DMA的存储器到外设的配置,其实和存储器到存储器的配置非常类似。
只是需要注意一点,就是外设寄存器的地址如何获得?比如USART->DR数据寄存器,我们可以这样定义(基址 + 偏移)
// 外设寄存器地址
#define USART_DR_ADDRESS (USART1_BASE + 0x04)
然后的配置就跟USART和DMA非常类似,直接上初始化过程:
bsp_dma.c
#include "bsp_dma.h"
#include
uint8_t SendBuff[SENDBUFF_SIZE];
void USART_Config(void)
{
GPIO_InitTypeDef GPIO_InitStruct;
USART_InitTypeDef USART_InitStruct;
// 开启串口的GPIO时钟
DEBUG_UASRT_GPIO_APBxClkCmd(DEBUG_UASRT_GPIO_CLK, ENABLE);
// USART的TX配置为复用推挽输出
GPIO_InitStruct.GPIO_Pin = DEBUG_UASRT_TX_GPIO_PIN;
GPIO_InitStruct.GPIO_Mode = GPIO_Mode_AF_PP;
GPIO_InitStruct.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_Init(DEBUG_UASRT_TX_GPIO_PORT, &GPIO_InitStruct);
// USART的RX配置为浮空输入(由中文参考手册查询)
GPIO_InitStruct.GPIO_Pin = DEBUG_UASRT_RX_GPIO_PIN;
GPIO_InitStruct.GPIO_Mode = GPIO_Mode_IN_FLOATING;
GPIO_Init(DEBUG_UASRT_RX_GPIO_PORT, &GPIO_InitStruct);
// 开启串口时钟
DEBUG_USART_APBxClkCmd(DEBUG_USART_CLK, ENABLE);
// 配置串口参数(波特率、8位数据、1位停止位、无校验、发送接收模式、无硬件流控)
USART_InitStruct.USART_BaudRate = DEBUG_USART_BAUDRATE;
USART_InitStruct.USART_WordLength = USART_WordLength_8b;
USART_InitStruct.USART_StopBits = USART_StopBits_1;
USART_InitStruct.USART_Parity = USART_Parity_No;
USART_InitStruct.USART_Mode = USART_Mode_Rx | USART_Mode_Tx;
USART_InitStruct.USART_HardwareFlowControl = USART_HardwareFlowControl_None;
USART_Init(DEBUG_USARTx, &USART_InitStruct);
// 使能串口
USART_Cmd(DEBUG_USARTx, ENABLE);
}
int fputc(int ch, FILE *f)
{
USART_SendData(DEBUG_USARTx, (uint8_t)ch);
while (USART_GetFlagStatus(DEBUG_USARTx, USART_FLAG_TXE) == RESET);
return ch;
}
// Memory -> P(USART->DR)
void USARTx_DMA_Config(void)
{
DMA_InitTypeDef DMA_InitStruct;
// 开时钟,我经常会忘记这一步(DMA挂载在AHB总线)
RCC_AHBPeriphClockCmd(USART_TX_DMA_CLK, ENABLE);
// 配置初始化结构体
DMA_InitStruct.DMA_PeripheralBaseAddr = (uint32_t)USART_DR_ADDRESS;
DMA_InitStruct.DMA_MemoryBaseAddr = (uint32_t)SendBuff;
/* DMA_DIR_PeripheralSRC:外设为源,DMA_DIR_PeripheralDST:外设为目的地 */
DMA_InitStruct.DMA_DIR = DMA_DIR_PeripheralDST;
DMA_InitStruct.DMA_BufferSize = SENDBUFF_SIZE;
DMA_InitStruct.DMA_PeripheralInc = DMA_PeripheralInc_Disable;
DMA_InitStruct.DMA_MemoryInc = DMA_MemoryInc_Enable;
DMA_InitStruct.DMA_PeripheralDataSize = DMA_PeripheralDataSize_Byte;
DMA_InitStruct.DMA_MemoryDataSize = DMA_MemoryDataSize_Byte;
DMA_InitStruct.DMA_Mode = DMA_Mode_Normal;
DMA_InitStruct.DMA_Priority = DMA_Priority_Medium;
DMA_InitStruct.DMA_M2M = DMA_M2M_Disable;
DMA_Init(DMA1_Channel4, &DMA_InitStruct);
DMA_Cmd(DMA1_Channel4, ENABLE);
}
bsp_dma.h头文件
#ifndef __BSP_DMA_H
#define __BSP_DMA_H
#include "stm32f10x.h"
// 串口1 USART1
#define DEBUG_USARTx USART1
#define DEBUG_USART_BAUDRATE 115200
#define DEBUG_USART_CLK RCC_APB2Periph_USART1
#define DEBUG_USART_APBxClkCmd RCC_APB2PeriphClockCmd
// USART GPIO引脚宏定义
#define DEBUG_UASRT_GPIO_CLK RCC_APB2Periph_GPIOA
#define DEBUG_UASRT_GPIO_APBxClkCmd RCC_APB2PeriphClockCmd
#define DEBUG_UASRT_TX_GPIO_PORT GPIOA
#define DEBUG_UASRT_TX_GPIO_PIN GPIO_Pin_9
#define DEBUG_UASRT_RX_GPIO_PORT GPIOA
#define DEBUG_UASRT_RX_GPIO_PIN GPIO_Pin_10
#define USART_TX_DMA_CLK RCC_AHBPeriph_DMA1
// 外设寄存器地址
#define USART_DR_ADDRESS (USART1_BASE + 0x04)
// 一次发送的数据量
#define SENDBUFF_SIZE 5000
// 串口对应的DMA请求通道
#define USART_TX_DMA_CHANNEL DMA1_Channel4
extern uint8_t SendBuff[SENDBUFF_SIZE];
void USART_Config(void);
void USARTx_DMA_Config(void);
#endif /* __BSP_DMA_H */
然后再主函数中进行调用。注意,这里有一点与Memory to Memory不同,MtM一旦使能就会进行传输,不需要触发。而这里需要USART发送一个DMA请求,然后DMA才会开始进行数据传输,请求函数为:
/**
* @brief Enables or disables the USART抯 DMA interface.
* @param USARTx: Select the USART or the UART peripheral.
* This parameter can be one of the following values:
* USART1, USART2, USART3, UART4 or UART5.
* @param USART_DMAReq: specifies the DMA request.
* This parameter can be any combination of the following values:
* @arg USART_DMAReq_Tx: USART DMA transmit request
* @arg USART_DMAReq_Rx: USART DMA receive request
* @param NewState: new state of the DMA Request sources.
* This parameter can be: ENABLE or DISABLE.
* @retval None
*/
void USART_DMACmd(USART_TypeDef* USARTx, uint16_t USART_DMAReq, FunctionalState NewState)
{
if (NewState != DISABLE)
{
/* Enable the DMA transfer for selected requests by setting the DMAT and/or
DMAR bits in the USART CR3 register */
USARTx->CR3 |= USART_DMAReq;
}
else
{
/* Disable the DMA transfer for selected requests by clearing the DMAT and/or
DMAR bits in the USART CR3 register */
USARTx->CR3 &= (uint16_t)~USART_DMAReq;
}
}
可以看到,USART-DMA请求函数,实际上配置的是UASRT_CR3寄存器,两个参数如下,分别配置的是CR3的第7位和第6位,对应发送请求使能和接受请求使能。
#define USART_DMAReq_Tx ((uint16_t)0x0080)
#define USART_DMAReq_Rx ((uint16_t)0x0040)
我们在完成初始化配置后,调用这个USART_DMACmd函数,DMA就会立刻开始传输。
在主函数中进行测试
main.c
#include "stm32f10x.h"
#include "bsp_led.h"
#include "bsp_dma.h"
void delay(uint32_t count);
int main(void)
{
uint16_t i = 0;
LED_GPIO_Config();
USART_Config();
USARTx_DMA_Config();
for (; i < SENDBUFF_SIZE; i++)
{
SendBuff[i] = 'P';
}
USART_DMACmd(DEBUG_USARTx, USART_DMAReq_Tx, ENABLE);
while (1)
{
LED_R_TOGGLE;
delay(0XFFFFF);
}
}
void delay(uint32_t count)
{
for (; count != 0; count--);
}