share Scheduler, See Note 558374.1

Solaris 10 Reqd Patches:
127111-02 s/b 127127-11
137111-04 s/b 137137-09 (Part Number B32314-02)

To support Pro*C/C++,Pro*FORTRAN,Oracle Call Interface,Oracle C++ Call Interface,Oracle XML Developers Kit (XDK)
112760-05 (Solaris 9)
117837-05 (Solaris X86 10)
117846-08 (Solaris X86 10)
118682-01 (Solaris X86 10)
ulimit(TIME) to unlimited. Refer to Note 250262.1
ulimit(FILE) to unlimited. Refer to Note 250262.1
ulimit(DATA) to a minimum of 1048576. Refer to Note 250262.1
ulimit(STACK) to a minimum of 32768. Refer to Note 250262.1
ulimit(NOFILES) to a minimum of 4096. Refer to Note 250262.1
ulimit(VMEMORY) to a minimum of 4194304. Refer to Note 250262.1

Required Packages:
SUNWarc,
SUNWbtool,
SUNWhea,
SUNWlibm,
SUNWlibms,
SUNWmfrun,
SUNWsprot,
SUNWsprox (Not applicable to Solaris 10),
SUNWtoo,
SUNWxwfnt,
SUNWi1cs,
SUNWi15cs,
SUNWi1of,
SUNWxcu4,
SUNWuiu8 and SUNWulcf - See Note 290034.1

Solaris 8 Reqd Patches:
108528-23
108652-66
108773-18
108921-16
108940-53
108987-13
108989-02
108993-45
109147-24
110386-03
111023-02
111111-03
111308-03
111310-01
112396-02
111721-04
112003-03
112138-01
112760-05 (Native PL/SQL,ProC,ProFortran,OCI,OCCI,XDK only)
SUNWctplx/ SUNWdtbax/ SUNWtltkx/ SUNWtoox/ SUNWxwicx/ SUNWxwplx/
and also Patch 108940-76 (or higher) in order to fix the SUNWdtbax package Note 366100.1

Solaris 9 Reqd Patches:
112233-11
111722-04 (Bug 4122475)
115675-01
113471-08
115675-01
112760-05 (Native PL/SQL,ProC,ProFortran,OCI,OCCI,XDK only)
112963-25
113029-07 for Fair Scheduler, See Note 558374.1

Solaris 10 Reqd Patches
127111-02 s/b 127127-11 for 10.2.0.4 or later (see README for 10.2.0.4.0)
127111-03 s/b 127127-11 See Note 460424.1

Solaris 10 x86_64 Reqd Patches:
118345-03
119961-01
127127-11 See Note 460424.1

Solaris 10 special instructions:
Select 'Do not create a starter database' when installing Oracle 10gR2 due to Bug 4884705 and run the DBCA after the installation.

The Fair Share Scheduler(FSS) requires Solaris 10 11/06 or higher.
If using a prior update of Solaris 10 install the following patches :
Install patch 118833-36 before installing Oracle 10gR2 for Solaris 10 on SPARC.
Install patch 118855-36 before installing Oracle 10gR2 for Solaris 10 on x86-64

IMPORTANT: Patch 4589082 needs to be installed prior to attempting an installation of 10.2 on Solaris 10 SPARC to avoid "Error in invoking target 'relink' of makefile 'precomp/lib/ins_precomp.mk' related to -ldce not found. See also Note 333348.1.

IMPORTANT: See Note 1190843.1 regarding a related relinking issue in 10.2.0.5

Required Packages:
SUNWarc,
SUNWbtool,
SUNWhea,
SUNWlibC (CRS only)
SUNWlibm,
SUNWlibms,
SUNWmfrun,
SUNWsprot,
SUNWsprox (Not applicable to Solaris 10),
SUNWtoo,
SUNWxwfnt,
SUNWi1cs,
SUNWi15cs,
SUNWi1of
SUNWuiu8,SUNWulcf (if Bug 4025250 occurs)
SUNWxcu4

Solaris 8 Reqd Patches:
108528-23
108652-66
108773-18
108921-16
108940-53
108987-13
108989-02
108993-18
109147-24
110386-03
111023-02
111111-03
111308-03
111310-01
112396-02
111721-04
112003-03
112138-01

Solaris 9 Reqd Patches:
112233-11
111722-04 (Bug 4122475)
112963-25
113029-07 for Fair Scheduler, See Note 558374.1

Solaris 10 special instructions:
1. Execute runInstaller with the -ignoreSysPrereqs option.
2. Select 'Do not create a starter database' when installing Oracle 10g.
3. During installation, the warning message 'SUNWsprox package not installed' can be ignored as it is no longer provided separately. Press Continue to resume the installation.
4. Download and install PSR 10.1.0.4Patch 4163362(or apply PSR 10.1.0.3 Patch 3761843 and interim Patch 4163208 (SPARC) or patch 4186426 (x86) from support.oracle.com.
5. Download and install Patch 4365826from 10.1.0.3 or 10.1.0.4 from support.oracle.com. (SPARC only), also a merge patch containing 4365826 can be applied to 10.1.0.4.2 Patch 4590858
6. If you have an End User Solaris 10 distribution, install the SUNWuiu8 package prior to installing the 10g client.
7. The Fair Share Scheduler(FSS) requires Solaris 10 11/06 or higher.
If using a prior update of Solaris 10 install the following patches :
Install patch 118833-36 before installing Oracle 10gR2 for Solaris 10 on SPARC.
Install patch 118855-36 before installing Oracle 10gR2 for Solaris 10 on x86-64
8. Oracle Solaris 10 install Sun patch 127111-03 (SPARC) / 127127-11 (x86-64) See Note 460424.1

32bit/64bit
SUNWarc,
SUNWbtool,
SUNWhea,
SUNWlibm,
SUNWlibms,
SUNWmfrun,
SUNWsprot,
SUNWtoo
SUNWi1of and SUNWxwfnt (for Java)
SUNWsprox (for 64bit Oracle) (Not applicable to Solaris 10)
SUNWuiu8,SUNWulcf (if Bug 4025250 occurs)
SUNWxcu4

108528-05 (2.8)

Solaris 10 special instructions:
Execute runInstaller with the -ignoreSysPrereqs option
The Fair Share Scheduler(FSS) requires Solaris 10 11/06 or higher.
If using a prior update of Solaris 10 install the following patches :
Install patch 118833-36 before installing Oracle 10gR2 for Solaris 10 on SPARC.
Install patch 118855-36 before installing Oracle 10gR2 for Solaris 10 on x86-64
Oracle Solaris 10 install Sun patch 127111-03 (SPARC) / 127127-11 (x86-64) See Note 460424.1

32bit/64bit
SUNWarc,
SUNWbtool,
SUNWhea,
SUNWlibm,
SUNWlibms,
SUNWsprot,
SUNWtoo
SUNWxcu4

Additional
64bit
SUNWarcx,
SUNW2x (believe this is a typo and should be SUNWtoox)

108528-01 (2.8)
105181-15 (2.6)

SUNWarc,
SUNWbtool,
SUNWhea,
SUNWlibm, SUNWlibms, SUNWsprot,
SUNWtoo
SUNWxcu4

2.6 requires at least 105181-15

SUNWarc,
SUNWbtool,
SUNWhea,
SUNWlibm, SUNWlibms, SUNWsprot,
SUNWtoo

2.6 requires at least 105181-15

SUNWarc,
SUNWbtool, SUNWlibm, SUNWlibms,SUNWsprot,
SUNWtoo,
SUNWhea.

Sun 2.6 requires 105181-06

Solaris Kernel Settings

Refer to the 11g Solaris Install Guide. Part Number E24346-02 for steps to do this.
Verifying UDP and TCP Kernel Parameters

SEMMNI 100
SEMMNS 1024(Obsolete)
SEMMSL 256
SEMVMX 32767(Obsolete)
SHMMAX 4294967295
SHMMNI 100 (Obsolete)
NOEXEC_USER_STACK 1
Note: For Solaris 10 Oracle recommends still setting all these values in the /etc/system file, as well as, the Resource Control Facility.
Refer to the 11g Solaris Install Guide for steps to do this.

Here are the new names of the kernel parameters for Solaris 10 (Solaris 9 equivalents are in parentheses):

project.max-sem-ids 100 (semmni)

process.max-sem-nsems 256 (semmsl)

project.max-shm-memory 4294967295 (shmmax)

project.max-shm-ids 100 (shmmni)

SEMMNI 100 ***
SEMMNS 1024 **
SEMMSL 256 ***
SEMVMX 32767 **
SHMMAX 4294967295
SHMMIN 1 *
SHMMNI 100***
SHMSEG 10 *
NOEXEC_USER_STACK 1
* obsolete in Solaris 9 and 10
** obsolete in Solaris 10
*** default value in Solaris 10 is already larger
Note: for Solaris 10 SHMMAX which is now set through the Resource Control Facility not /etc/system. Refer to the 10gR2 for Solaris SPARC Installation guide for steps to do this, as well as, the Release Notes which has corrections:
10.2 Install Guides and Release Notes

Here are the new names of the kernel parameters for Solaris 10 (Solaris 9 equivalents are in parentheses):

project.max-sem-ids 100 (semmni)

process.max-sem-nsems 256 (semmsl)

project.max-shm-memory 4294967295 (shmmax)

project.max-shm-ids 100 (shmmni)

SEMMNI 100 ***
SEMMNS 1024 **
SEMMSL 256 ***
SHMMAX 4294967295
SHMMIN 1 *
SHMMNI 100***
SHMSEG 10 *
NOEXEC_USER_STACK 1
* obsolete in Solaris 9 and 10
** obsolete in Solaris 10
*** default value in Solaris 10 is already larger

SEMMNI 100
SEMMNS 256
SEMMSL 256
SHMMAX 4294967295
SHMMIN 1
SHMMNI 100
SHMSEG 10

SHMMAX 4294967295
SHMMIN 1
SHMMNI 100
SHMSEG 10
SEMMNI 100
SEMMSL Set to 10 plus the largest PROCESSES parameter of any Oracle database on the system.
SEMMNS Set to the sum of the PROCESSES parameter for each Oracle database, adding the largest one twice, then add an additional 10 for each database.
SEMOPM 100
SEMVMX 32767

SHMMAX 0.5*(physical memory present in machine)
SHMMIN 1
SHMMNI 100
SHMSEG 10
SEMMNI 100
SEMMSL Set to 10 plus the largest initsid.ora PROCESSES parameter of an Oracle database on the system.
SEMMNS Set to the sum of the PROCESSES parameter for each Oracle database except the largest one, plus 2 times the largest PROCESSES value, plus 10 times the number of Oracle databases.
SEMOPM 100
SEMVMX 32767

SHMMAX 4294967295
SHMMIN 1
SHMMNI 100
SHMSEG 10
SEMMNS 200
SEMMNI 70
SEMMSL Equal to or greater than the value of the
PROCESSES initialization parameter.

Oracle Version 11.2 11.1 10.2 10.1 9.2.0 9.0.1 8.1.7 8.1.6 8.1.5 8.0.6 8.0.5

Tru64 OS
do "/usr/sbin/sizer -v" to see specific version of Tru64, "uname -a" will not show it. NA Not Available 5.1b 5.1b 5.1a, 5.1b 5.0a, 5.1, 5.1a, 5.1b 4.0D-G, 5.0, 5.0a, 5.1, 5.1a, 5.1b(EV5.6 processor or higher) do '/usr/sbin/psrinfo -v' 4.0D-G, 5.0, 5.0a, 5.1 4.0D-G, 5.0, 5.0a, 5.1 4.0D-G, 5.0, 5.0a, 5.1, 5.1a 4.0D-G, 5.0, 5.0a

Tru64 Disk Space NA Not Available 1.2G Database
3G Software
1G Companion
150M-1.9G Client 1.2G Database
3G Software
1G Companion
150M-1.9G Client 4.5G 4.7G 1.5G 1.2G 811Mb 800Mb 800Mb

Tru64 RAM NA Not Available 1Gb
256Mb (Client/Compan) 512Mb
256Mb(Client/Compan) 512Mb 256Mb 128Mb 128Mb 128Mb 128Mb 128Mb

Tru64 swap NA Not Available 2Gb or match RAM
512Mb(Client/Compan) 1Gb or match RAM
512Mb(Client/Compan) 1Gb or match RAM 400Mb 400Mb 400Mb 2-4*RAM 2-4*RAM 2-4*RAM

Tru64 tmp NA Not Available 400Mb 400Mb 400Mb 400Mb 75Mb ? 75Mb 40Mb 40Mb

Tru64 JDK & JRE NA Not Available SDK 1.4.2 needs to be installed
download here SDK 1.4.2 needs to be installed
download here JDK 1.3.1.03 & 1.1.8-10 JDK 1.2.2-8 & 1.1.8-10 JDK 1.2.2. & 1.1.8-7 1.1.8 ? n/a n/a

Tru64 Patches/
Packages

Not Available

OSFCMPLRS
OSFLIBA
OSFPGMR
OSFSER
OSFX11

5.1B-3 (patchkit 5): T64V51BB26AS0005-20050502

OSFSER
OSFLIBA
OSFPGMR
OSFCMPLRS
OSFX11
OSFXDEVX (Spatial only)
OSFXINCLUDE (Spatial only)
OSFXLIBA (Spatial only)

5.1B-3 (patchkit 5): T64V51BB26AS0005-20050502

OSFSER
OSFLIBA
OSFPGMR
OSFCMPLRS
OSFX11

o 5.1a with patchkit 6 or higher required:
T64V51AB24AS0006-20031031
o HP Tru64 UNIX Performance improvement to times(3) system call:
T64KIT0023583-V51AB24-E-20040913
o HP Tru64 UNIX V5.1A PK6 (BL24) ERP Kit - file region locks can be inadvertently released as a result of AIO processing:
T64KIT0023109-V51AB24-E-20040729

o 5.1B-3 (patchkit 5): T64V51BB26AS0005-20050502

OSFSER
OSFLIBA
OSFPGMR
OSFCMPLRS
OSFX11

5.0a
patchkit 2 and bugfix HPAQ217F3 or
patchkit 3 and bugfix HPAQ217F3 or
patchkit 4

5.1
patchkit 5 with T64V5117_C0038300
_unique_id_and_mfg_date.tar T64V51B19-C0125001-14319-E-20020516.tar (C1250.01 PatchId), T64V51B19-C0151600-15736-E-20021017.tar (C1516.00 PatchId).Go to here to download

5.1a
patchkit 4 with T64V51AB3-C0074700-15747-E-20021018.tar (C747.00 PatchId). Go to here to download

5.1b = Patchkit 2 or greater, apply patch 01414.00 (included in Pk3) to address Note 261309.1 ld seg fault = Patchkit 2 or greater

The following additional 5.1b O/S patch is also required, please obtain from HP: T64KIT0021686-V51BB24-E-20040223 -- File Locking issue

OSFLIBA,
OSFPGMR,
OSFCMPLRS

4.0D = Patchkit 4 or greater

4.0E = Patchkit 2 or greater

4.0F = Patchkit 1 or greater

5.1 = Patchkit 5 or greater with T64V51B19-C0125001-14319-E-20020516.tar (C1250.01 PatchId) and T64V51B19-C0151600-15736-E-20021017.tar (C1516.00 PatchId). .Go tohere to download

5.1a = Patchkit 3 or greater with T64V51AB3-C0074700-15747-E-20021018.tar (C747.00 PatchId). Go to here to download

5.1b = Patchkit 2 or greater, apply patch 01414.00 (included in Pk3) to address Note 261309.1 ld seg fault

The following additional 5.1b O/S patch is also required, please obtain from HP: T64KIT0021686-V51BB24-E-20040223 -- File Locking issue

OSFLIBA,
OSFPGMR,
OSFCMPLRS

4.0D = Patchkit 4 or greater

4.0E = Patchkit 2 or greater

4.0F = Patchkit 1 or greater

OSFLIBA,
OSFPGMR,
OSFCMPLRS

OSFLIBA, OSFPGMR, OSFCMPLRS

Tru64 Kernel Settings

Not Available

PER_PROC_STACK_SIZE ~~8388608~~ 33554432 to avoid ORA-4030s (Install Guide recommends 8388608)
MAX_PER_PROC_STACK_SIZE 33554432
PER_PROC_DATA_SIZE 335544320 or RAM (whichever is greater)
MAX_PER_PROC_DATA_SIZE 335544320 or RAM (whichever is greater)
PER_PROC_ADDRESS_SPACE 1073741824 or RAM (whichever is greater)
MAX_PER_PROC_ADDRESS_SPACE 1073741824 or RAM (whichever is greater)
SHM_MAX 4278190080 (4 GB less 16MB)
SHM_MIN 1
SHM_MNI 256
SHM_SEG 256
NEW_WIRE_METHOD 1 (if >= 5.1b PK3 and patch T64KIT0021686-V51BB24-E-20040223)Note 272697.1
for 5.1b PK5 and higher is defaulter to 1 and can no longer be changed
NEW_WIRE_METHOD 0 (if <= 5.1b PK2) Note 272697.1
VM_BIGPG_ENABLED 0
FIFO_DO_ADAPTIVE 0
SSM_THRESHOLD *
MSG_SIZE 32768
MAX_OBJS 5120
MAX_ASYNC_REQ 256
MAX_SESSIONS 500
RDG_MAX_AUTO_MSG_WIRES 0
RDG_AUTO_MSG_WIRES 0
AIO_TASK_MAX_NUM 8193
EXEC_DISABLE_ARG_LIMIT 1

* Set this attribute to 0 only if the rad_gh_regions[n] or gh_chunks attributes are set in the vm subsystem. Otherwise, do not change the value.

PER_PROC_STACK_SIZE ~~8388608~~ 33554432 to avoid ORA-4030s (Install Guide recommends 8388608)
MAX_PER_PROC_STACK_SIZE 33554432
PER_PROC_DATA_SIZE 335544320
MAX_PER_PROC_DATA_SIZE 335544320
PER_PROC_ADDRESS_SPACE 1073741824 or RAM (whichever is greater)
MAX_PER_PROC_ADDRESS_SPACE 1073741824 or RAM (whichever is greater)
SHM_MAX 4278190080 (4 GB less 16MB)
SHM_MIN 1
SHM_MNI 256
SHM_SEG 256
NEW_WIRE_METHOD 1 (if >= 5.1b PK3 and patch T64KIT0021686-V51BB24-E-20040223)Note 272697.1
for 5.1b PK5 and higher is defaulter to 1 and can no longer be changed
NEW_WIRE_METHOD 0 (if <= 5.1b PK2) Note 272697.1
VM_BIGPG_ENABLED 0
FIFO_DO_ADAPTIVE 0
SSM_THRESHOLD *
MSG_SIZE 32768
MAX_OBJS 5120
MAX_ASYNC_REQ 256
MAX_SESSIONS 500
RDG_MAX_AUTO_MSG_WIRES 0
RDG_AUTO_MSG_WIRES 0
AIO_TASK_MAX_NUM 8193

* Set this attribute to 0 only if the rad_gh_regions[n] or gh_chunks attributes are set in the vm subsystem. Otherwise, do not change the value.

MAX_PER_PROC_STACK_SIZE 33554432
PER_PROC_STACK_SIZE ~~8388608~~ 33554432 to avoid ORA-4030s (Install Guide recommends 8388608)
PER_PROC_DATA_SIZE 201326592
SHM_MAX 4278190080 (4 GB less 16MB)
SHM_MIN 1
SHM_MNI 256
SHM_SEG 128
NEW_WIRE_METHOD 1 (if >= 5.1b PK3 and patch T64KIT0021686-V51BB24-E-20040223 or 5.1a PK6)Note 272697.1
for 5.1b PK5 and higher is defaulter to 1 and can no longer be changed
NEW_WIRE_METHOD 0 (if <= 5.1b PK2) Note 272697.1
VM_BIGPG_ENABLED 0
FIFO_DO_ADAPTIVE 0

Alpha processor EV5.6 or later

PER_PROC_STACK_SIZE 33554432
MAX_PER_PROC_STACK_SIZE 536870912
PER_PROC_DATA_SIZE RAM
MAX_PER_PROC_DATA_SIZE RAM
PER_PROC_ADDRESS_SIZE RAM
MAX_PER_PROC_ADDRESS_SIZE RAM
SHM_MAX 4278190080 (4 GB less 16MB)
SHM_MIN 1
SHM_MNI 256
SHM_SEG 128
NEW_WIRE_METHOD 1 (if >= 5.1b PK3 and patch T64KIT0021686-V51BB24-E-20040223) Note 272697.1
for 5.1b PK5 and higher is defaulter to 1 and can no longer be changed
NEW_WIRE_METHOD 0 (if <= 5.1b PK2) Note 272697.1
FIFO_DO_ADAPTIVE 0

Alpha processor EV5.6 or later

SHMMAX 2139095040(2GB-8MB)
SHMMIN 1
SHMMNI 100
SHMSEG 32
NEW_WIRE_METHOD 1 (if >= 5.1b PK3 and patch T64KIT0021686-V51BB24-E-20040223) Note 272697.1
for 5.1b PK5 and higher is defaulter to 1 and can no longer be changed
NEW_WIRE_METHOD 0 (if <= 5.1b PK2)Note 272697.1
FIFO_DO_ADAPTIVE 0

vm-mapentries=1024 in the /etc/sysconfigtab, verify with '/sbin/sysconfig -q vm' - applies to OS versions below 5.0, starting in 5.0 it is autoset

Alpha processor EV5.6 or later

SHMMAX 2139095040(2GB-8MB)
SHMMIN 1
SHMMNI 100
SHMSEG 32

SHMMAX 8388608 or higher than the maximum SGA size.
Note: If anticipated SGA size is greater than 2 GB, set it to 2 GB - 8 MB; otherwise, round the SGA sizeup to the next 8 MB and set that to SHMMAX.
SHMMIN 1
SHMMNI 100
SHMSEG 32

SHMMAX
2139095040 (2 GB-8 MB)
SHMMIN 1
SHMMNI 100
SHMSEG 32

SHMMAX 8388608 or higher than the maximum SGA size.
Note: If anticipated SGA size is greater than 2 GB, set it to 2 GB - 8 MB; otherwise, round the SGA size up to the next 8 MB and set
that to SHMMAX.
SHMMIN 1
SHMMNI 100
SHMSEG 32

Oracle Version 11.2 11.1 10.2 10.1 9.2.0 9.0.1 8.1.7 8.1.6 8.1.5 8.0.6 8.0.5

Linux x86 OS
(See Note 225710.1 for supported kernels) andNote 265262.1for "Things to know about Linux" o RHEL4,OEL4 - Update 7 or greater which is Kernel 2.6.9-78 or newer
o RHEL5, OEL5 - 5.2 or greater which is Kernel 2.6.18-92 or newer
o SLES10 - Kernel 2.6.16.21 or higher
o SLES 11 - Kernel 2.6.27.19-5 or greater
o Asianux Server 3 SP2 o RHEL4, OEL4, Asianux 2.0
2.6.9
o RHEL5, OEL5, Asianux Server 3
2.6.18
o SuSE SLES10
2.6.16.21
o SuSE SLES11 - Kernel 2.6.27.19-5 or greater o RHEL 3 AS/ES ( RHEL3 ) (Update 4 or later)
2.4.21-27.EL or higher
o RHEL 4 AS/ES ( RHEL4 ) and Oracle Enterprise Linux 4 ( OEL4 )
2.6.9-5.0.5.EL or higher
o RHEL 5 AS/ES ( RHEL5 ) and Oracle Enterprise Linux 5 ( OEL5 )
2.6.18-8 or higher
o SuSE SLES9
2.6.5-7.201 or higher
o SuSE SLES10
o SuSE SLES11 - Kernel 2.6.27.19-5 or greater
o Asianux 1.0
2.4.21-27.EL or higher
o Asianux 2.0
2.6.9-5.0.5.EL or higher o RHEL AS/ES 2.1 (Update 3 or higher)
2.4.9-e34 or higher
o RHEL AS/ES 3.0 (Update 2 or higher)
2.4.21-15.EL or higher
o RHEL4 (10.1.0.3.0 patchset required)
refer to 10.1.0.3.0 Release Notes
o SuSE SLES8 (Service Pack 3 or higher)
2.4.21-138
o SuSE SLES9
2.6.5-7.5
o Red Flag Advanced Server 4.0 (China only)
o Miracle Linux Std Ed 2.1 (Japan only)
o Asianux 1.0 o Red Hat Enterprise AS/ES 2.1
2.4.9-e34 or higher
o Red Hat Enterprise AS/ES 3.0
2.4.21-15
o RHEL4 (9.2.0.6.0 patchset required or 9.2.0.5.0 patchset and Patch 4276910 required)
refer to 9.2.0.4 Release Notes
o SuSE SLES8
2.4.21-138
o SuSE SLES9
2.6.5-7.97
o United Linux 1.0 (SP3 or higher)
o Red Flag DC Server 4.0 (China and Hong Kong only)
o Monta Vista Carrier Grade Linux 3.0 (embedded)
o Miracle Linux Std Ed 2.1 (Japan only)
2.4.7
o Asianux 1.0 Caldera OU8+LKP, Red Hat 7.1, Advanced Server 2.1, SuSE 7.1, 7.2, SLES7, Kernel 2.4.4 Caldera OU8+LKP, Miracle 1.0, 2.0, Red Hat 6.1,6.2, EE 6.2, 7.0, 7.1, Advanced Server 2.1, SuSE 7.0, 7.1, 7.2, SLES7, Kernel 2.2.16 Miracle 1.0, Red Hat 6.0,6.1,6.2, EE 6.2, SuSE 6.3, 6.4, 7.0, VA 6.2, Kernel 2.2 Red Hat 6.2, EE 6.2, SuSE 6.3, 6.4, Kernel 2.2 Red Hat 6.2, SuSE 6.4, 7.0, Kernel 2.0.34 2.0.34

Linux x86 Disk Space 3.8G Database 2G Database
3.5G Install 1.2G Database
1.5 to 3.5G Install 1.2G Database
1.5G Software
1G Companion
150M-650M Client 4.5G 3.5G 900Mb 1G 811Mb 400Mb 400Mb

Linux x86 RAM 1GB 1GB 1GB 512Mb
256Mb(Client/Compan) 512Mb 512Mb 128Mb 128Mb 128Mb 32Mb 32Mb

Linux x86 swap If RAM=1 GB to 2 GB then 1.5 times RAM
If RAM=2 GB to 16 GB then equal to RAM
If greater than 16 GB then 16 GB If RAM between 1 GB and 2 GB
then 1.5 times RAM
elseif RAM between 2 GB and 16 GB
then match RAM
else RAM > 16 GB
then 16 GB If RAM = 1024MB to 2048Mb
then 1.5 times RAM
elseif RAM > 2048MB and < 8192MB
then match RAM
else RAM > 8192MB
then .75 times RAM 1Gb or match RAM
512Mb(Client/Compan) 1Gb or match RAM 512Mb 400Mb 400Mb 256Mb 3*RAM 3*RAM

Linux x86 tmp 1024Mb 400Mb 400Mb 400Mb 400Mb 400Mb 75Mb 75Mb 75Mb 75Mb 20Mb

Linux x86 JDK & JRE JDK (version TBS) is installed JDK (version TBS) is installed JDK 1.4.2_08 is installed JDK 1.4.2_02 is installed Sun JDK 1.3.1_02 & Blackdown 1.1.8_v3 Blackdown JDK 1.1.8_3 & 1.1.8_v3 JDK 1.2.2. & 1.1.8-3from IBM 1.1.8 1.1.6v5 n/a n/a

Linux x86 Patches/
Packages

RHEL4, OEL4:
Refer to Note 880211.1

binutils-2.15.92.0.2-25

compat-libstdc++-33-3.2.3-47.3

elfutils-libelf-0.97.1-5

glibc-2.3.4-2.41

glibc-common-2.3.4-2.41

libaio-0.3.105-2

libgcc-3.4.6-10

libstdc++-3.4.6-10

make-3.80-7.EL4

pdksh-5.2.14-30.6

unixODBC-2.2.11-1.RHEL4.1

The remaining Install Guide requirements will have to be installed:

elfutils-libelf-devel-0.97.1-5.i386.rpm

glibc-headers-2.3.4-2.41.i386.rpm

glibc-kernheaders-2.4-9.1.103.EL.i386.rpm will be required as a prerequisite

glibc-devel-2.3.4-2.41.i386.rpm

gcc-3.4.6-10.i386.rpm

libstdc++-devel-3.4.6-10.i386.rpm

gcc-c++-3.4.6-10.i386.rpm

libaio-devel-0.3.105-2.i386.rpm

sysstat-5.0.5-19.el4.i386.rpm

unixODBC-devel-2.2.11-1.RHEL4.1.i386.rpm

NOTE: If you download unixODBC from ftp://ftp.unixodbc.org/pub/unixODBC/ then the header and library files are distributed together in one gzipped tar file.

RHEL5, OEL5:
Refer to Note 880936.1

SLES10:
Refer to Note 763386.1

SLES11:
Refer to Note 881025.1

Asianux 2.0,OEL4,RHEL4:
refer to Note 430653.1

default Update 3 RPMs install or higher, see Note 376183.1

binutils-2.15.92.0.2-18 *

compat-libstdc++-33.2.3-47.3 *

elfutils-libelf-0.97-5 *

elfutils-libelf-devel-0.97-5

glibc-2.3.4-2.19 *

glibc-common-2.3.4-2.19 *

glibc-devel-2.3.4-2.19

glibc-headers-2.3.4-2.19 (glibc-devel required RPM)

glibc-kernheaders-2.4-9.1.98 (glibc-devel required RPM)

gcc-3.4.5-2

gcc-c++-3.4.5-2

libaio-0.3.105-2 *

libaio-devel-0.3.105-2

libgcc-3.4.5 *

libstdc++-3.4.5-2 *

libstdc++-devel-3.4.5-2

make-3.80-5 *

sysstat-5.0.5 *

unixODBC-2.2.11-1.RHEL4

unixODBC-devel-2.2.11-1.RHEL4
* default OS installed

NOTE: If you download unixODBC from ftp://ftp.unixodbc.org/pub/unixODBC/ then the header and library files are distributed together in one gzipped tar file.

Asianux Server 3,OEL5,RHEL5:
refer to Note 438765.1

default RPM install, see Note 376183.1

binutils-2.17.50.0.6-2.el5 *

compat-libstdc++-33-3.2.3-61

elfutils-libelf-0.125-3.el5 *

elfutils-libelf-devel-0.125-3.el5

elfutils-libelf-devel-static-0.125-3.el5
(required by elfutils-libelf-devel)

glibc-2.5-12 *

glibc-common-2.5-12 *

glibc-devel-2.5-12

glibc-headers-2.5-12
(required by glibc-devel)

gcc-4.1.1-52.el5

gcc-c++-4.1.1-52.el5

libaio-0.3.106

libaio-devel-0.3.106

libgcc-4.1.1-52

libgomp-4.1.1-52.el5
(required by gcc)

libstdc++-4.1.1-52.el5 *

libstdc++-devel-4.1.1-52.el5

make-3.81-1.1 *

sysstat-7.0.0-3.el5

unixODBC-2.2.11-7.1

unixODBC-devel-2.2.11-7.1
* default OS installed

NOTE: If you download unixODBC from ftp://ftp.unixodbc.org/pub/unixODBC/ then the header and library files are distributed together in one gzipped tar file.

SLES10:
refer to Note 452818.1

default RPM install, see Note 386391.1

binutils-2.16.91.0.5-23.4 *

compat-libstdc++-5.0.7-22.2 *

glibc-2.4-31.2 *

glibc-devel-2.4-31.2

gcc-4.1.0-28.4

gd-2.0.32-23.2
(required by sysstat)

gnuplot-4.0.0-20.2
(requried by sysstat)

ksh-93r-12.9 *

libaio-0.3.104-14.2 *

libaio-devel-0.3.104-14.2

libelf-0.8.5-47.2

libgcc-4.1.0-28.4 *

libstdc++-4.1.0-28.4 *

libstdc++-devel-4.1.0-28.4

make-3.80-202.2 *

plotutils-2.4.1-591.2
(required by sysstat)

sysstat-6.0.2-16.4

unixODBC-2.2.11-21.4

unixODBC-devel-2.2.11-21.4
* default OS installed

NOTE: If you download unixODBC from ftp://ftp.unixodbc.org/pub/unixODBC/ then the header and library files are distributed together in one gzipped tar file.

SLES11:
refer to Note 849583.1

RHEL3: default RPMS (see Note 376183.1)

gcc-3.2.3-34

glibc-2.3.2-95.20

make-3.79.1

openmotif21-2.1.30-8

compat-db-4.0.14.5

compat-gcc-7.3-2.96.128

compat-gcc-c++-7.3-2.96.128

compat-libstdc++-7.3-2.96.128

compat-libstdc++-devel-7.3-2.96.128

setarch-1.3-1

XFree86 (Spatial only)

XFree86-devel (Spatial only)

RHEL4:
refer to Note 343431.1 default RPMS (seeNote 376183.1)

binutils-2.15.92.0.2-10.EL4

compat-db-4.1.25-9

compat-libstdc++-296-2.96-132.7.2

compat-libstdc++-33-3.2.3-47.3

control-center-2.8.0-12

gcc-3.4.3-9.EL4

gcc-c++-3.4.3-9.EL4

glibc-2.3.4-2

glibc-common-2.3.4-2

gnome-libs-1.4.1.2.90-44.1

libstdc++-3.4.3-9.EL4

libstdc++-devel-3.4.3-9.EL4

make-3.80-5

pdksh-5.2.14-30

sysstat-5.0.5-1

xscreensaver-4.18-5.rhel4.2

openmotif21-2.1.30-11.RHEL4.2 (required to install Oracle demos)

libaio-0.3.102-1

[Red Hat,Oracle] Enterprise Linux 5.0
Refer to Note 419646.1

default RHEL5 RPMs (see Note 376183.1)

default OEL5 RPMs (see Note 401167.1)

gcc-c++-4.1.1-52.el5.i386.rpm and all its dependent packages.
The dependent packages are:
gcc-4.1.1-52.el5.i386.rpm
libstdc++-devel-4.1.1-52.el5.i386.rpm
glibc-devel-2.5-12.i386.rpm
glibc-headers-2.5-12.i386.rpm
libgomp-4.1.1-52.el5.i386.rpm

libXp-1.0.0-8.i386.rpm

compat-gcc-34-3.4.6-4.i386rpm

compat-gcc-c++-34-3.4.6-4.i386rpm

compat-libstdc++-33-3.2.3-61.i386.rpm

sysstat-5.0.5-1.i386.rpm (OEL5 only)

SuSE SLES9:
Refer to Note 400429.1

default-RPMs (see NOTE 386391.1)

glibc-devel-2.3.3-98.47.i586.rpm

gcc-3.3.3-43.34.i586.rpm.

libstdc++-devel-3.3.3-43.34.i586.rpm

gcc-c++-3.3.3-43.34.i586.rpm

db1-1.85-85.1.i586.rpm

orbit-0.5.17-330.1.i586.rpm

gnome-libs-1.4.1.7-671.1.i586.rpm.

plotutils-2.4.1-575.1.i586.rpm

gnuplot-3.7.3-256.1.i586.rpm

sysstat-5.0.1-35.4.i586.rpm.

SLES10:
refer to Note 387137.1

default RPM install, see Note 386391.1

glibc-devel-2.4-31.2.i586.rpm

gcc-4.1.0-28.4.i586.rpm

libstdc++-devel-4.1.0-28.4.i586.rpm

gcc-c++-4.1.0-28.4.i586.rpm

libaio-devel-0.3.104-14.2.i586.rpm

SLES11:
refer to Note 842649.1

RHEL ES/AS 2.1:

make-3.79

gcc-2.96-128

gcc-c++-2.96-128

openmotif-2.1.30-11

glibc-2.2.4-32

libstdc++-2.96-128

XFree86 (Spatial only)

XFree86-devel (Spatial only)

RHEL ES/AS 3:
Refer to Note 394360.1

default-RPMs (see NOTE 376183.1)

gcc-3.2.3-34

gcc-c++-3.2.3-34

libstdc++-devel-3.2.3.3-34

libaio-0.3.96-3.i386.rpm (required to configure Async IO)

libaio-devel-0.3.96-3.i386.rpm (required to configure Async IO)

XFree86 (Spatial only)

XFree86-devel (Spatial only)

set LD_ASSUME_KERNEL=2.4.19

RHEL4:
Refer to Note 392940.1
Patch 4153257 required for installer to work

default RPMS (see Note 376183.1)

binutils-2.15.92.0.2-10.EL4

compat-db-4.1.25-9

compat-libstdc++-296-2.96-132.7.2

compat-libstdc++-33-3.2.3-47.3

control-center-2.8.0-12

gcc-3.4.3-9.EL4

gcc-c++-3.4.3-9.EL4

glibc-2.3.4-2

glibc-common-2.3.4-2

gnome-libs-1.4.1.2.90-44.1

libstdc++-3.4.3-9.EL4

libstdc++-devel-3.4.3-9.EL4

make-3.80-5

pdksh-5.2.14-30

sysstat-5.0.5-1

xscreensaver-4.18-5.rhel4.2

openmotif21-2.1.30-11.RHEL4.2 (required to install Oracle demos)

libaio-0.3.96

SuSE SLES8:
Requires 10.1.0.3 Full Release (CD Release)

make-3.79.1

gcc-3.2.2-38

gcc-c++-3.2.2-38

glibc-2.2.2-124

openmotif-2.2.2-124

xf86 (Spatial only)

xdevel (Spatial only)

SuSE SLES9:
Requires 10.1.0.3 Full Release (CD Release)

make-3.80

gcc-3.3.3-43

gcc-c++-3.3.3-43

glibc-2.3.3-98

libaio-0.3.98-18

libaio-devel-0.3.98-18

openmotif-libs-2.2.2-519.1

xfree86 (Spatial only)

xfree86-devel (Spatial only)

RHEL ES/AS 2.1:

glibc 2.2.4-32

make-3.79

openmotif-2.1.30

gcc-2.96-128

gcc-c++-2.96-128

libstdc++-2.96-128

RHEL ES/AS 3:
Refer to Note 252217.1 default RPMS (see Note 376183.1)

glibc 2.3.2-95.20

gcc-3.2.3-34

make-3.79.1

compat-db-4.0.14.5

compat-gcc-7.3-2.96.128

compat-gcc-c++-7.3-2.96.128

compat-libstdc++-7.3-2.96.128

compat-libstdc++-devel-7.3-2.96.128

gnome-libs-1.4.1.2.90-34.1

openmotif21-2.1.30-8

setarch-1.3-1

To be able to install patch 3006854 these RPMs need to be installed

glibc-devel-2.3.2-95.6.i386.rpm

glibc-headers-2.3.2-95.20

glibc-kernheaders-2.4-8.34
Additional steps:
Note 252217.1 for additional setup requirements for RHEL3 and 9.2 x86
for Async I/O functionality to work you need to install Patch 3016968 on top of 9.2.0.3.0 or 9.2.0.4.0 or Patch 3208258 on top of 9.2.0.5.0 or 9.2.0.6.0

RHEL4:
Refer to Note 303859.1 default RPMS (see Note 376183.1)

compat-db-4.1.25-9

compat-gcc-32-3.2.3-47.3

compat-gcc-32-c++-3.2.3-47.3

compat-oracle-rhel4-1.0-3 (obtain Patch 4198954)

compat-libcwait-2.0-1 (obtain Patch 4198954)

compat-libgcc-296-2.96-132.7.2

compat-libstdc++-296-2.96-132.7.2

compat-libstdc++-33-3.2.3-47.3

gcc-3.4.3-9.EL4

gcc-c++-3.4.3-9.EL4

gnome-libs-1.4.1.2.90-44

gnome-libs-devel-1.4.1.2.90-44

libaio-devel-0.3.102-1

libaio-0.3.102-1

make-3.80-5

openmotif21-2.1.30-11

xorg-x11-deprecated-libs-devel-6.8.1-23.EL

xorg-x11-deprecated-libs-6.8.1-23.EL
Patch 4188455 required for installer to work
Set LD_ASSUME_KERNEL=2.4.19
Post install you need to apply Patch 4190568on top of the 9.2.0.6 patchset
Note 303859.1 for more specific steps for 9.2.0.6 on RHEL4

SuSE SLES8:

gcc-3.2.2-38

glibc-2.2.2-124

make-3.79.1

openmotif-2.2.2-124

SuSE SLES9:
Refer to Note 427976.1 default RPMS (see Note 386391.1)

glibc-2.3.3

gcc-3.3.3

gcc-c++-3.3.3

libaio-0.3.98

libaio-devel-0.3.98

make-3.80

openmotif-libs-2.2.2-519.1

orarun-1.8-109
Additional steps for SLES9 for 9.2 32bit x86:
Install 9.2.0.4 (Complete release) and then apply 9.2.0.5 and 9.2.0.5 one-off Patch 3809563 or 9.2.0.6 patchset

If using Bourne, Bash, or Korn shell: ( /usr/lib/libInternalSymbols.so can be obtained from the orarun package )
ORACLE_BASE= ; export ORACLE_BASE
LD_ASSUME_KERNEL=2.4.21; export LD_ASSUME_KERNEL
LD_PRELOAD=/usr/lib/libInternalSymbols.so ; export LD_PRELOAD
for Async I/O functionality to work you need to install Patch 3208258 on top of 9.2.0.5.0 or 9.2.0.6.0

make-3.79, and binutils-2.10.

GLIBC package version 2.1.3 or higher

GLIBC package version 2.1

GNU C Library, version 2.0.6
GLIBC package version 2.1

GNU C Library, version 2.0.7
TCL library (libtcl.so), version 8.0.2-16

Linux x86 Kernel Settings

kernel.shmmni = 4096
kernel.sem = 250 32000 100 128
fs.file-max = 6815744 ~~512 x processes (for example 6815744 for 13312 processes)~~
net.ipv4.ip_local_port_range = 9000 65500
net.core.rmem_default = 262144
net.core.rmem_max = 4194304
net.core.wmem_default = 262144
net.core.wmem_max = 1048576

SEMMSL 250
SEMMNS 32000
SEMMNI 128
SEMOPM 100
SHMMAX RAM times 0.5 Note 567506.1)
SHMMNI 4096
SHMALL = SHMMAX/pagesize
FILE-MAX =6815744 ~~512* Processes~~
IP_LOCAL_PORT_RANGE 9000 65500
RMEM_DEFAULT 262144
RMEM_MAX 4194304
WMEM_DEFAULT 262144
WMEM_MAX ~~262144~~1048576
NET.IPV4.TCP_RMEM 4194304 4194304 4194304
NET.IPV4.TCP_WMEM 262144 262144 262144

SuSE SLES9:
SEMMSL 250
SEMMNS 32000
SEMMNI 128
SEMOPM 100
SHMMAX RAM times 0.5 (Note 567506.1)
SHMMNI 4096
SHMALL = SHMMAX/pagesize
FILE-MAX 65536
IP_LOCAL_PORT_RANGE 9000 65500
RMEM_DEFAULT 262144
RMEM_MAX 2097152
WMEM_DEFAULT 262144
WMEM_MAX 262144
NET.IPV4.TCP_RMEM 1048576 1048576 1048576
NET.IPV4.TCP_WMEM 262144 262144 262144

Other Linux OS:
SEMMSL 250
SEMMNS 32000
SEMMNI 128
SEMOPM 100
SHMMAX RAM times 0.5 (Note 567506.1)
SHMMNI 4096
SHMALL = SHMMAX/pagesize
FILE-MAX 65536
IP_LOCAL_PORT_RANGE 9000 65500
RMEM_DEFAULT 262144
RMEM_MAX 2097152
WMEM_DEFAULT 262144
WMEM_MAX 262144
NET.IPV4.TCP_RMEM 1048576 1048576 1048576
NET.IPV4.TCP_WMEM 262144 262144 262144

SEMMNI 100
SEMMNS 256
SEMMSL 100
SEMOPM 100
SEMVMX 32767
SHMMAX 2147483648
One-half the size of your system's physical memory. Check your system for additional restrictions.
SHMMIN 1
SHMMNI 4096
SHMSEG 4096

SHMMAX 0.5*(physical memory present in machine) but not greater then 4Gb
SHMMIN 1
SHMMNI 100
SHMSEG 10
SEMMNI 100
SEMMSL Set to 10 plus the largest PROCESSES parameter of any Oracle database on the system.
SEMMNS Set to the sum of the PROCESSES parameter for each Oracle database, adding the largest one twice, then add an additional 10 for each database.
SEMOPM 100
SEMVMX 32767

SHMMAX 0.5 *(physical memory present in machine) but not greater then 4Gb
SHMMIN 1
SHMMNI 100
SHMSEG 10
SEMMNI 100
SEMMSL Set to 10 plus the largest initsid.ora PROCESSES parameter of an Oracle database on the system.
SEMMNS Set to the sum of the PROCESSES parameter for each Oracle database except the largest one, plus 2 times the largest PROCESSES value, plus 10 times the number of Oracle databases.
SEMOPM 100
SEMVMX 32767

SHMMAX (1/4 of RAM) but not greater then 4Gb
SHMMIN 1
SHMMNI 100
SHMSEG 10
SEMMNS 200
SEMMNI 70
SEMMSL Equal to or greater than the value of the
PROCESSES initialization parameter.

SHMMAX (1/4 of RAM) but not greater then 4Gb
SHMMIN 1
SHMMNI 100
SHMSEG 10
SEMMNS 200
SEMMNI 70
SEMMSL Equal to or greater thanthe value of the
PROCESSES initialization parameter.

Oracle Version 11.2 11.1 10.2 10.1 9.2.0 9.0.1 8.1.7 8.1.6 8.1.5 8.0.6 8.0.5

Linux x86_64 EM64T AMD64 OS
(See Note 225710.1 for supported kernels) andNote 265262.1for "Things to know about Linux"

o RHEL4,OEL4 - update 7 or greater
o RHEL5,OEL5 - 5.2 or greater
o RHEL6,OEL6 - 6.0 or greater
o SLES10 - Kernel 2.6.16.21-0.8 or greater
o SLES11 - Kernel 2.6.27.19-5 or greater
o Asianux Server 3 SP2

NOTE: On RHEL6/OEL6, only 11.2.0.3 is certified (not 11.2.0.1 or 11.2.0.2)

Asianux 2.0, [Red Hat,Oracle] Enterprise Linux 4.0:
2.6.9

Asianux Server 3, [Red Hat,Oracle] Enterprise Linux 5.0:
2.6.18

SUSE Linux Enterprise Server 10:
2.6.16.21

SuSE Linux Enterprise Server 11:
2.6.27.19-5 or greater

o Red Hat Enterprise Linux ( RHEL 3 ) AS/ES (Update 4 or later)
2.4.21-27.EL
o RHEL4 AS/ES (Update 1 or later) or OEL4
2.6.9-11.EL
o RHEL5 AS/ES or OEL5
2.6.18-8 or higher
o SUSE Linux Enterprise Server 9.0 (SLES9) with SP2 or later
2.6.5-7.201
o SuSE Linux Enterprise Server 10 (SLES10)
2.6.16.21-0.8 (or later)
o SuSE Linux Enterprise Server 11 (SLES11)
2.6.27.19-5 or greater
o Asianux 2.0

o Red Hat Enterprise AS/ES 3.0 (Update 2 or higher)
2.4.21-15.EL
o Red Hat Enterprise AS/ES 4.0 (Update 1 or higher)
2.6.9-11.EL smp
o SuSE SLES8 (Service Pack 3 or higher)
2.4.21-185-smp
o SuSE SLES9
2.6.5-7.97
o Asianux 1.0
requires 10.1.0.3

o Red Hat Enterprise AS/ES 3.0
2.4.21-9
o Red Hat Enterprise AS/ES 4.0
minimum patchset level is 9.2.0.7.0
o SuSE SLES8
2.4.21-185
o SuSE SLES9
9.2.0.6 Required - needed for EM64T patch 4261532 & patch 4233179

Linux x86_64 EM64T AMD64 Disk Space 3.8Gb Database 1.68G Database
3.8G to 4.4G Software 1.2G Database
1.5 to 3.5G Install 1.2G Database
1.5G Software
1G Companion
150M-650M Client 4.5G

Linux x86_64 EM64T AMD64 RAM

Database: minimum 1GB, recommended 2GB

Grid Infrastructure for standalone server: minimum 1.5GB (plus another 1GB if installing Database too), recommended 4GB

1GB

512Mb
256Mb(Client/Compan)

512Mb

Linux x86_64 EM64T AMD64 swap

11.2 DB Installation Guide for Linuxsays:
If RAM between 1 GB and 2 GB then 1.5 times the size fo RAM.
If RAM between 2 GB to 16 GB then equal to the size of RAM.
If RAM greater than 16 GB then 16 GB.

11.2 Grid Infrastructure (GI) Installation Guide for Linux says:
If RAM between 2 GB and 8 GB then 2 times the size fo RAM.
If RAM between 8 GB to 32 GB then 1.5 times the size of RAM.
If RAM greater than 32 GB then 32 GB.

If RAM 1 GB and 2 GB
then 1.5 times the size fo RAM.
If RAM 2 GB to 16 GB
then equal to the size fo RAM.
If RAM greater than 16 GB
then 16 GB

Automatic Memory Management
Starting with Oracle Database 11g, the Automatic Memory Management feature requires more shared memory (/dev/shm) and file descriptors. The shared memory should be sized to be at least the greater of MEMORY_MAX_TARGET and MEMORY_TARGET for each Oracle instance on the computer. To determine the amount of shared memory available, enter the following command: # df -k /dev/shm/

Note: MEMORY_MAX_TARGET and MEMORY_TARGET cannot be used when LOCK_SGA is enabled or with huge pages on Linux

If RAM = 1024MB to 2048Mb
then 1.5 times RAM
elseif RAM > 2048MB and < 8192MB
then match RAM
else RAM > 8192MB
then .75 times RAM

1Gb or match RAM
512Mb(Client/Compan)

1Gb or match RAM

Linux x86_64 EM64T AMD64 tmp 1024Mb 400Mb 400Mb 400Mb 400Mb

Linux x86_64 EM64T AMD64 JDK & JRE You can use Sun JDK 1.5.0-06 with the JNDI extension JDK versions with the Oracle Java Database Connectivity and Oracle Call Interface drivers.
However, these are not mandatory for the installation You can use Sun JDK 1.5.0-06 with the JNDI extension JDK versions with the Oracle Java Database Connectivity and Oracle Call Interface drivers.
However, these are not mandatory for the installation JDK 1.4.2_08 is installed JDK 1.4.2_02 is installed o Sun JDK 1.4.2_03 is installed

Linux x86_64 EM64T AMD64 Patches/
Packages

RHEL6,OEL6:
Refer to Note 1441282.1

RHEL5,OEL5:
Refer to Note 880989.1
binutils-2.17.50.0.6-6.el5 (x86_64)
compat-libstdc++-33-3.2.3-61 (x86_64) << both ARCH's are required. See next line.
compat-libstdc++-33-3.2.3-61 (i386) << both ARCH's are required. See previous line.
elfutils-libelf-0.125-3.el5 (x86_64)
glibc-2.5-24 (x86_64) << both ARCH's are required. See next line.
glibc-2.5-24 (i686) << both ARCH's are required. See previous line.
glibc-common-2.5-24 (x86_64)
ksh-20060214-1.7 (x86_64)
libaio-0.3.106-3.2 (x86_64) << both ARCH's are required. See next line.
libaio-0.3.106-3.2 (i386) << both ARCH's are required. See previous line.
libgcc-4.1.2-42.el5 (i386) << both ARCH's are required. See next line.
libgcc-4.1.2-42.el5 (x86_64) << both ARCH's are required. See previous line.
libstdc++-4.1.2-42.el5 (x86_64) << both ARCH's are required. See next line.
libstdc++-4.1.2-42.el5 (i386) << both ARCH's are required. See previous line.
make-3.81-3.el5 (x86_64)
The remaining Install Guide requirements will have to be installed:
elfutils-libelf-devel-0.125-3 (x86_64)
a.) requires elfutils-libelf-devel-static-0.125-3 (x86_64) as a prerequisite, as listed below.
b.) elfutils-libelf-devel and elfutils-libelf-devel-static each depend upon the other. Therefore, they must be installed together, in one (1) "rpm -ivh" command as follows:
rpm -ivh elfutils-libelf-devel-0.125-3.el5.x86_64.rpm elfutils-libelf-devel-static-0.125-3.el5.x86_64.rpm
glibc-headers-2.5-24 (x86_64)
a.) requires kernel-headers-2.6.18-92 (x86_64) as a prerequisite, as listed below
glibc-devel-2.5-24 (x86_64) << both ARCH's are required. See next item.
glibc-devel-2.5-24 (i386) << both ARCH's are required. See previous item.
gcc-4.1.2-42.el5 (x86_64)
a.) requires libgomp-4.1.2-42 (x86_64) as a prerequisite, as listed below
libstdc++-devel-4.1.2-42 (x86_64)
gcc-c++-4.1.2-42.el5 (x86_64)
libaio-devel-0.3.106-3.2 (x86_64) << both ARCH's are required. See next item
libaio-devel-0.3.106-3.2 (i386) << both ARCH's are required. See previous item.
sysstat-7.0.2-1 (x86_64)
unixODBC-2.2.12 (x86_64) << both ARCH's are required. See next item and Note:762206.1
unixODBC-2.2.12 (i386) << both ARCH's are required. See previous item and Note:762206.1
unixODBC-devel-2.2.12 (x86_64) << both ARCH's are required. See next item and Note:762206.1
unixODBC-devel-2.2.12 (i386) << both ARCH's are required. See previous item and Note:762206.1

NOTE: If you download unixODBC from ftp://ftp.unixodbc.org/pub/unixODBC/ then the header and library files are distributed together in one gzipped tar file.

RHEL4,OEL4:
Refer to Note 880942.1

SLES10:-
Refer to Note 884435.1

SLES11 :-
Refer to Note 881044.1

Asianux 2.0
[Oracle, Red Hat] Enterprise Linux 4.0
(See Note 437123.1):

default RPMs (see Note 376183.1)

binutils-2.15.92.0.2

compat-libstdc++-33-3.2.3

compat-libstdc++-33-3.2.3 (32 bit)

elfutils-libelf-0.97

elfutils-libelf-devel-0.97

gcc-3.4.5

gcc-c++-3.4.5

glibc-2.3.4-2.19

glibc-2.3.4-2.19 (32 bit)

glibc-common-2.3.4

glibc-devel-2.3.4

glibc-devel-2.3.4 (32-bit)

libaio-0.3.105

libaio-0.3.105 (32 bit)

libaio-devel-0.3.105

libgcc-3.4.5

libgcc-3.4.5 (32-bit)

libstdc++-3.4.5

libstdc++-3.4.5 (32 bit)

libstdc++-devel 3.4.5

make-3.80

sysstat-5.0.5

Asianux Server 3
[Oracle, Red Hat] Enterprise Linux 5.0
(see Note 438766.1):

default RHEL5 RPMs (see Note 376183.1)

default OEL5 RPMs (see Note 401167.1)

binutils-2.17.50.0.6

compat-libstdc++-33-3.2.3

compat-libstdc++-33-3.2.3 (32 bit)

elfutils-libelf-0.125

elfutils-libelf-devel-0.125

gcc-4.1.1

gcc-c++-4.1.1

glibc-2.5-12

glibc-2.5-12 (32 bit)

glibc-common-2.5

glibc-devel-2.5

glibc-devel-2.5-12 (32 bit)

libaio-0.3.106

libaio-0.3.106 (32 bit)

libaio-devel-0.3.106

libgcc-4.1.1

libgcc-4.1.1 (32 bit)

libstdc++-4.1.1

libstdc++-4.1.1 (32 bit)

libstdc++-devel 4.1.1

make-3.81

sysstat-7.0.0

SuSE SLES 10
(see Note 457143.1):

default-RPMs (see NOTE 386391.1)

binutils-2.16.91.0.5

compat-libstdc++-5.0.7-22.2

gcc-4.1.0

gcc-c++-4.1.0

glibc-2.4-31.2

glibc-32bit-2.4-31.2 (32 bit)

glibc-devel-2.4

glibc-devel-32bit-2.4 (32 bit)

libaio-0.3.104

libaio-32bit-0.3.104 (32 bit)

libaio-devel-0.3.104

libelf-0.8.5

libgcc-4.1.0

libstdc++-4.1.0

libstdc++-devel-4.1.0

make-3.80

sysstat-6.0.2

Note: If you did not perform a default Linux installation, you intend to use LDAP, and you want to use the scripts odisrvreg, oidca, or schemasync, then install the Korn shell RPM for your Linux distribution.

SuSE SLES 11
(see Note 1081555.1)

Red Hat Enterprise Linux 3.0:
Refer to Note 353735.1

default RPMs (see Note 376183.1)

compat-db 4.0.14-5.1

compat-gcc-7.3-2.96.128 (32 bit)

compat-gcc-c++-7.3-2.96.128 (32 bit)

compat-libstdc++-7.3-2.96.128 (32 bit)

compat-libstdc++-devel-7.3-2.96.128 (32 bit)

control-center-2.2.0.1-13

gcc-3.2.3-47

gcc-c++-3.2.3-47

gdb-6.1post-1.20040607.52

glibc-2.3.2-95.30

glibc-common-2.3.2-95.30

glibc-devel-2.3.2-95.30

glibc-devel-2.3.2-95.20 (32 bit)

gnome-libs-1.4.1.2.90-34.2 (32 bit)

libaio-0.3.96-3

libaio-devel-0.3.96-3

libstdc++-3.2.3-47

libstdc++-devel-3.2.3-47

make-3.79.1-17

openmotif-2.2.3-3.RHEL3

sysstat-5.0.5-5.rhel3

setarch-1.3-1

[Red Hat,Oracle] Enterprise Linux 4.0:
Refer to Note 339510.1

default RPMs (see Note 376183.1)

binutils-2.15.92.0.2-13.0.0.0.2.x86_64Download here or you can install binutils-2.15.92.0.2-18.x86_64.rpm from RHEL4 Update 3.

compat-db-4.1.25-9.x86_64.rpm

compat-gcc-32-c++ )see Note 430526.1)
Patch 5240469 to correct bad genoccish file

compat-libstdc++-33-3.2.3-47.3.x86_64.rpm

compat-libstdc++-33-3.2.3-47.3.i386.rpm

control-center-2.8.0-12.x86_64.rpm

gcc-3.4.3-47.x86_64.rpm

gcc-c++-3.4.3-47.x86_64.rpm

glibc-2.3.4-2.9.x86_64.rpm

glibc-2.3.4-2.9.i386.rpm

glibc-common-2.3.4-2.9.x86_64.rpm

glibc-devel-2.3.4-2.9.x86_64.rpm

glibc-devel-2.3.4-2.9.i386.rpm

glibc-headers-2.3.4-2.9.x86_64.rpm

glibc-kernheaders-2.4-9.1.87.x86_64.rpm

gnome-libs-1.4.1.2.90-44.1.x86_64

libaio-0.3.103-3.i386.rpm

libaio-0.3.103-3.x86_64.rpm

libgcc-3.4.3-9.EL4

libstdc++-3.4.3-22.1.x86_64

libstdc++-devel-3.4.3-22.1.x86_64

make-3.80-5.x86_64.rpm

pdksh-5.2.14-30.x86_64.rpm

sysstat-5.0.5-1.x86_64.rpm

util-linux-2.12a-16.EL4.23.x86_64 (for raw devices)

xorg-x11-deprecated-libs-6.8.1-23

xscreensaver-4.18-5.rhel4.2.x86_64.rpm

[Red Hat,Oracle] Enterprise Linux 5.0
Refer to Note 421308.1
Since RHEL5/OEL5 are not recognized by runInstaller do:
./runinstaller -ignoreSysPrereqs

default RHEL5 RPMs (see Note 376183.1)

default OEL5 RPMs (see Note 401167.1)

~~compat-gcc-34-3.4.6-4~~

~~compat-gcc-34-c++-3.4.6-4~~

compat-libstdc++-33-3.2.3-61.i386.rpm

compat-libstdc++-33-3.2.3-61.x86_64.rpm

gcc-c++-4.1.1-52.el5.x86_64.rpm and all its dependent packages.
The dependent packages are:
libstdc++-devel-4.1.1-52.el5.x86_64.rpm
glibc-headers-2.5-12.x86_64.rpm
glibc-devel-2.5-12.i386.rpm
glibc-devel-2.5-12.x86_64.rpm
libgomp-4.1.1-52.el5.x86_64.rpm
gcc-4.1.1-52.el5.x86_64.rpm

libXp-1.0.0-8.i386.rpm

sysstat-7.0.0-3.el5.x86_64.rpm

util-linux-2.13-0.44.el5.x86_64 (for raw devices)

SUSE Linux Enterprise Server 9:
Refer to Note 365607.1

default-RPMs (see NOTE 386391.1)

binutils-2.15.90.0.1.1-32.5

db1-1.85-85.1

gcc-3.3.3-43.24

gcc-c++-3.3.3-43.24

glibc-2.3.3-98.28

glibc-32bit-9-200506071326

glibc-devel-2.3.3-98-47

glibc-devel-32bit-9-200506062332

libaio-0.3.102.1.2

libaio-devel-0.3.102.1.2

gnome-libs-1.4.1.7-671.1

gnuplot-3.7.3-256.1 (sysstat required RPM)

libstdc++-3.3.3-43.24

libstdc++-devel-3.3.3-43.24

make-3.80-184.1

orbit-0.5.17-330.1 (gnome-libs required RPM)

plotutils-2.4.1-575.1 (sysstat required RPM)

pdksh-5.2.14-780.1

sysstat-5.0.1-35.1

XFree86-libs-4.3.99.902.43.48

SUSE Linux Enterprise Server 10:
Refer to Note 373681.1
Since SLES10 is not recognized by runInstaller do:
./runinstaller -ignoreSysPrereqs

default-RPMs (see NOTE 386391.1)

glibc-devel-2.4-31.2.x86_64.rpm

gcc-4.1.0-28.4.x86_64.rpm

libstdc++-devel-4.1.0-28.4.x86_64.rpm

gcc-c++-4.1.0-28.4.x86_64.rpm

glibc-devel-32bit-2.4-31.2.x86_64.rpm

libaio-devel-0.3.104-14.2.x86_64.rpm

SuSE Linux Enterprise Server 10 special instructions: 1. Execute runInstaller with the -ignoreSysPrereqs option.

SUSE Linux Enterprise Server 11:
Refer to Note:956194.1 for a list of required SLES11 packages
Since SLES11 is not recognized by runInstaller do:
./runinstaller -ignoreSysPrereqs

RHEL 3 (Update 2):
Refer to Note 351679.1

default-RPMs (see NOTE 376183.1)

make-3.79.1

gcc-3.2.3-34

glibc-2.3.2-95.20

glibc-devel-2.3.2-95.20

glibc-devel-2.3.2-95.20 (32 bit)

compat-db-4.0.14-5

compat-gcc-7.3-2.96.128 (32 bit)

compat-gcc-c++-7.3-2.96.128 (32 bit)

compat-libstdc++-7.3-2.96.128 (32 bit)

compat-libstdc++-devel-7.3-2.96.128 (32 bit)

gnome-libs-1.4.1.2.90-34.1 (32 bit)

openmotif21-2.1.30-8 (32 bit)

setarch-1.3-1

libaio-0.3.96-3

libaio-devel-0.3.96-3

XFree86-libs-4.3.0-62 (32bit)

RHEL 4:
Refer to Note 390900.1 Requires My Oracle Support (MOS) patch 5201236Bug 4387087

default-RPMs (see NOTE 376183.1)

glibc-kernheaders-2.4-9.1.87 (x86_64)

glibc-headers-2.3.4-2.9 (x86_64)

glibc-devel-2.3.4-2.9 (x86_64)

glibc-devel-2.3.4-2.9 (i386)

libstdc++-devel-3.4.3-22.1 (x86_64)

gcc-3.4.3-22.1 (x86_64)

gcc-c++-3.4.3-22.1 (x86_64)

sysstat-5.0.5-1 (x86_64)

Note:
openmotif21-2.1.30-11.RHEL4.2 is required to install Oracle demos.
GNU Compiler Collection (GCC) 2.96 is not supported on Red Hat Enterprise Linux 4.0.
Gcc 3.2.3 is required for OCCI application

SuSE SLES8 (Service Pack 3 or later):

make-3.79.1

gcc-3.3.3-43

gcc-c++-3.3.3-43

glibc-2.2.5-213

glibc-32bit-8.1-9

glibc-devel-32bit-8.1-9

openmotif-2.2.2-124

libaio-0.3.96-3

libaio-devel-0.3.96-3

SuSE SLES9:

gcc-3.3.3-43

gcc-c++-3.3.3-43

glibc-2.3.3-98

glibc-32bit-9 (Bug 4405422)

glibc-devel-32bit-9 (Bug 4405422)

libaio-0.3.98-18

libaio-devel-0.3.98-18

make-3.80

openmotif-libs-2.2.2-519.1

RHEL ES/AS 3
Please refer to Note: 308588.1LD_ASSUME_KERNEL=2.4.19

glibc 2.3.2-95.x86_64

gcc-3.2.3-24.x86_64

gcc-c++-3.2.3-24.x86_64

libstdc++-3.2.3-24.i386

libstdc++-devel-3.2.3-24.x86_64

libstdc++-3.2.3-24.x86_64

glibc-devel-2.3.2-95.3.i386 (Foot 1)

glibc-2.3.2-95.6.i686

make 3.79.1.x86_64

gnome-libs-1.4.1.2.90-34.1.i386 (Foot 2)

ORBit-0.5.17-10.4.i386

audiofile-0.2.3-7.1.i386

esound-0.2.28-5.1.i386

gtk+-1.2.10-27.1.i386

imlib-1.9.13-12.i386

libpng10-1.0.13-8.i386

libungif-4.1.0-15.i386

tcp_wrappers-7.6-34.i386

setarch-1.3-1.x86_64

libaio-0.3.96-3.x86_64
Note:The x86_64 rpms are on the RHEL 3 x86_64 distribution. The i386 rpms are on the RHEL 3 x86 distribution.

o Footnote 1
This package might require the --force option during installation.
o Footnote 2
This package might require the --force option during installation if 64-bit gnome packages are installed. Oracle recommends that you do not install 64-bit gnome packages if they are not required for other applications.

RHEL ES/AS 4

Please refer to Note: 353529.1

a "default-RPMs" installation of RHEL AS/ES 4 update 1. Additional RPMs may be needed if a "less-than-default-RPMs" installation of RHEL AS/ES 4 update 1 is performed.

compat-gcc-32-3.2.3-47.3.x86_64.rpm

compat-gcc-32-c++-3.2.3-47.3.x86_64.rpm

glibc-kernheaders-2.4-9.1.87.x86_64.rpm

glibc-headers-2.3.4-2.9.x86_64.rpm

glibc-devel-2.3.4-2.9.x86_64.rpm

libstdc++-devel-3.4.3-22.1.x86_64.rpm

glibc-devel-2.3.4-2.9.i386.rpm

libaio-0.3.103-3.x86_64.rpm

ORBit-0.5.17-14.i386.rpm

gnome-libs-1.4.1.2.90-44.1.i386.rpm
The x86_64 packages are on the Red Hat Enterprise Linux 4 x86-64 distribution.
The i386 packages are also on the Red Hat Enterprise Linux 4 x86-64 distribution.

SuSE SLES8 (Service Pack 3 or higher)

glibc-2.2.5-213.x86_64

glibc-32bit-8.1-9.i586

glibc-devel-32bit-8.1-9.i586

gcc-33-3.3-43.x86_64

gcc-33-c++3.3-43.x86_64

libstdc++-33-3.3-43.x86_64

libstdc++-devel-33-3.3-43.x86_64

make-3.79.1-42.x86_64

libaio-0.3.15-138.x86_64 (This version of libaio is required for asynchronous I/O.)
Note: Create a symbolic link such that /usr/bin/gcc points to /opt/gcc33/bin/gcc. Otherwise the installation fails with relinking errors.

SuSE SLES9
Please refer to Note: 361169.1
Set LD_ASSUME_KERNEL=2.4.20

compat-2004.7.1-1.2

compat-32bit-9-200407011229

XFree86-libs-4.3.99.902-43.22

XFree86-libs-32bit-9-200407011229

libaio-devel-0.3.98-18.4

libaio-32bit-9-200407011229

libaio-0.3.98-18.4

libaio-devel-32bit-9-200407011229

glibc-32bit-9-200506071326

glibc-devel-32bit-9-200506071326 orarun-1.8-31

Linux x86_64 EM64T AMD64 Kernel Settings

kernel.shmmni = 4096
kernel.sem = 250 32000 100 128
fs.file-max = 6815744 ~~512 x processes (for example 6815744 for 13312 processes_~~
net.ipv4.ip_local_port_range = 9000 65500
net.core.rmem_default = 262144
net.core.rmem_max = 4194304
net.core.wmem_default = 262144
net.core.wmem_max = 1048576
kernel.shmall = physical RAM size / pagesize For most systems, this will be the value 2097152. See Note: 301830.1 for more information.
kernel.shmmax = RAM times 0.5 (or higher at customer's discretion - see Note:567506.1)
kernel.shmmni = 4096
kernel.sem = 250 32000 100 128

SEMMSL 250
SEMMNS 32000
SEMMNI 128
SEMOPM 100
SHMMAX RAM times 0.5 (Note 567506.1)
SHMMNI 4096
SHMALL = SHMMAX/pagesize (Note:301830.1)
FILE-MAX 6815744 ~~512 * Processes~~
IP_LOCAL_PORT_RANGE 9000 65500
RMEM_DEFAULT 262144
RMEM_MAX 4194304
WMEM_DEFAULT 262144
WMEM_MAX ~~262144~~ 1048576
NET.IPV4.TCP_RMEM (RMEM_DEFAULT) (RMEM_DEFAULT) (RMEM_MAX)
NET.IPV4.TCP_WMEM (WMEM_DEFAULT) (WMEM_DEFAULT) (WMEM_MAX)

To increase the shell limits:
1. Add the following lines in the /etc/security/limits.conf file:
oracle soft nproc 2047
oracle hard nproc 16384
oracle soft nofile 1024
oracle hard nofile 65536
2. Add the following line to the /etc/pam.d/login file, if it does not already exist:
~~session required /lib/security/pam_limits.so~~
session required pam_limits.so Note 437123.1
Lines from the Fix section of Note 301665.1
3. Depending on the oracle user's default shell, make the following changes to the default shell startup file:
For the Bourne, Bash, or Korn shell, add the following lines in the /etc/profile file (or the /etc/profile.local file on SUSE Linux Enterprise Server systems):
if [ $USER = "oracle" ]; then
if [ $SHELL = "/bin/ksh" ]; then
ulimit -p 16384
ulimit -n 65536
else
ulimit -u 16384 -n 65536
fi
fi
For the C shell, add the following lines in the /etc/csh.login file (or the /etc/csh.login.local file on SUSE Linux Enterprise Server systems):
if ( $USER == "oracle" ) then
limit maxproc 16384
limit descriptors 65536
endif

SEMMSL 250
SEMMNS 32000
SEMMNI 128
SEMOPM 100
SHMMAX RAM times 0.5 (note:567506.1)
SHMMNI 4096
SHMALL = SHMMAX/pagesize (note:301830.1)
FILE-MAX 65536
IP_LOCAL_PORT_RANGE 9000 65500
RMEM_DEFAULT 262144
RMEM_MAX 2097152
WMEM_DEFAULT 262144
WMEM_MAX ~~262144~~ 1048576
NET.IPV4.TCP_RMEM (RMEM_DEFAULT) (RMEM_DEFAULT) (RMEM_MAX)
NET.IPV4.TCP_WMEM (WMEM_DEFAULT) (WMEM_DEFAULT) (WMEM_MAX)

SEMMSL 250
SEMMNS 32000
SEMMNI 128
SEMOPM 100
SEMVMX 32767
SHMMAX 2147483648
One-half the size of your system's physical memory. Check your system for additional restrictions.
SHMMNI 4096
SHMALL = SHMMAX/pagesize (note:301830.1)
FILE-MAX 65536
IP_LOCAL_PORT_RANGE 9000 65500
To use hugepages, or to accommodate the VLM window size on Red Hat Enterprise Linux 4.0, you must increase the default maximum size of the per-process locked memory. To increase the per-process maximum locked memory limit, add the following lines to the /etc/security/limits.conf file, where oracle is the user that administers the database. Refer Note 361468.1:
oracle soft memlock 5243000
oracle hard memlock 5243000

Oracle Version 11.2 11.1 10.2 10.1 9.2.0 9.0.1 8.1.7 8.1.6 8.1.5 8.0.6 8.0.5

Linux Itanium OS
(See Note 225710.1 for supported kernels),(SeeNote 1130325.1for Support Status-Oracle Database on Linux Itanium)and Note 265262.1 for "Things to know about Linux" NA Not Available o RHEL AS/ES 3.0 (Update 4 or higher)
2.4.21-20.EL
o RHEL AS/ES 4.0 (Update 1 or higher)
2.6.9-11.EL
o SuSE SLES9 (SP2 or higher)
2.6.5-199
o SuSE SLES-10
o RHEL 5.0 (Note 748378.1)
2.6.18-8 or higher
Note: for all Itanium systems using "Montecito" processors, refer tonote:400227.1 for special installation instructions o RHEL AS/ES 2.1 (Update 6 or higher)
2.4.18-e52
o RHEL AS/ES 3.0 (Update 4 or higher)
2.4.21-27.EL
o RHEL AS/ES 4.0 (Update 1 or higher)
2.6.9-11.EL.smp
o Red Flag Advanced Server 4.0 for Itanium 2 (China and Hong Kong only)
o SuSE SLES8 (SP4 or later)
2.4.21-278
o SuSE SLES9 (SP1 or later)
2.6.5-7.139
Note: for all Itanium systems using "Montecito" processors, refer tonote:400227.1 for special installation instructions o Red Hat Enterprise AS/ES 2.1
2.4.18-e.14
o Red Hat Enterprise AS/ES 3.0
o Red Hat Enterprise AS/ES 4.0
2.6.9-11
o SuSE SLES8
o SuSE SLES9
o United Linux 1.0
o Red Flag Advanced Server 4.0 for Itanium 2 (China and Hong Kong only)
2.4.18-e14.ia64.rpm
Note: for all Itanium systems using "Montecito" processors, refer tonote:400227.1 for special installation instructions

Linux Itanium Disk Space NA Not Available 1.2G Database
1.5 to 3.5G Install 1.2G Database
1.5G Software
1G Companion
150M-650M Client 4.5G

Linux Itanium RAM NA Not Available 1Gb 512Mb
256Mb(Client/Compan) 512Mb

Linux Itanium swap NA Not Available If RAM = 1024MB to 2048Mb
then 1.5 times RAM
elseif RAM > 2048MB and < 8192MB
then match RAM
else RAM > 8192MB
then .75 times RAM 1Gb or match RAM
512Mb(Client/Compan) 1Gb or match RAM

Linux Itanium tmp NA Not Available 400Mb 400Mb 400Mb

Linux Itanium JDK & JRE NA Not Available JDK 1.4.2_08 is installed JDK 1.4.2_02 is installed o Sun JDK 1.4.1 is installed but is mandatory to patch it to 1.4.2

Linux Itanium Patches/
Packages

Not Available

Red Hat Enterprise Linux 3.0:

make-3.79.1-17

control-center-2.2.0.1-13

gcc-3.2.3-47

gcc-c++-3.2.3-47

gdb-6.1post-1.20040607.52

glibc-2.3.2-95.30

glibc-common-2.3.2-95.30

glibc-devel-2.3.2-95.30

glibc-devel-2.3.2-95.20 (32 bit)

compat-db-4.0.14-5.1

compat-gcc-7.3-2.96.128

compat-gcc-c++-7.3-2.96.128

compat-libstdc++-7.3-2.96.128

compat-libstdc++-devel-7.3-2.96.128

gnome-libs-1.4.1.2.90-34.2 (32 bit)

libstdc++-3.2.3-47

libstdc++-devel-3.2.3-47

openmotif-2.2.3-3.RHEL3

sysstat-5.0.5-5.rhel3

setarch-1.3-1

libaio-0.3.96-3

libaio-devel-0.3.96-3

Red Hat Enterprise Linux 4.0:

binutils-2.15.92.0.2-10.EL4

compat-db-4.1.25-9

control-center-2.8.0-12

gcc-3.2.3-47 (OCCI does not support 3.4.3)

gcc-c++-3.2.3-47 (OCCI does not support 3.4.3)

glibc-2.3.4-2

glibc-common-2.3.4-2

gnome-libs-1.4.1.2.90-44.1

libaio-0.3.102-1

libstdc++-3.4.3-9.EL4

libstdc++-devel-3.4.3-9.EL4

make-3.80-5

pdksh-5.2.14-30

sysstat-5.0.5-1

compat-libstdc++-33-3.2.3-47.3 Bug 4605635

SUSE Linux Enterprise Server 9:

gcc-3.3.3

gcc-c++-3.3.3

glibc-2.3.3

libaio-0.3.102-1.2ia64

libaio-devel-0.3.102-1.2ia64

make-3.80

RHEL ES/AS 2.1 (Update 6 or higher)

gcc-2.96-129.7.2

gcc-c++-2.96-129.7.2

glibc-2.2.4-32.18

libaio-0.3.92-1

libaio-devel-0.3.92-1

libstdc++-2.96-129.7.2

libstdc++-devel-2.96-129.7.2

make-3.79.1-8

openmotif-2.1.30

cfs-1.0.11 (mentioned in 10.1.0.4 Release Note but cannot find this rpm)

RHEL ES/AS 3 (Update 1 or higher)

binutils-2.14.90.0.4-35

compat-db-4.0.14-5

compat-gcc-7.3-2.96.128

compat-gcc-c++-7.3-2.96.128

compat-libstdc++-7.3-2.96.128

compat-libstdc++-devel-7.3-2.96.128

control-center-2.2.01-13

gcc-3.2.3-20

gcc-c++-3.2.3-20

glibc-2.3.2-95.3

gnome-libs-1.4.1.2.90-34.2

make-3.79-1.17

openmotif21-2.1.30-8.i386.rpm

setarch-1.3-1

RHEL ES/AS 4 (Update 1 or higher)

binutils-2.15.92.0.2-13

compat-db-4.1.25-9

control-center-2.8.0-12

gcc-3.4.3-22.1

gcc-c++-3.4.3-22.1

glibc-2.3.4-2.9

glibc-common-2.3.4-2.9

make-3.80-5
Note: openmotif21-2.1.30-11.RHEL4.2 is required to install Oracle demos.
GNU Compiler Collection (GCC) 2.96 is not supported on Red Hat Enterprise Linux 4.0.
Gcc 3.2.3 is required for or OCCI application.

SUSE SLES8 (Service Pack 4 or higher)

gcc-3.2.2-54

glibc-2.2.5-230

make-3.79.1-328

openmotif-2.2.2-522

SUSE SLES9 (Service Pack 1 or higher)

binutils-2.15.90.0.1.1-32.5

gcc-3.3.3-43.28

gcc-c++-3.3.3-43.28

glibc-2.3.3-98.38

libaio-0.3.98-18.3

libaio-devel-0.3.98-18.3

make-3.80-184.1

openmotif-libs-2.2.2-519.4

All IA64 OS Versions - for Async I/O functionality to work you need to installPatch 3016968 on top of 9.2.0.4.0 or 9.2.0.5.0

RHEL ES/AS 2.1

glibc 2.2.4-29

gcc 2.96.0

Linux Header Patch 2.4.18 (available from Intel)

libaio-0.3.92-1

RHEL3

1. Put gcc296 and g++296 first in $PATH variable by creating the following symbolic links. These are required for the relinking of some Oracle binaries (as root)
# mv /usr/bin/gcc /usr/bin/gcc323
# mv /usr/bin/g++ /usr/bin/g++323
# ln -s /usr/bin/gcc296 /usr/bin/gcc
# ln -s /usr/bin/g++296 /usr/bin/g++

2. hostname command should return the fully qualified hostname as shown below:
- # hostname
- hostname.domainname

3. If any Java packages are installed on the system, unset the Java environment variables, for example JAVA_HOME.

4. Define and export the environment variable LD_ASSUME_KERNEL before starting the install process:
- $ export LD_ASSUME_KERNEL=2.4.19

5. Relink error for ins_oemagent.mk - Click ignore and complete the install. Apply thepatch 3119415

6. Apply 9.2.0.4 patchset (patch 3095277) for Linux Itanium in order to be certified and supported.

RHEL4
9.2.0.7 patchset is required minimum patchset

binutils-2.15.92.0.2-13

compat-db-4.1.25-9

control-center-2.8.0-12

gcc-3.4.3-22.1

gcc-c++-3.4.3-22.1

glibc-2.3.4-2.9

glibc-common-2.3.4-2.9

make-3.80-5
Define and export the environment variable LD_ASSUME_KERNEL before starting the install process:
- $ export LD_ASSUME_KERNEL=2.4.19

SuSE SLES9
The following requirements are needed for a successful installation of Oracle 9iR2 Linux Itanium on SuSE SLES9:
1. Apply 9.2.0.5 patchset (patch 3501955).
2. After installing 9.2.0.5 patchset you must install patch 4566648 to fix the following 2 issues
4566551: BACKING STORE (BSP) NEEDS PROPER ALIGNING FOR SLES9
4566614: BSP(BACKING STORE) VALUE SHOULD BE CHECKED BEFORE COPYING THE MEMORY SEGMENT
3. There is a known issue, where creation of JavaVM fails during custom DB creation. Please use the workaround described as follows in case of custom Database creation.

Remove the following eight shared libraries from $ORACLE_HOME/javavm/admin/ and restore them else where before starting database creation.
libjox9oracle_aurora_ncomp_java.so
libjox9oracle_aurora_server_tools_loadjava.so
libjox9oracle_aurora_sqljdecl.so
libjox9oracle_net_nt.so
libjox9oracle_security_jwallet.so
libjox9oracle_sql.so
libjox9org_omg_CORBA_2_3_portable.so
libjox9sun_security_action.so

Linux Itanium Kernel Settings NA Not Available Not Available SEMMSL 250
SEMMNS 32000
SEMMNI 128
SEMOPM 100
SHMMAX RAM times 0.5 (Note 567506.1)
SHMMNI 4096
SHMALL = SHMMAX/pagesize (note:301830.1)
FILE-MAX 65536
IP_LOCAL_PORT_RANGE 9000 65500
RMEM_DEFAULT 262144
RMEM_MAX 2097152
WMEM_DEFAULT 262144
WMEM_MAX 262144 WMEM_MAX 262144
NET.IPV4.TCP_RMEM (RMEM_DEFAULT) (RMEM_DEFAULT) (RMEM_MAX)
NET.IPV4.TCP_WMEM (WMEM_DEFAULT) (WMEM_DEFAULT) (WMEM_MAX) SEMMSL 250
SEMMNS 32000
SEMMNI 128
SEMOPM 100
SEMVMX 32767
SHMMAX 2147483648
One-half the size of your system's physical memory. Check your system for additional restrictions.
SHMMNI 4096
SHMALL = SHMMAX/pagesize (note:301830.1)
FILE-MAX 65536
IP_LOCAL_PORT_RANGE 9000 65500 WMEM_MAX 262144
NET.IPV4.TCP_RMEM (RMEM_DEFAULT) (RMEM_DEFAULT) (RMEM_MAX)
NET.IPV4.TCP_WMEM (WMEM_DEFAULT) (WMEM_DEFAULT) (WMEM_MAX) SEMMNI 100
SEMMNS 256
SEMMSL 100
SEMOPM 100
SEMVMX 32767
SHMMAX 2147483648
One-half the size of your system's physical memory. Check your system for additional restrictions.
SHMMIN 1
SHMMNI 4096
SHMSEG 4096

Oracle Version 11.2 11.1 10.2 10.1

Linux on 64-bit zSeries Note:1306889.1 Requirements for Installing Oracle 11gR2 on RHEL 5

Note:1290644.1 Requirements for Installing Oracle 11gR2 64-bit on SLES 11
Note:1308859.1 Requirements for Installing Oracle 11gR2 on SLES 10 Not available Note:415182.1 DB Install Requirements Quick Reference - zSeries based Linux Note:415182.1 DB Install Requirements Quick Reference - zSeries based Linux

Oracle Version 11.2 11.1 10.2 10.1 9.2.0 9.0.1 8.1.7 8.1.6 8.1.5 8.0.6 8.0.5

Linux on Power PC OS
(See Note 225710.1 for supported kernels) andNote 265262.1for "Things to know about Linux"

Not Available

o Red Hat Enterprise Linux AS/ES 5.0 (Update 1 or later)
2.6.18-53.el5
o Red Hat Enterprise Linux AS/ES 4.0 (Update 1 or later)
2.6.9-11.EL
o SUSE Linux Enterprise Server 9.0
2.6.5-7.191-pseries64
o SUSE Linux Enterprise Server 10.0
o Asianux 2.0

See Note:341507.1 for further information

Linux on Power PC Disk Space NA Not Available 1.2G Database
1.5 to 3.5G Install

Linux on Power PC RAM NA Not Available 1Gb

Linux on Power PC swap NA Not Available If RAM = 1024MB to 2048Mb
then 1.5 times RAM
elseif RAM > 2048MB and < 8192MB
then match RAM
else RAM > 8192MB
then .75 times RAM

Linux on Power PC tmp NA Not Available 400Mb

Linux on Power PC JDK & JRE NA Not Available JDK 1.4.2_08 is installed

Linux on Power PC Patches/
Packages

Not Available

Please refer to Note: 341507.1

Red Hat Enterprise Linux 4.0:

binutils-2.15.92.0.2-13

compat-libstdc++-33-3.2.3-47.3 (ppc64)

compat-libstdc++-33-3.2.3-47.3 (ppc)
Fix for: /usr/lib/libstdc++.so.5: No such file or directory (per Rel Notes)
java.lang.ExceptionInInitializerError using OUI Note 427754.1

gcc-3.4.3-22.1 (ppc)

gcc-ppc32-3.4.3-22.1 (ppc)

gcc-c++-3.4.3-22.1 (ppc)

gcc-c++-ppc32-3.4.3-22.1 (ppc)

glibc-2.3.4-2.9 (ppc64)

glibc-2.3.4-2.9 (ppc)

glibc-devel-2.3.4-2.9 (ppc)

glibc-devel-2.3.4-2.9 (ppc64)

libaio-0.3.103-3 (ppc)

libaio-0.3.103-3 (ppc64)

libaio-devel-0.3.103-3 (ppc)

libgcc-3.4.3-22.1 (ppc)

libgcc-3.4.3-22.1 (ppc64)

libstdc++-3.4.3-22.1 (ppc)

libstdc++-devel-3.4.3-22.1 (ppc64)

make-3.80-5 (ppc)

SUSE Linux Enterprise Server 9:

gcc-3.3.3-43.34

gcc-64bit-9-200505240008

gcc-c++-3.3.3-43.34

glibc-2.3.3-98.47

glibc-64bit-9-200506062240

libgcc-3.3.3-43.34

libgcc-64-bit-9-200505240008

libstdc++-3.3.3-43.34

libstdc++-devel-3.3.3-43.34

libaio-0.3.102-1.2

libaio-64bit-9-200502241152

libaio-devel-0.3.102-1.2

libaio-devel-64bit-9-200502

make-3.80-184.1

binutils-2.15.90.0.1.1-32.10

binutils-64bit-9-200505240008

An error is generated while installing Oracle Database 10.2.0.1 on Red Hat Enterprise Linux 4.0 Update 2 or later and SUSE Linux Enterprise Server 9 withservice pack 2 or later. Most of the times, the error is generated when you perform any of the following tasks:

While installing Oracle Database 10.2.0.1 after a fresh and complete installation of Red Hat Enterprise Linux 4.0 Update 2

While installing Oracle Database 10.2.0.1 after a fresh and complete installation of SUSE Linux Enterprise Server 9 with service pack 2 or later

When you start dbca or netca from the command line or Oracle Universal Installer, if Standard installation is selected
Workaround: Before installing Oracle Database 10g release 2, verify the contents of the /etc/resolv.conf file. Edit the file to make the following change:
Change the line similar to:
domain=my.net.com
To:
search=my.net.com
The original /etc/resolve.conf file can be restored after the database installation is complete.

You must install the IBM XL C/C++ Advanced Edition V7.0 for Linux Runtime Environment Component and XL Optimization Libraries component from the following link: IBM link This URL contains information and installation instructions. All the above installations must to be done before installing Oracle database. On SUSE Linux Enterprise Server 9, install the following components:

The RTE component: vacpp.rte.70.sles9.jan2006.update.tar.gz

The XL Optimization Libraries: vac.lib.70.sles9.tar
On Red Hat Enterprise Linux 4, install the following components:

The RTE component: vacpp.rte.70.rhel4.dec2005.update.tar.gz

The XL Optimization Libraries: vac.lib.70.rhel4.tar

Relink of 10.2 fails in Linux on Power After upgrade to RHEL U2. Apply Patch 4767801

Linux on Power PC Kernel Settings NA Not Available SEMMSL 250
SEMMNS 32000
SEMMNI 128
SEMOPM 100
SHMMAX RAM times 0.5 (Note 567506.1)
SHMMNI 4096
SHMALL = SHMMAX/pagesize (note:301830.1)
FILE-MAX 65536
IP_LOCAL_PORT_RANGE 9000 65500
RMEM_DEFAULT 262144
RMEM_MAX 2097152
WMEM_DEFAULT 262144
WMEM_MAX 262144

Oracle Version 11.2 11.1 10.2 10.1

Mac OS X

Not Available

Mac OS X Server 10.5.4 (Intel x86-64)

Note: Only 10.2.0.4 is available and certified

See the 10.2 Install Guide for MAC OS X (Intel)

Mac OS X Server 10.4(PowerPC)

Mac OS X Server 10.3.9(PowerPC)

Mac OS X Server 10.3.6(PowerPC)

Mac OS X Disk Space NA Not Available 1.2GB (optional pre-configured database)
1.5GB to 3.5GB (software, depending on installation type) 1.2G Database
1G Software
1G Companion
150M-1G Client

Mac OS X RAM NA Not Available 1GB or more 512Mb
256Mb(Client/Compan)

Mac OS X swap NA Not Available Equal to RAM (or more) 1Gb or match RAM
512Mb(Client/Compan)

Mac OS X tmp NA Not Available 400Mb 400Mb

Mac OS X JDK NA Not Available JDK 1.4.2_16 or higher JDK 1.4.2_05 needs to be already installed
Do this command to verify:
$ /Library/Java/Home/bin/java -version

Mac OS X Patches/
Packages

Not Available

Xcode 3.0 or later

GNU C compiler (gcc) version 4.0.1 or later (this version of gcc is included in Xcode 3.0 or later)

JDK 1.4.2_16 or higher (with the JNDI extension if you want to use the Oracle JDBC/OCI drivers)

Required Packages:

Xcode Tools 1.1 or higher

GNU C compiler (gcc) version 3.3 20030304 (Apple Computer, Inc. build 1635) *This version of gcc is included in Xcode Tools 1.2 or higher or in the Dec 2003 gccLongBranch Tools update.

X11 for Mac OS X and X11 SDK for Mac OS X (Spatial only)

OpenMotif 2.2.3 or higher (Spatial only)

Mac OS X Kernel Settings

Not Available

Following are the recommended kernel parameters:

kern.sysv.semmsl 87381
kern.sysv.semmns 87381
kern.sysv.semmni 87381
kern.sysv.semmnu 87381
kern.sysv.semume 10
kern.sysv.shmall 2097152
kern.sysv.shmmax Half the size of physical memory (in bytes)
kern.sysv.shmmni 4096
kern.maxfiles 65536
kern.maxfilesperproc 65536
net.inet.ip.portrange.first 1024
net.inet.ip.portrange.last 65000
kern.corefile core
kern.maxproc 2068
kern.maxprocperuid 2068

To improve the performance of the software on Mac OS X systems, you must increase the following shell limits:

Maximum number of open file descriptors 65536
Maximum number of processes available to a single user 2068

To increase the shell limits:

1. Change directory to the following directory:

% cd /System/Library/StartupItems/IPServices

2. Open the IPServices script using any text editor.

3. Add the following ulimit commands to the start of the StartService function in this script:

ulimit -Hu 2068
ulimit -Su 2068
ulimit -Hn 65536
ulimit -Sn 65536

4. Add the same ulimit commands to the /etc/rc script, before the SystemStarter command.

Note: If you need Mac OS X Server 10.3.6, please go to here:
Apple URL
To obtain the latest update for Mac OS X Server 10.3.6, please go to:
Latest Update

To obtain Mac OS X Server 10.3.9 and the software update, send an email message to [email protected] . You will receive an automatic response that contains links to the required patch and to the Mac OS X Server 10.3.9 installation software.
Note: You do not need to include a message or title with the email.

To install Oracle 10.1.0.5 on MACOSX 10.4 (Tiger OS) PowerPC based systems :
Install Oracle Database 10.1.0.3 - software only. Please do not create the database.
Perform a software upgrade from 10.1.0.3 to 10.1.0.5. Invoke OUI from 10.1.0.5 and choose software upgrade only.
After 10.1.0.5 software upgrade, create database using the Database Configuration Assistant (DBCA)". DBCA is found under $ORACLE_HOME/bin . Just Invoke this executable and choose create database option.

Following are the recommended kernel parameters:

kern.corefile core
kern.sysv.semmni 87381
kern.sysv.semmns 87381
kern.sysv.semmnu 87381
kern.sysv.semmsl 87381
kern.sysv.semume 10
kern.sysv.maxproc 2068
kern.sysv.maxprocperuid 2068

To improve the performance of the software on Mac OS X systems, you must increase the following shell limits:

Shell Limit / Hard Limit
Maximum number of open file descriptors 65536
Maximum number of processes available to a single user 2068

To increase the shell limits:

Change directory to the following directory:

# cd /System/Library/StartupItems/IPServices

Open the IPServices script using any text editor.

Add the following ulimit commands to the start of the StartService function in this script:

ulimit -Hu 2068
ulimit -Su 2068
ulimit -Hn 65536
ulimit -Sn 65536

Add the same ulimit commands to the /etc/rc script, before the SystemStarter command.

Oracle Version 11.2 11.1 10.2 10.1 9.2.0 9.0.1 8.1.7 8.1.6 8.1.5 8.0.6 8.0.5

oracle安装对OS的要求

你可能感兴趣的:(Oracle转帖,Oracle管理)