iwconfig手册页

$ man iwconfig
IWCONFIG(8)                                             Linux Programmer's Manual                                             IWCONFIG(8)

NAME


       iwconfig - configure a wireless network interface

SYNOPSIS


       iwconfig [interface]
       iwconfig interface [essid X] [nwid N] [mode M] [freq F]
                          [channel C][sens S ][ap A ][nick NN ]
                          [rate R] [rts RT] [frag FT] [txpower T]
                          [enc E] [key K] [power P] [retry R]
                          [modu M] [commit]
       iwconfig --help
       iwconfig --version

DESCRIPTION


       Iwconfig  is  similar to ifconfig(8), but is dedicated to the wireless interfaces. It is used to set the parameters of the network
       interface which are specific to the wireless operation (for example : the frequency).  Iwconfig may also be used to display  those
       parameters, and the wireless statistics (extracted from /proc/net/wireless).

       All  these  parameters  and statistics are device dependent. Each driver will provide only some of them depending on hardware sup‐
       port, and the range of values may change. Please refer to the man page of each device for details.

PARAMETERS


       essid  Set the ESSID (or Network Name - in some products it may also be called Domain ID). The ESSID is  used  to  identify  cells
              which are part of the same virtual network.
              As opposed to the AP Address or NWID which define a single cell, the ESSID defines a group of cells connected via repeaters
              or infrastructure, where the user may roam transparently.
              With some cards, you may disable the ESSID checking (ESSID promiscuous) with off or any (and on to reenable it).
              If the ESSID of your network is one of the special keywords (off, on or any), you should use -- to escape it.
              Examples :
                   iwconfig eth0 essid any
                   iwconfig eth0 essid "My Network"
                   iwconfig eth0 essid -- "ANY"

       nwid   Set the Network ID. As all adjacent wireless networks share the same medium, this parameter is used to  differentiate  them
              (create logical colocated networks) and identify nodes belonging to the same cell.
              This parameter is only used for pre-802.11 hardware, the 802.11 protocol uses the ESSID and AP Address for this function.
              With some cards, you may disable the Network ID checking (NWID promiscuous) with off (and on to reenable it).
              Examples :
                   iwconfig eth0 nwid AB34
                   iwconfig eth0 nwid off

       nick[name]
              Set  the  nickname,  or  the  station name. Some 802.11 products do define it, but this is not used as far as the protocols
              (MAC, IP, TCP) are concerned and completely useless as far as configuration goes. Only some wireless diagnostic  tools  may
              use it.
              Example :
                   iwconfig eth0 nickname "My Linux Node"

       mode   Set  the  operating  mode of the device, which depends on the network topology. The mode can be Ad-Hoc (network composed of
              only one cell and without Access Point), Managed (node connects to a network composed of many Access Points, with roaming),
              Master  (the  node  is  the synchronisation master or acts as an Access Point), Repeater (the node forwards packets between
              other wireless nodes), Secondary (the node acts as a backup master/repeater), Monitor (the node is not associated with  any
              cell and passively monitor all packets on the frequency) or Auto.
              Example :
                   iwconfig eth0 mode Managed
                   iwconfig eth0 mode Ad-Hoc

       freq/channel
              Set  the  operating frequency or channel in the device. A value below 1000 indicates a channel number, a value greater than
              1000 is a frequency in Hz. You may append the suffix k, M or G to the value (for example, "2.46G" for 2.46 GHz  frequency),
              or add enough '0'.
              Channels are usually numbered starting at 1, and you may use iwlist(8) to get the total number of channels, list the avail‐
              able frequencies, and display the current frequency as a channel. Depending on regulations, some  frequencies/channels  may
              not be available.
              When using Managed mode, most often the Access Point dictates the channel and the driver may refuse the setting of the fre‐
              quency. In Ad-Hoc mode, the frequency setting may only be used at initial cell creation, and may be ignored when joining an
              existing cell.
              You may also use off or auto to let the card pick up the best channel (when supported).
              Examples :
                   iwconfig eth0 freq 2422000000
                   iwconfig eth0 freq 2.422G
                   iwconfig eth0 channel 3
                   iwconfig eth0 channel auto

       ap     Force  the  card to register to the Access Point given by the address, if it is possible. This address is the cell identity
              of the Access Point, as reported by wireless scanning, which may be different from its network MAC address. If the wireless
              link  is  point to point, set the address of the other end of the link. If the link is ad-hoc, set the cell identity of the
              ad-hoc network.
              When the quality of the connection goes too low, the driver may revert back to automatic mode (the card  selects  the  best
              Access Point in range).
              You  may  also use off to re-enable automatic mode without changing the current Access Point, or you may use any or auto to
              force the card to reassociate with the currently best Access Point.
              Example :
                   iwconfig eth0 ap 00:60:1D:01:23:45
                   iwconfig eth0 ap any
                   iwconfig eth0 ap off

       rate/bit[rate]
              For cards supporting multiple bit rates, set the bit-rate in b/s. The bit-rate is the speed at which bits  are  transmitted
              over the medium, the user speed of the link is lower due to medium sharing and various overhead.
              You  may append the suffix k, M or G to the value (decimal multiplier : 10^3, 10^6 and 10^9 b/s), or add enough '0'. Values
              below 1000 are card specific, usually an index in the bit-rate list. Use auto to select automatic bit-rate  mode  (fallback
              to  lower  rate  on noisy channels), which is the default for most cards, and fixed to revert back to fixed setting. If you
              specify a bit-rate value and append auto, the driver will use all bit-rates lower and equal than this value.
              Examples :
                   iwconfig eth0 rate 11M
                   iwconfig eth0 rate auto
                   iwconfig eth0 rate 5.5M auto

       txpower
              For cards supporting multiple transmit powers, sets the transmit power in dBm. If W is the power in Watt, the power in  dBm
              is P = 30 + 10.log(W).  If the value is postfixed by mW, it will be automatically converted to dBm.
              In  addition,  on  and off enable and disable the radio, and auto and fixed enable and disable power control (if those fea‐
              tures are available).
              Examples :
                   iwconfig eth0 txpower 15
                   iwconfig eth0 txpower 30mW
                   iwconfig eth0 txpower auto
                   iwconfig eth0 txpower off

       sens   Set the sensitivity threshold. This define how sensitive is the card to poor operating conditions  (low  signal,  interfer‐
              ence). Positive values are assumed to be the raw value used by the hardware or a percentage, negative values are assumed to
              be dBm. Depending on the hardware implementation, this parameter may control various functions.
              On modern cards, this parameter usually control handover/roaming threshold, the lowest signal level for which the  hardware
              remains  associated  with the current Access Point. When the signal level goes below this threshold the card starts looking
              for a new/better Access Point. Some cards may use the number of missed beacons to trigger this. For high density of  Access
              Points,  a  higher  threshold  make  sure  the  card is always associated with the best AP, for low density of APs, a lower
              threshold minimise the number of failed handoffs.
              On more ancient card this parameter usually controls the defer threshold, the lowest signal level for  which  the  hardware
              considers the channel busy. Signal levels above this threshold make the hardware inhibits its own transmission whereas sig‐
              nals weaker than this are ignored and the hardware is free to transmit. This is usually  strongly  linked  to  the  receive
              threshold,  the  lowest  signal  level for which the hardware attempts packet reception. Proper setting of these thresholds
              prevent the card to waste time on background noise while still receiving weak transmissions. Modern designs seems  to  con‐
              trol those thresholds automatically.
              Example :
                   iwconfig eth0 sens -80
                   iwconfig eth0 sens 2

       retry  Most cards have MAC retransmissions, and some allow to set the behaviour of the retry mechanism.
              To set the maximum number of retries, enter limit `value'.  This is an absolute value (without unit), and the default (when
              nothing is specified).  To set the maximum length of time the MAC should retry, enter lifetime `value'.  By defaults,  this
              value in in seconds, append the suffix m or u to specify values in milliseconds or microseconds.
              You can also add the short, long, min and max modifiers. If the card supports automatic mode, they define the bounds of the
              limit or lifetime. Some other cards define different values depending on packet size, for example in 802.11  min  limit  is
              the short retry limit (non RTS/CTS packets).
              Examples :
                   iwconfig eth0 retry 16
                   iwconfig eth0 retry lifetime 300m
                   iwconfig eth0 retry short 12
                   iwconfig eth0 retry min limit 8

       rts[_threshold]
              RTS/CTS  adds  a  handshake before each packet transmission to make sure that the channel is clear. This adds overhead, but
              increases performance in case of hidden nodes or a large number of active nodes. This parameter sets the size of the small‐
              est packet for which the node sends RTS ; a value equal to the maximum packet size disables the mechanism. You may also set
              this parameter to auto, fixed or off.
              Examples :
                   iwconfig eth0 rts 250
                   iwconfig eth0 rts off

       frag[mentation_threshold]
              Fragmentation allows to split an IP packet in a burst of smaller fragments transmitted on the medium. In  most  cases  this
              adds overhead, but in a very noisy environment this reduces the error penalty and allow packets to get through interference
              bursts. This parameter sets the maximum fragment size which is always lower than the maximum packet size.
              This parameter may also control Frame Bursting available on some cards, the ability to send multiple IP  packets  together.
              This mechanism would be enabled if the fragment size is larger than the maximum packet size.
              You may also set this parameter to auto, fixed or off.
              Examples :
                   iwconfig eth0 frag 512
                   iwconfig eth0 frag off

       key/enc[ryption]
              Used to manipulate encryption or scrambling keys and security mode.
              To set the current encryption key, just enter the key in hex digits as XXXX-XXXX-XXXX-XXXX or XXXXXXXX.  To set a key other
              than the current key, prepend or append [index] to the key itself (this won't change which is the active key). You can also
              enter the key as an ASCII string by using the s: prefix. Passphrase is currently not supported.
              To change which key is the currently active key, just enter [index] (without entering any key value).
              off and on disable and reenable encryption.
              The  security  mode  may  be open or restricted, and its meaning depends on the card used. With most cards, in open mode no
              authentication is used and the card may also accept non-encrypted sessions, whereas in restricted mode only encrypted  ses‐
              sions are accepted and the card will use authentication if available.
              If  you  need  to set multiple keys, or set a key and change the active key, you need to use multiple key directives. Argu‐
              ments can be put in any order, the last one will take precedence.
              Examples :
                   iwconfig eth0 key 0123-4567-89
                   iwconfig eth0 key [3] 0123-4567-89
                   iwconfig eth0 key s:password [2]
                   iwconfig eth0 key [2]
                   iwconfig eth0 key open
                   iwconfig eth0 key off
                   iwconfig eth0 key restricted [3] 0123456789
                   iwconfig eth0 key 01-23 key 45-67 [4] key [4]

       power  Used to manipulate power management scheme parameters and mode.
              To set the period between wake ups, enter period `value'.  To set the timeout before going back  to  sleep,  enter  timeout
              `value'.   To  set the generic level of power saving, enter saving `value'.  You can also add the min and max modifiers. By
              default, those values are in seconds, append the suffix m or u to specify values in  milliseconds  or  microseconds.  Some‐
              times, those values are without units (number of beacon periods, dwell, percentage or similar).
              off  and on disable and reenable power management. Finally, you may set the power management mode to all (receive all pack‐
              ets), unicast (receive unicast packets only, discard multicast and broadcast) and multicast (receive multicast  and  broad‐
              cast only, discard unicast packets).
              Examples :
                   iwconfig eth0 power period 2
                   iwconfig eth0 power 500m unicast
                   iwconfig eth0 power timeout 300u all
                   iwconfig eth0 power saving 3
                   iwconfig eth0 power off
                   iwconfig eth0 power min period 2 power max period 4

       modu[lation]
              Force  the  card  to  use a specific set of modulations. Modern cards support various modulations, some which are standard,
              such as 802.11b or 802.11g, and some proprietary. This command force the card to only use the specific set  of  modulations
              listed on the command line. This can be used to fix interoperability issues.
              The  list  of available modulations depend on the card/driver and can be displayed using iwlist modulation.  Note that some
              card/driver may not be able to select each modulation listed independantly, some may come as a group. You may also set this
              parameter to auto let the card/driver do its best.
              Examples :
                   iwconfig eth0 modu 11g
                   iwconfig eth0 modu CCK OFDMa
                   iwconfig eth0 modu auto

       commit Some  cards  may  not apply changes done through Wireless Extensions immediately (they may wait to aggregate the changes or
              apply it only when the card is brought up via ifconfig).  This command (when available) forces the card to apply all  pend‐
              ing changes.
              This is normally not needed, because the card will eventually apply the changes, but can be useful for debugging.

DISPLAY


       For  each  device  which supports wireless extensions, iwconfig will display the name of the MAC protocol used (name of device for
       proprietary protocols), the ESSID (Network Name), the NWID, the frequency (or channel), the sensitivity, the  mode  of  operation,
       the  Access  Point address, the bit-rate, the RTS threshold, the fragmentation threshold, the encryption key and the power manage‐
       ment settings (depending on availability).

       The parameters displayed have the same meaning and values as the parameters you can set, please refer to the previous part  for  a
       detailed explanation of them.
       Some parameters are only displayed in short/abbreviated form (such as encryption). You may use iwlist(8) to get all the details.
       Some parameters have two modes (such as bitrate). If the value is prefixed by `=', it means that the parameter is fixed and forced
       to that value, if it is prefixed by `:', the parameter is in automatic mode and the current value is shown (and may change).

       Access Point/Cell
              An address equal to 00:00:00:00:00:00 means that the card failed to associate with an Access Point (most likely a  configu‐
              ration  issue).  The Access Point parameter will be shown as Cell in ad-hoc mode (for obvious reasons), but otherwise works
              the same.

       If /proc/net/wireless exists, iwconfig will also display its content. Note that those values will depend on  the  driver  and  the
       hardware specifics, so you need to refer to your driver documentation for proper interpretation of those values.

       Link quality
              Overall quality of the link. May be based on the level of contention or interference, the bit or frame error rate, how good
              the received signal is, some timing synchronisation, or other hardware metric. This is  an  aggregate  value,  and  depends
              totally on the driver and hardware.

       Signal level
              Received  signal  strength  (RSSI - how strong the received signal is). May be arbitrary units or dBm, iwconfig uses driver
              meta information to interpret the raw value given by /proc/net/wireless and display the proper unit or maximum value (using
              8 bit arithmetic). In Ad-Hoc mode, this may be undefined and you should use iwspy.

       Noise level
              Background noise level (when no packet is transmitted). Similar comments as for Signal level.

       Rx invalid nwid
              Number  of packets received with a different NWID or ESSID. Used to detect configuration problems or adjacent network exis‐
              tence (on the same frequency).

       Rx invalid crypt
              Number of packets that the hardware was unable to decrypt. This can be used to detect invalid encryption settings.

       Rx invalid frag
              Number of packets for which the hardware was not able to properly re-assemble the link layer fragments (most likely one was
              missing).

       Tx excessive retries
              Number  of  packets  that the hardware failed to deliver. Most MAC protocols will retry the packet a number of times before
              giving up.

       Invalid misc
              Other packets lost in relation with specific wireless operations.

       Missed beacon
              Number of periodic beacons from the Cell or the Access Point we have missed. Beacons are sent at regular intervals to main‐
              tain the cell coordination, failure to receive them usually indicates that the card is out of range.

AUTHOR


       Jean Tourrilhes - [email protected]

FILES


       /proc/net/wireless

SEE ALSO


       ifconfig(8), iwspy(8), iwlist(8), iwevent(8), iwpriv(8), wireless(7).

wireless-tools                                                30 March 2006                                                   IWCONFIG(8)

 

你可能感兴趣的:(无线命令)