iptables-服务篇

install iptables

yum install iptables-services

开放端口及配置生效

# 保存配置
service iptables save
# 开放端口
iptables -I INPUT -p tcp --dport 80 -j ACCEPT

默认 iptables-config

# 6.8
# vi /etc/sysconfig/iptables
# Generated by iptables-save v1.4.7 on Wed Jun 12 23:51:42 2019
*mangle
:PREROUTING ACCEPT [20893:30265333]
:INPUT ACCEPT [20893:30265333]
:FORWARD ACCEPT [0:0]
:OUTPUT ACCEPT [14778:1031828]
:POSTROUTING ACCEPT [14778:1031828]
COMMIT
# Completed on Wed Jun 12 23:51:42 2019
# Generated by iptables-save v1.4.7 on Wed Jun 12 23:51:42 2019
*raw
:PREROUTING ACCEPT [20893:30265333]
:OUTPUT ACCEPT [14778:1031828]
COMMIT
# Completed on Wed Jun 12 23:51:42 2019
# Generated by iptables-save v1.4.7 on Wed Jun 12 23:51:42 2019
*filter
:INPUT ACCEPT [20893:30265333]
:FORWARD ACCEPT [0:0]
:OUTPUT ACCEPT [14778:1031828]
COMMIT
# Completed on Wed Jun 12 23:51:42 2019

# 6.9
# Firewall configuration written by system-config-firewall
# Manual customization of this file is not recommended.
*filter
:INPUT ACCEPT [0:0]
:FORWARD ACCEPT [0:0]
:OUTPUT ACCEPT [0:0]
-A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT
-A INPUT -p icmp -j ACCEPT
-A INPUT -i lo -j ACCEPT
-A INPUT -m state --state NEW -m tcp -p tcp --dport 22 -j ACCEPT
-A INPUT -j REJECT --reject-with icmp-host-prohibited
-A FORWARD -j REJECT --reject-with icmp-host-prohibited
COMMIT

iptables help

[root@localhost ~]# iptables
iptables v1.4.7

Usage: iptables -[ACD] chain rule-specification [options]
       iptables -I chain [rulenum] rule-specification [options]
       iptables -R chain rulenum rule-specification [options]
       iptables -D chain rulenum [options]
       iptables -[LS] [chain [rulenum]] [options]
       iptables -[FZ] [chain] [options]
       iptables -[NX] chain
       iptables -E old-chain-name new-chain-name
       iptables -P chain target [options]
       iptables -h (print this help information)

Commands:
Either long or short options are allowed.
  --append  -A chain		Append to chain
  --check   -C chain		Check for the existence of a rule
  --delete  -D chain		Delete matching rule from chain
  --delete  -D chain rulenum
				Delete rule rulenum (1 = first) from chain
  --insert  -I chain [rulenum]
				Insert in chain as rulenum (default 1=first)
  --replace -R chain rulenum
				Replace rule rulenum (1 = first) in chain
  --list    -L [chain [rulenum]]
				List the rules in a chain or all chains
  --list-rules -S [chain [rulenum]]
				Print the rules in a chain or all chains
  --flush   -F [chain]		Delete all rules in  chain or all chains
  --zero    -Z [chain [rulenum]]
				Zero counters in chain or all chains
  --new     -N chain		Create a new user-defined chain
  --delete-chain
            -X [chain]		Delete a user-defined chain
  --policy  -P chain target
				Change policy on chain to target
  --rename-chain
            -E old-chain new-chain
				Change chain name, (moving any references)
Options:
[!] --proto	-p proto	protocol: by number or name, eg. `tcp'
[!] --source	-s address[/mask][...]
				source specification
[!] --destination -d address[/mask][...]
				destination specification
[!] --in-interface -i input name[+]
				network interface name ([+] for wildcard)
 --jump	-j target
				target for rule (may load target extension)
  --goto      -g chain
                              jump to chain with no return
  --match	-m match
				extended match (may load extension)
  --numeric	-n		numeric output of addresses and ports
[!] --out-interface -o output name[+]
				network interface name ([+] for wildcard)
  --table	-t table	table to manipulate (default: `filter')
  --verbose	-v		verbose mode
  --line-numbers		print line numbers when listing
  --exact	-x		expand numbers (display exact values)
[!] --fragment	-f		match second or further fragments only
  --modprobe=<command>		try to insert modules using this command
  --set-counters PKTS BYTES	set the counter during insert/append
[!] --version	-V		print package version.

start nginx

#!/bin/sh
#
# nginx - this script starts and stops the nginx daemon
#
# chkconfig:   - 85 15
# description:  Nginx is an HTTP(S) server, HTTP(S) reverse \
#               proxy and IMAP/POP3 proxy server
# processname: nginx
# config:      /etc/nginx/nginx.conf
# config:      /etc/sysconfig/nginx
# pidfile:     /var/run/nginx.pid

# Source function library.
. /etc/rc.d/init.d/functions

# Source networking configuration.
. /etc/sysconfig/network

# Check that networking is up.
[ "$NETWORKING" = "no" ] && exit 0

nginx="/usr/sbin/nginx"
prog=$(basename $nginx)

sysconfig="/etc/sysconfig/$prog"
lockfile="/var/lock/subsys/nginx"
pidfile="/var/run/${prog}.pid"

NGINX_CONF_FILE="/etc/nginx/nginx.conf"

[ -f $sysconfig ] && . $sysconfig


start() {
    [ -x $nginx ] || exit 5
    [ -f $NGINX_CONF_FILE ] || exit 6
    echo -n $"Starting $prog: "
    daemon $nginx -c $NGINX_CONF_FILE
    retval=$?
    echo
    [ $retval -eq 0 ] && touch $lockfile
    return $retval
}

stop() {
    echo -n $"Stopping $prog: "
    killproc -p $pidfile $prog
    retval=$?
    echo
    [ $retval -eq 0 ] && rm -f $lockfile
    return $retval
}

restart() {
    configtest_q || return 6
    stop
    start
}

reload() {
    configtest_q || return 6
    echo -n $"Reloading $prog: "
    killproc -p $pidfile $prog -HUP
    echo
}

configtest() {
    $nginx -t -c $NGINX_CONF_FILE
}

configtest_q() {
    $nginx -t -q -c $NGINX_CONF_FILE
}

rh_status() {
    status $prog
}

rh_status_q() {
    rh_status >/dev/null 2>&1
}

# Upgrade the binary with no downtime.
upgrade() {
    local oldbin_pidfile="${pidfile}.oldbin"

    configtest_q || return 6
    echo -n $"Upgrading $prog: "
    killproc -p $pidfile $prog -USR2
    retval=$?
    sleep 1
    if [[ -f ${oldbin_pidfile} && -f ${pidfile} ]];  then
        killproc -p $oldbin_pidfile $prog -QUIT
        success $"$prog online upgrade"
        echo 
        return 0
    else
        failure $"$prog online upgrade"
        echo
        return 1
    fi
}

# Tell nginx to reopen logs
reopen_logs() {
    configtest_q || return 6
    echo -n $"Reopening $prog logs: "
    killproc -p $pidfile $prog -USR1
    retval=$?
    echo
    return $retval
}

case "$1" in
    start)
        rh_status_q && exit 0
        $1
        ;;
    stop)
        rh_status_q || exit 0
        $1
        ;;
    restart|configtest|reopen_logs)
        $1
        ;;
    force-reload|upgrade) 
        rh_status_q || exit 7
        upgrade
        ;;
    reload)
        rh_status_q || exit 7
        $1
        ;;
    status|status_q)
        rh_$1
        ;;
    condrestart|try-restart)
        rh_status_q || exit 7
        restart
	    ;;
    *)
        echo $"Usage: $0 {start|stop|reload|configtest|status|force-reload|upgrade|restart|reopen_logs}"
        exit 2
esac