高通 SDM450插入充电器开机log

Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.3-00221
S - IMAGE_VARIANT_STRING=JAASANAZA
S - OEM_IMAGE_VERSION_STRING=scmbuild
S - Boot Config, 0x000000e0
B - 269 - PBL, Start
B - 3144 - bootable_media_detect_entry, Start
B - 106578 - bootable_media_detect_success, Start
B - 106584 - elf_loader_entry, Start
B - 108520 - auth_hash_seg_entry, Start
B - 108799 - auth_hash_seg_exit, Start
B - 136813 - elf_segs_hash_verify_entry, Start
B - 260498 - PBL, End
B - 221948 - SBL1, Start
B - 266570 - pm_device_init, Start
B - 269071 - BOOT_DUMP: PMi8950_PON_FSM =0x20895 :DATA=0x9
B - 271236 - PON REASON:PM0:0x20 PM1:0x20
D - 29402 - pm_device_init, Delta
B - 296002 - usb: hs_phy_nondrive_start
B - 297192 - usb: hs_phy_nondrive_finish
B - 300821 - boot_flash_init, Start
D - 0 - boot_flash_init, Delta
B - 307714 - boot_config_data_table_init, Start
D - 5886 - boot_config_data_table_init, Delta - (0 Bytes)
B - 318145 - CDT version:3,Platform ID:11,Major ID:1,Minor ID:0,Subtype:0
B - 324794 - sbl1_ddr_set_params, Start
B - 329308 - cpr_init, Start
D - 1128 - cpr_init, Delta
B - 333975 - Pre_DDR_clock_init, Start
D - 213 - Pre_DDR_clock_init, Delta
D - 0 - sbl1_ddr_set_params, Delta
B - 346724 - do ddr sanity test, Start
D - 335 - do ddr sanity test, Delta
B - 352854 - pm_driver_init, Start
B - 359534 - Manually set to USB500 mode
B - 360083 - raw vbat: 3939, gain: -19
B - 363895 - vbat: 3751
B - 366244 - Battery good, bootup
D - 13420 - pm_driver_init, Delta
B - 376583 - DDR Training restore, Start
B - 378596 - DDR Training restore, End
B - 388631 - clock_init, Start
D - 183 - clock_init, Delta
B - 388905 - Image Load, Start
D - 84668 - QSEE Image Loaded, Delta - (1528936 Bytes)
B - 473604 - Image Load, Start
D - 579 - SEC Image Loaded, Delta - (2048 Bytes)
B - 480863 - sbl1_efs_handle_cookies, Start
D - 884 - sbl1_efs_handle_cookies, Delta
B - 488732 - Image Load, Start
D - 11620 - DEVCFG Image Loaded, Delta - (32444 Bytes)
B - 500810 - Image Load, Start
D - 19825 - RPM Image Loaded, Delta - (169840 Bytes)
B - 520665 - Image Load, Start
D - 53131 - APPSBL Image Loaded, Delta - (572240 Bytes)
B - 573827 - QSEE Execution, Start
D - 61 - QSEE Execution, Delta
B - 579530 - USB D+ check, Start
B - 694912 - usb:: dcp
D - 112148 - USB D+ check, Delta
B - 694942 - SBL1, End
D - 474458 - SBL1, Delta
S - Flash Throughput, 28000 KB/s (2308604 Bytes, 79718 us)
S - DDR Frequency, 931 MHz
S - Core 0 Frequency, 800 MHz
Android Bootloader - UART_DM Initialized!!!
[0] welcome to lk

[10] platform_init()
[10] target_init()
[30] SDHC Running in HS400 mode
[40] Done initialization of the card
[40] pm8x41_get_is_cold_boot: cold boot
[40] Qseecom Init Done in Appsbl
[50] secure app region addr=0x85b00000 size=0x800000[50] TZ App region notif returned with status:0 addr:85b00000 size:8388608
[60] TZ App log region register returned with status:0 addr:8f6a8000 size:4096
[60] Qseecom TZ Init Done in Appsbl
[80] Loading cmnlib done
[80] qseecom_start_app: Loading app keymaster for the first time’
[100] <8>keymaster: “\”KEYMASTER Init \””
[100] Waiting for the RPM to populate smd channel table
[110] Not able to search the panel:
[110] panel_operating_mode=0x0
[190] chip serial splash =-1330649341
[190] chip serial pinfo =-1330649341
[190] Found stored PLL codes!
[200] ERROR: Splash image header invalid
[250] Config MIPI_VIDEO_PANEL.
[390] dsi panel init error
[400] Turn off MIPI_VIDEO_PANEL.
[600] Not able to search the panel:
[600] panel_operating_mode=0x0
[730] chip serial splash =-1330649341
[730] chip serial pinfo =-1330649341
[730] Found stored PLL codes!
[740] ERROR: Splash image header invalid
[800] Config MIPI_VIDEO_PANEL.
[940] Turn on MIPI_VIDEO_PANEL.
[960] Video lane tested successfully
[960] pm8x41_get_is_cold_boot: cold boot
[960] Unable to locate /bootselect partition
[970] boot_verifier: Device is in ORANGE boot state.
[970] Device is unlocked! Skipping verification…
[980] Loading (boot) image (25868288): start
[1060] Loading (boot) image (25868288): done
[1070] use_signed_kernel=1, is_unlocked=1, is_tampered=0.
[1140] creating boot verify keys detect thread
[6250] ERROR: Splash image header invalid
[6310] LK SEC APP Handle: 0x1
[6320] <8>keymaster: “\”cmd_id=KEYMASTER_SET_ROT\””
[6320] LK SEC APP Handle: 0x1
[6320] <8>keymaster: “\”cmd_id=KEYMASTER_GET_VERSION\””
[6330] Authentication Key not yet programmed
[6330] <8>keymaster: “\”QSEE_STOR_RPMB_NOT_PROVISIONED\””
[6340] decompressing kernel image: start
[6910] decompressing kernel image: done
[6930] Best match DTB tags 338/0000000b/0x00000000/0/10016/20011/0/0/a16cdc85/43210
[6940] Using pmic info 0x10016/0x20011/0x0/0x0 for device 0x10016/0x20011/0x0/0x0
[6950] display kernel cmdline: mdss_mdp.panel=1:dsi:0:qcom,mdss_dsi_hx8399c_fhd_video:1:none:cfg:single_dsi
[6950] cmdline: console=ttyHSL0,115200,n8 androidboot.console=ttyHSL0 androidboot.hardware=qcom msm_rtb.filter=0x237 ehci-hcd.park=3 lpm_levels.sleep_disabled=1 androidboot.bootdevice=7824900.sdhci earlycon=msm_hsl_uart,0x78af000 buildvariant=userdebug androidbo[6980] Updating device tree: start
[7150] Updating device tree: done
[7150] Turn off MIPI_VIDEO_PANEL.
[7150] Continuous splash enabled, keeping panel alive.
[7160] <8>keymaster: “\”cmd_id=KEYMASTER_MILESTONE_CALL\””
[7160] Qseecom De-Init Done in Appsbl
[7170] Channel alloc freed
[7180] booting linux @ 0x10080000, ramdisk @ 0x13600000 (2056240), tags/device tree @ 0x13400000
[7180] Jumping to kernel via monitor
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 3.18.31-g27d91ba-dirty (ubuntu@ubuntu) (gcc version 4.9 20150123 (prerelease) (GCC) ) #8 SMP PREEMPT Wed Jul 12 11:20:27 CST 2017
[ 0.000000] CPU: AArch64 Processor [410fd034] revision 4
[ 0.000000] alternatives: enabling workaround for ARM erratum 845719
[ 0.000000] Machine: Qualcomm Technologies, Inc. SDM450 MTP
[ 0.000000] Early serial console at I/O port 0x0 (options ”)
[ 0.000000] bootconsole [uart0] enabled
[ 0.000000] efi: Getting EFI parameters from FDT:
[ 0.000000] efi: UEFI not found.
[ 0.000000] Reserved memory: reserved region for node ‘other_ext_region@0’: base 0x0000000085b00000, size 13 MiB
[ 0.000000] Reserved memory: reserved region for node ‘modem_region@0’: base 0x0000000086c00000, size 106 MiB
[ 0.000000] Reserved memory: reserved region for node ‘adsp_fw_region@0’: base 0x000000008d600000, size 17 MiB
[ 0.000000] Reserved memory: reserved region for node ‘wcnss_fw_region@0’: base 0x000000008e700000, size 7 MiB
[ 0.000000] Reserved memory: reserved region for node ‘dfps_data_mem@90000000’: base 0x0000000090000000, size 0 MiB
[ 0.000000] Reserved memory: reserved region for node ‘splash_region@0x90001000’: base 0x0000000090001000, size 19 MiB
[ 0.000000] Removed memory: created DMA memory pool at 0x0000000085b00000, size 13 MiB
[ 0.000000] Reserved memory: initialized node other_ext_region@0, compatible id removed-dma-pool
[ 0.000000] Removed memory: created DMA memory pool at 0x0000000086c00000, size 106 MiB
[ 0.000000] Reserved memory: initialized node modem_region@0, compatible id removed-dma-pool
[ 0.000000] Removed memory: created DMA memory pool at 0x000000008d600000, size 17 MiB
[ 0.000000] Reserved memory: initialized node adsp_fw_region@0, compatible id removed-dma-pool
[ 0.000000] Removed memory: created DMA memory pool at 0x000000008e700000, size 7 MiB
[ 0.000000] Reserved memory: initialized node wcnss_fw_region@0, compatible id removed-dma-pool
[ 0.000000] Reserved memory: allocated memory for ‘venus_region@0’ node: base 0x000000008f800000, size 8 MiB
[ 0.000000] Reserved memory: created CMA memory pool at 0x000000008f800000, size 8 MiB
[ 0.000000] Reserved memory: initialized node venus_region@0, compatible id shared-dma-pool
[ 0.000000] Reserved memory: allocated memory for ‘secure_region@0’ node: base 0x00000000f6800000, size 152 MiB
[ 0.000000] Reserved memory: created CMA memory pool at 0x00000000f6800000, size 152 MiB
[ 0.000000] Reserved memory: initialized node secure_region@0, compatible id shared-dma-pool
[ 0.000000] Reserved memory: allocated memory for ‘qseecom_region@0’ node: base 0x00000000f5800000, size 16 MiB
[ 0.000000] Reserved memory: created CMA memory pool at 0x00000000f5800000, size 16 MiB
[ 0.000000] Reserved memory: initialized node qseecom_region@0, compatible id shared-dma-pool
[ 0.000000] Reserved memory: allocated memory for ‘adsp_region@0’ node: base 0x00000000f5400000, size 4 MiB
[ 0.000000] Reserved memory: created CMA memory pool at 0x00000000f5400000, size 4 MiB
[ 0.000000] Reserved memory: initialized node adsp_region@0, compatible id shared-dma-pool
[ 0.000000] Reserved memory: allocated memory for ‘gpu_region@0’ node: base 0x000000008f000000, size 8 MiB
[ 0.000000] Reserved memory: created CMA memory pool at 0x000000008f000000, size 8 MiB
[ 0.000000] Reserved memory: initialized node gpu_region@0, compatible id shared-dma-pool
[ 0.000000] cma: Reserved 40 MiB at 0x00000000f2c00000
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.0 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: Initializing psci_cpu_init
[ 0.000000] psci: Initializing psci_cpu_init
[ 0.000000] psci: Initializing psci_cpu_init
[ 0.000000] psci: Initializing psci_cpu_init
[ 0.000000] psci: Initializing psci_cpu_init
[ 0.000000] psci: Initializing psci_cpu_init
[ 0.000000] psci: Initializing psci_cpu_init
[ 0.000000] PERCPU: Embedded 15 pages/cpu @ffffffc0e22c7000 s22592 r8192 d30656 u61440
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 931328
[ 0.000000] Kernel command line: sched_enable_hmp=1 sched_enable_power_aware=1 console=ttyHSL0,115200,n8 androidboot.console=ttyHSL0 androidboot.hardware=qcom msm_rtb.filter=0x237 ehci-hcd.park=3 lpm_levels.sleep_disabled=1 androidboot.bootdevice=7824900.sdhci earlycon=msm_hsl_uart,0x78af000 buildvariant=userdebug androidboot.emmc=true androidboot.verifiedbootstate=orange androidboot.veritymode=enforcing androidboot.keymaster=1 androidboot.serialno=2cafacf7 androidboot.baseband=msm mdss_mdp.panel=1:dsi:0:qcom,mdss_dsi_hx8399c_fhd_video:1:none:cfg:single_dsi
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.000000] Memory: 3302668K/3894272K available (14540K kernel code, 2943K rwdata, 7868K rodata, 1180K init, 4283K bss, 591604K reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vmalloc : 0xffffff8000000000 - 0xffffffba3fff0000 ( 232 GB)
[ 0.000000] vmemmap : 0xffffffba40000000 - 0xffffffbfc0000000 ( 22 GB maximum)
[ 0.000000] 0xffffffba40b00000 - 0xffffffba4b000000 ( 165 MB actual)
[ 0.000000] PCI I/O : 0xffffffbffa000000 - 0xffffffbffb000000 ( 16 MB)
[ 0.000000] fixed : 0xffffffbffbdfd000 - 0xffffffbffbdff000 ( 8 KB)
[ 0.000000] modules : 0xffffffbffc000000 - 0xffffffc000000000 ( 64 MB)
[ 0.000000] memory : 0xffffffc000000000 - 0xffffffc0f0000000 ( 3840 MB)
[ 0.000000] .init : 0xffffffc001665000 - 0xffffffc00178c000 ( 1180 KB)
[ 0.000000] .text : 0xffffffc000080000 - 0xffffffc0016642f4 ( 22417 KB)
[ 0.000000] .data : 0xffffffc0017a9000 - 0xffffffc001a88e00 ( 2944 KB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[ 0.000000] HMP scheduling enabled.
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] NR_IRQS:64 nr_irqs:64 0
[ 0.000000] mpm_init_irq_domain(): Cannot find irq controller for qcom,gpio-parent
[ 0.000000] MPM 1 irq mapping errored -517
[ 0.000000] Offload RCU callbacks from all CPUs
[ 0.000000] Offload RCU callbacks from CPUs: 0-7.
[ 0.000000] Architected cp15 and mmio timer(s) running at 19.20MHz (virt/virt).
[ 0.000007] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 3579139424256ns
[ 0.007995] Switched to clocksource arch_sys_counter
[ 0.014069] kmemleak: Kernel memory leak detector disabled
[ 0.018546] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=192000)
[ 0.028875] pid_max: default: 32768 minimum: 301
[ 0.034001] Security Framework initialized
[ 0.037546] SELinux: Initializing.
[ 0.041523] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.047784] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.058213] Initializing cgroup subsys freezer
[ 0.061719] Initializing cgroup subsys debug
[ 0.067565] /cpus/cpu@0: Missing clock-frequency property
[ 0.071991] /cpus/cpu@1: Missing clock-frequency property
[ 0.077317] /cpus/cpu@2: Missing clock-frequency property
[ 0.082728] /cpus/cpu@3: Missing clock-frequency property
[ 0.088109] /cpus/cpu@100: Missing clock-frequency property
[ 0.093643] /cpus/cpu@101: Missing clock-frequency property
[ 0.099224] /cpus/cpu@102: Missing clock-frequency property
[ 0.104758] /cpus/cpu@103: Missing clock-frequency property
[ 0.110392] hw perfevents: enabled with arm/armv8-pmuv3 PMU driver, 7 counters available
[ 0.118457] EFI services will not be available.
[ 0.123188] NOHZ: local_softirq_pending 02
[ 0.133460]
[ 0.133460] ************************************************
[ 0.140521] * NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE *
[ 0.146938] * *
[ 0.153472] * trace_printk() being used. Allocating extra memory. *
[ 0.159979] * *
[ 0.166469] * This means that this is a DEBUG kernel and it is *
[ 0.173000] * unsafe for produciton use. *
[ 0.179509] * *
[ 0.186000] * If you see this message and you are not debugging *
[ 0.192531] * the kernel, report this immediately to your vendor! *
[ 0.199041] * *
[ 0.205531] * NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE *
[ 0.212063] ************************************************
[ 0.252147] Core Debug Lock unlocked
[ 0.255644] MSM Memory Dump base table set up
[ 0.259181] MSM Memory Dump apps data table set up
[ 0.263862] Configuring XPU violations to be fatal errors
[ 0.272667] cpu_clock_pwr_init: Power clocks configured
[ 0.362217] Brought up 8 CPUs
[ 0.364153] SMP: Total of 8 processors activated.
[ 0.368979] alternatives: patching kernel code
[ 0.384393] DMI not present or invalid.
[ 0.546899] pinctrl core: initialized pinctrl subsystem
[ 0.553893] regulator-dummy: no parameters
[ 0.969585] NET: Registered protocol family 16
[ 0.984597] ————[ cut here ]————
[ 0.988223] WARNING: CPU: 0 PID: 1 at /media/1T_Code/Code/MOTO_SDM450/kernel/msm-3.18/drivers/power/qcom/pm-boot.c:45 msm_pm_boot_init+0x90/0xd0()
[ 1.001307] Modules linked in:
[ 1.004330] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.18.31-g27d91ba-dirty #8
[ 1.011615] Hardware name: Qualcomm Technologies, Inc. SDM450 MTP (DT)
[ 1.018126] Call trace:
[ 1.020565] [] dump_backtrace+0x0/0x270
[ 1.025942] [] show_stack+0x14/0x1c
[ 1.030979] [] dump_stack+0x80/0xa4
[ 1.036014] [] warn_slowpath_common+0x8c/0xb0
[ 1.041915] [] warn_slowpath_null+0x18/0x20
[ 1.047643] [] msm_pm_boot_init+0x90/0xd0
[ 1.053198] [] do_one_initcall+0x1a0/0x1bc
[ 1.058843] [] kernel_init_freeable+0x14c/0x1e8
[ 1.064919] [] kernel_init+0x14/0xd8
[ 1.070088] —[ end trace dde6d505d3d31be6 ]—
[ 1.074666] scm_call failed: func id 0x42000101, ret: -1, syscall returns: 0x0, 0x0, 0x0
[ 1.088119] cpuidle: using governor ladder
[ 1.108090] cpuidle: using governor menu
[ 1.128097] cpuidle: using governor qcom
[ 1.133508] vdso: 2 pages (1 code @ ffffffc0017b1000, 1 data @ ffffffc0017b0000)
[ 1.147735] software IO TLB [mem 0xe4c00000-0xe5000000] (4MB) mapped at [ffffffc0d4c00000-ffffffc0d4ffffff]
[ 1.167075] DMA: preallocated 256 KiB pool for atomic allocations
[ 1.192461] IPA HW is not supported on this target
[ 1.196218] IPA HW is not supported on this target
[ 1.201605] ipa_usb ipa3_usb_init:2690 exit: IPA_USB init success!
[ 1.207155] IPA HW is not supported on this target
[ 1.211959] IPA HW is not supported on this target
[ 1.230453] __of_mpm_init(): MPM driver mapping exists
[ 1.243685] platform soc:qcom,kgsl-hyp: assigned reserved memory node gpu_region@0
[ 1.333393] msm_mpm_dev_probe(): Cannot get clk resource for XO: -517
[ 1.353699] sps:sps is ready.
[ 1.360336] msm_thermal:vdd_restriction_reg_init Defer regulator vdd-dig probe
[ 1.366524] msm_thermal:probe_vdd_rstr Err regulator init. err:-517. KTM continues.
[ 1.374221] msm-thermal soc:qcom,msm-thermal: probe_vdd_rstr:Failed reading node=/soc/qcom,msm-thermal, key=qcom,max-freq-level. err=-517. KTM continues
[ 1.387822] msm_thermal:msm_thermal_dev_probe Failed reading node=/soc/qcom,msm-thermal, key=qcom,online-hotplug-core. err:-517
[ 1.406904] i2c-msm-v2 78b6000.i2c: probing driver i2c-msm-v2
[ 1.411935] i2c-msm-v2 78b6000.i2c: error on clk_get(core_clk):-517
[ 1.417873] i2c-msm-v2 78b6000.i2c: error probe() failed with err:-517
[ 1.426380] i2c-msm-v2 78b7000.i2c: probing driver i2c-msm-v2
[ 1.431347] i2c-msm-v2 78b7000.i2c: error on clk_get(core_clk):-517
[ 1.437345] i2c-msm-v2 78b7000.i2c: error probe() failed with err:-517
[ 1.445645] i2c-msm-v2 7af5000.i2c: probing driver i2c-msm-v2
[ 1.450597] i2c-msm-v2 7af5000.i2c: error on clk_get(core_clk):-517
[ 1.456610] i2c-msm-v2 7af5000.i2c: error probe() failed with err:-517
[ 1.468348] cpu-clock-8953 b114000.qcom,cpu-clock-8953: Speed bin: 6 PVS Version: 0
[ 1.475273] cpu-clock-8953 b114000.qcom,cpu-clock-8953: Get vdd-mx regulator!!!
[ 1.486453] msm_rpm_glink_dt_parse: qcom,rpm-glink compatible not matches
[ 1.492238] msm_rpm_dev_probe: APSS-RPM communication over SMD
[ 1.503207] smd_channel_probe_now: allocation table not initialized
[ 1.512528] smd_channel_probe_now: allocation table not initialized
[ 1.520818] smd_channel_probe_now: allocation table not initialized
[ 1.531096] msm_watchdog b017000.qcom,wdt: wdog absent resource not present
[ 1.537908] msm_watchdog b017000.qcom,wdt: MSM Watchdog Initialized
[ 1.547379] msm-jtag-fuse a601c.jtagfuse: JTag Fuse initialized
[ 1.571746] platform soc:qcom,adsprpc-mem: assigned reserved memory node adsp_region@0
[ 1.585610] spmi_pmic_arb 200f000.qcom,spmi: PMIC Arb Version-2 0x20010000
[ 1.604130] pm8953_s5: 400 <–> 1140 mV at 870 mV normal idle
[ 1.610888] pm8953_s5_avs_limit: 400 <–> 1140 mV
[ 1.615606] spm_regulator_probe: name=pm8953_s5, range=LV, voltage=870000 uV, mode=AUTO, step rate=1200 uV/us
[ 1.643148] platform 4080000.qcom,mss: assigned reserved memory node modem_region@0
[ 1.651111] platform c200000.qcom,lpass: assigned reserved memory node adsp_fw_region@0
[ 1.659070] platform 1de0000.qcom,venus: assigned reserved memory node venus_region@0
[ 1.667867] platform a21b000.qcom,pronto: assigned reserved memory node wcnss_fw_region@0
[ 1.683065] apc_mem_acc_corner: 0 <–> 0 mV
[ 1.690276] cpr4_msm8953_apss_read_fuse_data: apc_corner: speed bin = 6
[ 1.695856] cpr4_msm8953_apss_read_fuse_data: apc_corner: CPR fusing revision = 3
[ 1.703350] cpr4_msm8953_apss_read_fuse_data: apc_corner: foundry id = 1
[ 1.710023] cpr4_msm8953_apss_read_fuse_data: apc_corner: CPR misc fuse value = 0
[ 1.717497] cpr4_msm8953_apss_read_fuse_data: apc_corner: Voltage boost fuse config = 0 boost = disable
[ 1.727092] cpr4_msm8953_apss_calculate_open_loop_voltages: apc_corner: fused LowSVS: open-loop= 625000 uV
[ 1.736673] cpr4_msm8953_apss_calculate_open_loop_voltages: apc_corner: fused SVS: open-loop= 680000 uV
[ 1.746479] cpr4_msm8953_apss_calculate_open_loop_voltages: apc_corner: fused NOM: open-loop= 785000 uV
[ 1.756287] cpr4_msm8953_apss_calculate_open_loop_voltages: apc_corner: fused TURBO_L1: open-loop= 915000 uV
[ 1.766209] cpr4_msm8953_apss_calculate_target_quotients: apc_corner: fused LowSVS: quot[ 7]= 561
[ 1.775129] cpr4_msm8953_apss_calculate_target_quotients: apc_corner: fused SVS: quot[ 7]= 649, quot_offset[ 7]= 85
[ 1.786063] cpr4_msm8953_apss_calculate_target_quotients: apc_corner: fused NOM: quot[ 7]= 862, quot_offset[ 7]= 210
[ 1.797001] cpr4_msm8953_apss_calculate_target_quotients: apc_corner: fused TURBO_L1: quot[ 7]=1116, quot_offset[ 7]= 250
[ 1.808613] cpr4_apss_init_aging: apc: sensor 6 aging init quotient diff = -4, aging RO scale = 2800 QUOT/V
[ 1.818016] cpr3_regulator_init_ctrl: apc: Default CPR mode = HW closed-loop
[ 1.825435] apc_corner: 0 <–> 0 mV at 0 mV
[ 1.834962] gfx_mem_acc_corner: 0 <–> 0 mV
[ 1.840490] GFX_LDO: msm_gfx_ldo_parse_dt: Unable to parse CX parameters rc=-517
[ 1.846847] GFX_LDO: msm_gfx_ldo_probe: Unable to pasrse dt rc=-517
[ 1.906424] msm_mpm_dev_probe(): Cannot get clk resource for XO: -517
[ 1.913094] msm_thermal:sensor_mgr_init_threshold threshold id already initialized
[ 1.919904] msm_thermal:vdd_restriction_reg_init Defer regulator vdd-dig probe
[ 1.926832] msm_thermal:probe_vdd_rstr Err regulator init. err:-517. KTM continues.
[ 1.934502] msm-thermal soc:qcom,msm-thermal: probe_vdd_rstr:Failed reading node=/soc/qcom,msm-thermal, key=qcom,max-freq-level. err=-517. KTM continues
[ 1.948127] msm_thermal:msm_thermal_dev_probe Failed reading node=/soc/qcom,msm-thermal, key=qcom,online-hotplug-core. err:-517
[ 1.960629] i2c-msm-v2 78b6000.i2c: probing driver i2c-msm-v2
[ 1.965615] i2c-msm-v2 78b6000.i2c: error on clk_get(core_clk):-517
[ 1.971620] i2c-msm-v2 78b6000.i2c: error probe() failed with err:-517
[ 1.979199] i2c-msm-v2 78b7000.i2c: probing driver i2c-msm-v2
[ 1.984145] i2c-msm-v2 78b7000.i2c: error on clk_get(core_clk):-517
[ 1.990187] i2c-msm-v2 78b7000.i2c: error probe() failed with err:-517
[ 1.997726] i2c-msm-v2 7af5000.i2c: probing driver i2c-msm-v2
[ 2.002689] i2c-msm-v2 7af5000.i2c: error on clk_get(core_clk):-517
[ 2.008713] i2c-msm-v2 7af5000.i2c: error probe() failed with err:-517
[ 2.016043] cpu-clock-8953 b114000.qcom,cpu-clock-8953: Speed bin: 6 PVS Version: 0
[ 2.023119] cpu-clock-8953 b114000.qcom,cpu-clock-8953: Get vdd-mx regulator!!!
[ 2.030453] msm_rpm_glink_dt_parse: qcom,rpm-glink compatible not matches
[ 2.036898] msm_rpm_dev_probe: APSS-RPM communication over SMD
[ 2.045671] pm8953_s1: 870 <–> 1156 mV at 1000 mV normal idle
[ 2.054592] pm8953_s2_level: 0 <–> 0 mV at 0 mV normal idle
[ 2.062113] pm8953_s2_floor_level: 0 <–> 0 mV at 0 mV normal idle
[ 2.070282] pm8953_s2_level_ao: 0 <–> 0 mV at 0 mV normal idle
[ 2.079029] pm8953_s3: 1225 mV normal idle
[ 2.086069] pm8953_s4: 1900 <–> 2050 mV at 1900 mV normal idle
[ 2.094705] pm8953_s7_level: 0 <–> 0 mV at 0 mV normal idle
[ 2.102382] pm8953_s7_level_ao: 0 <–> 0 mV at 0 mV normal idle
[ 2.110309] pm8953_s7_level_so: 0 <–> 0 mV at 0 mV normal idle
[ 2.119025] pm8953_l1: 1000 mV normal idle
[ 2.126080] pm8953_l2: 975 <–> 1225 mV at 975 mV normal idle
[ 2.134443] pm8953_l3: 925 mV normal idle
[ 2.141715] pm8953_l5: 1800 mV normal idle
[ 2.148536] pm8953_l6: 1800 mV normal idle
[ 2.155565] pm8953_l7: 1800 <–> 1900 mV at 1800 mV normal idle
[ 2.163468] pm8953_l7_ao: 1800 <–> 1900 mV at 1800 mV normal idle
[ 2.172540] pm8953_l8: 2900 mV normal idle
[ 2.179414] pm8953_l9: 3000 <–> 3300 mV at 3000 mV normal idle
[ 2.188270] pm8953_l10: 2800 mV normal idle
[ 2.195245] pm8953_l11: 2950 mV normal idle
[ 2.202410] pm8953_l12: 1800 <–> 2950 mV at 1800 mV normal idle
[ 2.211430] pm8953_l13: 3125 mV normal idle
[ 2.218468] pm8953_l16: 1800 mV normal idle
[ 2.225543] pm8953_l17: 2850 mV normal idle
[ 2.232502] pm8953_l19: 1200 <–> 1350 mV at 1200 mV normal idle
[ 2.241587] pm8953_l22: 2800 mV normal idle
[ 2.248510] pm8953_l23: 975 <–> 1225 mV at 975 mV normal idle
[ 2.256078] GFX_LDO: msm_gfx_ldo_voltage_init: LDO corner 1: target-volt = 580000 uV
[ 2.262813] GFX_LDO: msm_gfx_ldo_voltage_init: LDO corner 2: target-volt = 650000 uV
[ 2.270528] GFX_LDO: msm_gfx_ldo_voltage_init: LDO corner 3: target-volt = 720000 uV
[ 2.278270] GFX_LDO: msm_gfx_ldo_adjust_init_voltage: adjusted the open-loop voltage[1] 580000 -> 615000
[ 2.287695] GFX_LDO: msm_gfx_ldo_adjust_init_voltage: adjusted the open-loop voltage[2] 650000 -> 675000
[ 2.297179] GFX_LDO: msm_gfx_ldo_voltage_init: LDO-mode fuse disabled by default
[ 2.305950] msm_gfx_ldo: 0 <–> 0 mV at 0 mV
[ 2.310713] msm_mpm_dev_probe(): Cannot get clk resource for XO: -517
[ 2.317358] msm_thermal:sensor_mgr_init_threshold threshold id already initialized
[ 2.325278] cpu cpu0: dev_pm_opp_get_opp_count: device OPP not found (-19)
[ 2.331141] msm_thermal:get_cpu_freq_plan_len Error reading CPU0 freq table len. error:-19
[ 2.339383] cpu cpu4: dev_pm_opp_get_opp_count: device OPP not found (-19)
[ 2.346218] msm_thermal:get_cpu_freq_plan_len Error reading CPU4 freq table len. error:-19
[ 2.354481] msm_thermal:vdd_restriction_reg_init Defer vdd rstr freq init.
[ 2.364783] cpu cpu0: dev_pm_opp_get_opp_count: device OPP not found (-19)
[ 2.365534] i2c-msm-v2 78b6000.i2c: probing driver i2c-msm-v2
[ 2.365847] i2c-msm-v2 78b6000.i2c: error on clk_get(core_clk):-517
[ 2.365863] i2c-msm-v2 78b6000.i2c: error probe() failed with err:-517
[ 2.367031] i2c-msm-v2 78b7000.i2c: probing driver i2c-msm-v2
[ 2.367275] i2c-msm-v2 78b7000.i2c: error on clk_get(core_clk):-517
[ 2.367290] i2c-msm-v2 78b7000.i2c: error probe() failed with err:-517
[ 2.368445] i2c-msm-v2 7af5000.i2c: probing driver i2c-msm-v2
[ 2.368689] i2c-msm-v2 7af5000.i2c: error on clk_get(core_clk):-517
[ 2.368704] i2c-msm-v2 7af5000.i2c: error probe() failed with err:-517
[ 2.426125] msm_thermal:get_cpu_freq_plan_len Error reading CPU0 freq table len. error:-19
[ 2.434387] cpu cpu4: dev_pm_opp_get_opp_count: device OPP not found (-19)
[ 2.441215] msm_thermal:get_cpu_freq_plan_len Error reading CPU4 freq table len. error:-19
[ 2.449469] cpu cpu0: dev_pm_opp_get_opp_count: device OPP not found (-19)
[ 2.456296] msm_thermal:get_cpu_freq_plan_len Error reading CPU0 freq table len. error:-19
[ 2.464574] cpu cpu4: dev_pm_opp_get_opp_count: device OPP not found (-19)
[ 2.471420] msm_thermal:get_cpu_freq_plan_len Error reading CPU4 freq table len. error:-19
[ 2.471563] ————[ cut here ]————
[ 2.471589] WARNING: CPU: 2 PID: 6 at /media/1T_Code/Code/MOTO_SDM450/kernel/msm-3.18/drivers/clk/msm/clock-local2.c:1005 branch_clk_handoff+0xd8/0x120()
[ 2.471593] gcc_usb_phy_cfg_ahb_clk clock is enabled in HW even though ENABLE_BIT is not set
[ 2.471600] Modules linked in:
[ 2.471611] CPU: 2 PID: 6 Comm: kworker/u16:0 Tainted: G W 3.18.31-g27d91ba-dirty #8
[ 2.471615] Hardware name: Qualcomm Technologies, Inc. SDM450 MTP (DT)
[ 2.471632] Workqueue: deferwq deferred_probe_work_func
[ 2.471636] Call trace:
[ 2.471647] [] dump_backtrace+0x0/0x270
[ 2.471656] [] show_stack+0x14/0x1c
[ 2.471667] [] dump_stack+0x80/0xa4
[ 2.471677] [] warn_slowpath_common+0x8c/0xb0
[ 2.471686] [] warn_slowpath_fmt+0x60/0x80
[ 2.471694] [] branch_clk_handoff+0xd8/0x120
[ 2.471702] [] __handoff_clk+0xc8/0x2e8
[ 2.471709] [] msm_clock_register+0x188/0x248
[ 2.471716] [] of_msm_clock_register+0x88/0x98
[ 2.471725] [] msm_gcc_probe+0x178/0x26c
[ 2.471735] [] platform_drv_probe+0x38/0x84
[ 2.471743] [] driver_probe_device+0x164/0x370
[ 2.471750] [] __device_attach+0x2c/0x4c
[ 2.471757] [] bus_for_each_drv+0x7c/0xac
[ 2.471764] [] device_attach+0x70/0x9c
[ 2.471771] [] bus_probe_device+0x2c/0xa0
[ 2.471778] [] deferred_probe_work_func+0x98/0xc8
[ 2.471789] [] process_one_work+0x254/0x444
[ 2.471797] [] worker_thread+0x2fc/0x418
[ 2.471806] [] kthread+0xf0/0xf8
[ 2.471810] —[ end trace dde6d505d3d31be7 ]—
[ 2.481381] qcom,gcc-8953 1800000.qcom,gcc: Registered GCC clocks
[ 2.481943] cpu-clock-8953 b114000.qcom,cpu-clock-8953: Speed bin: 6 PVS Version: 0
[ 2.487268] cpr3_regulator_measure_aging: apc: average quotient delta=-8 (count=10)
[ 2.487304] cpr3_regulator_aging_adjust: apc: aging measurement successful; aging reference adjustment voltage=0 uV
[ 2.493121] cpu-clock-8953 b114000.qcom,cpu-clock-8953: missing qcom,dfs-sid-c0
[ 2.493130] cpu-clock-8953 b114000.qcom,cpu-clock-8953: No DFS SID tables found for Cluster-0
[ 2.493139] cpu-clock-8953 b114000.qcom,cpu-clock-8953: missing qcom,link-sid-c0
[ 2.493146] cpu-clock-8953 b114000.qcom,cpu-clock-8953: No Link SID tables found for Cluster-0
[ 2.493155] cpu-clock-8953 b114000.qcom,cpu-clock-8953: missing qcom,lmh-sid-c0
[ 2.493162] cpu-clock-8953 b114000.qcom,cpu-clock-8953: No LMH SID tables found for Cluster-0
[ 2.493165] ramp_lmh_sid: Use Default LMH SID
[ 2.493169] ramp_dfs_sid: Use Default DFS SID
[ 2.493172] ramp_link_sid: Use Default Link SID
[ 2.493272] cpu-clock-8953 b114000.qcom,cpu-clock-8953: missing qcom,dfs-sid-c1
[ 2.493279] cpu-clock-8953 b114000.qcom,cpu-clock-8953: No DFS SID tables found for Cluster-1
[ 2.493288] cpu-clock-8953 b114000.qcom,cpu-clock-8953: missing qcom,link-sid-c1
[ 2.493295] cpu-clock-8953 b114000.qcom,cpu-clock-8953: No Link SID tables found for Cluster-1
[ 2.493304] cpu-clock-8953 b114000.qcom,cpu-clock-8953: missing qcom,lmh-sid-c1
[ 2.493310] cpu-clock-8953 b114000.qcom,cpu-clock-8953: No LMH SID tables found for Cluster-1
[ 2.493314] ramp_lmh_sid: Use Default LMH SID
[ 2.493317] ramp_dfs_sid: Use Default DFS SID
[ 2.493319] ramp_link_sid: Use Default Link SID
[ 2.493503] clock_rcgwr_init: RCGwR Init Completed
[ 2.494856] populate_opp_table: clock-cpu-8953: OPP tables populated (cpu 3 and 7)
[ 2.494862] print_opp_table: clock_cpu: a53 C0: OPP voltage for 652800000: 1
[ 2.494867] print_opp_table: clock_cpu: a53 C0: OPP voltage for 1804800000: 5
[ 2.494871] print_opp_table: clock_cpu: a53 C1: OPP voltage for 652800000: 1
[ 2.494876] print_opp_table: clock_cpu: a53 C2: OPP voltage for 1804800000: 5
[ 2.497857] i2c-msm-v2 78b6000.i2c: probing driver i2c-msm-v2
[ 2.498299] AXI: msm_bus_scale_register_client(): msm_bus_scale_register_client: Bus driver not ready.
[ 2.498300] i2c-msm-v2 78b6000.i2c: msm_bus_scale_register_client(mstr-id:86):0 (not a problem)
[ 2.501022] kworker/u16:2 (101) used greatest stack depth: 13448 bytes left
[ 2.508985] i2c-msm-v2 78b7000.i2c: probing driver i2c-msm-v2
[ 2.509510] AXI: msm_bus_scale_register_client(): msm_bus_scale_register_client: Bus driver not ready.
[ 2.509510] i2c-msm-v2 78b7000.i2c: msm_bus_scale_register_client(mstr-id:86):0 (not a problem)
[ 2.510167] i2c-msm-v2 78b7000.i2c: irq:176 when no active transfer
[ 2.516139] i2c-msm-v2 7af5000.i2c: probing driver i2c-msm-v2
[ 2.516653] AXI: msm_bus_scale_register_client(): msm_bus_scale_register_client: Bus driver not ready.
[ 2.516653] i2c-msm-v2 7af5000.i2c: msm_bus_scale_register_client(mstr-id:84):0 (not a problem)
[ 2.522919] gcc-gfx-8953 1800000.qcom,gcc-gfx: Registered GCC GFX clocks.
[ 2.975519] qcom,qpnp-pin qpnp-pin-16: qpnp_pin_probe: no device nodes specified in topology
[ 2.983003] qcom,qpnp-pin: probe of qpnp-pin-16 failed with error -22
[ 2.994762] gladiator_error_reporting b1c0000.qcom,msm-gladiator: MSM Gladiator Error Reporting Initialized
[ 3.004841] msm_cpuss_dump soc:cpuss_dump: Couldn’t get memory for dumping
[ 3.010717] msm_cpuss_dump soc:cpuss_dump: Couldn’t get memory for dumping
[ 3.029156] KPI: Bootloader start count = 26214
[ 3.032650] KPI: Bootloader end count = 261798
[ 3.037076] KPI: Bootloader display count = 57202
[ 3.041800] KPI: Bootloader load kernel count = 2783
[ 3.046713] KPI: Kernel MPM timestamp = 436439
[ 3.051161] KPI: Kernel MPM Clock frequency = 32768
[ 3.056032] socinfo_print: v0.10, id=338, ver=1.1, raw_id=154, raw_ver=0, hw_plat=11, hw_plat_ver=65536
[ 3.056032] accessory_chip=0, hw_plat_subtype=0, pmic_model=65558, pmic_die_revision=65536 foundry_id=2 serial_number=2964317955
[ 3.079754] eldo2_8953: no parameters
[ 3.083410] qpnp_pin_of_gpio_xlate: no such PMIC gpio 5 in device topology
[ 3.090091] adv_vreg: no parameters
[ 3.094464] vdd_vreg: no parameters
[ 3.099112] vgaarb: loaded
[ 3.105805] SCSI subsystem initialized
[ 3.111921] usbcore: registered new interface driver usbfs
[ 3.116794] usbcore: registered new interface driver hub
[ 3.122181] usbcore: registered new device driver usb
[ 3.129213] media: Linux media interface: v0.10
[ 3.133015] Linux video capture interface: v2.00
[ 3.137688] EDAC MC: Ver: 3.0.0
[ 3.158278] cpufreq: driver msm up and running
[ 3.163162] platform soc:qcom,ion:qcom,ion-heap@8: assigned reserved memory node secure_region@0
[ 3.171467] platform soc:qcom,ion:qcom,ion-heap@27: assigned reserved memory node qseecom_region@0
[ 3.181060] ION heap system created
[ 3.183758] ION heap mm created at 0x00000000f6800000 with size 9800000
[ 3.190158] ION heap qsecom created at 0x00000000f5800000 with size 1000000
[ 3.197853] msm_bus_fabric_init_driver
[ 3.203011] msm_bus_device 580000.ad-hoc-bus: Coresight support absent for bus: 2048
[ 3.241409] qcom,qpnp-power-on qpnp-power-on-1: PMIC@SID0 Power-on reason: Triggered from PON1 (secondary PMIC) and ‘cold’ boot
[ 3.251876] qcom,qpnp-power-on qpnp-power-on-1: PMIC@SID0: Unknown power-off reason
[ 3.260166] input: qpnp_pon as /devices/virtual/input/input0
[ 3.266387] pon_spare_reg: no parameters
[ 3.269674] qcom,qpnp-power-on qpnp-power-on-14: No PON config. specified
[ 3.276080] qcom,qpnp-power-on qpnp-power-on-14: PMIC@SID2 Power-on reason: Triggered from PON1 (secondary PMIC) and ‘cold’ boot
[ 3.287602] qcom,qpnp-power-on qpnp-power-on-14: PMIC@SID2: Unknown power-off reason
[ 3.295698] PMIC@SID0: (null) v1.0 options: 2, 2, 0, 0
[ 3.300607] PMIC@SID2: PMI8950 v2.0 options: 0, 0, 0, 0
[ 3.306949] ipa ipa2_uc_state_check:296 uC interface not initialized
[ 3.312276] ipa ipa_sps_irq_control_all:938 EP (2) not allocated.
[ 3.318342] ipa ipa_sps_irq_control_all:938 EP (5) not allocated.
[ 3.327141] sps:BAM 0x0000000007904000 is registered.
[ 3.332390] sps:BAM 0x0000000007904000 (va:0xffffff8001640000) enabled: ver:0x27, number of pipes:20
[ 3.354404] IPA driver initialization was successful.
[ 3.360373] gdsc_venus: no parameters
[ 3.364106] gdsc_mdss: no parameters
[ 3.367593] gdsc_jpeg: no parameters
[ 3.371350] gdsc_vfe: no parameters
[ 3.375045] gdsc_vfe1: no parameters
[ 3.378496] gdsc_cpp: no parameters
[ 3.382037] gdsc_oxili_gx: no parameters
[ 3.385097] gdsc_oxili_gx: supplied by msm_gfx_ldo
[ 3.390755] gdsc_venus_core0: fast normal
[ 3.394723] gdsc_oxili_cx: no parameters
[ 3.398738] gdsc_usb30: no parameters
[ 3.403189] mdss_pll_probe: MDSS pll label = MDSS DSI 0 PLL
[ 3.407725] mdss_pll_probe: mdss_pll_probe: label=MDSS DSI 0 PLL PLL SSC enabled
[ 3.417731] dsi_pll_clock_register_8996: Registered DSI PLL ndx=0 clocks successfully
[ 3.424657] mdss_pll_probe: MDSS pll label = MDSS DSI 1 PLL
[ 3.430092] mdss_pll_probe: mdss_pll_probe: label=MDSS DSI 1 PLL PLL SSC enabled
[ 3.438828] pll_is_pll_locked_8996: DSI PLL ndx=1 status=0 failed to Lock
[ 3.446570] dsi_pll_clock_register_8996: Registered DSI PLL ndx=1 clocks successfully
[ 3.454571] msm_iommu 1e00000.qcom,iommu: device apps_iommu (model: 500) mapped at ffffff8001c00000, with 21 ctx banks
[ 3.477152] msm_iommu_ctx 1e20000.qcom,iommu-ctx: context adsp_elf using bank 0
[ 3.483893] msm_iommu_ctx 1e21000.qcom,iommu-ctx: context adsp_sec_pixel using bank 1
[ 3.491635] msm_iommu_ctx 1e22000.qcom,iommu-ctx: context mdp_1 using bank 2
[ 3.498671] msm_iommu_ctx 1e23000.qcom,iommu-ctx: context venus_fw using bank 3
[ 3.506024] msm_iommu_ctx 1e24000.qcom,iommu-ctx: context venus_sec_non_pixel using bank 4
[ 3.514215] msm_iommu_ctx 1e25000.qcom,iommu-ctx: context venus_sec_bitstream using bank 5
[ 3.522526] msm_iommu_ctx 1e26000.qcom,iommu-ctx: context venus_sec_pixel using bank 6
[ 3.530381] msm_iommu_ctx 1e28000.qcom,iommu-ctx: context pronto_pil using bank 8
[ 3.537796] msm_iommu_ctx 1e29000.qcom,iommu-ctx: context q6 using bank 9
[ 3.544655] msm_iommu_ctx 1e2a000.qcom,iommu-ctx: context periph_rpm using bank 10
[ 3.552171] msm_iommu_ctx 1e2b000.qcom,iommu-ctx: context lpass using bank 11
[ 3.559320] msm_iommu_ctx 1e2f000.qcom,iommu-ctx: context adsp_io using bank 15
[ 3.566653] msm_iommu_ctx 1e30000.qcom,iommu-ctx: context adsp_opendsp using bank 16
[ 3.574319] msm_iommu_ctx 1e31000.qcom,iommu-ctx: context adsp_shared using bank 17
[ 3.581960] msm_iommu_ctx 1e32000.qcom,iommu-ctx: context cpp using bank 18
[ 3.588885] msm_iommu_ctx 1e33000.qcom,iommu-ctx: context jpeg_enc0 using bank 19
[ 3.596307] msm_iommu_ctx 1e34000.qcom,iommu-ctx: context vfe using bank 20
[ 3.603407] msm_iommu_ctx 1e35000.qcom,iommu-ctx: context mdp_0 using bank 21
[ 3.610476] msm_iommu_ctx 1e36000.qcom,iommu-ctx: context venus_ns using bank 22
[ 3.617773] msm_iommu_ctx 1e38000.qcom,iommu-ctx: context ipa using bank 24
[ 3.624766] msm_iommu_ctx 1e37000.qcom,iommu-ctx: context access_control using bank 23
[ 3.635593] /soc/qcom,cam_smmu/msm_cam_smmu_cb1: could not get #iommu-cells for /soc/qcom,iommu@1e00000
[ 3.644008] /soc/qcom,cam_smmu/msm_cam_smmu_cb3: could not get #iommu-cells for /soc/qcom,iommu@1e00000
[ 3.653347] /soc/qcom,cam_smmu/msm_cam_smmu_cb4: could not get #iommu-cells for /soc/qcom,iommu@1e00000
[ 3.666315] Advanced Linux Sound Architecture Driver Initialized.
[ 3.674569] Bluetooth: ffffffc07eebbd18
[ 3.677283] NET: Registered protocol family 31
[ 3.681808] Bluetooth: ffffffc07eebbd18
[ 3.685450] Bluetooth: ffffffc07eebbce8Bluetooth: ffffffc07eebbcb8
[ 3.691674] Bluetooth: ffffffc07eebbcd8[ 3.696280] cfg80211: Calling CRDA to update world regulatory domain
[ 3.701804] cfg80211: World regulatory domain updated:
[ 3.706873] cfg80211: DFS Master region: unset
[ 3.711241] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 3.720950] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 3.728933] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 3.736908] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 3.744906] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 3.752891] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 3.760878] cfg80211: (5490000 KHz - 5710000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 3.768863] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 3.776838] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ 3.785366] nfc: nfc_init: NFC Core ver 0.1
[ 3.789251] NET: Registered protocol family 39
[ 3.793551] pcie:pcie_init.
[ 3.804113] ibb_reg: 4600 <–> 6000 mV at 5500 mV
[ 3.808896] lab_reg: 4600 <–> 6000 mV at 5500 mV
[ 3.813546] Switched to clocksource arch_sys_counter
[ 3.982216] bcl_peripheral:bcl_perph_init BCL Initialized
[ 3.990548] NET: Registered protocol family 2
[ 3.995545] TCP established hash table entries: 32768 (order: 6, 262144 bytes)
[ 4.002787] TCP bind hash table entries: 32768 (order: 8, 1048576 bytes)
[ 4.008979] TCP: Hash tables configured (established 32768 bind 32768)
[ 4.015161] TCP: reno registered
[ 4.018440] UDP hash table entries: 2048 (order: 5, 196608 bytes)
[ 4.024540] UDP-Lite hash table entries: 2048 (order: 5, 196608 bytes)
[ 4.031564] NET: Registered protocol family 1
[ 4.040286] gcc-mdss-8953 1800000.qcom,gcc-mdss: Registered GCC MDSS clocks.
[ 4.047482] Trying to unpack rootfs image as initramfs…
[ 4.121816] Freeing initrd memory: 2008K (ffffffc003600000 - ffffffc0037f6000)
[ 4.137969] futex hash table entries: 2048 (order: 5, 131072 bytes)
[ 4.143257] Initialise system trusted keyring
[ 4.147689] audit: initializing netlink subsys (disabled)
[ 4.153105] audit: type=2000 audit(4.139:1): initialized
[ 4.163806] vmscan: error setting kswapd cpu affinity mask
[ 4.217413] zbud: loaded
[ 4.223231] VFS: Disk quotas dquot_6.5.2
[ 4.226673] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 4.244692] fuse init (API version 7.23)
[ 4.253795] Key type asymmetric registered
[ 4.256863] Asymmetric key parser ‘x509’ registered
[ 4.262488] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[ 4.269123] io scheduler noop registered
[ 4.273011] io scheduler deadline registered
[ 4.278296] io scheduler cfq registered (default)
[ 4.295172] i2c-msm-v2 78b6000.i2c: msm_bus_scale_register_client(mstr-id:86):0x2 (ok)
[ 4.302239] i2c-msm-v2 78b6000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:1 tx:1) mode:FIFO slv_addr:0x39 MSTR_STS:0x0d1300c8 OPER:0x00000010
[ 4.317802] msm_dba_helper_i2c_read: i2c read failed
[ 4.322724] adv7533_read: read err: addr 0x39, reg 0x0, size 0x1
[ 4.328709] adv7533_probe: Failed to read chip rev
[ 4.333608] adv7533: probe of 2-0039 failed with error -5
[ 4.339860] msm_dss_get_res_byname: ‘vbif_nrt_phys’ resource not found
[ 4.345370] mdss_mdp_probe+0x284/0x1420->msm_dss_ioremap_byname: ‘vbif_nrt_phys’ msm_dss_get_res_byname failed
[ 4.356296] mdss_mdp_irq_clk_register: unable to get clk: lut_clk
[ 4.362525] No change in context(0==0), skip
[ 4.366641] mdss_mdp_pipe_addr_setup: type:0 ftchid:-1 xinid:0 num:0 rect:0 ndx:0x1 prio:0
[ 4.374041] mdss_mdp_pipe_addr_setup: type:1 ftchid:-1 xinid:1 num:3 rect:0 ndx:0x8 prio:1
[ 4.382257] mdss_mdp_pipe_addr_setup: type:1 ftchid:-1 xinid:5 num:4 rect:0 ndx:0x10 prio:2
[ 4.390609] mdss_mdp_pipe_addr_setup: type:2 ftchid:-1 xinid:2 num:6 rect:0 ndx:0x40 prio:3
[ 4.398975] mdss_mdp_pipe_addr_setup: type:3 ftchid:-1 xinid:7 num:10 rect:0 ndx:0x400 prio:0
[ 4.407423] mdss_mdp_parse_dt_handler: Error from prop qcom,mdss-pipe-sw-reset-off : u32 array read
[ 4.416580] mdss_mdp_parse_dt_handler: Error from prop qcom,mdss-ib-factor-overlap : u32 array read
[ 4.426358] xlog_status: enable:1, panic:1, dump:2
[ 4.431982] mdss_mdp_probe: mdss version = 0x10100000, bootloader display is on, num 1, intf_sel=0x00000100
[ 4.445051] mdss_smmu_util_parse_dt_clock: clocks are not defined
[ 4.450324] mdss_smmu_probe: iommu v2 domain[0] mapping and clk register successful!
[ 4.457916] mdss_smmu_util_parse_dt_clock: clocks are not defined
[ 4.464064] mdss_smmu_probe: iommu v2 domain[2] mapping and clk register successful!
[ 4.476271] mdss_dsi_ctrl_probe: DSI Ctrl name = MDSS DSI CTRL->0
[ 4.482212] mdss_dsi_find_panel_of_node: cmdline:0:qcom,mdss_dsi_hx8399c_fhd_video:1:none:cfg:single_dsi panel_name:qcom,mdss_dsi_hx8399c_fhd_video
[ 4.494646] mdss_dsi_panel_init: Panel Name = hx8399c fhd video mode dsi panel
[ 4.501858] mdss_dsi_panel_timing_from_dt: found new timing “qcom,mdss_dsi_hx8399c_fhd_video” (ffffffc07eebb2e8)
[ 4.511916] mdss_dsi_parse_dcs_cmds: failed, key=qcom,mdss-dsi-post-panel-on-command
[ 4.519619] mdss_dsi_parse_dcs_cmds: failed, key=qcom,mdss-dsi-timing-switch-command
[ 4.527330] mdss_dsi_panel_get_dsc_cfg_np: cannot find dsc config node:
[ 4.534035] mdss_dsi_parse_panel_features: ulps feature disabled
[ 4.539931] mdss_dsi_parse_panel_features: ulps during suspend feature disabled
[ 4.547037] mdss_dsi_parse_dms_config: dynamic switch feature enabled: 0
[ 4.554075] 1a94000.qcom,mdss_dsi_ctrl0 supply vdd not found, using dummy regulator
[ 4.562401] mdss_dsi_parse_ctrl_params:3895 Unable to read qcom,display-id, data=0000000000000000,len=20
[ 4.571020] mdss_dsi_parse_gpio_params: bklt_en gpio not specified
[ 4.577213] msm_dss_get_res_byname: ‘dsi_phy_regulator’ resource not found
[ 4.584037] mdss_dsi_retrieve_ctrl_resources+0x170/0x254->msm_dss_ioremap_byname: ‘dsi_phy_regulator’ msm_dss_get_res_byname failed
[ 4.595833] mdss_dsi_retrieve_ctrl_resources: ctrl_base=ffffff8001672000 ctrl_size=400 phy_base=ffffff8001678400 phy_size=580
[ 4.607355] dsi_panel_device_register: Continuous splash enabled
[ 4.613696] mdss_register_panel: adding framebuffer device 1a94000.qcom,mdss_dsi_ctrl0
[ 4.623207] mdss_dsi_ctrl_probe: Dsi Ctrl->0 initialized, DSI rev:0x10040002, PHY rev:0x2
[ 4.630697] mdss_dsi_status_init: DSI status check interval:5000
[ 4.638786] mdss_register_panel: adding framebuffer device soc:qcom,mdss_wb_panel
[ 4.646763] mdss_fb_probe: fb0: split_mode:0 left:0 right:0
[ 4.654184] mdss_fb_register: FrameBuffer[0] 1080x2160 registered successfully!
[ 4.662013] mdss_fb_probe: fb1: split_mode:0 left:0 right:0
[ 4.667048] mdss_fb_register: FrameBuffer[1] 640x640 registered successfully!
[ 4.674043] mdss_mdp_splash_parse_dt: splash mem child node is not present
[ 4.683563] Gladiator Error Reporting not available
[ 4.688084] msm-dcc b3000.dcc: DCC XPU is not specified
[ 4.702894] IPC_RTR: msm_ipc_router_smd_driver_register Already driver registered IPCRTR
[ 4.710067] IPC_RTR: msm_ipc_router_smd_driver_register Already driver registered IPCRTR
[ 4.734917] In memshare_probe, Memshare probe success
[ 4.744243] msm_rpm_log_probe: OK
[ 4.752536] subsys-pil-tz soc:qcom,kgsl-hyp: for a506_zap segments only will be dumped.
[ 4.763399] subsys-pil-tz 1de0000.qcom,venus: for venus segments only will be dumped.
[ 4.778682] msm_serial_hs module loaded
[ 4.782176] msm_serial_hsl_probe: detected port #0 (ttyHSL0)
[ 4.787365] AXI: get_pdata(): Error: Client name not found
[ 4.792618] AXI: msm_bus_cl_get_pdata(): client has to provide missing entry for successful registration
[ 4.802064] msm_serial_hsl_probe: Bus scaling is disabled
[ 4.807739] 78af000.serial: ttyHSL0 at MMIO 0x78af000 (irq = 173, base_baud = 460800816089] msm_hsl_console_setup: console setup on port #0
[ 4.820660] console [ttyHSL0] enabled
[ 4.820660] console [ttyHSL0] enabled
[ 4.827908] bootconsole [uart0] disabled
[ 4.827908] bootconsole [uart0] disabled
[ 4.836996] msm_serial_hsl_init: driver initialized
[ 4.872488] platform 1c40000.qcom,kgsl-iommu:gfx3d_secure: assigned reserved memory node secure_region@0
[ 4.912954] brd: module loaded
[ 4.925806] loop: module loaded
[ 4.929655] zram: Created 1 device(s) …
[ 4.933682] QSEECOM: qseecom_probe: qseecom.qsee_version = 0x1000000
[ 4.939081] QSEECOM: qseecom_retrieve_ce_data: Device does not support PFE
[ 4.945677] QSEECOM: qseecom_probe: qseecom clocks handled by other subsystem
[ 4.952979] QSEECOM: qseecom_probe: qsee reentrancy support phase is not defined, setting to default 0
[ 4.963138] QSEECOM: qseecom_probe: qseecom.whitelist_support = 1
[ 4.974998] i2c-core: driver [tabla-i2c-core] using legacy suspend method
[ 4.980771] i2c-core: driver [tabla-i2c-core] using legacy resume method
[ 4.987800] i2c-core: driver [wcd9xxx-i2c-core] using legacy suspend method
[ 4.994383] i2c-core: driver [wcd9xxx-i2c-core] using legacy resume method
[ 5.001682] i2c-core: driver [tasha-i2c-core] using legacy suspend method
[ 5.008010] i2c-core: driver [tasha-i2c-core] using legacy resume method
[ 5.015713] PN547:pn547_dev_init: Loading pn547 driver
[ 5.020119] PN547:pn547_probe: pn547 enter probe
[ 5.024405] PN547:pn547_probe: nfc probe step02 is ok
[ 5.029464] PN547:pn547_probe: nfc probe step04 is ok
[ 5.034661] PN547:nfc_parse_dt: GPIO ven,irq,firm,clk_req = 89, 130, 1018
[ 5.041087] PN547:pn547_probe: irq_gpio=130, ven_gpio=89, firm_gpio=113
[ 5.047843] PN547:pn547_clock_select: nfc clk_src is BBCLK2
[ 5.053449] PN547:pn547_clock_select: pn547 clk_run = true
[ 5.058882] PN547:pn547_probe: pn547 clock select (0)
[ 5.064173] PN547:pn547_probe: nfc probe step05 is ok
[ 5.068987] PN547:pn547_probe: nfc probe GPIO is ok
[ 5.073799] PN547:pn547_probe: pn547 client->irq = 137
[ 5.078760] PN547:pn547_probe: pn547_probe : requesting IRQ 137
[ 5.084981] PN547:pn547_probe: nfc probe step06 is ok
[ 5.089871] PN547:pn547_probe: nfc probe successful
[ 5.095726] QCE50: __qce_get_device_tree_data: BAM Apps EE is not defined, setting to default 1
[ 5.105009] qce 720000.qcedev: Qualcomm Crypto 5.3.3 device found @0x720000
[ 5.110963] qce 720000.qcedev: CE device = 0x0
[ 5.110963] , IO base, CE = 0xffffff8001f40000
[ 5.110963] , Consumer (IN) PIPE 2, Producer (OUT) PIPE 3
[ 5.110963] IO base BAM = 0x (null)
[ 5.110963] BAM IRQ 193
[ 5.110963] Engines Availability = 0x2010853
[ 5.137506] sps:BAM 0x0000000000704000 is registered.
[ 5.141990] sps:BAM 0x0000000000704000 (va:0xffffff8002040000) enabled: ver:0x27, number of pipes:8
[ 5.151202] QCE50: qce_sps_init: Qualcomm MSM CE-BAM at 0x0000000000704000 irq 193
[ 5.162551] QCE50: __qce_get_device_tree_data: BAM Apps EE is not defined, setting to default 1
[ 5.172320] qcrypto 720000.qcrypto: Qualcomm Crypto 5.3.3 device found @0x720000
[ 5.178708] qcrypto 720000.qcrypto: CE device = 0x0
[ 5.178708] , IO base, CE = 0xffffff8002080000
[ 5.178708] , Consumer (IN) PIPE 4, Producer (OUT) PIPE 5
[ 5.178708] IO base BAM = 0x (null)
[ 5.178708] BAM IRQ 193
[ 5.178708] Engines Availability = 0x2010853
[ 5.205608] QCE50: qce_sps_init: Qualcomm MSM CE-BAM at 0x0000000000704000 irq 193
[ 5.214674] qcrypto 720000.qcrypto: qcrypto-ecb-aes
[ 5.218721] qcrypto 720000.qcrypto: qcrypto-cbc-aes
[ 5.223561] qcrypto 720000.qcrypto: qcrypto-ctr-aes
[ 5.228415] qcrypto 720000.qcrypto: qcrypto-ecb-des
[ 5.233293] qcrypto 720000.qcrypto: qcrypto-cbc-des
[ 5.238204] qcrypto 720000.qcrypto: qcrypto-ecb-3des
[ 5.243069] qcrypto 720000.qcrypto: qcrypto-cbc-3des
[ 5.248038] qcrypto 720000.qcrypto: qcrypto-xts-aes
[ 5.252881] qcrypto 720000.qcrypto: qcrypto-sha1
[ 5.257478] qcrypto 720000.qcrypto: qcrypto-sha256
[ 5.262266] qcrypto 720000.qcrypto: qcrypto-aead-hmac-sha1-cbc-aes
[ 5.268428] qcrypto 720000.qcrypto: qcrypto-aead-hmac-sha1-cbc-des
[ 5.274574] qcrypto 720000.qcrypto: qcrypto-aead-hmac-sha1-cbc-3des
[ 5.280840] qcrypto 720000.qcrypto: qcrypto-aead-hmac-sha256-cbc-aes
[ 5.287198] qcrypto 720000.qcrypto: qcrypto-aead-hmac-sha256-cbc-des
[ 5.293514] qcrypto 720000.qcrypto: qcrypto-aead-hmac-sha256-cbc-3des
[ 5.299937] qcrypto 720000.qcrypto: qcrypto-hmac-sha1
[ 5.304993] qcrypto 720000.qcrypto: qcrypto-hmac-sha256
[ 5.310179] qcrypto 720000.qcrypto: qcrypto-aes-ccm
[ 5.315025] qcrypto 720000.qcrypto: qcrypto-rfc4309-aes-ccm
[ 5.322525] qcom_ice_get_device_tree_data: No vdd-hba-supply regulator, assuming not needed
[ 5.330297] ICE IRQ = 194
[ 5.335874] SCSI Media Changer driver v0.25
[ 5.343483] tun: Universal TUN/TAP device driver, 1.6
[ 5.347490] tun: (C) 1999-2004 Max Krasnyansky [email protected]
[ 5.353996] PPP generic driver version 2.4.2
[ 5.358288] PPP BSD Compression module registered
[ 5.362606] PPP Deflate Compression module registered
[ 5.367661] PPP MPPE Compression module registered
[ 5.372433] NET: Registered protocol family 24
[ 5.378687] wcnss_wlan probed in built-in mode
[ 5.386121] usbcore: registered new interface driver asix
[ 5.390710] usbcore: registered new interface driver ax88179_178a
[ 5.396703] usbcore: registered new interface driver cdc_ether
[ 5.402524] usbcore: registered new interface driver net1080
[ 5.408189] usbcore: registered new interface driver cdc_subset
[ 5.414054] usbcore: registered new interface driver zaurus
[ 5.420024] usbcore: registered new interface driver cdc_ncm
[ 5.426280] msm_sharedmem: sharedmem_register_qmi: qmi init successful
[ 5.434802] scm_call failed: func id 0x42000c16, ret: -1, syscall returns: 0x0, 0x0, 0x0
[ 5.441897] hyp_assign_table: Failed to assign memory protection, ret = -5
[ 5.448732] msm_sharedmem: setup_shared_ram_perms: hyp_assign_phys failed IPA=0x0160x00000000f3200000 size=1572864 err=-5
[ 5.460225] msm_sharedmem: msm_sharedmem_probe: Device created for client ‘rmtfs’
[ 5.478640] msm-dwc3 7000000.ssusb: unable to get dbm device
[ 5.486862] ehci_hcd: USB 2.0 ‘Enhanced’ Host Controller (EHCI) Driver
[ 5.493220] ehci-pci: EHCI PCI platform driver
[ 5.496975] ehci-msm: Qualcomm On-Chip EHCI Host Controller
[ 5.503377] usbcore: registered new interface driver cdc_acm
[ 5.507989] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 5.516239] usbcore: registered new interface driver usb-storage
[ 5.522142] usbcore: registered new interface driver ums-alauda
[ 5.528011] usbcore: registered new interface driver ums-cypress
[ 5.533983] usbcore: registered new interface driver ums-datafab
[ 5.539981] usbcore: registered new interface driver ums-freecom
[ 5.545949] usbcore: registered new interface driver ums-isd200
[ 5.551863] usbcore: registered new interface driver ums-jumpshot
[ 5.557916] usbcore: registered new interface driver ums-karma
[ 5.563746] usbcore: registered new interface driver ums-sddr09
[ 5.569717] usbcore: registered new interface driver ums-sddr55
[ 5.575576] usbcore: registered new interface driver ums-usbat
[ 5.581707] usbcore: registered new interface driver usbserial
[ 5.587217] usbcore: registered new interface driver usb_ehset_test
[ 5.595275] gbridge_init: gbridge_init successs.
[ 5.600098] mousedev: PS/2 mouse device common for all mice
[ 5.605513] usbcore: registered new interface driver xpad
[ 5.611446] <<-GTP-INFO->> GTP driver installing…
[ 5.616358] <<-GTP-INFO->> GTP Driver Version: V2.4<2014/11/28>
[ 5.621250] <<-GTP-INFO->> GTP I2C Address: 0x5d
[ 5.627138] GTP INT IRQ ret=0GTP RST PORT ret=0<<-GTP-INFO->> Guitar reset
[ 5.758407] i2c-msm-v2 78b7000.i2c: msm_bus_scale_register_client(mstr-id:86):0xf (ok)
[ 5.765872] <<-GTP-INFO->> IC Version: 917D_400c
[ 5.771245] GTP sensor id 1
,<<-GTP-INFO->> Sensor_ID: 1
[ 5.775596] wsp Config group1 used,length: 228Config Version: 0, 0x00; IC Config Version: 65, 0x41<<-GTP-INFO->> Driver send config.
[ 5.787894] sps: BAM device 0x0000000007884000 is not registered yet.
[ 5.794944] sps:BAM 0x0000000007884000 is registered.
[ 5.799271] sps:BAM 0x0000000007884000 (va:0xffffff8001e20000) enabled: ver:0x19, number of pipes:12
[ 5.814206] GTP Driver send config err
[ 5.816911] <<-GTP-INFO->> X_MAX: 1080, Y_MAX: 2160, TRIGGER: 0x00
[ 5.838059] <<-GTP-INFO->> create proc entry gt9xx_config success
[ 5.843788] input: goodix-ts as /devices/virtual/input/input1
[ 5.849369] <<-GTP-INFO->> GTP works in interrupt mode.
[ 5.854050] <<-GTP-INFO->> Applied memory size:2562.
[ 5.859005] <<-GTP-INFO->> I2C function: without pre and end cmd!
[ 5.865068] ————[ cut here ]————
[ 5.869691] WARNING: CPU: 4 PID: 1 at /media/1T_Code/Code/MOTO_SDM450/kernel/msm-3.18/fs/proc/generic.c:330 __proc_create+0xac/0x1e0()
[ 5.881745] name len 0
[ 5.884076] Modules linked in:
[ 5.887118] CPU: 4 PID: 1 Comm: swapper/0 Tainted: G W 3.18.31-g27d91ba-dirty #8
[ 5.895535] Hardware name: Qualcomm Technologies, Inc. SDM450 MTP (DT)
[ 5.902045] Call trace:
[ 5.904480] [] dump_backtrace+0x0/0x270
[ 5.909860] [] show_stack+0x14/0x1c
[ 5.914896] [] dump_stack+0x80/0xa4
[ 5.919931] [] warn_slowpath_common+0x8c/0xb0
[ 5.925832] [] warn_slowpath_fmt+0x60/0x80
[ 5.931474] [] __proc_create+0xac/0x1e0
[ 5.936856] [] proc_create_data+0x70/0xc4
[ 5.942414] [] init_wr_node+0xe4/0x150
[ 5.947706] [] goodix_ts_probe+0x6a4/0x6d4
[ 5.953350] [] i2c_device_probe+0xdc/0x110
[ 5.958993] [] driver_probe_device+0x164/0x370
[ 5.964981] [] __driver_attach+0x64/0x90
[ 5.970450] [] bus_for_each_dev+0x80/0xb0
[ 5.976005] [] driver_attach+0x20/0x28
[ 5.981299] [] bus_add_driver+0x128/0x200
[ 5.986856] [] driver_register+0x94/0xe0
[ 5.992324] [] i2c_register_driver+0x4c/0xd0
[ 5.998143] [] goodix_ts_init+0x6c/0x74
[ 6.003522] [] do_one_initcall+0x1a0/0x1bc
[ 6.009166] [] kernel_init_freeable+0x14c/0x1e8
[ 6.015242] [] kernel_init+0x14/0xd8
[ 6.020419] —[ end trace dde6d505d3d31be8 ]—
[ 6.024962] <<-GTP-ERROR->> Couldn’t create proc entry!
[ 6.030286] [FTS]fts_ts_init: Enter
[ 6.033762] [FTS]fts_ts_probe: Enter
[ 6.037208] [FTS]fts_parse_dt: Enter
[ 6.040783] [FTS]3: (158, 102, 139), [160, 360, 570][2030]
[ 6.046241] [FTS]max_touch_number=10
[ 6.049802] [FTS]fts_parse_dt: Exit(952)
[ 6.053711] [FTS]Target does not use pinctrl -22
[ 6.053711]
[ 6.059806] [FTS]fts_input_dev_init: Enter
[ 6.063851] [FTS]set key capabilities
[ 6.068207] input: fts_ts as /devices/soc/78b7000.i2c/i2c-3/3-0038/input/input2
[ 6.075128] [FTS]fts_input_dev_init: Exit(253)
[ 6.079231] [FTS]fts_ctpm_get_upgrade_array: Enter
[ 6.083990] [FTS][Info]CHIP TYPE ID = 0x5422
[ 6.088393] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:3) mode:FIFO slv_addr:0x38 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 6.103996] [FTS][Error]fts_i2c_write: i2c_transfer(write) error, ret=-107
[ 6.128089] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:3 tx:0) mode:FIFO slv_addr:0x38 MSTR_STS:0x0d1300c8 OPER:0x00000010
[ 6.142814] [FTS][Error][IIC]: i2c_transfer(read) error, ret=-107!!
[ 6.149056] [FTS][Error]hidi2c change to stdi2c error!!
[ 6.154229] [FTS]fts_ctpm_get_upgrade_array: Exit(174)
[ 6.159396] [FTS]fts_gpio_configure: Enter
[ 6.163432] [FTS][Error][GPIO]irq gpio request failed
[ 6.168481] [FTS]fts_gpio_configure: Exit(796)
[ 6.172891] [FTS][Error][GPIO]Failed to configure the gpios
[ 6.208336] fts_ts: probe of 3-0038 failed with error -16
[ 6.212792] [FTS]fts_ts_init: Exit(1414)
[ 6.219271] input: hbtp_vm as /devices/virtual/input/input3
[ 6.224976] sx9310_init
[ 6.226507] zch sar—in sx9310_probe
[ 6.230726] 2-0028 supply vio not found, using dummy regulator
[ 6.268628] input: SX9310 Cap Touch as /devices/virtual/input/input4
[ 6.274655] sx9310 2-0028: registered with threaded irq (51)
[ 6.279750] i2c-msm-v2 78b6000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x28 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 6.295319] zch sar—report keycode = 645
[ 6.299389] sx9310 2-0028: Write_register-ForcetoTouched()
[ 6.608118] i2c-msm-v2 78b6000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x28 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 6.622827] zch sar—report keycode = 645
[ 6.626881] sx9310 2-0028: Write_register-ForcetoTouched()
[ 6.632428] i2c-msm-v2 78b6000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x28 MSTR_STS:0x091343c8 OPER:0x00000090
[ 6.648094] zch sar—report keycode = 645
[ 6.652143] sx9310 2-0028: Write_register-ForcetoTouched()
[ 6.657674] i2c-msm-v2 78b6000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x28 MSTR_STS:0x0d1343c8 OPER:0x00000090
[ 6.673351] zch sar—report keycode = 645
[ 6.677402] sx9310 2-0028: Write_register-ForcetoTouched()
[ 6.682946] i2c-msm-v2 78b6000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x28 MSTR_STS:0x091343c8 OPER:0x00000090
[ 6.698612] zch sar—report keycode = 645
[ 6.702662] sx9310 2-0028: Write_register-ForcetoTouched()
[ 6.708214] i2c-msm-v2 78b6000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x28 MSTR_STS:0x0d1343c8 OPER:0x00000090
[ 6.723873] zch sar—report keycode = 645
[ 6.727922] sx9310 2-0028: Write_register-ForcetoTouched()
[ 6.733498] i2c-msm-v2 78b6000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x28 MSTR_STS:0x091343c8 OPER:0x00000090
[ 6.749133] zch sar—report keycode = 645
[ 6.753183] sx9310 2-0028: Write_register-ForcetoTouched()
[ 6.758731] i2c-msm-v2 78b6000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x28 MSTR_STS:0x0d1343c8 OPER:0x00000090
[ 6.774393] zch sar—report keycode = 645
[ 6.778477] sx9310 2-0028: Write_register-ForcetoTouched()
[ 6.783977] i2c-msm-v2 78b6000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x28 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 6.799655] zch sar—report keycode = 645
[ 6.803704] sx9310 2-0028: Write_register-ForcetoTouched()
[ 6.809251] i2c-msm-v2 78b6000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x28 MSTR_STS:0x0d1343c8 OPER:0x00000090
[ 6.824909] zch sar—report keycode = 645
[ 6.828977] sx9310 2-0028: Write_register-ForcetoTouched()
[ 6.834496] i2c-msm-v2 78b6000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x28 MSTR_STS:0x0d1343c8 OPER:0x00000090
[ 6.850170] zch sar—report keycode = 645
[ 6.854223] sx9310 2-0028: Write_register-ForcetoTouched()
[ 6.859772] i2c-msm-v2 78b6000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x28 MSTR_STS:0x0d1343c8 OPER:0x00000090
[ 6.875430] zch sar—report keycode = 645
[ 6.879499] sx9310 2-0028: Write_register-ForcetoTouched()
[ 6.885017] i2c-msm-v2 78b6000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x28 MSTR_STS:0x091343c8 OPER:0x00000090
[ 6.900693] zch sar—report keycode = 645
[ 6.904746] sx9310 2-0028: Write_register-ForcetoTouched()
[ 6.910316] i2c-msm-v2 78b6000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x28 MSTR_STS:0x091343c8 OPER:0x00000090
[ 6.925947] zch sar—report keycode = 645
[ 6.930017] sx9310 2-0028: Write_register-ForcetoTouched()
[ 6.935537] i2c-msm-v2 78b6000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x28 MSTR_STS:0x091343c8 OPER:0x00000090
[ 6.951208] zch sar—report keycode = 645
[ 6.955265] sx9310 2-0028: Write_register-ForcetoTouched()
[ 6.960809] i2c-msm-v2 78b6000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x28 MSTR_STS:0x091343c8 OPER:0x00000090
[ 6.976468] zch sar—report keycode = 645
[ 6.980538] sx9310 2-0028: Write_register-ForcetoTouched()
[ 6.986058] i2c-msm-v2 78b6000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x28 MSTR_STS:0x091343c8 OPER:0x00000090
[ 7.001730] zch sar—report keycode = 645
[ 7.005787] sx9310 2-0028: Write_register-ForcetoTouched()
[ 7.011336] i2c-msm-v2 78b6000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x28 MSTR_STS:0x091343c8 OPER:0x00000090
[ 7.026988] zch sar—report keycode = 645
[ 7.031060] sx9310 2-0028: Write_register-ForcetoTouched()
[ 7.036578] i2c-msm-v2 78b6000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x28 MSTR_STS:0x091343c8 OPER:0x00000090
[ 7.052249] zch sar—report keycode = 645
[ 7.056308] sx9310 2-0028: Write_register-ForcetoTouched()
[ 7.061853] i2c-msm-v2 78b6000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x28 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 7.077510] zch sar—report keycode = 645
[ 7.081581] sx9310 2-0028: Write_register-ForcetoTouched()
[ 7.087100] i2c-msm-v2 78b6000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x28 MSTR_STS:0x091343c8 OPER:0x00000090
[ 7.102771] zch sar—report keycode = 645
[ 7.106828] sx9310 2-0028: Write_register-ForcetoTouched()
[ 7.112373] i2c-msm-v2 78b6000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x28 MSTR_STS:0x091343c8 OPER:0x00000090
[ 7.128041] zch sar—report keycode = 645
[ 7.132089] sx9310 2-0028: Write_register-ForcetoTouched()
[ 7.137621] i2c-msm-v2 78b6000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x28 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 7.153299] zch sar—report keycode = 645
[ 7.157349] sx9310 2-0028: Write_register-ForcetoTouched()
[ 7.162896] i2c-msm-v2 78b6000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x28 MSTR_STS:0x091343c8 OPER:0x00000090
[ 7.178558] zch sar—report keycode = 645
[ 7.182609] sx9310 2-0028: Write_register-ForcetoTouched()
[ 7.188158] i2c-msm-v2 78b6000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x28 MSTR_STS:0x0d1343c8 OPER:0x00000090
[ 7.203819] zch sar—report keycode = 645
[ 7.207871] sx9310 2-0028: Write_register-ForcetoTouched()
[ 7.213416] i2c-msm-v2 78b6000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x28 MSTR_STS:0x091343c8 OPER:0x00000090
[ 7.229080] zch sar—report keycode = 645
[ 7.233132] sx9310 2-0028: Write_register-ForcetoTouched()
[ 7.348089] i2c-msm-v2 78b6000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x28 MSTR_STS:0x091343c8 OPER:0x00000090
[ 7.362796] zch sar—report keycode = 645
[ 7.366852] sx9310 2-0028: Write_register-ForcetoTouched()
[ 7.372430] i2c-msm-v2 78b6000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:1 tx:1) mode:FIFO slv_addr:0x28 MSTR_STS:0x091343c8 OPER:0x00000010
[ 7.388104] create proc entry capsensor_enable successzch sar—sx9310_probe success
[ 7.395857] i2c-core: driver [sx9310] using legacy suspend method
[ 7.401849] i2c-core: driver [sx9310] using legacy resume method
[ 7.408395] 2-0053 supply vio not found, using dummy regulator
[ 7.414633] input: light as /devices/soc/78b6000.i2c/i2c-2/2-0053/input/input5
[ 7.421772] input: proximity as /devices/soc/78b6000.i2c/i2c-2/2-0053/input/input6
[ 7.429292] i2c-msm-v2 78b6000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:1 tx:1) mode:FIFO slv_addr:0x53 MSTR_STS:0x091343c8 OPER:0x00000010
[ 7.569890] LTR579 2-0053: ltr579_setup Turned on ambient light sensor
[ 7.628200] LTR579 2-0053: read_ps_adc_value: PS 149
[ 7.688195] LTR579 2-0053: read_ps_adc_value: PS 147
[ 7.718196] LTR579 2-0053: read_ps_adc_value: PS 148
[ 7.748197] LTR579 2-0053: read_ps_adc_value: PS 151
[ 7.778196] LTR579 2-0053: read_ps_adc_value: PS 147
[ 7.808196] LTR579 2-0053: read_ps_adc_value: PS 148
[ 7.812845] LTR579 2-0053: ltr579_setup Turned on proximity sensor
[ 7.818534] zch—in sensors_classdev_register
[ 7.823297] zch—sensors_classdev_register Registered sensors device: LTR579_ALS
[ 7.830209] zch—in sensors_classdev_register
[ 7.835178] zch—sensors_classdev_register Registered sensors device: LTR579_PS
[ 7.843943] qcom,qpnp-rtc qpnp-rtc-8: rtc core: registered qpnp_rtc as rtc0
[ 7.850335] i2c /dev entries driver
[ 7.865279] /soc/qcom,cam_smmu/msm_cam_smmu_cb1: could not get #iommu-cells for /soc/qcom,iommu@1e00000
[ 7.874592] /soc/qcom,cam_smmu/msm_cam_smmu_cb3: could not get #iommu-cells for /soc/qcom,iommu@1e00000
[ 7.883886] /soc/qcom,cam_smmu/msm_cam_smmu_cb4: could not get #iommu-cells for /soc/qcom,iommu@1e00000
[ 7.898427] msm_camera_get_dt_vreg_data qcom,cam-vreg-name count -22
[ 7.903735] msm_camera_get_dt_vreg_data:1115 number of entries is 0 or not present in dts
[ 7.916627] msm_camera_get_dt_vreg_data qcom,cam-vreg-name count -22
[ 7.921959] msm_camera_get_dt_vreg_data:1115 number of entries is 0 or not present in dts
[ 7.931622] msm_camera_get_dt_vreg_data qcom,cam-vreg-name count -22
[ 7.936928] msm_camera_get_dt_vreg_data:1115 number of entries is 0 or not present in dts
[ 7.946442] msm_camera_get_dt_vreg_data qcom,cam-vreg-name count -22
[ 7.951764] msm_camera_get_dt_vreg_data:1115 number of entries is 0 or not present in dts
[ 7.963097] msm_camera_get_dt_vreg_data qcom,cam-vreg-name count -22
[ 7.968426] msm_camera_get_dt_vreg_data:1115 number of entries is 0 or not present in dts
[ 7.978401] msm_camera_get_dt_vreg_data qcom,cam-vreg-name count -22
[ 7.983707] msm_camera_get_dt_vreg_data:1115 number of entries is 0 or not present in dts
[ 7.993681] msm_camera_get_dt_vreg_data qcom,cam-vreg-name count -22
[ 7.999004] msm_camera_get_dt_vreg_data:1115 number of entries is 0 or not present in dts
[ 8.008063] msm_actuator_init_module:2037 Enter
[ 8.012632] msm_actuator_platform_probe:1897 Enter
[ 8.016446] msm_actuator_platform_probe:1912 cell-index 0, rc 0
[ 8.022354] msm_actuator_platform_probe:1921 qcom,cci-master 0, rc 0
[ 8.028691] msm_camera_get_dt_vreg_data qcom,cam-vreg-name count 1
[ 8.034843] msm_camera_get_dt_vreg_data reg_name[0] = cam_vaf
[ 8.040586] msm_camera_get_dt_vreg_data:1180 no qcom,cam-vreg-type entries in dts
[ 8.048045] msm_camera_get_dt_vreg_data cam_vreg[0].min_voltage = 2850000
[ 8.054805] msm_camera_get_dt_vreg_data cam_vreg[0].max_voltage = 2850000
[ 8.061587] msm_camera_get_dt_vreg_data cam_vreg[0].op_mode = 100000
[ 8.067914] gpio count -2
[ 8.070545] msm_camera_pinctrl_init:1277 Getting pinctrl handle failed
[ 8.077028] msm_actuator_platform_probe:1949 ERR:msm_actuator_platform_probe: Error in reading actuator pinctrl
[ 8.087491] msm_actuator_platform_probe:1996 Exit
[ 8.091814] qcom,actuator: probe of 1b0c000.qcom,cci:qcom,actuator@0 failed with error -22
[ 8.100128] msm_actuator_platform_probe:1897 Enter
[ 8.104811] msm_actuator_platform_probe:1912 cell-index 1, rc 0
[ 8.110721] msm_actuator_platform_probe:1921 qcom,cci-master 1, rc 0
[ 8.117044] msm_camera_get_dt_vreg_data qcom,cam-vreg-name count 1
[ 8.123226] msm_camera_get_dt_vreg_data reg_name[0] = cam_vaf
[ 8.128955] msm_camera_get_dt_vreg_data:1180 no qcom,cam-vreg-type entries in dts
[ 8.136402] msm_camera_get_dt_vreg_data cam_vreg[0].min_voltage = 2850000
[ 8.143183] msm_camera_get_dt_vreg_data cam_vreg[0].max_voltage = 2850000
[ 8.149954] msm_camera_get_dt_vreg_data cam_vreg[0].op_mode = 100000
[ 8.156283] gpio count -2
[ 8.158923] msm_camera_pinctrl_init:1277 Getting pinctrl handle failed
[ 8.165395] msm_actuator_platform_probe:1949 ERR:msm_actuator_platform_probe: Error in reading actuator pinctrl
[ 8.175807] msm_actuator_platform_probe:1996 Exit
[ 8.180176] qcom,actuator: probe of 1b0c000.qcom,cci:qcom,actuator@1 failed with error -22
[ 8.191448] gpio count -2
[ 8.194392] LED trigger flashlight-trigger failed to register (-17)
[ 8.199639] gpio count -2
[ 8.206858] msm_sensor_get_sub_module_index qcom,actuator cell index 0, rc 0
[ 8.212891] msm_sensor_get_sub_module_index:227 src_node NULL
[ 8.218602] msm_sensor_get_sub_module_index:243 eeprom src_node NULL
[ 8.225009] msm_sensor_get_sub_module_index qcom,led flash cell index 0, rc 0
[ 8.232059] msm_sensor_get_sub_module_index:287 src_node NULL
[ 8.237773] msm_sensor_get_sub_module_index:303 src_node NULL
[ 8.243527] msm_sensor_get_sub_module_index csiphy_core[0] = 1
[ 8.249349] msm_sensor_get_sub_module_index csid_core[0] = 1
[ 8.254964] msm_camera_get_dt_vreg_data qcom,cam-vreg-name count 2
[ 8.261144] msm_camera_get_dt_vreg_data reg_name[0] = cam_vio
[ 8.266852] msm_camera_get_dt_vreg_data reg_name[1] = cam_vaf
[ 8.272605] msm_camera_get_dt_vreg_data:1180 no qcom,cam-vreg-type entries in dts
[ 8.280059] msm_camera_get_dt_vreg_data cam_vreg[0].min_voltage = 0
[ 8.286297] msm_camera_get_dt_vreg_data cam_vreg[1].min_voltage = 2850000
[ 8.293079] msm_camera_get_dt_vreg_data cam_vreg[0].max_voltage = 0
[ 8.299331] msm_camera_get_dt_vreg_data cam_vreg[1].max_voltage = 2850000
[ 8.306090] msm_camera_get_dt_vreg_data cam_vreg[0].op_mode = 0
[ 8.312002] msm_camera_get_dt_vreg_data cam_vreg[1].op_mode = 100000
[ 8.318349] gpio count 3
[ 8.320865] gpio_array[0] = 26
[ 8.323714] gpio_array[1] = 127gpio_array[2] = 33
[ 8.328427] msm_camera_get_dt_gpio_req_tbl cam_gpio_req_tbl[0].gpio = 26
[ 8.335256] msm_camera_get_dt_gpio_req_tbl cam_gpio_req_tbl[1].gpio = 127
[ 8.342056] msm_camera_get_dt_gpio_req_tbl cam_gpio_req_tbl[2].gpio = 33
[ 8.348724] msm_camera_get_dt_gpio_req_tbl cam_gpio_req_tbl[0].flags = 1
[ 8.355393] msm_camera_get_dt_gpio_req_tbl cam_gpio_req_tbl[1].flags = 0
[ 8.362089] msm_camera_get_dt_gpio_req_tbl cam_gpio_req_tbl[2].flags = 0
[ 8.368774] msm_camera_get_dt_gpio_req_tbl cam_gpio_req_tbl[0].label = CAMIF_MCLK0
[ 8.376314] msm_camera_get_dt_gpio_req_tbl cam_gpio_req_tbl[1].label = CAM_RESET0
[ 8.383792] msm_camera_get_dt_gpio_req_tbl cam_gpio_req_tbl[2].label = CAM_VDIG0
[ 8.391189] msm_camera_init_gpio_pin_tbl qcom,gpio-vdig 33
[ 8.396628] msm_camera_init_gpio_pin_tbl qcom,gpio-reset 127
[ 8.403270] msm_sensor_get_sub_module_index qcom,actuator cell index 1, rc 0
[ 8.409316] msm_sensor_get_sub_module_index:227 src_node NULL
[ 8.415031] msm_sensor_get_sub_module_index:243 eeprom src_node NULL
[ 8.421380] msm_sensor_get_sub_module_index:271 src_node NULL
[ 8.427097] msm_sensor_get_sub_module_index:287 src_node NULL
[ 8.432837] msm_sensor_get_sub_module_index:303 src_node NULL
[ 8.438578] msm_sensor_get_sub_module_index csiphy_core[0] = 2
[ 8.444381] msm_sensor_get_sub_module_index csid_core[0] = 2
[ 8.450028] msm_camera_get_dt_vreg_data qcom,cam-vreg-name count 2
[ 8.456183] msm_camera_get_dt_vreg_data reg_name[0] = cam_vio
[ 8.461916] msm_camera_get_dt_vreg_data reg_name[1] = cam_vaf
[ 8.467645] msm_camera_get_dt_vreg_data:1180 no qcom,cam-vreg-type entries in dts
[ 8.475112] msm_camera_get_dt_vreg_data cam_vreg[0].min_voltage = 0
[ 8.481359] msm_camera_get_dt_vreg_data cam_vreg[1].min_voltage = 2850000
[ 8.488132] msm_camera_get_dt_vreg_data cam_vreg[0].max_voltage = 0
[ 8.494370] msm_camera_get_dt_vreg_data cam_vreg[1].max_voltage = 2850000
[ 8.501152] msm_camera_get_dt_vreg_data cam_vreg[0].op_mode = 0
[ 8.507043] msm_camera_get_dt_vreg_data cam_vreg[1].op_mode = 100000
[ 8.513404] gpio count 3
[ 8.515915] gpio_array[0] = 27
[ 8.518780] gpio_array[1] = 126gpio_array[2] = 122
[ 8.523553] msm_camera_get_dt_gpio_req_tbl cam_gpio_req_tbl[0].gpio = 27
[ 8.530407] msm_camera_get_dt_gpio_req_tbl cam_gpio_req_tbl[1].gpio = 126
[ 8.537165] msm_camera_get_dt_gpio_req_tbl cam_gpio_req_tbl[2].gpio = 122
[ 8.543949] msm_camera_get_dt_gpio_req_tbl cam_gpio_req_tbl[0].flags = 1
[ 8.550630] msm_camera_get_dt_gpio_req_tbl cam_gpio_req_tbl[1].flags = 0
[ 8.557304] msm_camera_get_dt_gpio_req_tbl cam_gpio_req_tbl[2].flags = 0
[ 8.564000] msm_camera_get_dt_gpio_req_tbl cam_gpio_req_tbl[0].label = CAMIF_MCLK1
[ 8.571552] msm_camera_get_dt_gpio_req_tbl cam_gpio_req_tbl[1].label = CAM_RESET1
[ 8.579018] msm_camera_get_dt_gpio_req_tbl cam_gpio_req_tbl[2].label = CAM_VDIG1
[ 8.586400] msm_camera_init_gpio_pin_tbl qcom,gpio-vdig 122
[ 8.591951] msm_camera_init_gpio_pin_tbl qcom,gpio-reset 126
[ 8.598218] msm_sensor_get_sub_module_index:211 src_node NULL
[ 8.603312] msm_sensor_get_sub_module_index:227 src_node NULL
[ 8.609054] msm_sensor_get_sub_module_index:243 eeprom src_node NULL
[ 8.615417] msm_sensor_get_sub_module_index qcom,led flash cell index 2, rc 0
[ 8.622509] msm_sensor_get_sub_module_index:287 src_node NULL
[ 8.628236] msm_sensor_get_sub_module_index:303 src_node NULL
[ 8.633961] msm_sensor_get_sub_module_index csiphy_core[0] = 2
[ 8.639789] msm_sensor_get_sub_module_index csid_core[0] = 2
[ 8.645414] msm_camera_get_dt_vreg_data qcom,cam-vreg-name count 1
[ 8.651592] msm_camera_get_dt_vreg_data reg_name[0] = cam_vio
[ 8.657312] msm_camera_get_dt_vreg_data:1180 no qcom,cam-vreg-type entries in dts
[ 8.664782] msm_camera_get_dt_vreg_data cam_vreg[0].min_voltage = 0
[ 8.671029] msm_camera_get_dt_vreg_data cam_vreg[0].max_voltage = 0
[ 8.677270] msm_camera_get_dt_vreg_data cam_vreg[0].op_mode = 0
[ 8.683218] gpio count 3
[ 8.685702] gpio_array[0] = 28
[ 8.688572] gpio_array[1] = 40gpio_array[2] = 1019
[ 8.693339] msm_camera_get_dt_gpio_req_tbl cam_gpio_req_tbl[0].gpio = 28
[ 8.700198] msm_camera_get_dt_gpio_req_tbl cam_gpio_req_tbl[1].gpio = 40
[ 8.706869] msm_camera_get_dt_gpio_req_tbl cam_gpio_req_tbl[2].gpio = 1019
[ 8.713740] msm_camera_get_dt_gpio_req_tbl cam_gpio_req_tbl[0].flags = 1
[ 8.720424] msm_camera_get_dt_gpio_req_tbl cam_gpio_req_tbl[1].flags = 0
[ 8.727095] msm_camera_get_dt_gpio_req_tbl cam_gpio_req_tbl[2].flags = 0
[ 8.733792] msm_camera_get_dt_gpio_req_tbl cam_gpio_req_tbl[0].label = CAMIF_MCLK2
[ 8.741344] msm_camera_get_dt_gpio_req_tbl cam_gpio_req_tbl[1].label = CAM_RESET2
[ 8.748809] msm_camera_get_dt_gpio_req_tbl cam_gpio_req_tbl[2].label = CAM_VDIG
[ 8.756101] msm_camera_init_gpio_pin_tbl qcom,gpio-vdig 1019
[ 8.761743] msm_camera_init_gpio_pin_tbl qcom,gpio-reset 40
[ 8.772393] ————[ cut here ]————
[ 8.775973] WARNING: CPU: 5 PID: 1 at /media/1T_Code/Code/MOTO_SDM450/kernel/msm-3.18/drivers/clk/msm/clock-local2.c:233 rcg_clk_enable+0x50/0xb4()
[ 8.789159] Attempting to prepare camss_top_ahb_clk_src before setting its rate. Set the rate first!
[ 8.798272] Modules linked in:
[ 8.801314] CPU: 5 PID: 1 Comm: swapper/0 Tainted: G W 3.18.31-g27d91ba-dirty #8
[ 8.809730] Hardware name: Qualcomm Technologies, Inc. SDM450 MTP (DT)
[ 8.816242] Call trace:
[ 8.818677] [] dump_backtrace+0x0/0x270
[ 8.824054] [] show_stack+0x14/0x1c
[ 8.829092] [] dump_stack+0x80/0xa4
[ 8.834126] [] warn_slowpath_common+0x8c/0xb0
[ 8.840028] [] warn_slowpath_fmt+0x60/0x80
[ 8.845670] [] rcg_clk_enable+0x50/0xb4
[ 8.851052] [] clk_enable+0x13c/0x1b4
[ 8.856260] [] clk_enable+0x9c/0x1b4
[ 8.861384] [] msm_camera_clk_enable+0x16c/0x298
[ 8.867545] [] cpp_init_hardware+0xe4/0x614
[ 8.873273] [] cpp_probe+0x3a0/0x6e0
[ 8.878398] [] platform_drv_probe+0x38/0x84
[ 8.884125] [] driver_probe_device+0x164/0x370
[ 8.890114] [] __driver_attach+0x64/0x90
[ 8.895582] [] bus_for_each_dev+0x80/0xb0
[ 8.901138] [] driver_attach+0x20/0x28
[ 8.906433] [] bus_add_driver+0x128/0x200
[ 8.911989] [] driver_register+0x94/0xe0
[ 8.917459] [] __platform_driver_register+0x60/0x68
[ 8.923884] [] msm_cpp_init_module+0x18/0x20
[ 8.929698] [] do_one_initcall+0x1a0/0x1bc
[ 8.935341] [] kernel_init_freeable+0x14c/0x1e8
[ 8.941417] [] kernel_init+0x14/0xd8
[ 8.946535] —[ end trace dde6d505d3d31be9 ]—
[ 8.951224] MSM-CPP cpp_init_hardware:869 CPP HW Version: 0x40030003
[ 8.957485] MSM-CPP cpp_init_hardware:887 stream_cnt:0
[ 8.981242] __msm_jpeg_init:1537] Jpeg Device id 0
[ 8.996738] FG: fg_probe: FG Probe success - FG Revision DIG:3.1 ANA:1.2 PMIC subtype=17
[ 9.008381] TYPEC: qpnp_typec_probe: TypeC successfully probed state=0 CC-line-state=2
[ 9.016814] unable to find DT imem DLOAD mode node
[ 9.021396] unable to find DT imem EDLOAD mode node
[ 9.028773] thermal thermal_zone1: failed to read out thermal zone 1
[ 9.034839] thermal thermal_zone2: failed to read out thermal zone 2
[ 9.041318] thermal thermal_zone3: failed to read out thermal zone 3
[ 9.048467] qpnp_vadc_read: no vadc_chg_vote found
[ 9.052211] qpnp_vadc_get_temp: VADC read error with -22
[ 9.057507] thermal thermal_zone4: failed to read out thermal zone 4
[ 9.101154] device-mapper: uevent: version 1.0.3
[ 9.106204] device-mapper: ioctl: 4.28.0-ioctl (2014-09-17) initialised: [email protected]
[ 9.113871] device-mapper: req-crypt: dm-req-crypt successfully initalized.
[ 9.113871]
[ 9.123913] sdhci: Secure Digital Host Controller Interface driver
[ 9.129066] sdhci: Copyright(c) Pierre Ossman
[ 9.133401] sdhci-pltfm: SDHCI platform and OF driver helper
[ 9.140792] qcom_ice_get_pdevice: found ice device ffffffc0d2283480
[ 9.146013] qcom_ice_get_pdevice: matching platform device ffffffc0d49a9600
[ 9.159813] qcom_ice 7803000.sdcc1ice: QC ICE 2.1.44 device found @0xffffff8001b70000
[ 9.167253] sdhci_msm 7824900.sdhci: No vmmc regulator found
[ 9.172276] sdhci_msm 7824900.sdhci: No vqmmc regulator found
[ 9.178851] mmc0: SDHCI controller on 7824900.sdhci [7824900.sdhci] using 64-bit ADMA in CMDQ mode
[ 9.218192] sdhci_msm 7864900.sdhci: sdhci_msm_probe: ICE device is not enabled
[ 9.242685] sdhci_msm 7864900.sdhci: No vmmc regulator found
[ 9.247319] sdhci_msm 7864900.sdhci: No vqmmc regulator found
[ 9.253967] mmc1: SDHCI controller on 7864900.sdhci [7864900.sdhci] using 64-bit ADMA in legacy mode
[ 9.273281] mmc0: Out-of-interrupt timeout is 100[ms]
[ 9.277285] mmc0: BKOPS_EN equals 0x2
[ 9.280949] mmc0: eMMC FW version: 0x05
[ 9.284750] mmc0: CMDQ supported: depth: 16
[ 9.288960] mmc0: cache barrier support 0 flush policy 0
[ 9.298077] tz_log 8600720.tz-log: Hyp log service is not supported
[ 9.310818] hidraw: raw HID events driver (C) Jiri Kosina
[ 9.310888] cmdq_host_alloc_tdl: desc_size: 768 data_sz: 253952 slot-sz: 24
[ 9.311981] desc-base: 0xffffff8001e10000 trans-base: 0xffffff8002480000
[ 9.311981] desc_dma 0xf2c7a000 trans_dma: 0xf3180000
[ 9.312010] mmc0: CMDQ enabled on card
[ 9.312022] mmc0: new HS400 MMC card at address 0001
[ 9.315232] sdhci_msm_pm_qos_cpu_init (): voted for group #0 (mask=0xf) latency=2 (0xffffffc0d1716c00)
[ 9.315237] sdhci_msm_pm_qos_cpu_init (): voted for group #1 (mask=0xf0) latency=2 (0xffffffc0d1716c08)
[ 9.315472] mmcblk0: mmc0:0001 RH64AB 58.2 GiB
[ 9.315829] mmcblk0rpmb: mmc0:0001 RH64AB partition 3 4.00 MiB
[ 9.319167] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18 p19 p20 p21 p22 p23 p24 p25 p26 p27 p28 p29 p30 p31 p32 p33 p34 p35 p36 p37 p38 p39 p40 p41 p42 p43 p44 p45 p46 p47 p48 p49
[ 9.391796] usbcore: registered new interface driver usbhid
[ 9.396322] usbhid: USB HID core driver
[ 9.402255] ashmem: initialized
[ 9.405526] qpnp_coincell_charger_show_state: enabled=Y, voltage=3200 mV, resistance=2100 ohm
[ 9.422632] bimc-bwmon 408000.qcom,cpu-bwmon: BW HWmon governor registered.
[ 9.435283] devfreq soc:qcom,cpubw: Couldn’t update frequency transition information.
[ 9.442835] devfreq soc:qcom,mincpubw: Couldn’t update frequency transition information.
[ 9.456620] coresight-fuse a601c.fuse: Fuse initialized
[ 9.483639] coresight-csr 6001000.csr: CSR initialized
[ 9.489543] coresight-tmc 6028000.tmc: Byte Counter feature enabled
[ 9.495776] sps:BAM 0x0000000006044000 is registered.
[ 9.500482] coresight-tmc 6028000.tmc: TMC initialized
[ 9.505993] coresight-tmc 6027000.tmc: TMC initialized
[ 9.514713] nidnt boot config: 0
[ 9.519495] coresight-tpiu 6020000.tpiu: NIDnT on SDCARD only mode
[ 9.525011] coresight-tpiu 6020000.tpiu: TPIU initialized
[ 9.536125] coresight-replicator 6026000.replicator: REPLICATOR initialized
[ 9.547589] coresight-dbgui 6108000.dbgui: DebugUI capture enabled
[ 9.553322] coresight-dbgui 6108000.dbgui: DebugUI initializaed
[ 9.560525] coresight-stm 6002000.stm: STM initialized
[ 9.566097] coresight-hwevent 6101000.hwevent: Hardware Event driver initialized
[ 9.574891] coresight-etmv4 619c000.etm: ETMv4 initialized
[ 9.580784] coresight-etmv4 619d000.etm: ETMv4 initialized
[ 9.586641] coresight-etmv4 619e000.etm: ETMv4 initialized
[ 9.592503] coresight-etmv4 619f000.etm: ETMv4 initialized
[ 9.598457] coresight-etmv4 61bc000.etm: ETMv4 initialized
[ 9.604296] coresight-etmv4 61bd000.etm: ETMv4 initialized
[ 9.610188] coresight-etmv4 61be000.etm: ETMv4 initialized
[ 9.616056] coresight-etmv4 61bf000.etm: ETMv4 initialized
[ 9.622659] coresight-remote-etm soc:wcn_etm0: Remote ETM initialized
[ 9.628704] coresight-remote-etm soc:rpm_etm0: Remote ETM initialized
[ 9.635107] coresight-remote-etm soc:audio_etm0: Remote ETM initialized
[ 9.641608] coresight-remote-etm soc:modem_etm0: Remote ETM initialized
[ 9.648387] coresight-remote-etm soc:modem_etm1: Remote ETM initialized
[ 9.655460] coresight-qpdi: probe of 1941000.qpdi failed with error -1
[ 9.663906] usbcore: registered new interface driver snd-usb-audio
[ 9.674245] msm8953-pinctrl 1000000.pinctrl: could not parse property pins
[ 9.680582] 2-0040 supply VA not found, using dummy regulator
[ 9.685969] 2-0040 supply VP not found, using dummy regulator
[ 9.692528] cs35l35 2-0040: Cirrus Logic CS35L35 (35a35), Revision: 00
[ 9.698522] cs35l35_i2c_probe:[zjm] snd_soc_register_codec
[ 9.703496] cs35l35_i2c_probe:[zjm] snd_soc_register_codec success [ 9.745792] msm-pcm-lpa soc:qcom,msm-pcm-lpa: msm_pcm_probe: dev name soc:qcom,msm-pcm-lpa
[ 9.762288] CRUS_SP_INIT: initializing misc device
[ 9.774346] u32 classifier
[ 9.776010] Actions configured
[ 9.779539] Netfilter messages via NETLINK v0.30.
[ 9.784227] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 9.791997] ctnetlink v0.93: registering with nfnetlink.
[ 9.800715] xt_time: kernel timezone is -0000
[ 9.804564] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 9.810212] arp_tables: (C) 2002 David S. Miller
[ 9.814120] TCP: cubic registered
[ 9.817232] Initializing XFRM netlink socket
[ 9.825532] NET: Registered protocol family 10
[ 9.833343] mip6: Mobile IPv6
[ 9.835336] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 9.841870] sit: IPv6 over IPv4 tunneling driver
[ 9.847141] NET: Registered protocol family 17
[ 9.850654] NET: Registered protocol family 15
[ 9.855602] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 9.867584] Ebtables v2.0 registered
[ 9.871524] Bluetooth: ffffffc07eebbcd8
[ 9.874782] Bluetooth: ffffffc07eebbcc8Bluetooth: ffffffc07eebbd08
[ 9.880956] Bluetooth: ffffffc07eebbce8Bluetooth: ffffffc07eebbce8
[ 9.887103] Bluetooth: ffffffc07eebbcb8Bluetooth: ffffffc07eebbd38
[ 9.893264] Bluetooth: ffffffc07eebbd08[ 9.897158] _core: L2TP core driver, V2.0
[ 9.901460] _ppp: PPPoL2TP kernel driver, V2.0
[ 9.906190] _ip: L2TP IP encapsulation support (L2TPv3)
[ 9.912357] _netlink: L2TP netlink interface
[ 9.916400] _eth: L2TP ethernet pseudowire support (L2TPv3)
[ 9.922319] _debugfs: L2TP debugfs support
[ 9.926675] _ip6: L2TP IP encapsulation support for IPv6 (L2TPv3)
[ 9.935550] NET: Registered protocol family 27
[ 9.952282] subsys-pil-tz a21b000.qcom,pronto: for wcnss segments only will be dumped.
[ 9.964917] pil-q6v5-mss 4080000.qcom,mss: for modem segments only will be dumped.
[ 9.980328] sps:BAM 0x0000000007104000 is registered.
[ 9.988604] qpnp-smbcharger qpnp-smbcharger-18: node /soc/qcom,spmi@200f000/qcom,pmi8950@2/qcom,qpnp-smbcharger IO resource absent!
[ 10.000024] smbcharger_charger_otg: no parameters
[ 10.058273] msm-dwc3 7000000.ssusb: Avail curr from USB = 1500
[ 10.073091] qpnp-smbcharger qpnp-smbcharger-18: node /soc/qcom,spmi@200f000/qcom,pmi8950@2/qcom,qpnp-smbcharger IO resource absent!
[ 11.196153] qpnp-smbcharger qpnp-smbcharger-18: SMBCHG successfully probe Charger version=SCHG_LITE Revision DIG:0.0 ANA:0.1 batt=1 dc=1 usb=1
[ 11.211931] EDAC DEVICE0: Giving out device to module soc:arm64-cpu-erp controller cache: DEV soc:arm64-cpu-erp (INTERRUPT)
[ 11.223162] ARM64 CPU ERP: Could not find IRQ property. Proceeding anyway.
[ 11.229875] ARM64 CPU ERP: SBE detection is disabled.
[ 11.236586] Registered cp15_barrier emulation handler
[ 11.240677] Registered setend emulation handler
[ 11.246563] Loading compiled-in X.509 certificates
[ 11.252325] Loaded X.509 cert ‘Magrathea: Glacier signing key: 7ebbe8449f2584e2f461752313b1228f0b51feef’
[ 11.369573] fastrpc soc:qcom,adsprpc-mem: for adsp_rh segments only will be dumped.
[ 11.380989] RNDIS_IPA module is loaded.
[ 11.385434] file system registered
[ 11.388280] mbim_init: initialize 1 instances
[ 11.392536] mbim_init: Initialized 1 ports
[ 11.403250] rndis_qc_init: initialize rndis QC instance
[ 11.408726] Number of LUNs=8
[ 11.410595] Mass Storage Function, version: 2009/09/11
[ 11.415693] LUN: removable file: (no medium)
[ 11.420031] Number of LUNs=1
[ 11.423012] LUN: removable file: (no medium)
[ 11.427056] Number of LUNs=1
[ 11.431371] android_usb gadget: android_usb ready
[ 11.435749] FUSB fusb30x_init - Start driver initialization…
[ 11.441113] fusb302 2-0022: fusb30x_probe
[ 11.445325] fusb302 2-0022: fusb30x_power_init():vdd count = 2
[ 11.450779] fusb302 2-0022: fusb30x_power_init():vdd power on.
[ 11.457618] FUSB fusb_InitializeGPIO - INT_N GPIO initialized as pin ‘46’
[ 11.463482] FUSB fusb_InitializeGPIO VBus5V init as pin ‘109’ and is set to ‘0’
[ 11.477801] fusb302 2-0022: FUSB fusb30x_probe FUSB30X Driver loaded successfully!
[ 11.487378] input: gpio-keys as /devices/soc/soc:gpio_keys/input/input7
[ 11.493846] qcom,qpnp-rtc qpnp-rtc-8: setting system clock to 1970-01-01 00:00:21 UTC (21)
[ 11.508162] msm-core initialized without polling period
[ 11.520035] parse_cpu_levels: idx 1 276
[ 11.522852] calculate_residency: residency < 0 for LPM
[ 11.528216] parse_cpu_levels: idx 1 286
[ 11.531789] calculate_residency: residency < 0 for LPM
[ 11.548616] qcom,qpnp-flash-led qpnp-flash-led-24: Unable to acquire pinctrl
[ 11.558760] led_gpio_flash_probe seq_name[0] = flash_en
[ 11.562943] led_gpio_flash_probe:180 seq_type[0] 0
[ 11.567717] led_gpio_flash_probe seq_name[1] = flash_en
[ 11.572967] qcom,leds-gpio-flash soc:qcom,leds-gpio-flash: led_gpio_flash_probe failed 174
[ 11.581196] led_gpio_flash_probe:180 seq_type[1] 0
[ 11.586378] led_gpio_flash_probe:leds-msm-gpio-flash successfully!
[ 11.594917] rmnet_ipa started initialization
[ 11.598166] IPA SSR support = True
[ 11.601528] IPA ipa-loaduC = True
[ 11.604827] IPA SG support = True
[ 11.614231] ipa ipa_sps_irq_control_all:938 EP (5) not allocated.
[ 11.619327] ipa ipa2_uc_state_check:301 uC is not loaded
[ 11.625769] rmnet_ipa completed initialization
[ 11.641326] qcom,cc-debug-8953 1874000.qcom,cc-debug: Registered Debug Mux successfully
[ 11.676877] msm8952-asoc-wcd c051000.sound: default codec configured
[ 11.682257] is_us_eu_switch_gpio_support: gpio set name does not exist: us_eu_gpio
[ 11.689591] msm8952_asoc_machine_probe: failed to is_us_eu_switch_gpio_support -22
[ 11.701829] msm8952-asoc-wcd c051000.sound: ASoC: platform (null) not registered
[ 11.708258] msm8952-asoc-wcd c051000.sound: snd_soc_register_card failed (-517)
[ 11.720382] vdd_vreg: disabling
[ 11.722484] adv_vreg: disabling
[ 11.725647] gfx_mem_acc_corner: disabling
[ 11.729630] apc_mem_acc_corner: disabling
[ 11.733612] clock_late_init: Removing enables held for handed-off clocks
[ 11.745248] ALSA device list:
[ 11.747170] No soundcards f 11.751902] Freeing unused kernel memory: 1180K (ffffffc001665000 - ffffffc00178c000)
[ 11.758773] Freeing alternatives memory: 84K (ffffffc00178c000 - ffffffc0017a1000)
[ 11.769352] init: init first stage started!
[ 11.838339] random: nonblocking pool is initialized
[ 11.903941] SELinux: Class can_socket not defined in policy.
[ 11.908673] SELinux: the above unknown classes and permissions will be denied
[ 12.049409] audit: type=1403 audit(22.049:2): policy loaded auid=4294967295 ses=4294967295
[ 12.057748] audit: type=1404 audit(22.049:3): enforcing=1 old_enforcing=0 auid=4294967295 ses=4294967295
[ 12.098407] init: (Initializing SELinux enforcing took 0.33s.)
[ 12.109255] init: init second stage started!
[ 12.131623] init: Running restorecon…
[ 12.518141] of_batterydata_get_best_profile: qrd_msm8937_sku1_2800mah found
[ 12.527895] FG: fg_batt_profile_init: Battery profile not same, clearing data
[ 12.672383] init: waitpid failed: No child processes
[ 12.676700] init: (Loading properties from /default.prop took 0.00s.)
[ 12.685689] init: (Parsing /init.environ.rc took 0.00s.)
[ 12.690436] init: (Parsing /init.usb.rc took 0.00s.)
[ 12.696466] init: /init.qcom.rc: 607: user requires 1 argument
[ 12.707845] init: (Parsing init.qcom.usb.rc took 0.01s.)
[ 12.714466] init: (Parsing init.msm.usb.configfs.rc took 0.00s.)
[ 12.719889] init: ignored duplicate definition of service ‘perfd’init: init.target.rc: 235: invalid keyword ‘load_all_props’
[ 12.730906] init: could not import file ‘init.carrier.rc’ from ‘init.target.rc’: No such file or directory
[ 12.740305] init: (Parsing init.target.rc took 0.02s.)
[ 12.745624] init: (Parsing init.qcom.factory.rc took 0.00s.)
[ 12.751221] init: (Parsing init.qcom.test.rc took 0.00s.)
[ 12.756427] init: (Parsing /init.qcom.rc took 0.06s.)
[ 12.762616] init: (Parsing /init.usb.configfs.rc took 0.00s.)
[ 12.767471] init: (Parsing /init.zygote64_32.rc took 0.00s.)
[ 12.772998] init: (Parsing /init.rc took 0.09s.)
[ 12.778638] init: Starting service ‘ueventd’…
[ 12.785284] init: Waiting for /dev/.coldboot_done…
[ 12.787483] ueventd: ueventd started!
[ 13.629470] FG: fg_batt_profile_init: Battery SOC: 35, V: 3802162uV
[ 13.635187] of_batterydata_get_best_profile: qrd_msm8937_sku1_2800mah found
[ 13.968139] ueventd: Coldboot took 1.18s.
[ 13.975483] init: Waiting for /dev/.coldboot_done took 1.19s.
[ 13.993172] init: write_file: Unable to open ‘/proc/sys/kernel/hung_task_timeout_secs’: No such file or directory
[ 14.002493] init: write_file: Unable to open ‘/proc/cpu/alignment’: No such file or directory
[ 14.021806] Registered swp emulation handler
[ 14.026100] init: write_file: Unable to open ‘/sys/fs/cgroup/memory/bg/memory.swappiness’: No such file or directory
[ 14.035669] init: write_file: Unable to open ‘/sys/fs/cgroup/memory/bg/memory.move_charge_at_immigrate’: No such file or directory
[ 14.629057] init (436) used greatest stack depth: 12632 bytes left
[ 14.690144] fs_mgr: Enabling dm-verity for system (mode 2)
[ 14.694624] fs_mgr: loading verity table: ‘1 /dev/block/bootdevice/by-name/system /dev/block/bootdevice/by-name/system 4096 4096 774155 774155 sha256 b43a8d2ada24913584b6e84997e71c4253e993413c344450882913e8869dc3ed aee087a5be3b982978c923f566a94613496b417f2af592639bc80d141e34dfe7 10 restart_on_corruption use_fec_from_device /dev/block/bootdevice/by-name/system fec_start 780261 fec_blocks 780261 fec_roots 2 ignore_zero_blocks’
[ 14.791058] EXT4-fs (dm-0): mounting with “discard” option, but the device does not support discard
[ 14.799314] EXT4-fs (dm-0): mounted filesystem with ordered data mode. Opts: barrier=1,discard
[ 14.808007] fs_mgr: __mount(source=/dev/block/dm-0,target=/system,type=ext4)=0
[ 14.816260] EXT4-fs (mmcblk0p49): VFS: Can’t find ext4 filesystem
[ 14.821450] fs_mgr: __mount(source=/dev/block/bootdevice/by-name/userdata,target=/data,type=ext4)=-1
[ 14.831571] fs_mgr: fs_mgr_mount_all(): possibly an encryptable blkdev /dev/block/bootdevice/by-name/userdata for mount /data type ext4 )
[ 14.845543] init (432) used greatest stack depth: 10504 bytes left
[ 14.875719] init: (Parsing /system/etc/init/atrace.rc took 0.00s.)
[ 14.881927] init: (Parsing /system/etc/init/audioserver.rc took 0.00s.)
[ 14.888405] init: (Parsing /system/etc/init/bootanim.rc took 0.00s.)
[ 14.894875] init: (Parsing /system/etc/init/bootstat.rc took 0.00s.)
[ 14.901164] init: (Parsing /system/etc/init/cameraserver.rc took 0.00s.)
[ 14.907735] init: (Parsing /system/etc/init/debuggerd.rc took 0.00s.)
[ 14.914243] init: (Parsing /system/etc/init/debuggerd64.rc took 0.00s.)
[ 14.920838] init: (Parsing /system/etc/init/drmserver.rc took 0.00s.)
[ 14.927268] init: (Parsing /system/etc/init/dumpstate.rc took 0.00s.)
[ 14.933680] init: (Parsing /system/etc/init/gatekeeperd.rc took 0.00s.)
[ 14.940326] init: (Parsing /system/etc/init/init-debug.rc took 0.00s.)
[ 14.946699] init: (Parsing /system/etc/init/installd.rc took 0.00s.)
[ 14.953124] init: (Parsing /system/etc/init/keystore.rc took 0.00s.)
[ 14.959448] init: (Parsing /system/etc/init/lmkd.rc took 0.00s.)
[ 14.965649] init: (Parsing /system/etc/init/logcatd.rc took 0.00s.)
[ 14.971958] init: (Parsing /system/etc/init/logd.rc took 0.00s.)
[ 14.977781] init: (Parsing /system/etc/init/mdnsd.rc took 0.00s.)
[ 14.983905] init: (Parsing /system/etc/init/mediacodec.rc took 0.00s.)
[ 14.990480] init: (Parsing /system/etc/init/mediadrmserver.rc took 0.00s.)
[ 14.997231] init: (Parsing /system/etc/init/mediaextractor.rc took 0.00s.)
[ 15.004205] init: (Parsing /system/etc/init/mediaserver.rc took 0.00s.)
[ 15.010812] init: (Parsing /system/etc/init/mtpd.rc took 0.00s.)
[ 15.016671] init: (Parsing /system/etc/init/netd.rc took 0.00s.)
[ 15.022729] init: (Parsing /system/etc/init/perfprofd.rc took 0.00s.)
[ 15.029189] init: (Parsing /system/etc/init/racoon.rc took 0.00s.)
[ 15.035291] init: (Parsing /system/etc/init/rild.rc took 0.00s.)
[ 15.041341] init: (Parsing /system/etc/init/servicemanager.rc took 0.00s.)
[ 15.048191] init: (Parsing /system/etc/init/surfaceflinger.rc took 0.00s.)
[ 15.054999] init: (Parsing /system/etc/init/uncrypt.rc took 0.00s.)
[ 15.061315] init: (Parsing /system/etc/init/vdc.rc took 0.00s.)
[ 15.067129] init: (Parsing /system/etc/init/vold.rc took 0.00s.)
[ 15.096191] EXT4-fs (mmcblk0p25): recovery complete
[ 15.100603] EXT4-fs (mmcblk0p25): mounted filesystem with ordered data mode. Opts: barrier=1
[ 15.140065] EXT4-fs (mmcblk0p26): recovery complete
[ 15.144522] EXT4-fs (mmcblk0p26): mounted filesystem with ordered data mode. Opts: barrier=1
[ 15.162489] EXT4-fs (mmcblk0p12): mounted filesystem with ordered data mode. Opts: barrier=1
[ 15.178809] EXT4-fs (mmcblk0p30): VFS: Can’t find ext4 filesystem
[ 15.187346] init: Starting service ‘logd’…
[ 15.281118] logd.auditd: start
[ 15.283209] logd.klogd: 15275198795
[ 16.193274] init: property_set(“ro.cutoff_voltage_mv”, “3400”) failed
[ 16.199156] init: (Loading properties from /system/build.prop took 0.01s.)
[ 16.205643] init: (Loading properties from /vendor/build.prop took 0.00s.)
[ 16.212477] init: (Loading properties from /factory/factory.prop took 0.00s.)
[ 16.219696] init: /recovery not specified in fstab
[ 16.225445] init: Starting service ‘debuggerd’…
[ 16.231047] init: Starting service ‘debuggerd64’…
[ 16.238266] init: Starting service ‘vold’…
[ 16.243768] init: Not bootcharting.
[ 16.474198] init: Starting service ‘exec 1 (/system/bin/tzdatacheck)’…
[ 16.500008] init: Service ‘exec 1 (/system/bin/tzdatacheck)’ (pid 477) exited with status 0
[ 16.532686] init: Starting service ‘perfd’…
[ 16.547200] init: write_file: Unable to open ‘/sys/block/dm-1/queue/read_ahead_kb’: No such file or directory
[ 16.561657] init: (Loading properties from /data/local.prop took 0.00s.)
[ 16.567923] init: Starting service ‘logd-reinit’…
[ 16.591292] logd.daemon: reinit
[ 16.608606] subsys-pil-tz c200000.qcom,lpass: adsp: loading from 0x000000008d600000 to 0x000000008e700000
[ 16.941335] subsys-pil-tz c200000.qcom,lpass: adsp: Brought out of reset
[ 16.977569] subsys-pil-tz c200000.qcom,lpass: adsp: Power/Clock ready interrupt received
[ 16.977580] subsys-pil-tz c200000.qcom,lpass: Subsystem error monitoring/handling services are up
[ 16.978133] init: Service ‘logd-reinit’ (pid 479) exited with status 0
[ 16.978367] sensors-ssc soc:qcom,msm-ssc-sensors: slpi_loader_do: pil get failed,
[ 16.978370] sensors-ssc soc:qcom,msm-ssc-sensors: slpi_loader_do: SLPI image loading failed
[ 16.978473] init: Starting service ‘exec 2 (/init.qcom.early_boot.sh)’…
[ 16.978618] diag: In diag_send_feature_mask_update, control channel is not open, p: 1, 0000000000000000
[ 17.010965] msm8952-asoc-wcd c051000.sound: default codec configured
[ 17.010992] is_us_eu_switch_gpio_support: gpio set name does not exist: us_eu_gpio
[ 17.010993] msm8952_asoc_machine_probe: failed to is_us_eu_switch_gpio_support -22
[ 17.015625] msm8952-asoc-wcd c051000.sound: ASoC: platform (null) not registered
[ 17.015659] msm8952-asoc-wcd c051000.sound: snd_soc_register_card failed (-517)
[ 17.049132] msm8952-asoc-wcd c051000.sound: default codec configured
[ 17.049160] is_us_eu_switch_gpio_support: gpio set name does not exist: us_eu_gpio
[ 17.049161] msm8952_asoc_machine_probe: failed to is_us_eu_switch_gpio_support -22
[ 17.049490] apr_tal:Q6 Is Up
[ 17.060314] wcd-spmi-core msm8x16_wcd_codec-11: Error: regulator not found:cdc-vdd-spkdrv
[ 17.082891] msm-pcm-routing soc:qcom,msm-pcm-routing: ASoC: no dapm match for MM_DL5 –> MultiMedia5 –> TERT_MI2S_RX Audio Mixer
[ 17.082895] msm-pcm-routing soc:qcom,msm-pcm-routing: ASoC: Failed to add route MM_DL5 -> MultiMedia5 -> TERT_MI2S_RX Audio Mixer
[ 17.083000] msm-pcm-routing soc:qcom,msm-pcm-routing: ASoC: no dapm match for MM_DL8 –> MultiMedia8 –> TERT_MI2S_RX Audio Mixer
[ 17.083004] msm-pcm-routing soc:qcom,msm-pcm-routing: ASoC: Failed to add route MM_DL8 -> MultiMedia8 -> TERT_MI2S_RX Audio Mixer
[ 17.084462] msm-pcm-routing soc:qcom,msm-pcm-routing: ASoC: no dapm match for INT_FM_TX –> INTERNAL_FM_TX –> SEC_MI2S_RX Port Mixer
[ 17.084466] msm-pcm-routing soc:qcom,msm-pcm-routing: ASoC: Failed to add route INT_FM_TX -> INTERNAL_FM_TX -> SEC_MI2S_RX Port Mixer
[ 17.107652] msm-pcm-routing soc:qcom,msm-pcm-routing: ASoC: no dapm match for VOICEMMODE1_DL –> VoiceMMode1 –> SEC_MI2S_RX_Voice Mixer
[ 17.107657] msm-pcm-routing soc:qcom,msm-pcm-routing: ASoC: Failed to add route VOICEMMODE1_DL -> VoiceMMode1 -> SEC_MI2S_RX_Voice Mixer
[ 17.107716] msm-pcm-routing soc:qcom,msm-pcm-routing: ASoC: no dapm match for VOICEMMODE2_DL –> VoiceMMode2 –> SEC_MI2S_RX_Voice Mixer
[ 17.107719] msm-pcm-routing soc:qcom,msm-pcm-routing: ASoC: Failed to add route VOICEMMODE2_DL -> VoiceMMode2 -> SEC_MI2S_RX_Voice Mixer
[ 17.109960] sysmon-qmi: sysmon_clnt_svc_arrive: Connection established between QMI handle and adsp’s SSCTL service
[ 17.117672] msm-pcm-routing soc:qcom,msm-pcm-routing: ASoC: no source widget found for AUDIO_REF_EC_UL3 MUX
[ 17.117677] msm-pcm-routing soc:qcom,msm-pcm-routing: ASoC: Failed to add route AUDIO_REF_EC_UL3 MUX -> direct -> MM_UL3
[ 17.133019] msm-pcm-routing soc:qcom,msm-pcm-routing: ASoC: no dapm match for SEC_MI2S_TX –> SEC_MI2S_TX –> SLIMBUS_0_RX Port Mixer
[ 17.133024] msm-pcm-routing soc:qcom,msm-pcm-routing: ASoC: Failed to add route SEC_MI2S_TX -> SEC_MI2S_TX -> SLIMBUS_0_RX Port Mixer
[ 17.135640] msm-pcm-routing soc:qcom,msm-pcm-routing: ASoC: no dapm match for VOICE2_STUB_DL –> Voice2 Stub –> INTERNAL_BT_SCO_RX_Voice Mixer
[ 17.135644] msm-pcm-routing soc:qcom,msm-pcm-routing: ASoC: Failed to add route VOICE2_STUB_DL -> Voice2 Stub -> INTERNAL_BT_SCO_RX_Voice Mixer
[ 17.140793] msm-pcm-routing soc:qcom,msm-pcm-routing: ASoC: no sink widget found for SENARY_MI2S_TX
[ 17.140799] msm-pcm-routing soc:qcom,msm-pcm-routing: ASoC: Failed to add route BE_IN -> direct -> SENARY_MI2S_TX
[ 17.319885] L-Notify: Generel: 7
[ 17.343205] msm-pcm-routing soc:qcom,msm-pcm-routing: ASoC: Failed to create SEC_MI2S_RX Port Mixer debugfs file
[ 17.436898] msm-pcm-routing soc:qcom,msm-pcm-routing: ASoC: mux SLIM_0_RX AANC MUX has no paths
[ 17.473348] wcd-spmi-core msm8x16_wcd_codec-11: ASoC: mux RX3 MIX1 INP3 has no paths
[ 17.481378] wcd-spmi-core msm8x16_wcd_codec-11: ASoC: mux RX2 MIX1 INP3 has no paths
[ 17.594740] CRUS msm_crus_pb_add_controls: platform->dev = ffffffc0d4a85810
[ 17.607714] cs35l35_codec_probe:[zjm] enter
[ 17.611341] cs35l35_codec_probe:[zjm] return ok
[ 17.619797] msm8952-asoc-wcd c051000.sound: control 3:0:0:IEC958 Playback PCM Stream:0 is already present
[ 17.628351] msm-hdmi-dba-codec-rx soc:qcom,msm-hdmi-dba-codec-rx: ASoC: Failed to add IEC958 Playback PCM Stream: -16
[ 17.638956] msm_dba_get_probed_device: Device not found (adv7533, 0)
[ 17.645249] msm_dba_register_client: Device not found (adv7533, 0)
[ 17.651447] msm_hdmi_dba_codec_rx_init_dba: error in registering audio client 0
[ 17.680834] init: Service ‘exec 2 (/init.qcom.early_boot.sh)’ (pid 495) exited with status 0
[ 17.694694] init: Starting service ‘healthd’…
[ 17.699940] init: Starting service ‘qcom-c_core-sh’…
[ 17.706192] init: Starting service ‘irsc_util’…
[ 17.707584] binder: 546:546 transaction failed 29189, size 0-0
[ 17.717776] init: Starting service ‘rmt_storage’…
[ 17.723074] init: cannot find ‘/system/bin/rfs_access’ (No such file or directory), disabling ‘rfs_access’
[ 17.732550] init: Starting service ‘tftp_server’…
[ 17.738823] init: Starting service ‘config_bt_addr’…
[ 17.744876] init: Starting service ‘config_bluetooth’…
[ 17.749628] cs35l35_codec_set_sysclk:[zjm] cs35l35->mclk=12288000
[ 17.751371] init: Starting service ‘sensor-sh’…
[ 17.753751] init: Starting service ‘esepmdaemon’…
[ 17.755832] init: Starting service ‘qcom-usb-sh’…
[ 17.758592] init: Starting service ‘qseecomd’…
[ 17.760977] init: Starting service ‘per_mgr’…
[ 17.762305] init: Starting service ‘cs-early-boot’…
[ 17.764427] init: Starting service ‘lmkd’…
[ 17.767023] init: Starting service ‘servicemanager’…
[ 17.769385] init: Starting service ‘surfaceflinger’…
[ 17.771358] init: Service ‘irsc_util’ (pid 548) exited with status 0
[ 17.784363] init: write_file: Unable to open ‘/proc/sys/net/ipv6/conf/rmnet0/accept_ra’: No such file or directory
[ 17.784452] init: write_file: Unable to open ‘/proc/sys/net/ipv6/conf/rmnet1/accept_ra’: No such file or directory
[ 17.784534] init: write_file: Unable to open ‘/proc/sys/net/ipv6/conf/rmnet2/accept_ra’: No such file or RӓJz}ɅzɁ”ѽ¢Jz}ɅzɁ”ѽ¢Jz}ɅzɁ”ѽ¢ªz}ɅzɁ”ѽ¢ʚz}ɅzɁ”ѽªJ[ 17.738823] init: Starting service ‘config_bt_addr’… ɅzɁ”ѽªJz}z
[ 17.732550] init: Starting service ‘tftp_server’… ɅzɁ”ѽªJz}z
[ 17.723074] init: cannot find ‘/system/bin/rfs_access’ (No such file or directory), disabling ‘rfs_access’ ɅzɁ”ѽªJz}z
[ 17.717776] init: Starting service ‘rmt_storage’… ɅzɁ”ѽªªz}z
[ 17.707584] binder: 546:546 transaction failed 29189, size 0-0 ɅzɁ”ѽºJѥ2bѡٽёݑյzɁ”ѽºJ”ѥ2 17.717776] init: Starting service ‘rmt_storage’… ɅzɁ”ѽªªz}z
“ёݑյٽ.723074] iRӓJѥ2bѡٽёݑյzɁ”ѽºJ”2m/bin/rfs_access’ (No such file or directory), disabling ‘rfs_access’ ɅzɁ”ѽªJz}z
“ёݑյٽ.723074] zɁ”ѽʂJzz͍zɁ”ѽʂJzɥJ”2m/bin/rfs_access’ (No such file or directory), disabling ‘rfs_access’ ɅzɁ”ѽªJz}z
Ɂ”ѽʂJzrzɁ”ѽʂJzѝɁ”ѽʚJzz͍rzɁ”ѽʚJzz͍ͥrzɁ”ѽʪJ:*͕ѡɉ”Jѕ͕ѕٕRӓ Jz2 ɅzɁ”ѽªJz}z
Ɂ”ѽz”zJz2rzɁ”ѽz”zJzѕ}rzɁ”ѽR”ѥrrj Rӓnfig_btѥbrrrj Rӓ  ɅzɁ”ѽªJz}z
[ 17.744876] init: Starting service ‘config_bluetooth’… ͉ɕ
Rѥ
rrrj Rӓ28] cѥrrrj Rӓdec_setѥrj Rӓ:ѥᕍzrrrj Rӓ5->m:ᕍzB*ѡ0 ɅzɁ”RӓJz}͑
²Jr
ѕٕRӓ 17.71371] init: Starting service ‘sensor-sh’…
[ 17.75Ց:bщɉ”Jѕ}ٕRӓ):B*ѡervice ‘eRӓ)Ս}́ron’… ,W ɅzɁ”ѽªJRӓ)ʺjjj”Uɕ͕jͅjRR’ Starting service ‘sensors’…
[ 18.016191] init: Service ‘sensor-sh’ (pid 556) exited with status 0
[ 18.277229] init: Service ‘qcom-usb-sh’ (pid 559) exited with status 0
[ 18.302050] cs35l35_dai_set_sysclk, karl start.
[ 18.302068] init: Service ‘config_bluetooth’ (pid 554) exited with status 0
[ 18.318701] init: Service ‘cs-early-boot’ (pid 562) exited with status 0
[ 18.324924] cs35l35_set_dai_fmt, karl startmanager’…
[ 18.328682] cs35l35_set_dai_fmt, karl endceflinger’…
[ 18.360197] devfreq soc:qcom,kgsl-busmon: Couldn’t update frequency transition information.
[ 18.713736] healthd: BatteryCycleCountPath not foundsys/net/ipv6/conf/rmnet0/accept_ra’: No such file or directory
[ 18.875877] init: Starting service ‘bootanim’…roc/sys/net/ipv6/conf/rmnet1/accept_ra’: No such file or directory
[ 18.881817] gpio-65 (?): _gpiod_direction_output_raw: tried to set a GPIO tied to an IRQ as outputile or RӓJz}ɅzɁ”ѽ¢Jz}ɅzɁ”ѽ¢Jz}ɅzɁ”ѽ¢ªz}ɅzɁ”ѽ¢ʚz}ɅzɁ”ѽªJ[ 18.890174] type=1400 audit(28.889:7): avc: denied { getattr } for pid=697 comm=”bootanimation” path=”/vendor” dev=”rootfs” ino=13904 scontext=u:r:bootanim:s0 tcontext=u:object_r:rootfs:s0 tclass=lnk_file permissive=0
[ 18.898963] gpio-65 (?): _gpiod_direction_output_raw: tried to set a GPIO tied to an IRQ as output
[ 19.319244] M-Notify: General: 7
[ 19.594587] diag: In diag_send_feature_mask_update, control channel is not open, p: 0, 0000000000000000
[ 19.598296] ipa-wan handle_indication_req:133 not send indication
[ 19.600602] ipa ipa_uc_wdi_event_log_info_handler:322 WDI feature missing 0x1
[ 19.600605] ipa ipa_uc_ntn_event_log_info_handler:39 NTN feature missing 0x1
[ 19.600628] ipa ipa_uc_response_hdlr:461 IPA uC loaded
[ 19.600692] ipa ipa_sps_irq_control_all:938 EP (5) not allocated.
[ 19.603984] ipa ipa_sps_irq_control_all:938 EP (5) not allocated.
[ 19.605668] ipa ipa_sps_irq_control_all:938 EP (5) not allocated.
[ 19.888315] QSEECOM: __qseecom_process_incomplete_cmd: fail:resp res= -65,app_id = 0,lstr = 12288
[ 19.888510] scm_call failed: func id 0x42000c16, ret: -1, syscall returns: 0x0, 0x0, 0x0
[ 19.888531] memshare: hyp_assign_phys failed size=2097152 err=-5
[ 19.942210] init: Service ‘config_bt_addr’ (pid 552) exited with status 0
[ 20.046105] QSEECOM: qseecom_create_key: Set the key successfully
[ 20.425590] init: (Loading properties from /data/local.prop took 0.00s.)
[ 20.512993] init: Starting service ‘logd-reinit’…
[ 20.531797] init: Not bootcharting.
[ 20.539255] init: Service ‘logd-reinit’ (pid 726) exited with status 0
[ 20.620926] init: Starting service ‘exec 4 (/system/bin/tzdatacheck)’…
[ 20.645441] init: Service ‘exec 4 (/system/bin/tzdatacheck)’ (pid 728) exited with status 0
[ 20.705204] init: Starting service ‘exec 5 (/system/bin/bootstat)’…
[ 20.718782] type=1400 audit(30.719:8): avc: denied { getattr } for pid=729 comm=”bootstat” path=”/vendor” dev=”rootfs” ino=13904 scontext=u:r:bootstat:s0 tcontext=u:object_r:rootfs:s0 tclass=lnk_file permissive=0
[ 20.740215] init: Service ‘exec 5 (/system/bin/bootstat)’ (pid 729) exited with status 0
[ 20.749713] init: cannot find ‘/system/bin/update_verifier’ (No such file or directory), disabling ‘exec 6 (/system/bin/update_verifier)’
[ 20.761192] init: cannot find ‘/system/bin/install-recovery.sh’ (No such file or directory), disabling ‘flash_recovery’
[ 20.772559] init: Starting service ‘qcomsysd’…
[ 20.778378] init: Starting service ‘qcom-c_main-sh’…
[ 20.784772] init: Starting service ‘cnd’…
[ 20.790463] init: Starting service ‘ptt_socket_app’…
[ 20.796836] init: Starting service ‘cnss_diag’…
[ 20.802183] init: cannot find ‘/system/bin/usb_uicc_client’ (No such file or directory), disabling ‘usb_uicc_daemon’
[ 20.812675] init: Starting service ‘time_daemon’…
[ 20.818326] init: cannot find ‘/system/bin/qrngd’ (No such file or directory), disabling ‘qrngd’
[ 20.824376] type=1400 audit(30.819:9): avc: denied { chown } for pid=733 comm=”ptt_socket_app” capability=0 scontext=u:r:wcnss_service:s0 tcontext=u:r:wcnss_service:s0 tclass=capability permissive=0
[ 20.824522] type=1400 audit(30.819:10): avc: denied { setgid } for pid=733 comm=”ptt_socket_app” capability=6 scontext=u:r:wcnss_service:s0 tcontext=u:r:wcnss_service:s0 tclass=capability permissive=0
[ 20.862592] init: Starting service ‘thermal-engine’…
[ 20.869632] init: Starting service ‘wcnss-service’…
[ 20.876491] init: Starting service ‘imsqmidaemon’…
[ 20.883142] init: Starting service ‘adsprpcd’…
[ 20.889944] init: Starting service ‘energy-awareness’…
[ 20.896965] init: Starting service ‘zygote’…
[ 20.902812] init: Starting service ‘zygote_secondary’…
[ 20.910402] init: Starting service ‘audioserver’…
[ 20.917754] init: Starting service ‘cameraserver’…
[ 20.923560] init: couldn’t write 756 to /dev/cpuset/camera-daemon/tasks: No such file or directory
[ 20.924597] init: Starting service ‘drm’…
[ 20.927529] init: Starting service ‘installd’…
[ 20.930330] init: Starting service ‘keystore’…
[ 20.932885] init: Starting service ‘mediacodec’…
[ 20.935449] init: Starting service ‘mediadrm’…
[ 20.938533] init: Starting service ‘mediaextractor’…
[ 20.939025] type=1400 audit(31.049:11): avc: denied { getattr } for pid=755 comm=”audioserver” path=”/vendor” dev=”rootfs” ino=13904 scontext=u:r:audioserver:s0 tcontext=u:object_r:rootfs:s0 tclass=lnk_file permissive=0
[ 20.941092] init: Starting service ‘media’…
[ 20.943674] init: Starting service ‘netd’…
[ 20.946632] init: Starting service ‘ril-daemon’…
[ 20.952516] type=1400 audit(31.069:12): avc: denied { getattr } for pid=762 comm=”mediadrmserver” path=”/vendor” dev=”rootfs” ino=13904 scontext=u:r:mediadrmserver:s0 tcontext=u:object_r:rootfs:s0 tclass=lnk_file permissive=0
[ 20.954791] init: Service ‘ptt_socket_app’ (pid 733) exited with status 1
[ 20.956175] init: Starting service ‘dpmd’…
[ 20.957073] type=1400 audit(31.069:13): avc: denied { getattr } for pid=761 comm=”mediacodec” path=”/vendor” dev=”rootfs” ino=13904 scontext=u:r:mediacodec:s0 tcontext=u:object_r:rootfs:s0 tclass=lnk_file permissive=0
[ 20.958943] init: Starting service ‘cnss-daemon’…
[ 20.962062] init: Starting service ‘loc_launcher’…
[ 20.964098] init: Starting service ‘qcom-sh’…
[ 20.966528] init: Starting service ‘atfwd’…
[ 20.980591] init: Starting service ‘RIDL’…
[ 20.984006] init: Starting service ‘qseeproxydaemon’…
[ 21.000147] init: cannot find ‘/system/vendor/bin/seemp_healthd’ (No such file or directory), disabling ‘seemp_healthd’
[ 21.002915] init: Starting service ‘qcamerasvr’…
[ 21.004628] init: cannot find ‘/system/bin/qfp-daemon’ (No such file or directory), disabling ‘qfp-daemon’
[ 21.005682] init: Starting service ‘audiod’…
[ 21.007266] init: cannot find ‘/system/bin/dts_configurator’ (No such file or directory), disabling ‘dts_configurator’
[ 21.009633] init: Starting service ‘mdtpd’…
[ 21.015669] init: Starting service ‘gatekeeperd’…
[ 21.032554] init: Starting service ‘perfprofd’…
[ 21.035298] init: cannot find ‘/system/bin/qmuxd’ (No such file or directory), disabling ‘qmuxd’
[ 21.036962] init: Starting service ‘config_bt_addr’…
[ 21.041176] init: Starting service ‘config_bluetooth’…
[ 21.091493] init: Starting service ‘imsdatadaemon’…
[ 21.104704] init: Starting service ‘ipacm-diag’…
[ 21.113970] init: Starting service ‘msm_irqbalance’…
[ 21.151399] init: Service ‘config_bt_addr’ (pid 807) exited with status 0
[ 21.165311] init: Starting service ‘ipacm’…
[ 21.192035] type=1400 audit(31.309:14): avc: denied { getattr } for pid=756 comm=”cameraserver” path=”/vendor” dev=”rootfs” ino=13904 scontext=u:r:cameraserver:s0 tcontext=u:object_r:rootfs:s0 tclass=lnk_file permissive=0
[ 21.271075] init: Starting service ‘ril-daemon2’…
[ 21.458379] init: Starting service ‘qti’…
[ 21.488401] type=1400 audit(31.589:15): avc: denied { net_raw } for pid=826 comm=”imsdatadaemon” capability=13 scontext=u:r:ims:s0 tcontext=u:r:ims:s0 tclass=capability permissive=0
[ 21.601395] init: Starting service ‘netmgrd’…
[ 21.628647] init: property_set(“ro.qualcomm.bluetooth.opp”, “true”) failed
[ 21.635567] init: Service ‘qcom-sh’ (pid 778) exited with status 0
[ 21.686972] init: property_set(“ro.qualcomm.bluetooth.hfp”, “true”) failed
[ 21.721551] vold (592) used greatest stack depth: 9336 bytes left
[ 21.747270] init: Starting service ‘port-bridge’…
[ 21.778482] init: property_set(“ro.qualcomm.bluetooth.hsp”, “true”) failed
[ 21.827768] init: property_set(“ro.qualcomm.bluetooth.pbap”, “true”) failed
[ 21.849328] init: Service ‘qcom-c_main-sh’ (pid 731) exited with status 0
[ 21.883261] init: Service ‘energy-awareness’ (pid 752) exited with status 0
[ 21.914908] init: Service ‘port-bridge’ (pid 894) exited with status 1
[ 21.922300] init: property_set(“ro.qualcomm.bluetooth.ftp”, “true”) failed
[ 21.992994] init: property_set(“ro.qualcomm.bluetooth.nap”, “true”) failed
[ 22.048589] init: property_set(“ro.bluetooth.sap”, “true”) failed
[ 22.082825] init: property_set(“ro.bluetooth.dun”, “true”) failed
[ 22.119739] init: property_set(“ro.qualcomm.bluetooth.map”, “true”) failed
[ 22.149646] init: property_set(“ro.bluetooth.hfp.ver”, “1.7”) failed
[ 22.178160] init: property_set(“ro.qualcomm.bt.hci_transport”, “smd”) failed
[ 22.222875] init: Service ‘config_bluetooth’ (pid 808) exited with status 0
[ 22.457736] diag: In diag_send_feature_mask_update, control channel is not open, p: 2, 0000000000000000
[ 22.633673] wcnss: no space available for smd frame
[ 22.658335] wcnss: no space available for smd frame
[ 22.688383] wcnss: no space available for smd frame
[ 22.718380] wcnss: no space available for smd frame
[ 22.782635] QSEECOM: qseecom_load_app: App (mdtp) does’nt exist, loading apps for first time
[ 22.899816] msm_camera_fill_vreg_params:78 i 1 j 0 cam_vio
[ 22.904275] msm_camera_fill_vreg_params:120 i 3 j 1 cam_vaf
[ 22.910011] msm_camera_fill_vreg_params:120 i 2 j 1 cam_vaf
[ 22.915390] msm_camera_fill_vreg_params:78 i 4 j 0 cam_vio
[ 22.921477] msm_camera_power_up:1420
[ 22.925141] msm_camera_power_up index 0
[ 22.930330] QSEECOM: qseecom_load_app: App with id 131074 (mdtp) now loaded
[ 22.932852] msm_camera_power_up type 1
[ 22.932855] msm_camera_power_up:1489 gpio set val 127
[ 22.934970] msm_camera_power_up index 1
[ 22.934972] msm_camera_power_up type 2
[ 22.935034] 1b0c000.qcom,cci:qcom,camera@0 supply cam_vio not found, using dummy regulator
[ 22.935275] msm_cam_sensor_handle_reg_gpio: 1309 Seq val: 0, config: 1
[ 22.935275] msm_cam_sensor_handle_reg_gpio: 1343 GPIO offset: 5, seq_val: 0
[ 22.935282] msm_camera_power_up index 2
[ 22.935284] msm_camera_power_up type 1
[ 22.935286] msm_camera_power_up:1489 gpio set val 33
[ 22.935289] msm_camera_power_up index 3
[ 22.935291] msm_camera_power_up type 2
[ 22.940228] msm_cam_sensor_handle_reg_gpio: 1309 Seq val: 1, config: 1
[ 22.940228] msm_cam_sensor_handle_reg_gpio: 1343 GPIO offset: 3, seq_val: 1
[ 22.940232] msm_camera_power_up index 4
[ 22.940233] msm_camera_power_up type 0
[ 22.942063] msm_camera_power_up index 5
[ 22.942066] msm_camera_power_up type 1
[ 22.942069] msm_camera_power_up:1489 gpio set val 127
[ 22.946133] msm_camera_power_up exit
[ 22.946137] travies add for power up finish
[ 23.329370] msm_qti_pp_get_rms_value_control, back not active to query rms be_idx:3
[ 23.337278] Watchdog bite received from wcnss!
[ 23.340694] wcnss subsystem failure reason: SFR Init: wdog or kernel error suspected..
[ 23.367804] clock frequency is zero, cannot access PMU or other registers
[ 23.369071] msm_dolby_dap_param_to_get_control_get, port_id not set, do not query ADM
[ 23.371045] msm_dolby_dap_param_visualizer_control_get Incorrect VCNB length
[ 23.373187] msm_voice_sound_focus_get: Error getting Sound Focus Params, err=-22
[ 23.373711] msm_voice_source_tracking_get: Error getting Source Tracking Params, err=-22
[ 23.374200] msm_audio_get_copp_idx_from_port_id: Invalid FE, exiting
[ 23.374203] msm_audio_sound_focus_get: Could not get copp idx for port_id=16385
[ 23.374631] msm_audio_get_copp_idx_from_port_id: Invalid FE, exiting
[ 23.374634] msm_audio_source_tracking_get: Could not get copp idx for port_id=16385
[ 23.375055] msm_voice_sound_focus_get: Error getting Sound Focus Params, err=-22
[ 23.375486] msm_voice_source_tracking_get: Error getting Source Tracking Params, err=-22
[ 23.375878] msm_audio_get_copp_idx_from_port_id: Invalid FE, exiting
[ 23.375881] msm_audio_sound_focus_get: Could not get copp idx for port_id=4101
[ 23.376273] msm_audio_get_copp_idx_from_port_id: Invalid FE, exiting
[ 23.376276] msm_audio_source_tracking_get: Could not get copp idx for port_id=4101
[ 23.384661] msm_pcm_volume_ctl_get substream runtime not found
[ 23.386609] msm_pcm_volume_ctl_get substream runtime not found
[ 23.387874] msm_pcm_volume_ctl_get substream runtime not found
[ 23.388878] msm_compr_audio_effects_config_get: stream or effects inactive
[ 23.392279] msm_pcm_volume_ctl_get substream runtime not found
[ 23.393870] msm_pcm_volume_ctl_get substream runtime not found
[ 23.394246] msm_pcm_volume_ctl_get substream or runtime not found
[ 23.395901] msm_compr_audio_effects_config_get: stream or effects inactive
[ 23.398484] msm_compr_audio_effects_config_get: stream or effects inactive
[ 23.400944] msm_compr_audio_effects_config_get: stream or effects inactive
[ 23.403284] msm_compr_audio_effects_config_get: stream or effects inactive
[ 23.405651] msm_compr_audio_effects_config_get: stream or effects inactive
[ 23.407849] msm_compr_audio_effects_config_get: stream or effects inactive
[ 23.410298] msm_compr_audio_effects_config_get: stream or effects inactive
[ 23.412913] msm_compr_audio_effects_config_get: stream or effects inactive
[ 23.415123] msm_pcm_volume_ctl_get substream or runtime not found
[ 23.452008] QSEECOM: qseecom_unload_app: App id 131074 now unloaded
[ 23.735796] init: property_set(“ro.ril.svlte1x”, “false”) failed
[ 23.742365] init: property_set(“ro.ril.svdo”, “false”) failed
[ 23.778356] wcdcal_hwdep_ioctl_shared: codec didn’t set this 0!!
[ 23.783963] wcdcal_hwdep_ioctl_shared: codec didn’t set this 3!!
[ 23.829275] core_set_license: Invalid cal block to send
[ 23.860559] init: Service ‘RIDL’ (pid 780) exited with status 65
[ 23.938297] * msm_cci_dump_registers : 71 CCI TOP Registers *
[ 23.944224] msm_cci_dump_registers : 76 offset = 0x0 value = 0x10020005
[ 23.950446] msm_cci_dump_registers : 76 offset = 0x4 value = 0x1
[ 23.956224] msm_cci_dump_registers : 76 offset = 0x8 value = 0x2
[ 23.962416] msm_cci_dump_registers : 76 offset = 0xC value = 0x0
[ 23.968248] msm_cci_dump_registers : 76 offset = 0x10 value = 0x0
[ 23.974258] msm_cci_dump_registers : 76 offset = 0x14 value = 0x0
[ 23.980489] msm_cci_dump_registers : 76 offset = 0x18 value = 0x0
[ 23.986415] msm_cci_dump_registers : 76 offset = 0x1C value = 0x0
[ 23.992687] msm_cci_dump_registers : 76 offset = 0x20 value = 0x0
[ 23.998828] msm_cci_dump_registers : 76 offset = 0x24 value = 0x0
[ 24.004644] msm_cci_dump_registers : 76 offset = 0x28 value = 0x0
[ 24.010988] msm_cci_dump_registers : 76 offset = 0x2C value = 0x0
[ 24.016798] msm_cci_dump_registers : 76 offset = 0x30 value = 0x0
[ 24.023031] msm_cci_dump_registers : 76 offset = 0x34 value = 0x0
[ 24.029180] * msm_cci_dump_registers : 81 CCI MASTER0 Registers *
[ 24.035644] msm_cci_dump_registers : 88 offset = 0x100 value = 0x14001C
[ 24.042448] msm_cci_dump_registers : 88 offset = 0x104 value = 0x150015
[ 24.048896] msm_cci_dump_registers : 88 offset = 0x108 value = 0xD0012
[ 24.055338] msm_cci_dump_registers : 88 offset = 0x10C value = 0x20
[ 24.061726] msm_cci_dump_registers : 88 offset = 0x110 value = 0x163
[ 24.067918] msm_cci_dump_registers : 88 offset = 0x114 value = 0x41013010
[ 24.074938] msm_cci_dump_registers : 88 offset = 0x11C value = 0x0
[ 24.080969] * msm_cci_dump_registers : 93 CCI MASTER0 QUEUE1 Registers *
[ 24.088215] msm_cci_dump_registers : 99 offset = 0x400 value = 0x5
[ 24.094312] msm_cci_dump_registers : 99 offset = 0x404 value = 0x2
[ 24.100614] msm_cci_dump_registers : 99 offset = 0x408 value = 0x2B
[ 24.106725] msm_cci_dump_registers : 99 offset = 0x40C value = 0x0
[ 24.113084] msm_cci_dump_registers : 99 offset = 0x410 value = 0x7
[ 24.119145] msm_cci_dump_registers : 99 offset = 0x414 value = 0x2D
[ 24.121290] ipa ipa_sps_irq_control_all:938 EP (5) not allocated.
[ 24.122678] ipa ipa_sps_irq_control_all:938 EP (5) not allocated.
[ 24.125375] ipa-wan ipa_wwan_ioctl:1527 get AGG size 8192 count 10
[ 24.126243] ipa ipa_sps_irq_control_all:938 EP (5) not allocated.
[ 24.129402] ipa ipa_assign_policy:3112 get close-by 8192
[ 24.129407] ipa ipa_assign_policy:3118 set rx_buff_sz 7808
[ 24.129409] ipa ipa_assign_policy:3141 set aggr_limit 6
[ 24.165841] * msm_cci_dump_registers : 104 CCI Interrupt Registers *
[ 24.172787] msm_cci_dump_registers : 109 offset = 0xC00 value = 0x1
[ 24.178950] msm_cci_dump_registers : 109 offset = 0xC04 value = 0x7FFF7FF7
[ 24.184080] ipa-wan ipa_wwan_ioctl:1433 dev(rmnet_data0) register to IPA
[ 24.192608] msm_cci_dump_registers : 109 offset = 0xC08 value = 0x7FFF7FF7
[ 24.199566] msm_cci_dump_registers : 109 offset = 0xC0C value = 0x0
[ 24.205512] msm_cci_dump_registers : 109 offset = 0xC10 value = 0x0
[ 24.211956] msm_cci_dump_registers : 109 offset = 0xC14 value = 0x0
[ 24.218228] msm_cci_dump_registers : 109 offset = 0xC18 value = 0x0
[ 24.224259] msm_cci_i2c_read: 945 wait_for_completion_timeout rc = -110
[ 24.235680] ipa-wan ipa_wwan_ioctl:1433 dev(rmnet_data1) register to IPA
[ 24.277912] ipa-wan ipa_wwan_ioctl:1433 dev(rmnet_data2) register to IPA
[ 24.343572] ipa-wan ipa_wwan_ioctl:1433 dev(rmnet_data3) register to IPA
[ 24.408489] ipa-wan ipa_wwan_ioctl:1433 dev(rmnet_data4) register to IPA
[ 24.449937] ipa-wan ipa_wwan_ioctl:1433 dev(rmnet_data5) register to IPA
[ 24.494797] IPC_RTR: msm_ipc_router_bind: slim_daemon Do not have permissions
[ 24.504148] ipa-wan ipa_wwan_ioctl:1433 dev(rmnet_data6) register to IPA
[ 24.530327] wcnss: no space available for smd frame
[ 24.556438] ipa-wan ipa_wwan_ioctl:1433 dev(rmnet_data7) register to IPA
[ 24.558478] wcnss: no space available for smd frame
[ 24.588337] wcnss: no space available for smd frame
[ 24.618462] wcnss: no space available for smd frame
[ 24.652797] msm_qti_pp_get_rms_value_control, back not active to query rms be_idx:3
[ 24.680856] msm_dolby_dap_param_to_get_control_get, port_id not set, do not query ADM
[ 24.688205] msm_dolby_dap_param_visualizer_control_get Incorrect VCNB length
[ 24.698451] msm_voice_sound_focus_get: Error getting Sound Focus Params, err=-22
[ 24.705800] msm_voice_source_tracking_get: Error getting Source Tracking Params, err=-22
[ 24.713492] msm_audio_get_copp_idx_from_port_id: Invalid FE, exiting
[ 24.719302] msm_audio_sound_focus_get: Could not get copp idx for port_id=16385
[ 24.726949] msm_audio_get_copp_idx_from_port_id: Invalid FE, exiting
[ 24.733119] msm_audio_source_tracking_get: Could not get copp idx for port_id=16385
[ 24.741049] msm_voice_sound_focus_get: Error getting Sound Focus Params, err=-22
[ 24.748498] msm_voice_source_tracking_get: Error getting Source Tracking Params, err=-22
[ 24.756454] msm_audio_get_copp_idx_from_port_id: Invalid FE, exiting
[ 24.762512] msm_audio_sound_focus_get: Could not get copp idx for port_id=4101
[ 24.770051] msm_audio_get_copp_idx_from_port_id: Invalid FE, exiting
[ 24.775813] msm_audio_source_tracking_get: Could not get copp idx for port_id=4101
[ 24.792658] msm_pcm_volume_ctl_get substream runtime not found
[ 24.799716] msm_pcm_volume_ctl_get substream runtime not found
[ 24.805890] msm_pcm_volume_ctl_get substream runtime not found
[ 24.811818] msm_compr_audio_effects_config_get: stream or effects inactive
[ 24.821717] msm_pcm_volume_ctl_get substream runtime not found
[ 24.828589] msm_pcm_volume_ctl_get substream runtime not found
[ 24.833855] msm_pcm_volume_ctl_get substream or runtime not found
[ 24.841584] msm_compr_audio_effects_config_get: stream or effects inactive
[ 24.850564] msm_compr_audio_effects_config_get: stream or effects inactive
[ 24.859295] msm_compr_audio_effects_config_get: stream or effects inactive
[ 24.867873] msm_compr_audio_effects_config_get: stream or effects inactive
[ 24.876766] msm_compr_audio_effects_config_get: stream or effects inactive
[ 24.885651] msm_compr_audio_effects_config_get: stream or effects inactive
[ 24.894353] msm_compr_audio_effects_config_get: stream or effects inactive
[ 24.903209] msm_compr_audio_effects_config_get: stream or effects inactive
[ 24.911514] msm_pcm_volume_ctl_get substream or runtime not found
[ 25.228341] msm_cci_flush_queue:176 wait timeout
[ 25.232236] msm_cci_i2c_read_bytes:1040 failed rc -110
[ 25.237471] msm_camera_cci_i2c_read: line 45 rc = -110
[ 25.242336] msm_sensor_match_id: s5k3l8: read id failed
[ 25.247482] msm_sensor_check_id:1374 match id failed rc -110
[ 25.253162] travies add for check id result is -110
[ 25.257886] msm_camera_power_down:1645
[ 25.262058] msm_camera_power_down index 0
[ 25.265604] msm_camera_power_down type 0
[ 25.273408] Watchdog bite received from wcnss!
[ 25.275862] msm_camera_power_down index 1
[ 25.275864] msm_camera_power_down type 1
[ 25.277992] msm_camera_power_down index 2
[ 25.278065] msm_camera_power_down type 2
[ 25.278275] msm_cam_sensor_handle_reg_gpio: 1309 Seq val: 1, config: 0
[ 25.278275] msm_cam_sensor_handle_reg_gpio: 1343 GPIO offset: 3, seq_val: 1
[ 25.278277] msm_camera_power_down index 3
[ 25.278279] msm_camera_power_down type 1
[ 25.278286] msm_camera_power_down index 4
[ 25.278287] msm_camera_power_down type 2
[ 25.278349] msm_cam_sensor_handle_reg_gpio: 1309 Seq val: 0, config: 0
[ 25.278349] msm_cam_sensor_handle_reg_gpio: 1343 GPIO offset: 5, seq_val: 0
[ 25.278572] msm_camera_power_down exit
[ 25.308251] msm_camera_power_up:1420
[ 25.308902] msm_camera_power_up index 0
[ 25.308904] msm_camera_power_up type 1
[ 25.308907] msm_camera_power_up:1489 gpio set val 127
[ 25.311016] msm_camera_power_up index 1
[ 25.311018] msm_camera_power_up type 2
[ 25.311071] 1b0c000.qcom,cci:qcom,camera@0 supply cam_vio not found, using dummy regulator
[ 25.311299] msm_cam_sensor_handle_reg_gpio: 1309 Seq val: 0, config: 1
[ 25.311300] msm_cam_sensor_handle_reg_gpio: 1343 GPIO offset: 5, seq_val: 0
[ 25.311307] msm_camera_power_up index 2
[ 25.311309] msm_camera_power_up type 1
[ 25.311311] msm_camera_power_up:1489 gpio set val 33
[ 25.311314] msm_camera_power_up index 3
[ 25.311316] msm_camera_power_up type 2
[ 25.404509] wcnss subsystem failure reason: SFR Init: wdog or kernel error suspected..
[ 25.414019] msm_cam_sensor_handle_reg_gpio: 1309 Seq val: 1, config: 1
[ 25.419476] msm_cam_sensor_handle_reg_gpio: 1343 GPIO offset: 3, seq_val: 1
[ 25.426451] msm_camera_power_up index 4
[ 25.430486] msm_camera_power_up type 0
[ 25.431505] clock frequency is zero, cannot access PMU or other registers
[ 25.443019] msm_camera_power_up index 5
[ 25.445837] msm_camera_power_up type 1
[ 25.450306] msm_camera_power_up:1489 gpio set val 127
[ 25.457316] msm_camera_power_up exit
[ 25.460058] travies add for power up finish
[ 26.350408] wcnss: no space available for smd frame
[ 26.378388] wcnss: no space available for smd frame
[ 26.408360] wcnss: no space available for smd frame
[ 26.438323] wcnss: no space available for smd frame
[ 26.458261] * msm_cci_dump_registers : 71 CCI TOP Registers *
[ 26.463579] msm_cci_dump_registers : 76 offset = 0x0 value = 0x10020005
[ 26.470526] msm_cci_dump_registers : 76 offset = 0x4 value = 0x1
[ 26.476163] msm_cci_dump_registers : 76 offset = 0x8 value = 0x2
[ 26.482366] msm_cci_dump_registers : 76 offset = 0xC value = 0x0
[ 26.488250] msm_cci_dump_registers : 76 offset = 0x10 value = 0x0
[ 26.494218] msm_cci_dump_registers : 76 offset = 0x14 value = 0x0
[ 26.500465] msm_cci_dump_registers : 76 offset = 0x18 value = 0x0
[ 26.506374] msm_cci_dump_registers : 76 offset = 0x1C value = 0x0
[ 26.512763] msm_cci_dump_registers : 76 offset = 0x20 value = 0x0
[ 26.518732] msm_cci_dump_registers : 76 offset = 0x24 value = 0x0
[ 26.524743] msm_cci_dump_registers : 76 offset = 0x28 value = 0x0
[ 26.530882] msm_cci_dump_registers : 76 offset = 0x2C value = 0x0
[ 26.536850] msm_cci_dump_registers : 76 offset = 0x30 value = 0x0
[ 26.543023] msm_cci_dump_registers : 76 offset = 0x34 value = 0x0
[ 26.549010] * msm_cci_dump_registers : 81 CCI MASTER0 Registers *
[ 26.555595] msm_cci_dump_registers : 88 offset = 0x100 value = 0x14001C
[ 26.562402] msm_cci_dump_registers : 88 offset = 0x104 value = 0x150015
[ 26.568866] msm_cci_dump_registers : 88 offset = 0x108 value = 0xD0012
[ 26.575296] msm_cci_dump_registers : 88 offset = 0x10C value = 0x20
[ 26.581761] msm_cci_dump_registers : 88 offset = 0x110 value = 0x163
[ 26.587883] msm_cci_dump_registers : 88 offset = 0x114 value = 0x41013010
[ 26.594990] msm_cci_dump_registers : 88 offset = 0x11C value = 0x0
[ 26.601168] * msm_cci_dump_registers : 93 CCI MASTER0 QUEUE1 Registers *
[ 26.608256] msm_cci_dump_registers : 99 offset = 0x400 value = 0x5
[ 26.614473] msm_cci_dump_registers : 99 offset = 0x404 value = 0x2
[ 26.620643] msm_cci_dump_registers : 99 offset = 0x408 value = 0x2B
[ 26.626814] msm_cci_dump_registers : 99 offset = 0x40C value = 0x0
[ 26.633038] msm_cci_dump_registers : 99 offset = 0x410 value = 0x7
[ 26.639521] msm_cci_dump_registers : 99 offset = 0x414 value = 0x2D
[ 26.645264] * msm_cci_dump_registers : 104 CCI Interrupt Registers *
[ 26.652750] msm_cci_dump_registers : 109 offset = 0xC00 value = 0x1
[ 26.659089] msm_cci_dump_registers : 109 offset = 0xC04 value = 0x7FFF7FF7
[ 26.665314] msm_cci_dump_registers : 109 offset = 0xC08 value = 0x7FFF7FF7
[ 26.672576] msm_cci_dump_registers : 109 offset = 0xC0C value = 0x0
[ 26.678657] msm_cci_dump_registers : 109 offset = 0xC10 value = 0x0
[ 26.684680] msm_cci_dump_registers : 109 offset = 0xC14 value = 0x0
[ 26.691423] msm_cci_dump_registers : 109 offset = 0xC18 value = 0x0
[ 26.697200] msm_cci_i2c_read: 945 wait_for_completion_timeout rc = -110
[ 27.078529] Watchdog bite received from wcnss!
[ 27.081942] wcnss subsystem failure reason: SFR Init: wdog or kernel error suspected..
[ 27.108543] clock frequency is zero, cannot access PMU or other registers
[ 27.698317] msm_cci_flush_queue:176 wait timeout
[ 27.702005] msm_cci_i2c_read_bytes:1040 failed rc -110
[ 27.707117] msm_camera_cci_i2c_read: line 45 rc = -110
[ 27.712304] msm_sensor_match_id: s5k3l8: read id failed
[ 27.717353] msm_sensor_check_id:1374 match id failed rc -110
[ 27.723124] travies add for check id result is -110
[ 27.727853] msm_camera_power_down:1645
[ 27.732082] msm_camera_power_down index 0
[ 27.735578] msm_camera_power_down type 0
[ 27.746064] msm_camera_power_down index 1
[ 27.749232] msm_camera_power_down type 1
[ 27.755057] msm_camera_power_down index 2
[ 27.758287] msm_camera_power_down type 2
[ 27.762128] msm_cam_sensor_handle_reg_gpio: 1309 Seq val: 1, config: 0
[ 27.768526] msm_cam_sensor_handle_reg_gpio: 1343 GPIO offset: 3, seq_val: 1
[ 27.775395] msm_camera_power_down index 3
[ 27.779520] msm_camera_power_down type 1
[ 27.783292] msm_camera_power_down index 4
[ 27.787287] msm_camera_power_down type 2
[ 27.791491] msm_cam_sensor_handle_reg_gpio: 1309 Seq val: 0, config: 0
[ 27.797525] msm_cam_sensor_handle_reg_gpio: 1343 GPIO offset: 5, seq_val: 0
[ 27.805147] msm_camera_power_down exit
[ 27.838498] msm_camera_power_up:1420
[ 27.842393] msm_camera_power_up index 0
[ 27.845361] msm_camera_power_up type 1
[ 27.849344] msm_camera_power_up:1489 gpio set val 127
[ 27.856396] msm_camera_power_up index 1
[ 27.859668] msm_camera_power_up type 2
[ 27.863647] 1b0c000.qcom,cci:qcom,camera@0 supply cam_vio not found, using dummy regulator
[ 27.871908] msm_cam_sensor_handle_reg_gpio: 1309 Seq val: 0, config: 1
[ 27.877887] msm_cam_sensor_handle_reg_gpio: 1343 GPIO offset: 5, seq_val: 0
[ 27.884753] msm_camera_power_up index 2
[ 27.888578] msm_camera_power_up type 1
[ 27.892187] msm_camera_power_up:1489 gpio set val 33
[ 27.897147] msm_camera_power_up index 3
[ 27.901139] msm_camera_power_up type 2
[ 27.906286] msm_cam_sensor_handle_reg_gpio: 1309 Seq val: 1, config: 1
[ 27.911820] msm_cam_sensor_handle_reg_gpio: 1343 GPIO offset: 3, seq_val: 1
[ 27.918809] msm_camera_power_up index 4
[ 27.922535] msm_camera_power_up type 0
[ 27.928402] msm_camera_power_up index 5
[ 27.931971] msm_camera_power_up type 1
[ 27.934944] msm_camera_power_up:1489 gpio set val 127
[ 27.943176] msm_camera_power_up exit
[ 27.945840] travies add for power up finish
[ 28.002944] wcnss: no space available for smd frame
[ 28.028560] wcnss: no space available for smd frame
[ 28.058583] wcnss: no space available for smd frame
[ 28.088555] wcnss: no space available for smd frame
[ 28.728286] Watchdog bite received from wcnss!
[ 28.731707] wcnss subsystem failure reason: SFR Init: wdog or kernel error suspected..
[ 28.757510] clock frequency is zero, cannot access PMU or other registers
[ 28.948235] * msm_cci_dump_registers : 71 CCI TOP Registers *
[ 28.953558] msm_cci_dump_registers : 76 offset = 0x0 value = 0x10020005
[ 28.960568] msm_cci_dump_registers : 76 offset = 0x4 value = 0x1
[ 28.966426] msm_cci_dump_registers : 76 offset = 0x8 value = 0x2
[ 28.972509] msm_cci_dump_registers : 76 offset = 0xC value = 0x0
[ 28.978536] msm_cci_dump_registers : 76 offset = 0x10 value = 0x0
[ 28.984197] msm_cci_dump_registers : 76 offset = 0x14 value = 0x0
[ 28.990555] msm_cci_dump_registers : 76 offset = 0x18 value = 0x0
[ 28.996450] msm_cci_dump_registers : 76 offset = 0x1C value = 0x0
[ 29.002623] msm_cci_dump_registers : 76 offset = 0x20 value = 0x0
[ 29.008881] msm_cci_dump_registers : 76 offset = 0x24 value = 0x0
[ 29.014774] msm_cci_dump_registers : 76 offset = 0x28 value = 0x0
[ 29.020893] msm_cci_dump_registers : 76 offset = 0x2C value = 0x0
[ 29.026834] msm_cci_dump_registers : 76 offset = 0x30 value = 0x0
[ 29.033165] msm_cci_dump_registers : 76 offset = 0x34 value = 0x0
[ 29.039215] * msm_cci_dump_registers : 81 CCI MASTER0 Registers *
[ 29.045698] msm_cci_dump_registers : 88 offset = 0x100 value = 0x14001C
[ 29.052484] msm_cci_dump_registers : 88 offset = 0x104 value = 0x150015
[ 29.058899] msm_cci_dump_registers : 88 offset = 0x108 value = 0xD0012
[ 29.065432] msm_cci_dump_registers : 88 offset = 0x10C value = 0x20
[ 29.071760] msm_cci_dump_registers : 88 offset = 0x110 value = 0x163
[ 29.077984] msm_cci_dump_registers : 88 offset = 0x114 value = 0x41013010
[ 29.084801] msm_cci_dump_registers : 88 offset = 0x11C value = 0x0
[ 29.090865] * msm_cci_dump_registers : 93 CCI MASTER0 QUEUE1 Registers *
[ 29.098557] msm_cci_dump_registers : 99 offset = 0x400 value = 0x5
[ 29.104384] msm_cci_dump_registers : 99 offset = 0x404 value = 0x2
[ 29.110723] msm_cci_dump_registers : 99 offset = 0x408 value = 0x2B
[ 29.116663] msm_cci_dump_registers : 99 offset = 0x40C value = 0x0
[ 29.122980] msm_cci_dump_registers : 99 offset = 0x410 value = 0x7
[ 29.129348] msm_cci_dump_registers : 99 offset = 0x414 value = 0x2D
[ 29.135325] * msm_cci_dump_registers : 104 CCI Interrupt Registers *
[ 29.142523] msm_cci_dump_registers : 109 offset = 0xC00 value = 0x1
[ 29.148672] msm_cci_dump_registers : 109 offset = 0xC04 value = 0x7FFF7FF7
[ 29.155292] msm_cci_dump_registers : 109 offset = 0xC08 value = 0x7FFF7FF7
[ 29.162603] msm_cci_dump_registers : 109 offset = 0xC0C value = 0x0
[ 29.168587] msm_cci_dump_registers : 109 offset = 0xC10 value = 0x0
[ 29.174865] msm_cci_dump_registers : 109 offset = 0xC14 value = 0x0
[ 29.181383] msm_cci_dump_registers : 109 offset = 0xC18 value = 0x0
[ 29.187334] msm_cci_i2c_read: 945 wait_for_completion_timeout rc = -110
[ 29.664851] wcnss: no space available for smd frame
[ 29.698576] wcnss: no space available for smd frame
[ 29.728891] wcnss: no space available for smd frame
[ 29.758640] wcnss: no space available for smd frame
[ 30.188364] msm_cci_flush_queue:176 wait timeout
[ 30.192059] msm_cci_i2c_read_bytes:1040 failed rc -110
[ 30.197168] msm_camera_cci_i2c_read: line 45 rc = -110
[ 30.202541] msm_sensor_match_id: s5k3l8: read id failed
[ 30.207398] msm_sensor_check_id:1374 match id failed rc -110
[ 30.213411] travies add for check id result is -110
[ 30.217900] msm_camera_power_down:1645
[ 30.222038] msm_camera_power_down index 0
[ 30.225623] msm_camera_power_down type 0
[ 30.235956] msm_camera_power_down index 1
[ 30.239025] msm_camera_power_down type 1
[ 30.245010] msm_camera_power_down index 2
[ 30.247986] msm_camera_power_down type 2
[ 30.252249] msm_cam_sensor_handle_reg_gpio: 1309 Seq val: 1, config: 0
[ 30.258464] msm_cam_sensor_handle_reg_gpio: 1343 GPIO offset: 3, seq_val: 1
[ 30.265357] msm_camera_power_down index 3
[ 30.269479] msm_camera_power_down type 1
[ 30.273267] msm_camera_power_down index 4
[ 30.277247] msm_camera_power_down type 2
[ 30.281514] msm_cam_sensor_handle_reg_gpio: 1309 Seq val: 0, config: 0
[ 30.287488] msm_cam_sensor_handle_reg_gpio: 1343 GPIO offset: 5, seq_val: 0
[ 30.295116] msm_camera_power_down exit
[ 30.328379] s5k3l8 power up failed
[ 30.331287] MSM-SENSOR-INIT msm_sensor_driver_cmd:82 msm_sensor_driver_cmd failed (non-fatal) rc -110
[ 30.340309] MSM-SENSOR-INIT msm_sensor_init_subdev_do_ioctl:148 msm_sensor_init_subdev_do_ioctl:148 VIDIOC_MSM_SENSOR_INIT_CFG failed (non-fatal)
[ 30.364720] msm_camera_fill_vreg_params:78 i 1 j 0 cam_vio
[ 30.369411] msm_camera_fill_vreg_params:78 i 3 j 0 cam_vio
[ 30.374935] msm_camera_power_up:1420
[ 30.379164] msm_camera_power_up index 0
[ 30.382025] msm_camera_power_up type 1
[ 30.385752] msm_camera_power_up:1489 gpio set val 126
[ 30.393148] msm_camera_power_up index 1
[ 30.393353] Watchdog bite received from wcnss!
[ 30.393363] wcnss subsystem failure reason: SFR Init: wdog or kernel error suspected..
[ 30.408923] msm_camera_power_up type 2
[ 30.412060] 1b0c000.qcom,cci:qcom,camera@1 supply cam_vio not found, using dummy regulator
[ 30.416547] clock frequency is zero, cannot access PMU or other registers
[ 30.427278] msm_cam_sensor_handle_reg_gpio: 1309 Seq val: 0, config: 1
[ 30.433730] msm_cam_sensor_handle_reg_gpio: 1343 GPIO offset: 5, seq_val: 0
[ 30.440854] msm_camera_power_up index 2
[ 30.444307] msm_camera_power_up type 1
[ 30.448363] msm_camera_power_up:1489 gpio set val 122
[ 30.453168] msm_camera_power_up index 3
[ 30.456997] msm_camera_power_up type 0
[ 30.462990] msm_camera_power_up index 4
[ 30.465938] msm_camera_power_up type 1
[ 30.469702] msm_camera_power_up:1489 gpio set val 126
[ 30.477002] msm_camera_power_up exit
[ 30.479673] travies add for power up finish
[ 31.322027] wcnss: no space available for smd frame
[ 31.348389] wcnss: no space available for smd frame
[ 31.379147] wcnss: no space available for smd frame
[ 31.408436] wcnss: no space available for smd frame
[ 31.478489] * msm_cci_dump_registers : 71 CCI TOP Registers *
[ 31.484136] msm_cci_dump_registers : 76 offset = 0x0 value = 0x10020005
[ 31.490633] msm_cci_dump_registers : 76 offset = 0x4 value = 0x1
[ 31.496409] msm_cci_dump_registers : 76 offset = 0x8 value = 0x8
[ 31.502768] msm_cci_dump_registers : 76 offset = 0xC value = 0x0
[ 31.508571] msm_cci_dump_registers : 76 offset = 0x10 value = 0x0
[ 31.514455] msm_cci_dump_registers : 76 offset = 0x14 value = 0x0
[ 31.520982] msm_cci_dump_registers : 76 offset = 0x18 value = 0x0
[ 31.526737] msm_cci_dump_registers : 76 offset = 0x1C value = 0x0
[ 31.533002] msm_cci_dump_registers : 76 offset = 0x20 value = 0x0
[ 31.538899] msm_cci_dump_registers : 76 offset = 0x24 value = 0x0
[ 31.544841] msm_cci_dump_registers : 76 offset = 0x28 value = 0x0
[ 31.551214] msm_cci_dump_registers : 76 offset = 0x2C value = 0x0
[ 31.556996] msm_cci_dump_registers : 76 offset = 0x30 value = 0x0
[ 31.563304] msm_cci_dump_registers : 76 offset = 0x34 value = 0x0
[ 31.569322] * msm_cci_dump_registers : 81 CCI MASTER1 Registers *
[ 31.575833] msm_cci_dump_registers : 88 offset = 0x200 value = 0x14001C
[ 31.582603] msm_cci_dump_registers : 88 offset = 0x204 value = 0x150015
[ 31.589106] msm_cci_dump_registers : 88 offset = 0x208 value = 0xD0012
[ 31.595675] msm_cci_dump_registers : 88 offset = 0x20C value = 0x20
[ 31.602213] msm_cci_dump_registers : 88 offset = 0x210 value = 0x163
[ 31.608530] msm_cci_dump_registers : 88 offset = 0x214 value = 0x41013010
[ 31.615053] msm_cci_dump_registers : 88 offset = 0x21C value = 0x0
[ 31.621225] * msm_cci_dump_registers : 93 CCI MASTER1 QUEUE1 Registers *
[ 31.628677] msm_cci_dump_registers : 99 offset = 0x600 value = 0x5
[ 31.634505] msm_cci_dump_registers : 99 offset = 0x604 value = 0x2
[ 31.640873] msm_cci_dump_registers : 99 offset = 0x608 value = 0x2B
[ 31.646925] msm_cci_dump_registers : 99 offset = 0x60C value = 0x0
[ 31.653395] msm_cci_dump_registers : 99 offset = 0x610 value = 0x7
[ 31.659569] msm_cci_dump_registers : 99 offset = 0x614 value = 0x2D
[ 31.665567] * msm_cci_dump_registers : 104 CCI Interrupt Registers *
[ 31.672592] msm_cci_dump_registers : 109 offset = 0xC00 value = 0x1
[ 31.679048] msm_cci_dump_registers : 109 offset = 0xC04 value = 0x7FFF7FF7
[ 31.685551] msm_cci_dump_registers : 109 offset = 0xC08 value = 0x7FFF7FF7
[ 31.692905] msm_cci_dump_registers : 109 offset = 0xC0C value = 0x0
[ 31.698950] msm_cci_dump_registers : 109 offset = 0xC10 value = 0x0
[ 31.704919] msm_cci_dump_registers : 109 offset = 0xC14 value = 0x0
[ 31.711370] msm_cci_dump_registers : 109 offset = 0xC18 value = 0x0
[ 31.717425] msm_cci_i2c_read: 945 wait_for_completion_timeout rc = -110
[ 32.050341] Watchdog bite received from wcnss!
[ 32.053756] wcnss subsystem failure reason: SFR Init: wdog or kernel error suspected..
[ 32.080026] clock frequency is zero, cannot access PMU or other registers
[ 32.688295] MSM-SENSOR-INIT msm_sensor_wait_for_probe_done:53 msm_sensor_wait_for_probe_done:53 wait timeout
[ 32.688295]
[ 32.699137] MSM-SENSOR-INIT msm_sensor_init_subdev_do_ioctl:148 msm_sensor_init_subdev_do_ioctl:148 VIDIOC_MSM_SENSOR_INIT_CFG failed (non-fatal)
[ 32.718540] msm_cci_flush_queue:176 wait timeout
[ 32.722466] msm_cci_i2c_read_bytes:1040 failed rc -110
[ 32.727259] msm_camera_cci_i2c_read: line 45 rc = -110
[ 32.732538] msm_sensor_match_id: s5k3l8_mono: read id failed
[ 32.738396] msm_sensor_check_id:1374 match id failed rc -110
[ 32.743823] travies add for check id result is -110
[ 32.748744] msm_camera_power_down:1645
[ 32.752917] msm_camera_power_down index 0
[ 32.756350] msm_camera_power_down type 0
[ 32.767330] msm_camera_power_down index 1
[ 32.770451] msm_camera_power_down type 1
[ 32.776535] msm_camera_power_down index 2
[ 32.779620] msm_camera_power_down type 1
[ 32.783425] msm_camera_power_down index 3
[ 32.787424] msm_camera_power_down type 2
[ 32.791648] msm_cam_sensor_handle_reg_gpio: 1309 Seq val: 0, config: 0
[ 32.797656] msm_cam_sensor_handle_reg_gpio: 1343 GPIO offset: 5, seq_val: 0
[ 32.805273] msm_camera_power_down exit
[ 32.838562] msm_camera_power_up:1420
[ 32.841907] msm_camera_power_up index 0
[ 32.844921] msm_camera_power_up type 1
[ 32.849043] msm_camera_power_up:1489 gpio set val 126
[ 32.855891] msm_camera_power_up index 1
[ 32.858934] msm_camera_power_up type 2
[ 32.862514] 1b0c000.qcom,cci:qcom,camera@1 supply cam_vio not found, using dummy regulator
[ 32.871334] msm_cam_sensor_handle_reg_gpio: 1309 Seq val: 0, config: 1
[ 32.877022] msm_cam_sensor_handle_reg_gpio: 1343 GPIO offset: 5, seq_val: 0
[ 32.884374] msm_camera_power_up index 2
[ 32.887952] msm_camera_power_up type 1
[ 32.891887] msm_camera_power_up:1489 gpio set val 122
[ 32.896834] msm_camera_power_up index 3
[ 32.900818] msm_camera_power_up type 0
[ 32.906562] msm_camera_power_up index 4
[ 32.909866] msm_camera_power_up type 1
[ 32.913106] msm_camera_power_up:1489 gpio set val 126
[ 32.922120] msm_camera_power_up exit
[ 32.924669] travies add for power up finish
[ 33.106340] wcnss: no space available for smd frame
[ 33.138452] wcnss: no space available for smd frame
[ 33.168536] wcnss: no space available for smd frame
[ 33.198512] wcnss: no space available for smd frame
[ 33.831371] Watchdog bite received from wcnss!
[ 33.834802] wcnss subsystem failure reason: SFR Init: wdog or kernel error suspected..
[ 33.862547] clock frequency is zero, cannot access PMU or other registers
[ 33.928493] * msm_cci_dump_registers : 71 CCI TOP Registers *
[ 33.933838] msm_cci_dump_registers : 76 offset = 0x0 value = 0x10020005
[ 33.940690] msm_cci_dump_registers : 76 offset = 0x4 value = 0x1
[ 33.946414] msm_cci_dump_registers : 76 offset = 0x8 value = 0x8
[ 33.952626] msm_cci_dump_registers : 76 offset = 0xC value = 0x0
[ 33.958517] msm_cci_dump_registers : 76 offset = 0x10 value = 0x0
[ 33.964467] msm_cci_dump_registers : 76 offset = 0x14 value = 0x0
[ 33.970837] msm_cci_dump_registers : 76 offset = 0x18 value = 0x0
[ 33.976621] msm_cci_dump_registers : 76 offset = 0x1C value = 0x0
[ 33.983242] msm_cci_dump_registers : 76 offset = 0x20 value = 0x0
[ 33.989247] msm_cci_dump_registers : 76 offset = 0x24 value = 0x0
[ 33.994955] msm_cci_dump_registers : 76 offset = 0x28 value = 0x0
[ 34.001111] msm_cci_dump_registers : 76 offset = 0x2C value = 0x0
[ 34.007015] msm_cci_dump_registers : 76 offset = 0x30 value = 0x0
[ 34.013291] msm_cci_dump_registers : 76 offset = 0x34 value = 0x0
[ 34.019255] * msm_cci_dump_registers : 81 CCI MASTER1 Registers *
[ 34.025857] msm_cci_dump_registers : 88 offset = 0x200 value = 0x14001C
[ 34.032800] msm_cci_dump_registers : 88 offset = 0x204 value = 0x150015
[ 34.039116] msm_cci_dump_registers : 88 offset = 0x208 value = 0xD0012
[ 34.045545] msm_cci_dump_registers : 88 offset = 0x20C value = 0x20
[ 34.052159] msm_cci_dump_registers : 88 offset = 0x210 value = 0x163
[ 34.058398] msm_cci_dump_registers : 88 offset = 0x214 value = 0x41013010
[ 34.065208] msm_cci_dump_registers : 88 offset = 0x21C value = 0x0
[ 34.071169] * msm_cci_dump_registers : 93 CCI MASTER1 QUEUE1 Registers *
[ 34.078831] msm_cci_dump_registers : 99 offset = 0x600 value = 0x5
[ 34.084536] msm_cci_dump_registers : 99 offset = 0x604 value = 0x2
[ 34.091100] msm_cci_dump_registers : 99 offset = 0x608 value = 0x2B
[ 34.096938] msm_cci_dump_registers : 99 offset = 0x60C value = 0x0
[ 34.103474] msm_cci_dump_registers : 99 offset = 0x610 value = 0x7
[ 34.109479] msm_cci_dump_registers : 99 offset = 0x614 value = 0x2D
[ 34.115517] * msm_cci_dump_registers : 104 CCI Interrupt Registers *
[ 34.122823] msm_cci_dump_registers : 109 offset = 0xC00 value = 0x1
[ 34.128820] msm_cci_dump_registers : 109 offset = 0xC04 value = 0x7FFF7FF7
[ 34.135566] msm_cci_dump_registers : 109 offset = 0xC08 value = 0x7FFF7FF7
[ 34.142712] msm_cci_dump_registers : 109 offset = 0xC0C value = 0x0
[ 34.148784] msm_cci_dump_registers : 109 offset = 0xC10 value = 0x0
[ 34.154913] msm_cci_dump_registers : 109 offset = 0xC14 value = 0x0
[ 34.161455] msm_cci_dump_registers : 109 offset = 0xC18 value = 0x0
[ 34.167419] msm_cci_i2c_read: 945 wait_for_completion_timeout rc = -110
[ 34.905477] wcnss: no space available for smd frame
[ 34.938485] wcnss: no space available for smd frame
[ 34.968502] wcnss: no space available for smd frame
[ 34.998396] wcnss: no space available for smd frame
[ 35.084590] init: Service ‘bootanim’ (pid 697) exited with status 0
[ 35.168450] msm_cci_flush_queue:176 wait timeout
[ 35.172090] msm_cci_i2c_read_bytes:1040 failed rc -110
[ 35.177175] msm_camera_cci_i2c_read: line 45 rc = -110
[ 35.182498] msm_sensor_match_id: s5k3l8_mono: read id failed
[ 35.187937] msm_sensor_check_id:1374 match id failed rc -110
[ 35.193740] travies add for check id result is -110
[ 35.198542] msm_camera_power_down:1645
[ 35.202569] msm_camera_power_down index 0
[ 35.206157] msm_camera_power_down type 0
[ 35.216493] msm_camera_power_down index 1
[ 35.219567] msm_camera_power_down type 1
[ 35.225666] msm_camera_power_down index 2
[ 35.228747] msm_camera_power_down type 1
[ 35.232576] msm_camera_power_down index 3
[ 35.236550] msm_camera_power_down type 2
[ 35.240830] msm_cam_sensor_handle_reg_gpio: 1309 Seq val: 0, config: 0
[ 35.246789] msm_cam_sensor_handle_reg_gpio: 1343 GPIO offset: 5, seq_val: 0
[ 35.254445] msm_camera_power_down exit
[ 35.278840] msm_camera_power_up:1420
[ 35.282234] msm_camera_power_up index 0
[ 35.284268] init: Starting service ‘qcom-post-boot’…
[ 35.286762] init: Starting service ‘qti-testscripts’…
[ 35.289202] init: cannot find ‘/system/bin/qrngp’ (No such file or directory), disabling ‘qrngp’
[ 35.289302] init: Starting service ‘cs-post-boot’…
[ 35.294085] init: Starting service ‘exec 7 (/system/bin/bootstat)’…
[ 35.302261] type=1400 audit(45.409:16): avc: denied { getattr } for pid=2067 comm=”bootstat” path=”/vendor” dev=”rootfs” ino=13904 scontext=u:r:bootstat:s0 tcontext=u:object_r:rootfs:s0 tclass=lnk_file permissive=0
[ 35.334893] msm_camera_power_up type 1
[ 35.338817] msm_camera_power_up:1489 gpio set val 126
[ 35.345692] msm_camera_power_up index 1
[ 35.348784] msm_camera_power_up type 2
[ 35.351416] init: Service ‘exec 7 (/system/bin/bootstat)’ (pid 2067) exited with status 0
[ 35.353027] init: Starting service ‘exec 8 (/system/bin/bootstat)’…
[ 35.355651] init: Service ‘qti-testscripts’ (pid 2063) exited with status 0
[ 35.362189] type=1400 audit(45.479:17): avc: denied { getattr } for pid=2076 comm=”bootstat” path=”/vendor” dev=”rootfs” ino=13904 scontext=u:r:bootstat:s0 tcontext=u:object_r:rootfs:s0 tclass=lnk_file permissive=0
[ 35.367927] init: Service ‘cs-post-boot’ (pid 2066) exited with status 0
[ 35.384465] init: Service ‘exec 8 (/system/bin/bootstat)’ (pid 2076) exited with status 0
[ 35.385828] init: Starting service ‘exec 9 (/system/bin/bootstat)’…
[ 35.395447] type=1400 audit(45.509:18): avc: denied { getattr } for pid=2080 comm=”bootstat” path=”/vendor” dev=”rootfs” ino=13904 scontext=u:r:bootstat:s0 tcontext=u:object_r:rootfs:s0 tclass=lnk_file permissive=0
[ 35.413550] init: Service ‘exec 9 (/system/bin/bootstat)’ (pid 2080) exited with status 0
[ 35.414345] init: Starting service ‘exec 10 (/system/bin/bootstat)’…
[ 35.433313] type=1400 audit(45.549:19): avc: denied { getattr } for pid=2083 comm=”bootstat” path=”/vendor” dev=”rootfs” ino=13904 scontext=u:r:bootstat:s0 tcontext=u:object_r:rootfs:s0 tclass=lnk_file permissive=0
[ 35.451344] type=1400 audit(45.569:20): avc: denied { write } for pid=2062 comm=”sh” name=”interactive” dev=”sysfs” ino=42217 scontext=u:r:qti_init_shell:s0 tcontext=u:object_r:sysfs:s0 tclass=dir permissive=0
[ 35.486124] 1b0c000.qcom,cci:qcom,camera@1 supply cam_vio not found, using dummy regulator
[ 35.496160] msm_cam_sensor_handle_reg_gpio: 1309 Seq val: 0, config: 1
[ 35.502130] msm_cam_sensor_handle_reg_gpio: 1343 GPIO offset: 5, seq_val: 0
[ 35.507142] init: Service ‘exec 10 (/system/bin/bootstat)’ (pid 2083) exited with status 0
[ 35.517494] msm_camera_power_up index 2
[ 35.520929] msm_camera_power_up type 1
[ 35.524395] msm_camera_power_up:1489 gpio set val 122
[ 35.529770] msm_camera_power_up index 3
[ 35.533398] msm_camera_power_up type 0
[ 35.538948] msm_camera_power_up index 4
[ 35.541756] msm_camera_power_up type 1
[ 35.545486] msm_camera_power_up:1489 gpio set val 126
[ 35.555024] msm_camera_power_up exit
[ 35.557566] travies add for power up finish
[ 35.630897] Watchdog bite received from wcnss!
[ 35.634325] wcnss subsystem failure reason: SFR Init: wdog or kernel error suspected..
[ 35.666717] clock frequency is zero, cannot access PMU or other registers
[ 36.373381] devbw soc:qcom,cpubw: dev_pm_opp_get_opp_count: device OPP not found (-19)
[ 36.392457] init: cannot find ‘/system/vendor/bin/gamed’ (No such file or directory), disabling ‘gamed’
[ 36.422680] type=1400 audit(46.529:21): avc: denied { open } for pid=2137 comm=”perfd” path=”/dev/cpuset/top-app/cpus” dev=”tmpfs” ino=6768 scontext=u:r:perfd:s0 tcontext=u:object_r:device:s0 tclass=file permissive=0
[ 36.454662] type=1400 audit(46.529:22): avc: denied { open } for pid=2137 comm=”perfd” path=”/dev/cpuset/foreground/cpus” dev=”tmpfs” ino=6756 scontext=u:r:perfd:s0 tcontext=u:object_r:device:s0 tclass=file permissive=0
[ 36.473956] type=1400 audit(46.529:23): avc: denied { open } for pid=2137 comm=”perfd” path=”/dev/cpuset/system-background/cpus” dev=”tmpfs” ino=6765 scontext=u:r:perfd:s0 tcontext=u:object_r:device:s0 tclass=file permissive=0
[ 36.493902] type=1400 audit(46.529:24): avc: denied { open } for pid=2137 comm=”perfd” path=”/dev/cpuset/background/cpus” dev=”tmpfs” ino=6762 scontext=u:r:perfd:s0 tcontext=u:object_r:device:s0 tclass=file permissive=0
[ 36.558364] * msm_cci_dump_registers : 71 CCI TOP Registers *
[ 36.563911] msm_cci_dump_registers : 76 offset = 0x0 value = 0x10020005
[ 36.570770] msm_cci_dump_registers : 76 offset = 0x4 value = 0x1
[ 36.576357] msm_cci_dump_registers : 76 offset = 0x8 value = 0x8
[ 36.582642] msm_cci_dump_registers : 76 offset = 0xC value = 0x0
[ 36.588700] msm_cci_dump_registers : 76 offset = 0x10 value = 0x0
[ 36.594730] msm_cci_dump_registers : 76 offset = 0x14 value = 0x0
[ 36.600964] msm_cci_dump_registers : 76 offset = 0x18 value = 0x0
[ 36.606608] msm_cci_dump_registers : 76 offset = 0x1C value = 0x0
[ 36.613042] msm_cci_dump_registers : 76 offset = 0x20 value = 0x0
[ 36.618961] msm_cci_dump_registers : 76 offset = 0x24 value = 0x0
[ 36.624761] msm_cci_dump_registers : 76 offset = 0x28 value = 0x0
[ 36.631421] msm_cci_dump_registers : 76 offset = 0x2C value = 0x0
[ 36.636932] msm_cci_dump_registers : 76 offset = 0x30 value = 0x0
[ 36.643317] msm_cci_dump_registers : 76 offset = 0x34 value = 0x0
[ 36.649507] * msm_cci_dump_registers : 81 CCI MASTER1 Registers *
[ 36.655758] msm_cci_dump_registers : 88 offset = 0x200 value = 0x14001C
[ 36.663098] msm_cci_dump_registers : 88 offset = 0x204 value = 0x150015
[ 36.669947] msm_cci_dump_registers : 88 offset = 0x208 value = 0xD0012
[ 36.675897] msm_cci_dump_registers : 88 offset = 0x20C value = 0x20