高通平台启动log概述(PBL log、sbl1 log、kernel log)
高通平台启动log概述(PBL log、sbl1 log、kernel log)
在嵌入式linux的调试过程中log有着至关重要的地位，等同于医生的CT报告。能够熟悉启动各个阶段的log，如PBL阶段，sbl1阶段，kernel阶段，android阶段，对于分析定位问题有着重要的作用。本文以高通msm8937平台android启动的串口log为例简要介绍一下log相关的技巧和对log的概要介绍。
关于各个启动阶段的分析，可以参考：linux驱动由浅入深系列：PBL-SBL1-(bootloader)LK-Android启动过程详解之一（高通MSM8953启动实例）
user版本不同于userdebug版本，可能会关闭串口log，在调试user版时就需要开启。
开启的方法如下
1，cmdline
需要保证cmdline中有androidboot.console=ttyHSL0
2，defconfig
需要在kernel的配置中添加
CONFIG_SERIAL_MSM_HSL=y
CONFIG_SERIAL_MSM_HSL_CONSOLE=y
串口console在开机后可能会降低打印级别，可以通过如下命令显示所有log
echo "8 6 1 7" > /proc/sys/kernel/printk
关闭所有log显示
echo "0 6 1 7" > /proc/sys/kernel/printk
启动log概述
下面是msm8937平台上完整的开机串口log，红色部分是PBL log，绿色部分是sbl1 log，紫色为lk部分log，蓝色部分是kernel log，深蓝色部分kernel启动12s左右内核启动完毕，可以看到之后启了第一个用户进程init，由init进程启动android
Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.3-00221
S - IMAGE_VARIANT_STRING=FAASANAZA
S - OEM_IMAGE_VERSION_STRING=ubuntu
S - Boot Config, 0x000000e1
B - 246 - PBL, Start
B - 2946 - bootable_media_detect_entry, Start
B - 69427 - bootable_media_detect_success, Start
B - 69432 - elf_loader_entry, Start
B - 71073 - auth_hash_seg_entry, Start
B - 71322 - auth_hash_seg_exit, Start
B - 99643 - elf_segs_hash_verify_entry, Start
B - 200021 - PBL, End
B - 209901 - SBL1, Start
B - 263947 - pm_device_init, Start
B - 267302 - PON REASON:PM0:0x200000021 PM1:0x200000020
D - 26443 - pm_device_init, Delta
B - 292281 - boot_flash_init, Start
D - 0 - boot_flash_init, Delta
B - 294599 - boot_config_data_table_init, Start
D - 4636 - boot_config_data_table_init, Delta - (0 Bytes)
B - 304603 - CDT version:3,Platform ID:8,Major ID:1,Minor ID:0,Subtype:0
B - 311466 - sbl1_ddr_set_params, Start
B - 315736 - cpr_init, Start
D - 3751 - cpr_init, Delta
B - 321775 - Pre_DDR_clock_init, Start
D - 305 - Pre_DDR_clock_init, Delta
D - 0 - sbl1_ddr_set_params, Delta
B - 334005 - do ddr sanity test, Start
D - 305 - do ddr sanity test, Delta
B - 339678 - pm_driver_init, Start
B - 346175 - Manually set to USB500 mode
B - 346907 - raw vbat: 4485, gain: -21
B - 350719 - vbat: 4249
B - 353068 - Battery good, bootup
D - 13420 - pm_driver_init, Delta
B - 359808 - vsense_init, Start
D - 0 - vsense_init, Delta
B - 366488 - DDR Training restore, Start
D - 305 - DDR Training restore, Delta
B - 381616 - clock_init, Start
D - 183 - clock_init, Delta
B - 381860 - Image Load, Start
D - 87230 - QSEE Image Loaded, Delta - (1541808 Bytes)
B - 469120 - Image Load, Start
D - 335 - SEC Image Loaded, Delta - (2048 Bytes)
B - 506391 - sbl1_efs_handle_cookies, Start
D - 671 - sbl1_efs_handle_cookies, Delta
B - 508282 - Image Load, Start
D - 12383 - DEVCFG Image Loaded, Delta - (55764 Bytes)
B - 521184 - Image Load, Start
D - 20099 - RPM Image Loaded, Delta - (180504 Bytes)
B - 541314 - Image Load, Start
D - 52277 - APPSBL Image Loaded, Delta - (579748 Bytes)
B - 593621 - QSEE Execution, Start
D - 122 - QSEE Execution, Delta
B - 599386 - USB D+ check, Start
D - 122 - USB D+ check, Delta
B - 605760 - SBL1, End
D - 398116 - SBL1, Delta
S - Flash Throughput, 28000 KB/s (2363264 Bytes, 83714 us)
S - DDR Frequency, 806 MHz
S - Core 0 Frequency, 800 MHz
Android Bootloader - UART_DM Initialized!!!
[0] welcome to lk
[10] platform_init()
[10] target_init()
[30] SDHC Running in HS400 mode
[40] Done initialization of the card
[40] pm8x41_get_is_cold_boot: cold boot
[40] Qseecom Init Done in Appsbl
[50] secure app region addr=0x84300000 size=0x2000000[50] TZ App region notif returned with status:0 addr:84300000 size:33554432
[60] TZ App log region register returned with status:0 addr:8f6b2000 size:4096
[60] Qseecom TZ Init Done in Appsbl
[80] Loading cmnlib done
[80] qseecom_start_app: Loading app keymaster for the first time'
[100] <8>keymaster64: KEYMASTER Init
[100] Waiting for the RPM to populate smd channel table
[110] Not able to search the panel:
[110] DIJING_HX83102B_HD720_VIDEO_PANEL ----
[120] panel_operating_mode=0x0
[180] ERROR: splash Partition invalid
[210] Config MIPI_VIDEO_PANEL.
LCD ID = 0x1201d5
[370] swb.mdss_dsi_panel_auto_detect_ashley read signature lcdid = 0
[370] mdss_dsi_panel_auto_detect_ashley:auto detect failed, so use LCD default configuration.
[520] Turn on MIPI_VIDEO_PANEL.
[540] Video lane tested successfully
[540] pm8x41_get_is_cold_boot: cold boot
[540] Recovery command: 32 bootonce-bootloader
[550] Unable to locate /bootselect partition
[550] boot_verifier: Device is in ORANGE boot state.
[560] Device is unlocked! Skipping verification...
[560] Loading (boot) image (13461504): start
[610] Loading (boot) image (13461504): done
[610] use_signed_kernel=1, is_unlocked=1, is_tampered=0.
[620] Your device has been unlocked and can't be trusted.
Wait for 5 seconds before proceeding
[5620] LK SEC APP Handle: 0x1
[5630] <8>keymaster64: "cmd_id=SET_ROT begin"
[5630] <8>keymaster64: Error: qsee_cfg_getpropval in get_enable_set_bandwidth failed for enable_set_bandwidth, ret_size = 0
[5640] <8>keymaster64: "rot.data_length: 32"
[5640] <8>keymaster64: "cmd_id=SET_ROT done with ret: 0 time taken: 0"
[5650] LK SEC APP Handle: 0x1
[5650] <8>keymaster64: "cmd_id=GET_VERSION begin"
[5660] Authentication Key not yet programmed
[5670] <8>keymaster64: qsee_stor_device_init error ret: -14
[5680] <8>keymaster64: "secboot device : 0"
[5680] <8>keymaster64: "cmd_id=GET_VERSION done with ret: 0 time taken: 18"
[5690] <8>keymaster64: "cmd_id=SET_BOOT_STATE begin"
[5690] <8>keymaster64: "is_unlocked: 1"
[5700] <8>keymaster64: "color: 1"
[5700] <8>keymaster64: "system_version: 80000"
[5700] <8>keymaster64: "system_security_level 201708"
[5710] <8>keymaster64: "cmd_id=SET_BOOT_STATE done with ret: 0 time taken: 0"
[5710] Uncpmpressed kernel in use
[5720] Kernel image not patched..Unable to locate dt offset
[5780] Best match DTB tags 294/00000008/0x00000000/0/10019/10011/0/0/a0a2f8a0/3b0bd
[5780] Using pmic info 0x10019/0x10011/0x0/0x0 for device 0x10019/0x20011/0x0/0x0
[5790] pm8x41_get_is_cold_boot: cold boot
[5790] target_pause_for_battery_charge : pon_reason is:0x21 cold_boot:1 usb_sts:0
[5800] display kernel cmdline: mdss_mdp.panel=1:dsi:0:qcom,mdss_dsi_dijing_hx83102b_hd720_video:1:none:cfg:single_dsi
[5810] cmdline: console=ttyHSL0,115200,n8 androidboot.console=ttyHSL0 androidboot.hardware=qcom user_debug=30 msm_rtb.filter=0x237 ehci-hcd.park=3 androidboot.bootdevice=7824900.sdhci lpm_levels.sleep_disabled=1 earlycon=msm_hsl_uart,0x78B0000 buildvariant=userd[5830] Updating device tree: start
[5850] Updating device tree: done
[5850] Turn off MIPI_VIDEO_PANEL.
[5850] Continuous splash enabled, keeping panel alive.
[5860] <8>keymaster64: "cmd_id=MILESTONE_CALL begin"
[5860] <8>keymaster64: "cmd_id=MILESTONE_CALL done with ret: 0 time taken: 0"
[5870] Qseecom De-Init Done in Appsbl
[5870] Channel alloc freed
[5880] booting linux @ 0x40008000, ramdisk @ 0x43600000 (1691976), tags/device tree @ 0x43400000
[ 0.000000] Booting Linux on physical CPU 0x100
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 3.18.66-g13d1896-dirty (lilu@ubuntu) (gcc version 4.8 (GCC) ) #6 SMP PREEMPT Mon Oct 30 11:06:27 CST 2017
[ 0.000000] CPU: ARMv7 Processor [410fd034] revision 4 (ARMv7), cr=10c0383d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine model: Qualcomm Technologies, Inc. MSM8937-PMI8950 MTP
[ 0.000000] Early serial console at I/O port 0x0 (options '')
[ 0.000000] bootconsole [uart0] enabled
[ 0.000000] Reserved memory: reserved region for node 'other_ext_region@0': base 0x84300000, size 37 MiB
[ 0.000000] Reserved memory: reserved region for node 'modem_region@0': base 0x86800000, size 80 MiB
[ 0.000000] Reserved memory: reserved region for node 'adsp_fw_region@0': base 0x8b800000, size 17 MiB
[ 0.000000] Reserved memory: reserved region for node 'wcnss_fw_region@0': base 0x8c900000, size 7 MiB
[ 0.000000] Reserved memory: reserved region for node 'splash_region@83000000': base 0x90000000, size 20 MiB
[ 0.000000] Removed memory: created DMA memory pool at 0x84300000, size 37 MiB
[ 0.000000] Reserved memory: initialized node other_ext_region@0, compatible id removed-dma-pool
[ 0.000000] Removed memory: created DMA memory pool at 0x86800000, size 80 MiB
[ 0.000000] Reserved memory: initialized node modem_region@0, compatible id removed-dma-pool
[ 0.000000] Removed memory: created DMA memory pool at 0x8b800000, size 17 MiB
[ 0.000000] Reserved memory: initialized node adsp_fw_region@0, compatible id removed-dma-pool
[ 0.000000] Removed memory: created DMA memory pool at 0x8c900000, size 7 MiB
[ 0.000000] Reserved memory: initialized node wcnss_fw_region@0, compatible id removed-dma-pool
[ 0.000000] Reserved memory: allocated memory for 'venus_region@0' node: base 0x8f800000, size 8 MiB
[ 0.000000] Reserved memory: created CMA memory pool at 0x8f800000, size 8 MiB
[ 0.000000] Reserved memory: initialized node venus_region@0, compatible id shared-dma-pool
[ 0.000000] Reserved memory: allocated memory for 'secure_region@0' node: base 0xf8c00000, size 112 MiB
[ 0.000000] Reserved memory: created CMA memory pool at 0xf8c00000, size 112 MiB
[ 0.000000] Reserved memory: initialized node secure_region@0, compatible id shared-dma-pool
[ 0.000000] Reserved memory: allocated memory for 'qseecom_region@0' node: base 0xf7c00000, size 16 MiB
[ 0.000000] Reserved memory: created CMA memory pool at 0xf7c00000, size 16 MiB
[ 0.000000] Reserved memory: initialized node qseecom_region@0, compatible id shared-dma-pool
[ 0.000000] Reserved memory: allocated memory for 'adsp_region@0' node: base 0xf7800000, size 4 MiB
[ 0.000000] Reserved memory: created CMA memory pool at 0xf7800000, size 4 MiB
[ 0.000000] Reserved memory: initialized node adsp_region@0, compatible id shared-dma-pool
[ 0.000000] cma: Reserved 16 MiB at 0xf6800000
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.0 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] PERCPU: max_distance=0xb000 too large for vmalloc space 0x0
[ 0.000000] PERCPU: Embedded 11 pages/cpu @ead65000 s15872 r8192 d20992 u45056
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 766255
[ 0.000000] Kernel command line: sched_enable_hmp=1 console=ttyHSL0,115200,n8 androidboot.console=ttyHSL0 androidboot.hardware=qcom user_debug=30 msm_rtb.filter=0x237 ehci-hcd.park=3 androidboot.bootdevice=7824900.sdhci lpm_levels.sleep_disabled=1 earlycon=msm_hsl_uart,0x78B0000 buildvariant=userdebug androidboot.emmc=true androidboot.verifiedbootstate=orange androidboot.veritymode=enforcing androidboot.keymaster=1 androidboot.serialno=1aead0af androidboot.baseband=msm mdss_mdp.panel=1:dsi:0:qcom,mdss_dsi_dijing_hx83102b_hd720_video:1:none:cfg:single_dsi
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 2718092K/3083260K available (13312K kernel code, 1770K rwdata, 6140K rodata, 859K init, 2102K bss, 365168K reserved, 2042876K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xef800000 - 0xff000000 ( 248 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xef800000 ( 760 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0e00000 (14304 kB)
[ 0.000000] .init : 0xc1500000 - 0xc15d6e00 ( 860 kB)
[ 0.000000] .data : 0xc1600000 - 0xc17baadc (1771 kB)
[ 0.000000] .bss : 0xc17baba0 - 0xc19c84cc (2103 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[ 0.000000] HMP scheduling enabled.
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000]
[ 0.000000] **********************************************************
[ 0.000000] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE **
[ 0.000000] ** **
[ 0.000000] ** trace_printk() being used. Allocating extra memory. **
[ 0.000000] ** **
[ 0.000000] ** This means that this is a DEBUG kernel and it is **
[ 0.000000] ** unsafe for produciton use. **
[ 0.000000] ** **
[ 0.000000] ** If you see this message and you are not debugging **
[ 0.000000] ** the kernel, report this immediately to your vendor! **
[ 0.000000] ** **
[ 0.000000] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE **
[ 0.000000] **********************************************************
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] mpm_init_irq_domain(): Cannot find irq controller for qcom,gpio-parent
[ 0.000000] MPM 1 irq mapping errored -517
[ 0.000000] Offload RCU callbacks from all CPUs
[ 0.000000] Offload RCU callbacks from CPUs: 0-7.
[ 0.000000] Architected cp15 and mmio timer(s) running at 19.20MHz (virt/virt).
[ 0.000006] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 3579139424256ns
[ 0.007982] Switching to timer-based delay loop, resolution 52ns
[ 0.013975] Switched to clocksource arch_sys_counter
[ 0.031718] kmemleak: Kernel memory leak detector disabled
[ 0.036203] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=192000)
[ 0.046493] pid_max: default: 32768 minimum: 301
[ 0.052229] Security Framework initialized
[ 0.055331] SELinux: Initializing.
[ 0.059552] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.065401] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.078383] Initializing cgroup subsys freezer
[ 0.081927] Initializing cgroup subsys debug
[ 0.086379] CPU: Testing write buffer coherency: ok
[ 0.093297] Setting up static identity map for 0x40d9b310 - 0x40d9b368
[ 0.099308] NOHZ: local_softirq_pending 02
[ 0.157427] Core Debug Lock unlocked
[ 0.160654] MSM Memory Dump base table set up
[ 0.164409] MSM Memory Dump apps data table set up
[ 0.169146] Configuring XPU violations to be fatal errors
[ 0.177940] cpu_clock_a53_init_little: A53 Power clocks configured
[ 0.207249] CPU1: Booted secondary processor
[ 0.233518] CPU2: Booted secondary processor
[ 0.252898] CPU3: Booted secondary processor
[ 0.272527] CPU4: Booted secondary processor
[ 0.292070] CPU5: Booted secondary processor
[ 0.311702] CPU6: Booted secondary processor
[ 0.331314] CPU7: Booted secondary processor
[ 0.331574] Brought up 8 CPUs
[ 0.363284] SMP: Total of 8 processors activated (307.20 BogoMIPS).
[ 0.369546] CPU: All CPU(s) started in SVC mode.
[ 0.393498] VFP support v0.3: implementor 41 architecture 3 part 40 variant 3 rev 4
[ 0.547289] pinctrl core: initialized pinctrl subsystem
[ 0.556629] regulator-dummy: no parameters
[ 1.702270] NET: Registered protocol family 16
[ 1.734331] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 1.749111] msm_pm_tz_boot_init: set warmboot address failed
[ 1.753757] scm_call failed: func id 0x2000101, ret: -1, syscall returns: 0x0, 0x0, 0x0
[ 1.774074] cpuidle: using governor ladder
[ 1.794067] cpuidle: using governor menu
[ 1.814065] cpuidle: using governor qcom
[ 2.056060] msm_watchdog b017000.qcom,wdt: wdog absent resource not present
[ 2.063644] msm_watchdog b017000.qcom,wdt: MSM Watchdog Initialized
[ 2.105451] platform soc:qcom,adsprpc-mem: assigned reserved memory node adsp_region@0
[ 2.121714] irq: no irq domain found for /soc/pinctrl@1000000 !
[ 2.130351] spmi_pmic_arb 200f000.qcom,spmi: PMIC Arb Version-2 0x20010000
[ 2.190435] platform 4080000.qcom,mss: assigned reserved memory node modem_region@0
[ 2.200694] platform c200000.qcom,lpass: assigned reserved memory node adsp_fw_region@0
[ 2.209599] platform a21b000.qcom,pronto: assigned reserved memory node wcnss_fw_region@0
[ 2.218356] platform 1de0000.qcom,venus: assigned reserved memory node venus_region@0
[ 2.233283] mem_acc_corner: 0 <--> 0 mV at 0 mV
[ 2.334424] irq: no irq domain found for /soc/pinctrl@1000000 !
[ 2.343127] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[ 2.350124] hw-breakpoint: maximum watchpoint size is 8 bytes.
[ 2.371555] __of_mpm_init(): MPM driver mapping exists
[ 2.378981] msm_rpm_glink_dt_parse: qcom,rpm-glink compatible not matches
[ 2.384774] msm_rpm_dev_probe: APSS-RPM communication over SMD
[ 2.390544] smd_open() before smd_init()
[ 2.398187] msm_mpm_dev_probe(): Cannot get clk resource for XO: -517
[ 2.424426] smd_channel_probe_now: allocation table not initialized
[ 2.431088] smd_channel_probe_now: allocation table not initialized
[ 2.437766] smd_channel_probe_now: allocation table not initialized
[ 2.467137] msm-jtag-fuse a601c.jtagfuse: JTag Fuse initialized
[ 2.479527] pm8937_s5: 1050 <--> 1350 mV at 1225 mV normal idle
[ 2.486714] spm_regulator_probe: name=pm8937_s5, range=LV, voltage=1225000 uV, mode=AUTO, step rate=1200 uV/us
[ 2.498132] cpr_efuse_init: apc_corner: efuse_addr = 0x000a4000 (len=0x1000)
[ 2.504246] cpr_read_fuse_revision: apc_corner: fuse revision = 2
[ 2.510222] cpr_parse_speed_bin_fuse: apc_corner: [row: 37]: 0x30185021bb873125, speed_bits = 0
[ 2.519126] cpr_adjust_init_voltages: apc_corner: adjusted initial voltage[1]: 1105000 -> 1115000 uV
[ 2.528036] cpr_adjust_init_voltages: apc_corner: adjusted initial voltage[2]: 1165000 -> 1180000 uV
[ 2.537149] cpr_adjust_init_voltages: apc_corner: adjusted initial voltage[3]: 1250000 -> 1270000 uV
[ 2.546322] cpr_pvs_init: apc_corner: pvs voltage: [1115000 1180000 1270000] uV
[ 2.553533] cpr_pvs_init: apc_corner: ceiling voltage: [1155000 1225000 1350000] uV
[ 2.561191] cpr_pvs_init: apc_corner: floor voltage: [1050000 1050000 1090000] uV
[ 2.569590] cpr_init_cpr_parameters: apc_corner: up threshold = 2, down threshold = 4
[ 2.576491] cpr_init_cpr_parameters: apc_corner: CPR is enabled by default.
[ 2.583493] cpr_init_cpr_efuse: apc_corner: [row:67] = 0x248dae53d19918ea
[ 2.590199] cpr_init_cpr_efuse: apc_corner: Corner[1]: ro_sel = 2, target quot = 875
[ 2.597907] cpr_init_cpr_efuse: apc_corner: Corner[2]: ro_sel = 2, target quot = 977
[ 2.605643] cpr_init_cpr_efuse: apc_corner: Corner[3]: ro_sel = 2, target quot = 1123
[ 2.613456] cpr_adjust_target_quots: apc_corner: Corner[2]: adjusted target quot = 937
[ 2.621350] cpr_adjust_target_quots: apc_corner: Corner[3]: adjusted target quot = 1143
[ 2.629797] cpr_get_corner_quot_adjustment: apc_corner: fuse corner 2 quotient adjustment scaling factor: 0.462
[ 2.639402] cpr_get_corner_quot_adjustment: apc_corner: fuse corner 3 quotient adjustment scaling factor: 0.671
[ 2.649475] cpr_get_corner_quot_adjustment: apc_corner: adjusted quotient[1] = 875
[ 2.657020] cpr_get_corner_quot_adjustment: apc_corner: adjusted quotient[2] = 937
[ 2.664571] cpr_get_corner_quot_adjustment: apc_corner: adjusted quotient[3] = 1015
[ 2.672193] cpr_get_corner_quot_adjustment: apc_corner: adjusted quotient[4] = 1041
[ 2.679850] cpr_get_corner_quot_adjustment: apc_corner: adjusted quotient[5] = 1105
[ 2.687488] cpr_get_corner_quot_adjustment: apc_corner: adjusted quotient[6] = 1143
[ 2.695127] cpr_get_corner_quot_adjustment: apc_corner: adjusted quotient[7] = 1143
[ 2.703608] cpr_config: apc_corner: Timer count: 0x17700 (for 5000 us)
[ 2.712595] apc_corner: 0 <--> 0 mV
[ 2.728742] msm_thermal:vdd_restriction_reg_init Defer regulator vdd-dig probe
[ 2.734948] msm_thermal:probe_vdd_rstr Err regulator init. err:-517. KTM continues.
[ 2.742569] msm-thermal soc:qcom,msm-thermal: probe_vdd_rstr:Failed reading node=/soc/qcom,msm-thermal, key=qcom,max-freq-level. err=-517. KTM continues
[ 2.756236] msm_thermal:msm_thermal_dev_probe Failed reading node=/soc/qcom,msm-thermal, key=qcom,online-hotplug-core. err:-517
[ 2.776657] sps:sps is ready.
[ 2.784085] cpu-clock-8939 b011050.qcom,cpu-clock-8939: No PVS version available. Defaulting to 0!
[ 2.792005] cpu-clock-8939 b011050.qcom,cpu-clock-8939: Speed bin: 0 PVS Version: 0
[ 2.808519] msm_rpm_glink_dt_parse: qcom,rpm-glink compatible not matches
[ 2.814349] msm_rpm_dev_probe: APSS-RPM communication over SMD
[ 2.826852] pm8937_s1: 1000 <--> 1225 mV at 1000 mV normal idle
[ 2.840419] pm8937_s2_level: 0 <--> 0 mV at 0 mV normal idle
[ 2.851335] pm8937_s2_floor_level: 0 <--> 0 mV at 0 mV normal idle
[ 2.862801] pm8937_s2_level_ao: 0 <--> 0 mV at 0 mV normal idle
[ 2.876797] pm8937_s3: 1300 mV normal idle
[ 2.888786] pm8937_s4: 2050 mV normal idle
[ 2.900712] pm8937_l2: 1200 mV normal idle
[ 2.912562] pm8937_l3_level_ao: 0 <--> 0 mV at 0 mV normal idle
[ 2.923919] pm8937_l3_level_so: 0 <--> 0 mV at 0 mV normal idle
[ 2.937677] pm8937_l5: 1800 mV normal idle
[ 2.949653] pm8937_l6: 1800 mV normal idle
[ 2.961526] pm8937_l7: 1800 mV normal idle
[ 2.970993] pm8937_l7_ao: 1800 mV normal idle
[ 2.983226] pm8937_l8: 2850 <--> 2900 mV at 2900 mV normal idle
[ 2.997042] pm8937_l9: 3000 <--> 3300 mV at 3000 mV normal idle
[ 3.011019] pm8937_l10: 2800 <--> 3000 mV at 2800 mV normal idle
[ 3.025064] pm8937_l11: 2950 mV normal idle
[ 3.036998] pm8937_l12: 1800 <--> 2950 mV at 1800 mV normal idle
[ 3.050689] pm8937_l13: 3075 mV normal idle
[ 3.062729] pm8937_l14: 1800 <--> 3300 mV at 1800 mV normal idle
[ 3.076456] pm8937_l15: 1800 <--> 3300 mV at 1800 mV normal idle
[ 3.090448] pm8937_l16: 1800 mV normal idle
[ 3.102371] pm8937_l17: 2800 <--> 2900 mV at 2800 mV normal idle
[ 3.116286] pm8937_l19: 1225 <--> 1350 mV at 1225 mV normal idle
[ 3.130065] pm8937_l22: 2800 mV normal idle
[ 3.142094] pm8937_l23: 1200 mV normal idle
[ 3.148110] msm_mpm_dev_probe(): Cannot get clk resource for XO: -517
[ 3.155386] msm_thermal:sensor_mgr_init_threshold threshold id already initialized
[ 3.163105] cpu cpu0: dev_pm_opp_get_opp_count: device OPP not found (-19)
[ 3.168962] msm_thermal:get_cpu_freq_plan_len Error reading CPU0 freq table len. error:-19
[ 3.177207] cpu cpu4: dev_pm_opp_get_opp_count: device OPP not found (-19)
[ 3.184059] msm_thermal:get_cpu_freq_plan_len Error reading CPU4 freq table len. error:-19
[ 3.192288] msm_thermal:vdd_restriction_reg_init Defer vdd rstr freq init.
[ 3.204314] cpu cpu0: dev_pm_opp_get_opp_count: device OPP not found (-19)
[ 3.204457] cpu-clock-8939 b011050.qcom,cpu-clock-8939: No PVS version available. Defaulting to 0!
[ 3.204465] cpu-clock-8939 b011050.qcom,cpu-clock-8939: Speed bin: 0 PVS Version: 0
[ 3.211010] qcom,gcc-8952 1800000.qcom,gcc: GPU speed bin: 0
[ 3.232396] msm_thermal:get_cpu_freq_plan_len Error reading CPU0 freq table len. error:-19
[ 3.240641] cpu cpu4: dev_pm_opp_get_opp_count: device OPP not found (-19)
[ 3.247490] msm_thermal:get_cpu_freq_plan_len Error reading CPU4 freq table len. error:-19
[ 3.255739] cpu cpu0: dev_pm_opp_get_opp_count: device OPP not found (-19)
[ 3.262577] msm_thermal:get_cpu_freq_plan_len Error reading CPU0 freq table len. error:-19
[ 3.270844] cpu cpu4: dev_pm_opp_get_opp_count: device OPP not found (-19)
[ 3.277696] msm_thermal:get_cpu_freq_plan_len Error reading CPU4 freq table len. error:-19
[ 3.394312] qcom,gcc-spm-8952 b111200.qcom,spm: Registered GCC SPM clocks
[ 3.400079] qcom,gcc-8952 1800000.qcom,gcc: Registered GCC clocks
[ 3.410076] cpu-clock-8939 b011050.qcom,cpu-clock-8939: No PVS version available. Defaulting to 0!
[ 3.418024] cpu-clock-8939 b011050.qcom,cpu-clock-8939: Speed bin: 0 PVS Version: 0
[ 3.436978] populate_opp_table: clock-cpu-8939: OPP tables populated (cpu 7 and 3)
[ 3.443331] print_opp_table: clock_cpu: a53_c0: OPP voltage for 768000000: 1115000
[ 3.451081] print_opp_table: clock_cpu: a53_c0: OPP voltage for 1094400000: 1270000
[ 3.458712] print_opp_table: clock_cpu: a53_c1: OPP voltage for 960000000: 1115000
[ 3.466264] print_opp_table: clock_cpu: a53_c1: OPP voltage for 1401000000: 1270000
[ 4.060624] qcom,qpnp-pin qpnp-pin-15: qpnp_pin_probe: no device nodes specified in topology
[ 4.068172] qcom,qpnp-pin: probe of qpnp-pin-15 failed with error -22
[ 4.074904] qcom,qpnp-pin qpnp-pin-16: qpnp_pin_probe: no device nodes specified in topology
[ 4.082975] qcom,qpnp-pin: probe of qpnp-pin-16 failed with error -22
[ 4.091887] msm_cpuss_dump soc:cpuss_dump: Couldn't get memory for dumping
[ 4.097759] msm_cpuss_dump soc:cpuss_dump: Couldn't get memory for dumping
[ 4.120038] KPI: Bootloader start count = 22986
[ 4.123529] KPI: Bootloader end count = 216025
[ 4.128021] KPI: Bootloader display count = 40196
[ 4.132643] KPI: Bootloader load kernel count = 1497
[ 4.137618] KPI: Kernel MPM timestamp = 480515
[ 4.142018] KPI: Kernel MPM Clock frequency = 32768
[ 4.146960] socinfo_print: v0.10, id=294, ver=1.0, raw_id=79, raw_ver=0, hw_plat=8, hw_plat_ver=65536
[ 4.146960] accessory_chip=0, hw_plat_subtype=0, pmic_model=65561, pmic_die_revision=65536 foundry_id=1 serial_number=3146199333
[ 4.169649] qpnp_pin_of_gpio_xlate: no such PMIC gpio 7 in device topology
[ 4.177652] eldo2_pm8937: no parameters
[ 4.182274] qpnp_pin_of_gpio_xlate: no such PMIC gpio 8 in device topology
[ 4.190143] adv_vreg: no parameters
[ 4.203681] SCSI subsystem initialized
[ 4.211880] usbcore: registered new interface driver usbfs
[ 4.217411] usbcore: registered new interface driver hub
[ 4.222675] usbcore: registered new device driver usb
[ 4.231476] i2c-msm-v2 78b6000.i2c: probing driver i2c-msm-v2
[ 4.236689] AXI: msm_bus_scale_register_client(): msm_bus_scale_register_client: Bus driver not ready.
[ 4.245328] i2c-msm-v2 78b6000.i2c: msm_bus_scale_register_client(mstr-id:86):0 (not a problem)
[ 4.259686] kworker/u16:0 (96) used greatest stack depth: 6264 bytes left
[ 4.266407] i2c-msm-v2 78b7000.i2c: probing driver i2c-msm-v2
[ 4.271595] AXI: msm_bus_scale_register_client(): msm_bus_scale_register_client: Bus driver not ready.
[ 4.280311] i2c-msm-v2 78b7000.i2c: msm_bus_scale_register_client(mstr-id:86):0 (not a problem)
[ 4.303738] i2c-msm-v2 7af5000.i2c: probing driver i2c-msm-v2
[ 4.308900] AXI: msm_bus_scale_register_client(): msm_bus_scale_register_client: Bus driver not ready.
[ 4.317589] i2c-msm-v2 7af5000.i2c: msm_bus_scale_register_client(mstr-id:84):0 (not a problem)
[ 4.334210] media: Linux media interface: v0.10
[ 4.338520] Linux video capture interface: v2.00
[ 4.343305] EDAC MC: Ver: 3.0.0
[ 4.356214] cpufreq: driver msm up and running
[ 4.362625] platform soc:qcom,ion:qcom,ion-heap@8: assigned reserved memory node secure_region@0
[ 4.371440] platform soc:qcom,ion:qcom,ion-heap@27: assigned reserved memory node qseecom_region@0
[ 4.382005] ION heap system created
[ 4.384935] ION heap mm created at 0xf8c00000 with size 7000000
[ 4.390421] ION heap qsecom created at 0xf7c00000 with size 1000000
[ 4.397374] msm_bus_fabric_init_driver
[ 4.404751] msm_bus_device 580000.ad-hoc-bus: Coresight support absent for bus: 2048
[ 4.492890] qcom,qpnp-power-on qpnp-power-on-4: PMIC@SID0 Power-on reason: Triggered from Hard Reset and 'cold' boot
[ 4.502403] qcom,qpnp-power-on qpnp-power-on-4: PMIC@SID0: Power-off reason: Triggered from PS_HOLD (PS_HOLD/MSM controlled shutdown)
[ 4.516392] input: qpnp_pon as /devices/virtual/input/input0
[ 4.524400] pon_spare_reg: no parameters
[ 4.528138] qcom,qpnp-power-on qpnp-power-on-13: No PON config. specified
[ 4.534548] qcom,qpnp-power-on qpnp-power-on-13: PMIC@SID2 Power-on reason: Triggered from PON1 (secondary PMIC) and 'cold' boot
[ 4.545625] qcom,qpnp-power-on qpnp-power-on-13: PMIC@SID2: Power-off reason: Triggered from PS_HOLD (PS_HOLD/MSM controlled shutdown)
[ 4.558570] PMIC@SID0: PM8937 v1.0 options: 0, 2, 0, 0
[ 4.563100] PMIC@SID2: PMI8950 v2.0 options: 0, 0, 0, 0
[ 4.571462] gdsc_venus: no parameters
[ 4.576700] gdsc_mdss: no parameters
[ 4.581849] gdsc_jpeg: no parameters
[ 4.587207] gdsc_vfe: no parameters
[ 4.592440] gdsc_vfe1: no parameters
[ 4.597568] gdsc_cpp: no parameters
[ 4.602639] gdsc_oxili_gx: no parameters
[ 4.607982] gdsc_venus_core0: fast normal
[ 4.613570] gdsc_oxili_cx: no parameters
[ 4.619219] mdss_pll_probe: MDSS pll label = MDSS DSI 0 PLL
[ 4.623802] mdss_pll_probe: mdss_pll_probe: label=MDSS DSI 0 PLL PLL SSC enabled
[ 4.631212] mdss_pll_util_parse_dt_supply: : error reading ulp load. rc=-22
[ 4.638089] mdss_pll_util_parse_dt_supply: : error reading ulp load. rc=-22
[ 4.648446] dsi_pll_clock_register_lpm: Registered DSI PLL:0 clocks successfully
[ 4.655059] mdss_pll_probe: MDSS pll label = MDSS DSI 1 PLL
[ 4.660370] mdss_pll_probe: mdss_pll_probe: label=MDSS DSI 1 PLL PLL SSC enabled
[ 4.667804] mdss_pll_util_parse_dt_supply: : error reading ulp load. rc=-22
[ 4.674694] mdss_pll_util_parse_dt_supply: : error reading ulp load. rc=-22
[ 4.685635] dsi_pll_clock_register_lpm: Registered DSI PLL:1 clocks successfully
[ 4.693603] msm_iommu 1e00000.qcom,iommu: device apps_iommu (model: 500) mapped at efe80000, with 21 ctx banks
[ 4.729351] msm_iommu_ctx 1e20000.qcom,iommu-ctx: context q6 using bank 0
[ 4.736222] msm_iommu_ctx 1e21000.qcom,iommu-ctx: context adsp_sec_pixel using bank 1
[ 4.744087] msm_iommu_ctx 1e22000.qcom,iommu-ctx: context mdp_1 using bank 2
[ 4.751156] msm_iommu_ctx 1e23000.qcom,iommu-ctx: context venus_fw using bank 3
[ 4.758522] msm_iommu_ctx 1e24000.qcom,iommu-ctx: context venus_sec_non_pixel using bank 4
[ 4.766832] msm_iommu_ctx 1e25000.qcom,iommu-ctx: context venus_sec_bitstream using bank 5
[ 4.775160] msm_iommu_ctx 1e26000.qcom,iommu-ctx: context venus_sec_pixel using bank 6
[ 4.783102] msm_iommu_ctx 1e28000.qcom,iommu-ctx: context pronto_pil using bank 8
[ 4.791073] msm_iommu_ctx 1e29000.qcom,iommu-ctx: context mss_nav using bank 9
[ 4.798420] msm_iommu_ctx 1e2a000.qcom,iommu-ctx: context periph_rpm using bank 10
[ 4.806083] msm_iommu_ctx 1e2b000.qcom,iommu-ctx: context lpass using bank 11
[ 4.813257] msm_iommu_ctx 1e2f000.qcom,iommu-ctx: context adsp_io using bank 15
[ 4.820598] msm_iommu_ctx 1e30000.qcom,iommu-ctx: context adsp_opendsp using bank 16
[ 4.828399] msm_iommu_ctx 1e31000.qcom,iommu-ctx: context adsp_shared using bank 17
[ 4.836110] msm_iommu_ctx 1e32000.qcom,iommu-ctx: context cpp using bank 18
[ 4.843134] msm_iommu_ctx 1e33000.qcom,iommu-ctx: context jpeg_enc0 using bank 19
[ 4.850767] msm_iommu_ctx 1e34000.qcom,iommu-ctx: context vfe using bank 20
[ 4.857790] msm_iommu_ctx 1e35000.qcom,iommu-ctx: context mdp_0 using bank 21
[ 4.865009] msm_iommu_ctx 1e36000.qcom,iommu-ctx: context venus_ns using bank 22
[ 4.872451] msm_iommu_ctx 1e38000.qcom,iommu-ctx: context mss_mcdma using bank 24
[ 4.880035] msm_iommu_ctx 1e37000.qcom,iommu-ctx: context access_control using bank 23
[ 4.889921] /soc/qcom,cam_smmu/msm_cam_smmu_cb1: could not get #iommu-cells for /soc/qcom,iommu@1e00000
[ 4.898319] /soc/qcom,cam_smmu/msm_cam_smmu_cb3: could not get #iommu-cells for /soc/qcom,iommu@1e00000
[ 4.907686] /soc/qcom,cam_smmu/msm_cam_smmu_cb4: could not get #iommu-cells for /soc/qcom,iommu@1e00000
[ 4.923317] Advanced Linux Sound Architecture Driver Initialized.
[ 4.935623] Bluetooth: eaa9fec8
[ 4.937785] NET: Registered protocol family 31
[ 4.942142] Bluetooth: eaa9fec8
[ 4.945156] Bluetooth: eaa9fec0Bluetooth: eaa9fea8
[ 4.950088] Bluetooth: eaa9feb8[ 4.954830] cfg80211: Calling CRDA to update world regulatory domain
[ 4.960248] cfg80211: World regulatory domain updated:
[ 4.965278] cfg80211: DFS Master region: unset
[ 4.969599] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 4.979336] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 4.987320] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 4.995306] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 5.003280] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 5.011279] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 5.019272] cfg80211: (5490000 KHz - 5710000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 5.027250] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 5.035240] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ 5.046703] ibb_reg: 4600 <--> 6000 mV at 6000 mV
[ 5.053207] lab_reg: 4600 <--> 6000 mV at 6000 mV
[ 5.059569] Switched to clocksource arch_sys_counter
[ 5.428973] NET: Registered protocol family 2
[ 5.436094] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[ 5.442468] TCP bind hash table entries: 8192 (order: 5, 163840 bytes)
[ 5.448729] TCP: Hash tables configured (established 8192 bind 8192)
[ 5.455226] TCP: reno registered
[ 5.458201] UDP hash table entries: 512 (order: 2, 24576 bytes)
[ 5.464141] UDP-Lite hash table entries: 512 (order: 2, 24576 bytes)
[ 5.471976] NET: Registered protocol family 1
[ 5.483158] gcc-mdss-8952 soc:qcom,gcc-mdss@1800000: Registered GCC MDSS clocks.
[ 5.492606] Trying to unpack rootfs image as initramfs...
[ 5.573908] Freeing initrd memory: 1656K
[ 5.579166] hw perfevents: enabled with ARMv8 Cortex-A53 PMU driver, 7 counters available
[ 5.606337] futex hash table entries: 2048 (order: 5, 131072 bytes)
[ 5.611617] Initialise system trusted keyring
[ 5.616227] audit: initializing netlink subsys (disabled)
[ 5.621605] audit: type=2000 audit(5.599:1): initialized
[ 5.638614] vmscan: error setting kswapd cpu affinity mask
[ 5.782079] VFS: Disk quotas dquot_6.5.2
[ 5.786653] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 5.830366] fuse init (API version 7.23)
[ 5.847734] Key type asymmetric registered
[ 5.850814] Asymmetric key parser 'x509' registered
[ 5.856537] bounce: pool size: 64 pages
[ 5.861287] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
[ 5.867687] io scheduler noop registered
[ 5.871569] io scheduler deadline registered
[ 5.879057] io scheduler cfq registered (default)
[ 5.911946] msm_dss_get_res_byname: 'vbif_nrt_phys' resource not found
[ 5.917457] mdss_mdp_probe+0x1f0/0x13e8->msm_dss_ioremap_byname: 'vbif_nrt_phys' msm_dss_get_res_byname failed
[ 5.928923] mdss_mdp_irq_clk_register: unable to get clk: lut_clk
[ 5.935961] No change in context(0==0), skip
[ 5.940352] mdss_mdp_pipe_addr_setup: type:0 ftchid:-1 xinid:0 num:0 rect:0 ndx:0x1 prio:0
[ 5.947637] mdss_mdp_pipe_addr_setup: type:1 ftchid:-1 xinid:1 num:3 rect:0 ndx:0x8 prio:1
[ 5.955839] mdss_mdp_pipe_addr_setup: type:1 ftchid:-1 xinid:5 num:4 rect:0 ndx:0x10 prio:2
[ 5.964210] mdss_mdp_pipe_addr_setup: type:2 ftchid:-1 xinid:2 num:6 rect:0 ndx:0x40 prio:3
[ 5.972526] mdss_mdp_pipe_addr_setup: type:3 ftchid:-1 xinid:7 num:10 rect:0 ndx:0x400 prio:0
[ 5.981023] mdss_mdp_parse_dt_handler: Error from prop qcom,mdss-pipe-sw-reset-off : u32 array read
[ 5.990279] mdss_mdp_parse_dt_handler: Error from prop qcom,mdss-ib-factor-overlap : u32 array read
[ 6.001020] xlog_status: enable:1, panic:1, dump:2
[ 6.008421] mdss_mdp_probe: mdss version = 0x100e0000, bootloader display is on, num 1, intf_sel=0x00000100
[ 6.023551] mdss_smmu_util_parse_dt_clock: clocks are not defined
[ 6.028795] mdss_smmu_probe: iommu v2 domain[0] mapping and clk register successful!
[ 6.036604] mdss_smmu_util_parse_dt_clock: clocks are not defined
[ 6.042499] mdss_smmu_probe: iommu v2 domain[2] mapping and clk register successful!
[ 6.052585] mdss_dsi_get_dt_vreg_data: error reading ulp load. rc=-22
[ 6.058033] mdss_dsi_get_dt_vreg_data: error reading ulp load. rc=-22
[ 6.064480] mdss_dsi_get_dt_vreg_data: error reading ulp load. rc=-22
[ 6.075193] mdss_dsi_ctrl_probe: DSI Ctrl name = MDSS DSI CTRL->0
[ 6.081856] mdss_dsi_find_panel_of_node: cmdline:0:qcom,mdss_dsi_dijing_hx83102b_hd720_video:1:none:cfg:single_dsi panel_name:qcom,mdss_dsi_dijing_hx83102b_hd720_video
[ 6.095854] mdss_dsi_panel_init: Panel Name = dijing hd720 hx83102b video mode dsi panel
[ 6.104066] mdss_dsi_panel_timing_from_dt: found new timing "qcom,mdss_dsi_dijing_hx83102b_hd720_video" (eaa9f7e0)
[ 6.114235] mdss_dsi_parse_dcs_cmds: failed, key=qcom,mdss-dsi-post-panel-on-command
[ 6.121895] mdss_dsi_parse_dcs_cmds: failed, key=qcom,mdss-dsi-timing-switch-command
[ 6.129635] mdss_dsi_panel_get_dsc_cfg_np: cannot find dsc config node:
[ 6.136392] mdss_dsi_parse_dcs_cmds: failed, key=qcom,mdss-dsi-idle-on-command
[ 6.143423] mdss_dsi_parse_dcs_cmds: failed, key=qcom,mdss-dsi-idle-off-command
[ 6.150754] mdss_dsi_parse_panel_features: ulps feature disabled
[ 6.156717] mdss_dsi_parse_panel_features: ulps during suspend feature disabled
[ 6.163821] mdss_dsi_parse_dms_config: dynamic switch feature enabled: 0
[ 6.170850] mdss_dsi_parse_dcs_cmds: failed, key=qcom,mdss-dsi-lp-mode-on
[ 6.177469] mdss_dsi_parse_dcs_cmds: failed, key=qcom,mdss-dsi-lp-mode-off
[ 6.184434] mdss_dsi_get_dt_vreg_data: error reading ulp load. rc=-22
[ 6.190735] mdss_dsi_get_dt_vreg_data: error reading ulp load. rc=-22
[ 6.197176] mdss_dsi_get_dt_vreg_data: error reading ulp load. rc=-22
[ 6.203582] mdss_dsi_get_dt_vreg_data: error reading ulp load. rc=-22
[ 6.211545] mdss_dsi_parse_ctrl_params:4024 Unable to read qcom,display-id, data=00000000,len=45
[ 6.219338] mdss_dsi_parse_gpio_params: bklt_en gpio not specified
[ 6.225618] mdss_dsi_retrieve_ctrl_resources: phy_regulator_base=efb10b80 phy_regulator_size=30
[ 6.234152] mdss_dsi_retrieve_ctrl_resources: ctrl_base=efb0c000 ctrl_size=300 phy_base=efb0e400 phy_size=280
[ 6.244453] dsi_panel_device_register: Continuous splash enabled
[ 6.250331] mdss_register_panel: adding framebuffer device 1a94000.qcom,mdss_dsi_ctrl0
[ 6.281092] mdss_dsi_ctrl_probe: Dsi Ctrl->0 initialized, DSI rev:0x10040002, PHY rev:0x1
[ 6.288656] mdss_dsi_status_init: DSI status check interval:3000
[ 6.296289] mdss_register_panel: adding framebuffer device soc:qcom,mdss_wb_panel
[ 6.304835] mdss_fb_probe: fb0: split_mode:0 left:0 right:0
[ 6.316285] mdss_fb_register: FrameBuffer[0] 720x1440 registered successfully!
[ 6.325879] mdss_fb_probe: fb1: split_mode:0 left:0 right:0
[ 6.331939] mdss_fb_register: FrameBuffer[1] 640x640 registered successfully!
[ 6.339428] mdss_mdp_splash_parse_dt: splash mem child node is not present
[ 6.347687] msm-dcc b3000.dcc: DCC XPU is not specified
[ 6.366468] IPC_RTR: msm_ipc_router_smd_driver_register Already driver registered IPCRTR
[ 6.373815] IPC_RTR: msm_ipc_router_smd_driver_register Already driver registered IPCRTR
[ 6.410659] In memshare_probe, Memshare probe success
[ 6.420254] msm_rpm_log_probe: OK
[ 6.435111] subsys-pil-tz 1de0000.qcom,venus: for venus segments only will be dumped.
[ 6.457837] msm_serial_hs module loaded
[ 6.461680] msm_serial_hsl_probe: detected port #0 (ttyHSL0)
[ 6.466444] AXI: get_pdata(): Error: Client name not found
[ 6.471766] AXI: msm_bus_cl_get_pdata(): client has to provide missing entry for successful registration
[ 6.481247] msm_serial_hsl_probe: Bus scaling is disabled
[ 6.487348] 78b0000.serial: ttyHSL0 at MMIO 0x78b0000 (irq = 40, base_baud = 460800?瞨⑹獖聮陙msm_hsl_console_setup: console setup on port #0
[ 6.499755] console [ttyHSL0] enabled
[ 6.499755] console [ttyHSL0] enabled
[ 6.507026] bootconsole [uart0] disabled
[ 6.507026] bootconsole [uart0] disabled
[ 6.517026] msm_serial_hsl_init: driver initialized
[ 6.681118] brd: module loaded
[ 6.718396] loop: module loaded
[ 6.725631] zram: Created 1 device(s) ...
[ 6.729125] lkdtm: No crash points registered, enable through debugfs
[ 6.737137] QSEECOM: qseecom_probe: qseecom.qsee_version = 0x1000000
[ 6.742611] QSEECOM: qseecom_retrieve_ce_data: Device does not support PFE
[ 6.749155] QSEECOM: qseecom_probe: qseecom clocks handled by other subsystem
[ 6.756437] QSEECOM: qseecom_probe: qsee reentrancy support phase is not defined, setting to default 0
[ 6.766862] QSEECOM: qseecom_probe: qseecom.whitelist_support = 1
[ 6.792797] i2c-core: driver [tabla-i2c-core] using legacy suspend method
[ 6.798558] i2c-core: driver [tabla-i2c-core] using legacy resume method
[ 6.806371] i2c-core: driver [wcd9xxx-i2c-core] using legacy suspend method
[ 6.812286] i2c-core: driver [wcd9xxx-i2c-core] using legacy resume method
[ 6.820286] i2c-core: driver [tasha-i2c-core] using legacy suspend method
[ 6.826046] i2c-core: driver [tasha-i2c-core] using legacy resume method
[ 6.834839] QCE50: __qce_get_device_tree_data: BAM Apps EE is not defined, setting to default 1
[ 6.844903] qce 720000.qcedev: Qualcomm Crypto 5.3.3 device found @0x720000
[ 6.850824] qce 720000.qcedev: CE device = 0x0
[ 6.850824] IO base, CE = 0xf0940000
[ 6.850824] Consumer (IN) PIPE 2, Producer (OUT) PIPE 3
[ 6.850824] IO base BAM = 0x00000000
[ 6.850824] BAM IRQ 53
[ 6.850824] Engines Availability = 0x2010853
[ 6.876929] sps:BAM 0x00704000 is registered.
[ 6.881004] sps:BAM 0x00704000 (va:0xf0b00000) enabled: ver:0x27, number of pipes:8
[ 6.888956] QCE50: qce_sps_init: Qualcomm MSM CE-BAM at 0x0000000000704000 irq 53
[ 6.901011] QCE50: __qce_get_device_tree_data: BAM Apps EE is not defined, setting to default 1
[ 6.911826] qcrypto 720000.qcrypto: Qualcomm Crypto 5.3.3 device found @0x720000
[ 6.918209] qcrypto 720000.qcrypto: CE device = 0x0
[ 6.918209] IO base, CE = 0xf0b40000
[ 6.918209] Consumer (IN) PIPE 4, Producer (OUT) PIPE 5
[ 6.918209] IO base BAM = 0x00000000
[ 6.918209] BAM IRQ 53
[ 6.918209] Engines Availability = 0x2010853
[ 6.943724] QCE50: qce_sps_init: Qualcomm MSM CE-BAM at 0x0000000000704000 irq 53
[ 6.953374] qcrypto 720000.qcrypto: qcrypto-ecb-aes
[ 6.957599] qcrypto 720000.qcrypto: qcrypto-cbc-aes
[ 6.962430] qcrypto 720000.qcrypto: qcrypto-ctr-aes
[ 6.967277] qcrypto 720000.qcrypto: qcrypto-ecb-des
[ 6.972149] qcrypto 720000.qcrypto: qcrypto-cbc-des
[ 6.977067] qcrypto 720000.qcrypto: qcrypto-ecb-3des
[ 6.981959] qcrypto 720000.qcrypto: qcrypto-cbc-3des
[ 6.986896] qcrypto 720000.qcrypto: qcrypto-xts-aes
[ 6.991739] qcrypto 720000.qcrypto: qcrypto-sha1
[ 6.996466] qcrypto 720000.qcrypto: qcrypto-sha256
[ 7.001226] qcrypto 720000.qcrypto: qcrypto-aead-hmac-sha1-cbc-aes
[ 7.007306] qcrypto 720000.qcrypto: qcrypto-aead-hmac-sha1-cbc-des
[ 7.013445] qcrypto 720000.qcrypto: qcrypto-aead-hmac-sha1-cbc-3des
[ 7.019713] qcrypto 720000.qcrypto: qcrypto-aead-hmac-sha256-cbc-aes
[ 7.026053] qcrypto 720000.qcrypto: qcrypto-aead-hmac-sha256-cbc-des
[ 7.032368] qcrypto 720000.qcrypto: qcrypto-aead-hmac-sha256-cbc-3des
[ 7.038804] qcrypto 720000.qcrypto: qcrypto-hmac-sha1
[ 7.043820] qcrypto 720000.qcrypto: qcrypto-hmac-sha256
[ 7.049050] qcrypto 720000.qcrypto: qcrypto-aes-ccm
[ 7.053893] qcrypto 720000.qcrypto: qcrypto-rfc4309-aes-ccm
[ 7.061542] qcom_ice_get_device_tree_data: No vdd-hba-supply regulator, assuming not needed
[ 7.069608] ICE IRQ = 55
[ 7.077114] SCSI Media Changer driver v0.25
[ 7.087083] tun: Universal TUN/TAP device driver, 1.6
[ 7.091088] tun: (C) 1999-2004 Max Krasnyansky
[ 7.105166] PPP generic driver version 2.4.2
[ 7.109477] PPP BSD Compression module registered
[ 7.113161] PPP Deflate Compression module registered
[ 7.118278] PPP MPPE Compression module registered
[ 7.122993] NET: Registered protocol family 24
[ 7.131057] wcnss_wlan probed in built-in mode
[ 7.140660] usbcore: registered new interface driver asix
[ 7.145508] usbcore: registered new interface driver ax88179_178a
[ 7.151479] usbcore: registered new interface driver cdc_ether
[ 7.157361] usbcore: registered new interface driver net1080
[ 7.162949] usbcore: registered new interface driver cdc_subset
[ 7.168867] usbcore: registered new interface driver zaurus
[ 7.175085] usbcore: registered new interface driver cdc_ncm
[ 7.182136] msm_sharedmem: sharedmem_register_qmi: qmi init successful
[ 7.194379] scm_call failed: func id 0x2000c16, ret: -1, syscall returns: 0x0, 0x0, 0x0
[ 7.201357] hyp_assign_table: Failed to assign memory protection, ret = -5
[ 7.208257] msm_sharedmem: setup_shared_ram_perms: hyp_assign_phys failed IPA=0x0160xf6e00000 size=1572864 err=-5
[ 7.220074] msm_sharedmem: msm_sharedmem_probe: Device created for client 'rmtfs'
[ 7.228202] msm_otg 78db000.usb: msm_otg probe
[ 7.237527] msm_otg 78db000.usb: OTG regs = efe1e000
[ 7.259719] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 7.265297] ehci-msm: Qualcomm On-Chip EHCI Host Controller
[ 7.271655] Unable to get vbus_otg
[ 7.274168] msm_hsusb_host msm_hsusb_host: unable to register with transceiver
[ 7.282183] usbcore: registered new interface driver cdc_acm
[ 7.287010] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 7.295677] usbcore: registered new interface driver usb-storage
[ 7.301288] usbcore: registered new interface driver ums-alauda
[ 7.307205] usbcore: registered new interface driver ums-cypress
[ 7.313166] usbcore: registered new interface driver ums-datafab
[ 7.319177] usbcore: registered new interface driver ums-freecom
[ 7.325160] usbcore: registered new interface driver ums-isd200
[ 7.331036] usbcore: registered new interface driver ums-jumpshot
[ 7.337175] usbcore: registered new interface driver ums-karma
[ 7.342939] usbcore: registered new interface driver ums-onetouch
[ 7.349032] usbcore: registered new interface driver ums-sddr09
[ 7.354930] usbcore: registered new interface driver ums-sddr55
[ 7.360808] usbcore: registered new interface driver ums-usbat
[ 7.367292] usbcore: registered new interface driver usbserial
[ 7.372574] usbcore: registered new interface driver usb_ehset_test
[ 7.383090] gbridge_init: gbridge_init successs.
[ 7.393248] mousedev: PS/2 mouse device common for all mice
[ 7.399889] usbcore: registered new interface driver xpad
[ 7.404285] [FTS]fts_ts_init: Enter
[ 7.409915] [FTS]fts_ts_probe: Enter
[ 7.412459] [FTS]fts_parse_dt: Enter
[ 7.416053] [FTS]max_touch_number=10
[ 7.419562] [FTS]fts_parse_dt: Exit(900)
[ 7.423574] [FTS]fts_ctpm_get_upgrade_array: Enter
[ 7.428261] [FTS][Info]CHIP TYPE ID = 0x8006
[ 7.432496] [FTS]fts_ctpm_get_upgrade_array: Exit(166)
[ 7.437632] [FTS]fts_gpio_configure: Enter
[ 7.441754] [FTS]fts_gpio_configure: Exit(770)
[ 7.684611] i2c-msm-v2 78b7000.i2c: msm_bus_scale_register_client(mstr-id:86):0xe (ok)
[ 7.691664] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:1 tx:1) mode:FIFO slv_addr:0x38 MSTR_STS:0x0d1300c8 OPER:0x00000010
[ 7.707240] [FTS][Error][IIC]: i2c_transfer(write) error, ret=-107!!
[ 7.713528] [FTS][Error]FTS tp is not ready or does not exsit
[ 7.719397] fts_ts: probe of 3-0038 failed with error -107
[ 7.724986] [FTS]fts_ts_init: Exit(1357)
[ 7.728659] [NVT-ts] nvt_driver_init 1596: start
[ 7.733592] [NVT-ts] nvt_ts_probe 1118: start
[ 7.737624] [NVT-ts] nvt_parse_dt 830: novatek,irq-gpio=65
[ 7.754008] [NVT-ts] nvt_bootloader_reset 348: xlixiang---enter-nvt_bootloader_reset
[ 7.760811] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 7.776559] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 7.792269] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 7.807981] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 7.823692] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 7.839302] [NVT-ts] CTP_I2C_WRITE 310: error, ret=-107
[ 7.894110] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 7.908934] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 7.924648] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 7.940357] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 7.956073] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 7.971679] [NVT-ts] CTP_I2C_WRITE 310: error, ret=-107
[ 8.004108] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 8.018932] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 8.034643] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 8.050357] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 8.066068] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 8.081677] [NVT-ts] CTP_I2C_WRITE 310: error, ret=-107
[ 8.104108] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:3) mode:FIFO slv_addr:0x1 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 8.118846] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:3) mode:FIFO slv_addr:0x1 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 8.134473] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:3) mode:FIFO slv_addr:0x1 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 8.150094] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:3) mode:FIFO slv_addr:0x1 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 8.165722] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:3) mode:FIFO slv_addr:0x1 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 8.181244] [NVT-ts] CTP_I2C_WRITE 310: error, ret=-107
[ 8.186534] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:6 tx:1) mode:FIFO slv_addr:0x1 MSTR_STS:0x0d1300c8 OPER:0x00000010
[ 8.202178] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:6 tx:1) mode:FIFO slv_addr:0x1 MSTR_STS:0x0d1300c8 OPER:0x00000010
[ 8.217809] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:6 tx:1) mode:FIFO slv_addr:0x1 MSTR_STS:0x0d1300c8 OPER:0x00000010
[ 8.233430] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:6 tx:1) mode:FIFO slv_addr:0x1 MSTR_STS:0x0d1300c8 OPER:0x00000010
[ 8.249057] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:6 tx:1) mode:FIFO slv_addr:0x1 MSTR_STS:0x0d1300c8 OPER:0x00000010
[ 8.264578] [NVT-ts] CTP_I2C_READ 259: error, ret=-107
[ 8.269662] [NVT-ts] nvt_ts_check_chip_ver_trim 1066: buf[1]=0x00, buf[2]=0x00, buf[3]=0x00, buf[4]=0x00, buf[5]=0x00, buf[6]=0x00
[ 8.294006] [NVT-ts] nvt_bootloader_reset 348: xlixiang---enter-nvt_bootloader_reset
[ 8.300806] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 8.316556] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 8.332267] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 8.347979] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 8.363690] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 8.379300] [NVT-ts] CTP_I2C_WRITE 310: error, ret=-107
[ 8.434109] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 8.448933] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 8.464649] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 8.480357] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 8.496068] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 8.511679] [NVT-ts] CTP_I2C_WRITE 310: error, ret=-107
[ 8.544110] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 8.558934] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 8.574647] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 8.590358] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 8.606069] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 8.621679] [NVT-ts] CTP_I2C_WRITE 310: error, ret=-107
[ 8.644109] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:3) mode:FIFO slv_addr:0x1 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 8.658847] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:3) mode:FIFO slv_addr:0x1 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 8.674472] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:3) mode:FIFO slv_addr:0x1 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 8.690095] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:3) mode:FIFO slv_addr:0x1 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 8.705720] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:3) mode:FIFO slv_addr:0x1 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 8.721246] [NVT-ts] CTP_I2C_WRITE 310: error, ret=-107
[ 8.726534] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:6 tx:1) mode:FIFO slv_addr:0x1 MSTR_STS:0x0d1300c8 OPER:0x00000010
[ 8.742182] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:6 tx:1) mode:FIFO slv_addr:0x1 MSTR_STS:0x0d1300c8 OPER:0x00000010
[ 8.757804] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:6 tx:1) mode:FIFO slv_addr:0x1 MSTR_STS:0x0d1300c8 OPER:0x00000010
[ 8.773431] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:6 tx:1) mode:FIFO slv_addr:0x1 MSTR_STS:0x0d1300c8 OPER:0x00000010
[ 8.789055] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:6 tx:1) mode:FIFO slv_addr:0x1 MSTR_STS:0x0d1300c8 OPER:0x00000010
[ 8.804578] [NVT-ts] CTP_I2C_READ 259: error, ret=-107
[ 8.809661] [NVT-ts] nvt_ts_check_chip_ver_trim 1066: buf[1]=0x00, buf[2]=0x00, buf[3]=0x00, buf[4]=0x00, buf[5]=0x00, buf[6]=0x00
[ 8.834004] [NVT-ts] nvt_bootloader_reset 348: xlixiang---enter-nvt_bootloader_reset
[ 8.840804] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 8.856554] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 8.872267] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 8.887977] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 8.903689] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 8.919300] [NVT-ts] CTP_I2C_WRITE 310: error, ret=-107
[ 8.974108] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 8.988933] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 9.004645] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 9.020361] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 9.036067] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 9.051677] [NVT-ts] CTP_I2C_WRITE 310: error, ret=-107
[ 9.084110] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 9.098933] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 9.114646] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 9.130358] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 9.146070] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 9.161678] [NVT-ts] CTP_I2C_WRITE 310: error, ret=-107
[ 9.184109] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:3) mode:FIFO slv_addr:0x1 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 9.198845] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:3) mode:FIFO slv_addr:0x1 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 9.214472] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:3) mode:FIFO slv_addr:0x1 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 9.230096] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:3) mode:FIFO slv_addr:0x1 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 9.245722] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:3) mode:FIFO slv_addr:0x1 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 9.261243] [NVT-ts] CTP_I2C_WRITE 310: error, ret=-107
[ 9.266536] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:6 tx:1) mode:FIFO slv_addr:0x1 MSTR_STS:0x0d1300c8 OPER:0x00000010
[ 9.282181] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:6 tx:1) mode:FIFO slv_addr:0x1 MSTR_STS:0x0d1300c8 OPER:0x00000010
[ 9.297805] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:6 tx:1) mode:FIFO slv_addr:0x1 MSTR_STS:0x0d1300c8 OPER:0x00000010
[ 9.313432] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:6 tx:1) mode:FIFO slv_addr:0x1 MSTR_STS:0x0d1300c8 OPER:0x00000010
[ 9.329056] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:6 tx:1) mode:FIFO slv_addr:0x1 MSTR_STS:0x0d1300c8 OPER:0x00000010
[ 9.344577] [NVT-ts] CTP_I2C_READ 259: error, ret=-107
[ 9.349661] [NVT-ts] nvt_ts_check_chip_ver_trim 1066: buf[1]=0x00, buf[2]=0x00, buf[3]=0x00, buf[4]=0x00, buf[5]=0x00, buf[6]=0x00
[ 9.374005] [NVT-ts] nvt_bootloader_reset 348: xlixiang---enter-nvt_bootloader_reset
[ 9.380805] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 9.396552] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 9.412268] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 9.427978] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 9.443689] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 9.459299] [NVT-ts] CTP_I2C_WRITE 310: error, ret=-107
[ 9.514111] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 9.528934] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 9.544648] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 9.560359] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 9.576069] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 9.591680] [NVT-ts] CTP_I2C_WRITE 310: error, ret=-107
[ 9.624110] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 9.638934] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 9.654648] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 9.670357] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 9.686070] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 9.701678] [NVT-ts] CTP_I2C_WRITE 310: error, ret=-107
[ 9.724109] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:3) mode:FIFO slv_addr:0x1 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 9.738846] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:3) mode:FIFO slv_addr:0x1 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 9.754472] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:3) mode:FIFO slv_addr:0x1 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 9.770096] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:3) mode:FIFO slv_addr:0x1 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 9.785720] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:3) mode:FIFO slv_addr:0x1 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 9.801242] [NVT-ts] CTP_I2C_WRITE 310: error, ret=-107
[ 9.806534] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:6 tx:1) mode:FIFO slv_addr:0x1 MSTR_STS:0x0d1300c8 OPER:0x00000010
[ 9.822179] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:6 tx:1) mode:FIFO slv_addr:0x1 MSTR_STS:0x0d1300c8 OPER:0x00000010
[ 9.837804] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:6 tx:1) mode:FIFO slv_addr:0x1 MSTR_STS:0x0d1300c8 OPER:0x00000010
[ 9.853431] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:6 tx:1) mode:FIFO slv_addr:0x1 MSTR_STS:0x0d1300c8 OPER:0x00000010
[ 9.869056] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:6 tx:1) mode:FIFO slv_addr:0x1 MSTR_STS:0x0d1300c8 OPER:0x00000010
[ 9.884577] [NVT-ts] CTP_I2C_READ 259: error, ret=-107
[ 9.889660] [NVT-ts] nvt_ts_check_chip_ver_trim 1066: buf[1]=0x00, buf[2]=0x00, buf[3]=0x00, buf[4]=0x00, buf[5]=0x00, buf[6]=0x00
[ 9.914003] [NVT-ts] nvt_bootloader_reset 348: xlixiang---enter-nvt_bootloader_reset
[ 9.920805] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 9.936555] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 9.952264] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 9.967976] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 9.983688] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 9.999297] [NVT-ts] CTP_I2C_WRITE 310: error, ret=-107
[ 10.054118] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 10.068941] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x0d1343c8 OPER:0x00000090
[ 10.084651] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x091343c8 OPER:0x00000090
[ 10.100362] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x091343c8 OPER:0x00000090
[ 10.116073] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x091343c8 OPER:0x00000090
[ 10.131687] [NVT-ts] CTP_I2C_WRITE 310: error, ret=-107
[ 10.164109] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 10.178928] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x091343c8 OPER:0x00000090
[ 10.194642] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 10.210353] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x0d1343c8 OPER:0x00000090
[ 10.226064] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x62 MSTR_STS:0x091343c8 OPER:0x00000090
[ 10.241676] [NVT-ts] CTP_I2C_WRITE 310: error, ret=-107
[ 10.264107] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:3) mode:FIFO slv_addr:0x1 MSTR_STS:0x0d1343c8 OPER:0x00000090
[ 10.278838] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:3) mode:FIFO slv_addr:0x1 MSTR_STS:0x091343c8 OPER:0x00000090
[ 10.294866] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:3) mode:FIFO slv_addr:0x1 MSTR_STS:0x0d1300c8 OPER:0x00000090
[ 10.310091] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:3) mode:FIFO slv_addr:0x1 MSTR_STS:0x091343c8 OPER:0x00000090
[ 10.325717] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:3) mode:FIFO slv_addr:0x1 MSTR_STS:0x0d1343c8 OPER:0x00000090
[ 10.341241] [NVT-ts] CTP_I2C_WRITE 310: error, ret=-107
[ 10.346528] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:6 tx:1) mode:FIFO slv_addr:0x1 MSTR_STS:0x091343c8 OPER:0x00000010
[ 10.362175] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:6 tx:1) mode:FIFO slv_addr:0x1 MSTR_STS:0x091343c8 OPER:0x00000010
[ 10.377801] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:6 tx:1) mode:FIFO slv_addr:0x1 MSTR_STS:0x0d1300c8 OPER:0x00000010
[ 10.393425] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:6 tx:1) mode:FIFO slv_addr:0x1 MSTR_STS:0x091343c8 OPER:0x00000010
[ 10.409050] i2c-msm-v2 78b7000.i2c: NACK: slave not responding, ensure its powered: msgs(n:2 cur:0 tx) bc(rx:6 tx:1) mode:FIFO slv_addr:0x1 MSTR_STS:0x0d1300c8 OPER:0x00000010
[ 10.424575] [NVT-ts] CTP_I2C_READ 259: error, ret=-107
[ 10.429659] [NVT-ts] nvt_ts_check_chip_ver_trim 1066: buf[1]=0x00, buf[2]=0x00, buf[3]=0x00, buf[4]=0x00, buf[5]=0x00, buf[6]=0x00
[ 10.454005] [NVT-ts] nvt_ts_probe 1152: chip is not identified
[ 10.458887] NVT-ts: probe of 3-0062 failed with error -22
[ 10.464412] nvt_driver_init: finished
[ 10.467843] [HXTP] Himax common touch panel driver init
[ 10.473069] [HXTP] himax_common_init_async:Enter
[ 10.475841] SX9310sx9310_probe()
[ 10.476602] i2c-msm-v2 78b6000.i2c: msm_bus_scale_register_client(mstr-id:86):0xf (ok)
[ 10.476828] SX9310sx9310 read_register for 0 time Addr: 0x42 Return: 0x1
[ 10.476830] SX9310sx9310 detect success!
[ 10.476879] SX9310read dtsi 0x13:0x05 set reg
[ 10.476881] SX9310read dtsi 0x18:0x79 set reg
[ 10.476883] SX9310read dtsi 0x19:0x79 set reg
[ 10.476913] SX9310 Initialized Main Memory: 0xe74c1700
[ 10.476930] SX9310 Initialized Device Specific Memory: 0xe75a1800
[ 10.478799] input: SX9310 Cap Touch top as /devices/virtual/input/input2
[ 10.481607] input: SX9310 Cap Touch bottom as /devices/virtual/input/input3
[ 10.487068] SX9310cap_vdd regulator is on
[ 10.487825] SX9310cap_svdd regulator is on
[ 10.488211] SX9310sx93XX_irq
[ 10.488443] SX9310read_register Addr: 0x0 Return: 0x80
[ 10.488446] SX9310Worker - Refresh Status 128
[ 10.488448] SX9310Looping Counter 0
[ 10.488450] SX9310Looping Counter 1
[ 10.488452] SX9310Looping Counter 2
[ 10.488454] SX9310Looping Counter 3
[ 10.488455] SX9310Looping Counter 4
[ 10.488457] SX9310Looping Counter 5
[ 10.488459] SX9310Looping Counter 6
[ 10.488461] SX9310Looping Counter 7
[ 10.488665] SX9310registered with threaded irq (215)
[ 10.488816] SX9310write_register Addr: 0x7f Val: 0xde Return: 2
[ 10.488818] SX9310Software Reset. Waiting device back to continue.
[ 10.488888] irq 21, desc: e9b2da80, depth: 0, count: 0, unhandled: 0
[ 10.488898] ->handle_irq(): c03cd090, msm_gpio_irq_handler+0x0/0x158
[ 10.488905] ->irq_data.chip(): c1635778, gic_chip+0x0/0x74
[ 10.488907] ->action(): (null)
[ 10.488909] IRQ_NOPROBE set
[ 10.488910] IRQ_NOREQUEST set
[ 10.488911] IRQ_NOTHREAD set
[ 10.633646] [HXTP] DT-himax_parse_dt:panel-coords = 0, 720, 0, 1440
[ 10.639544] [HXTP] DT-himax_parse_dt:display-coords = (720, 1440)
[ 10.645726] [HXTP] DT:gpio_3v3_en value is not valid
[ 10.650718] [HXTP] DT:gpio_irq=65, gpio_rst=64, gpio_3v3_en=-2
[ 10.656636] [HXTP] DT:protocol_type=1
[ 10.660353] [HXTP] DT-No vk info in DT
[ 10.694953] [HXTP] himax_ic_package_check:Read driver IC ID = 83,10,2B
[ 10.700433] [HXTP] Himax IC package 83102_in
[ 10.709196] [HXTP] PANEL_VER : C
[ 10.711464] [HXTP] FW_VER : 302
[ 10.715602] [HXTP] TOUCH_VER : 3
[ 10.717975] [HXTP] DISPLAY_VER : 1
[ 10.722354] [HXTP] CID_VER : 801
[ 10.770728] [HXTP] himax_hw_check_CRC: tmp_data[3]=0, tmp_data[2]=0, tmp_data[1]=0, tmp_data[0]=0
[ 10.778744] [HXTP] himax_loadSensorConfig: initialization complete
[ 10.784904] [HXTP] himax_power_on_init:
[ 10.788710] [HXTP] himax_touch_information:HX_RX_NUM =32,HX_TX_NUM =18,HX_MAX_PT=5
[ 10.794403] SX9310Device back from the reset, continuing. NIRQ = 1
[ 10.794405] SX9310Going to Setup I2C Registers
[ 10.794408] SX9310Going to Write Reg: 0x3 Value: 0xf0
[ 10.796405] SX9310write_register Addr: 0x3 Val: 0xf0 Return: 2
[ 10.796407] SX9310Going to Write Reg: 0x4 Value: 0x0
[ 10.802553] SX9310write_register Addr: 0x4 Val: 0x0 Return: 2
[ 10.802555] SX9310Going to Write Reg: 0x11 Value: 0x2
[ 10.806995] SX9310write_register Addr: 0x11 Val: 0x2 Return: 2
[ 10.806997] SX9310Going to Write Reg: 0x12 Value: 0xb
[ 10.812014] SX9310write_register Addr: 0x12 Val: 0xb Return: 2
[ 10.812016] SX9310Going to Write Reg: 0x13 Value: 0x5
[ 10.817844] SX9310write_register Addr: 0x13 Val: 0x5 Return: 2
[ 10.817846] SX9310Going to Write Reg: 0x14 Value: 0xd
[ 10.822801] SX9310write_register Addr: 0x14 Val: 0xd Return: 2
[ 10.822805] SX9310Going to Write Reg: 0x15 Value: 0xc1
[ 10.828532] SX9310write_register Addr: 0x15 Val: 0xc1 Return: 2
[ 10.828535] SX9310Going to Write Reg: 0x16 Value: 0x20
[ 10.833554] SX9310write_register Addr: 0x16 Val: 0x20 Return: 2
[ 10.833557] SX9310Going to Write Reg: 0x17 Value: 0x4c
[ 10.839383] SX9310write_register Addr: 0x17 Val: 0x4c Return: 2
[ 10.839386] SX9310Going to Write Reg: 0x18 Value: 0x79
[ 10.844414] SX9310write_register Addr: 0x18 Val: 0x79 Return: 2
[ 10.844416] SX9310Going to Write Reg: 0x19 Value: 0x79
[ 10.850216] SX9310write_register Addr: 0x19 Val: 0x79 Return: 2
[ 10.850219] SX9310Going to Write Reg: 0x1a Value: 0x10
[ 10.855265] SX9310write_register Addr: 0x1a Val: 0x10 Return: 2
[ 10.855267] SX9310Going to Write Reg: 0x1b Value: 0x0
[ 10.861067] SX9310write_register Addr: 0x1b Val: 0x0 Return: 2
[ 10.861069] SX9310Going to Write Reg: 0x1c Value: 0x0
[ 10.866115] SX9310write_register Addr: 0x1c Val: 0x0 Return: 2
[ 10.866118] SX9310Going to Write Reg: 0x1d Value: 0x0
[ 10.871918] SX9310write_register Addr: 0x1d Val: 0x0 Return: 2
[ 10.871920] SX9310Going to Write Reg: 0x1e Value: 0x0
[ 10.877053] SX9310write_register Addr: 0x1e Val: 0x0 Return: 2
[ 10.877056] SX9310Going to Write Reg: 0x1f Value: 0x0
[ 10.882942] SX9310write_register Addr: 0x1f Val: 0x0 Return: 2
[ 10.882945] SX9310Going to Write Reg: 0x20 Value: 0x0
[ 10.888076] SX9310write_register Addr: 0x20 Val: 0x0 Return: 2
[ 10.888079] SX9310Going to Write Reg: 0x21 Value: 0x4
[ 10.893965] SX9310write_register Addr: 0x21 Val: 0x4 Return: 2
[ 10.893968] SX9310Going to Write Reg: 0x22 Value: 0x0
[ 10.899102] SX9310write_register Addr: 0x22 Val: 0x0 Return: 2
[ 10.899104] SX9310Going to Write Reg: 0x23 Value: 0x0
[ 10.905004] SX9310write_register Addr: 0x23 Val: 0x0 Return: 2
[ 10.905007] SX9310Going to Write Reg: 0x2a Value: 0x0
[ 10.910112] SX9310write_register Addr: 0x2a Val: 0x0 Return: 2
[ 10.910115] SX9310Going to Write Reg: 0x2b Value: 0x80
[ 10.916029] SX9310write_register Addr: 0x2b Val: 0x80 Return: 2
[ 10.916031] SX9310Going to Write Reg: 0x2c Value: 0xc
[ 10.921136] SX9310write_register Addr: 0x2c Val: 0xc Return: 2
[ 10.921139] SX9310Going to Write Reg: 0x10 Value: 0x27
[ 10.927053] SX9310write_register Addr: 0x10 Val: 0x27 Return: 2
[ 10.932161] SX9310write_register Addr: 0x10 Val: 0x2f Return: 2
[ 10.938076] SX9310write_register Addr: 0x30 Val: 0x1 Return: 2
[ 11.046582] SX9310write_register Addr: 0x0 Val: 0xff Return: 2
[ 11.046639] SX9310sx93XX_irq
[ 11.051721] SX9310read_register Addr: 0x0 Return: 0x90
[ 11.051725] SX9310Exiting initialize(). NIRQ = 0
[ 11.057626] SX9310read_register Addr: 0x0 Return: 0x0
[ 11.057628] SX9310Worker - Refresh Status 0
[ 11.057630] SX9310Looping Counter 0
[ 11.057632] SX9310Looping Counter 1
[ 11.057633] SX9310Looping Counter 2
[ 11.057635] SX9310Looping Counter 3
[ 11.057637] SX9310Looping Counter 4
[ 11.057638] SX9310Looping Counter 5
[ 11.057640] SX9310Looping Counter 6
[ 11.057642] SX9310Looping Counter 7
[ 11.062631] SX9310write_register Addr: 0x10 Val: 0x10 Return: 2
[ 11.068461] SX9310write_register Addr: 0x3 Val: 0x0 Return: 2
[ 11.070261] et580_init enter
[ 11.071214] etspi_probe initial
[ 11.071566] etspi_parse_dt: sleepPin=127
[ 11.071577] etspi_parse_dt: drdyPin=48
[ 11.071587] etspi_parse_dt: 3.3v power pin=45
[ 11.071598] etspi_parse_dt: 18v power pin=31
[ 11.071600] etspi_parse_dt is successful
[ 11.071602] etspi_platformInit
[ 11.071643] ets580: vdd_18v_Pin set to high
[ 11.072678] ets580: vcc_33v_Pin set to high
[ 11.074712] et580: reset to high
[ 11.074743] ets580: etspi_platformInit successful status=0
[ 11.076024] Egis navigation driver, egis_input device init
[ 11.077422] Egis navigation driver, uinput_egis_init
[ 11.077876] nav_input_thread enter
[ 11.080124] input: uinput-egis as /devices/virtual/input/input4
[ 11.081402] etspi_reset
[ 11.144043] add_timer ----
[ 11.144046] etspi_probe : initialize success 0
[ 11.144567] et580_init done
[ 11.147151] qcom,qpnp-rtc qpnp-rtc-7: rtc core: registered qpnp_rtc as rtc0
[ 11.148787] i2c /dev entries driver
[ 11.170195] /soc/qcom,cam_smmu/msm_cam_smmu_cb1: could not get #iommu-cells for /soc/qcom,iommu@1e00000
[ 11.172958] CAM-SMMU cam_populate_smmu_context_banks:1586 Invalid pointer of ctx : vfe_secure rc = -517
[ 11.172961] CAM-SMMU cam_smmu_probe:1636 Error: populating context banks
[ 11.173029] msm_cam_smmu: probe of soc:qcom,cam_smmu:msm_cam_smmu_cb2 failed with error -12
[ 11.173201] /soc/qcom,cam_smmu/msm_cam_smmu_cb3: could not get #iommu-cells for /soc/qcom,iommu@1e00000
[ 11.174640] /soc/qcom,cam_smmu/msm_cam_smmu_cb4: could not get #iommu-cells for /soc/qcom,iommu@1e00000
[ 11.176527] CAM-SMMU cam_populate_smmu_context_banks:1586 Invalid pointer of ctx : vfe_secure rc = -517
[ 11.176530] CAM-SMMU cam_smmu_probe:1636 Error: populating context banks
[ 11.176588] msm_cam_smmu: probe of soc:qcom,cam_smmu:msm_cam_smmu_cb2 failed with error -12
[ 11.184085] msm_camera_get_dt_vreg_data:1158 number of entries is 0 or not present in dts
[ 11.194518] msm_camera_get_dt_vreg_data:1158 number of entries is 0 or not present in dts
[ 11.197330] msm_camera_get_dt_vreg_data:1158 number of entries is 0 or not present in dts
[ 11.201202] msm_camera_get_dt_vreg_data:1158 number of entries is 0 or not present in dts
[ 11.204623] msm_camera_get_dt_vreg_data:1158 number of entries is 0 or not present in dts
[ 11.207956] msm_camera_get_dt_vreg_data:1158 number of entries is 0 or not present in dts
[ 11.210798] msm_actuator_platform_probe:1944 No valid actuator GPIOs data
[ 11.212263] msm_actuator_platform_probe:1944 No valid actuator GPIOs data
[ 11.215899] msm_eeprom_platform_probe failed 1673
[ 11.218980] msm_eeprom_platform_probe failed 1673
[ 11.222601] msm_flash_get_dt_data:1015 No valid flash GPIOs data
[ 11.225107] LED trigger switch_trigger failed to register (-17)
[ 11.225216] msm_flash_get_dt_data:1015 No valid flash GPIOs data
[ 11.226911] ------------[ cut here ]------------
[ 11.226922] WARNING: CPU: 1 PID: 1 at /home/lilu/work/motoE_lenovo_drvonly_o/kernel/msm-3.18/fs/sysfs/dir.c:31 sysfs_warn_dup+0x54/0x70()
[ 11.226924] sysfs: cannot create duplicate filename '/class/leds/torch-light0'
[ 11.226928] Modules linked in:
[ 11.226934] CPU: 1 PID: 1 Comm: swapper/0 Not tainted 3.18.66-g13d1896-dirty #6
[ 11.226945] [
[ 11.226955] [
[ 11.226963] [
[ 11.226970] [
[ 11.226977] [
[ 11.226984] [
[ 11.226994] [
[ 11.227001] [
[ 11.227008] [
[ 11.227018] [
[ 11.227028] [
[ 11.227035] [
[ 11.227043] [
[ 11.227050] [
[ 11.227057] [
[ 11.227064] [
[ 11.227071] [
[ 11.227079] [
[ 11.227087] [
[ 11.227095] [
[ 11.227103] [
[ 11.227112] [
[ 11.227144] ---[ end trace 25ca4b82fef70377 ]---
[ 11.227447] msm_torch_create_classdev:111 Failed to register 0 led dev. rc = -17
[ 11.227503] qcom,camera-flash: probe of soc:qcom,camera-flash@1 failed with error -17
[ 11.243583] MSM-CPP cpp_init_hardware:1005 CPP HW Version: 0x40030002
[ 11.243607] MSM-CPP cpp_init_hardware:1023 stream_cnt:0
[ 11.248711] CAM-SOC msm_camera_get_reg_base:787 err: mem resource vfe_fuse not found
[ 11.248715] CAM-SOC msm_camera_get_res_size:830 err: mem resource vfe_fuse not found
[ 11.252969] CAM-SOC msm_camera_get_reg_base:787 err: mem resource vfe_fuse not found
[ 11.252973] CAM-SOC msm_camera_get_res_size:830 err: mem resource vfe_fuse not found
[ 11.277568] __msm_jpeg_init:1537] Jpeg Device id 0
[ 11.277568] FG: fg_check_ima_exception: Initial ima_err_sts=0 ima_exp_sts=0 ima_hw_sts=0
[ 11.291029] FG: fg_probe: FG Probe success - FG Revision DIG:3.1 ANA:1.2 PMIC subtype=17
[ 11.301975] qpnp-smbcharger qpnp-smbcharger-17: node /soc/qcom,spmi@200f000/qcom,pmi8950@2/qcom,qpnp-smbcharger IO resource absent!
[ 11.303291] smbcharger_charger_otg: no parameters
[ 11.304159] SMBCHG: smbchg_hvdcp_enable_cb: smbchg_hvdcp_enable_cb enable 1
[ 11.393895] qpnp-smbcharger qpnp-smbcharger-17: node /soc/qcom,spmi@200f000/qcom,pmi8950@2/qcom,qpnp-smbcharger IO resource absent!
[ 11.396127] qpnp-smbcharger qpnp-smbcharger-17: SMBCHG successfully probe Charger version=SCHG_LITE Revision DIG:0.0 ANA:0.1 batt=1 dc=0 usb=0
[ 11.397573] unable to find DT imem DLOAD mode node
[ 11.397945] unable to find DT imem EDLOAD mode node
[ 11.404600] thermal thermal_zone2: failed to read out thermal zone 2
[ 11.407216] thermal thermal_zone3: failed to read out thermal zone 3
[ 11.409964] thermal thermal_zone4: failed to read out thermal zone 4
[ 11.412623] thermal thermal_zone5: failed to read out thermal zone 5
[ 11.417970] qpnp_vadc_read: Error reading die_temp
[ 11.486462] device-mapper: ioctl: 4.28.0-ioctl (2014-09-17) initialised: [email protected]
[ 11.487050] device-mapper: req-crypt: dm-req-crypt successfully initalized.
[ 11.487050]
[ 11.490070] sdhci: Secure Digital Host Controller Interface driver
[ 11.490071] sdhci: Copyright(c) Pierre Ossman
[ 11.490096] sdhci-pltfm: SDHCI platform and OF driver helper
[ 11.490972] qcom,leds-qpnp: probe of leds-qpnp-20 failed with error -10
[ 11.494710] qcom_ice_get_pdevice: found ice device e74c0900
[ 11.494714] qcom_ice_get_pdevice: matching platform device e9343740
[ 11.614818] qcom_ice 7803000.sdcc1ice: QC ICE 2.1.44 device found @0xefee0000
[ 11.615759] sdhci_msm 7824900.sdhci: No vmmc regulator found
[ 11.615764] sdhci_msm 7824900.sdhci: No vqmmc regulator found
[ 11.618330] mmc0: SDHCI controller on 7824900.sdhci [7824900.sdhci] using 32-bit ADMA in CMDQ mode
[ 11.698799] sdhci_msm 7864900.sdhci: sdhci_msm_probe: ICE device is not enabled
[ 11.785574] sdhci_msm 7864900.sdhci: No vmmc regulator found
[ 11.785579] sdhci_msm 7864900.sdhci: No vqmmc regulator found
[ 11.788225] mmc1: SDHCI controller on 7864900.sdhci [7864900.sdhci] using 32-bit ADMA in legacy mode
[ 11.839708] mmc_gpio_cd_irqt hot pulg irq
[ 11.841824] tz_log 8600720.tz-log: Hyp log service is not supported
[ 11.842160] hidraw: raw HID events driver (C) Jiri Kosina
[ 11.847682] usbcore: registered new interface driver usbhid
[ 11.847685] usbhid: USB HID core driver
[ 11.856828] ashmem: initialized
[ 11.858831] qpnp_coincell_charger_show_state: enabled=Y, voltage=3200 mV, resistance=2100 ohm
[ 11.871209] bimc-bwmon 408000.qcom,cpu-bwmon: BW HWmon governor registered.
[ 11.881699] devfreq soc:qcom,cpubw: Couldn't update frequency transition information.
[ 11.883861] devfreq soc:qcom,mincpubw: Couldn't update frequency transition information.
[ 11.893420] coresight-fuse a601c.fuse: Fuse initialized
[ 11.917311] mmc0: Out-of-interrupt timeout is 100[ms]
[ 11.917315] mmc0: BKOPS_EN equals 0x2
[ 11.917318] mmc0: eMMC FW version: 0x03
[ 11.917321] mmc0: CMDQ supported: depth: 16
[ 11.917323] mmc0: cache barrier support 0 flush policy 0
[ 11.954881] coresight-csr 6001000.csr: CSR initialized
[ 11.957861] coresight-tmc 6028000.tmc: Byte Counter feature enabled
[ 11.962567] sps:BAM 0x06044000 is registered.
[ 11.962568] coresight-tmc 6028000.tmc: TMC initialized
[ 11.965066] coresight-tmc 6027000.tmc: TMC initialized
[ 11.974728] nidnt boot config: 0
[ 11.974735] coresight-tpiu 6020000.tpiu: NIDnT hw support disabled
[ 11.974740] coresight-tpiu 6020000.tpiu: NIDnT on SDCARD only mode
[ 11.975872] coresight-tpiu 6020000.tpiu: TPIU initialized
[ 11.986944] coresight-replicator 6026000.replicator: REPLICATOR initialized
[ 11.996147] coresight-dbgui 6108000.dbgui: DebugUI capture enabled
[ 11.997715] coresight-dbgui 6108000.dbgui: DebugUI initializaed
[ 12.000855] coresight-stm 6002000.stm: STM initialized
[ 12.002744] coresight-hwevent 6101000.hwevent: Hardware Event driver initialized
[ 12.008898] coresight-etmv4 61bc000.etm: ETMv4 initialized
[ 12.013186] coresight-etmv4 61bd000.etm: ETMv4 initialized
[ 12.017444] coresight-etmv4 61be000.etm: ETMv4 initialized
[ 12.021725] coresight-etmv4 61bf000.etm: ETMv4 initialized
[ 12.026015] coresight-etmv4 619c000.etm: ETMv4 initialized
[ 12.030356] coresight-etmv4 619d000.etm: ETMv4 initialized
[ 12.034743] coresight-etmv4 619e000.etm: ETMv4 initialized
[ 12.039071] coresight-etmv4 619f000.etm: ETMv4 initialized
[ 12.042291] coresight-remote-etm soc:wcn_etm0: Remote ETM initialized
[ 12.044616] coresight-remote-etm soc:rpm_etm0: Remote ETM initialized
[ 12.046319] coresight-remote-etm soc:audio_etm0: Remote ETM initialized
[ 12.048231] coresight-remote-etm soc:modem_etm0: Remote ETM initialized
[ 12.049372] coresight-qpdi: probe of 1941000.qpdi failed with error -1
[ 12.050598] sensors-ssc soc:qcom,msm-ssc-sensors: msm_ssc_sensors_dt_parse: get qdsp timer cntpct hi offset fail
[ 12.050602] sensors-ssc soc:qcom,msm-ssc-sensors: slpi_loader_init_sysfs: Could not parse dt
[ 12.054566] usbcore: registered new interface driver snd-usb-audio
[ 12.121474] msm-pcm-lpa soc:qcom,msm-pcm-lpa: msm_pcm_probe: dev name soc:qcom,msm-pcm-lpa
[ 12.141870] u32 classifier
[ 12.141872] Actions configured
[ 12.142031] Netfilter messages via NETLINK v0.30.
[ 12.142393] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 12.147318] ctnetlink v0.93: registering with nfnetlink.
[ 12.158371] xt_time: kernel timezone is -0000
[ 12.159472] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 12.161604] arp_tables: (C) 2002 David S. Miller
[ 12.162094] TCP: cubic registered
[ 12.162117] Initializing XFRM netlink socket
[ 12.174248] NET: Registered protocol family 10
[ 12.185928] mip6: Mobile IPv6
[ 12.186092] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 12.189335] sit: IPv6 over IPv4 tunneling driver
[ 12.194385] NET: Registered protocol family 17
[ 12.194520] NET: Registered protocol family 15
[ 12.196272] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 12.196339] Bridge firewalling registered
[ 12.196362] Ebtables v2.0 registered
[ 12.197128] Bluetooth: eaa9fea8
[ 12.197197] Bluetooth: eaa9fea8
[ 12.197271] Bluetooth: eaa9feb8
[ 12.197273] Bluetooth: eaa9fe90
[ 12.197326] Bluetooth: eaa9fe90
[ 12.197351] Bluetooth: eaa9fe88
[ 12.197398] Bluetooth: eaa9fec8
[ 12.197632] Bluetooth: eaa9fec8
[ 12.197632] _core: L2TP core driver, V2.0
[ 12.197712] _ppp: PPPoL2TP kernel driver, V2.0
[ 12.197737] _ip: L2TP IP encapsulation support (L2TPv3)
[ 12.199460] _netlink: L2TP netlink interface
[ 12.199635] _eth: L2TP ethernet pseudowire support (L2TPv3)
[ 12.199746] _debugfs: L2TP debugfs support
[ 12.199770] _ip6: L2TP IP encapsulation support for IPv6 (L2TPv3)
[ 12.204652] NET: Registered protocol family 27
[ 12.232352] subsys-pil-tz c200000.qcom,lpass: for adsp segments only will be dumped.
[ 12.240366] subsys-pil-tz a21b000.qcom,pronto: for wcnss segments only will be dumped.
[ 12.255714] pil-q6v5-mss 4080000.qcom,mss: for modem segments only will be dumped.
[ 12.259194] msm_otg 78db000.usb: phy_reset: success
[ 12.261045] Registering SWP/SWPB emulation handler
[ 12.261244] Creating CPU group 0
[ 12.261264] Init CPU0 state
[ 12.261266] Init CPU1 state
[ 12.261267] Init CPU2 state
[ 12.261268] Init CPU3 state
[ 12.262332] Creating CPU group 4
[ 12.262356] Init CPU4 state
[ 12.262358] Init CPU5 state
[ 12.262359] Init CPU6 state
[ 12.262361] Init CPU7 state
[ 12.269038] Loading compiled-in X.509 certificates
[ 12.273853] Loaded X.509 cert 'Magrathea: Glacier signing key: 88783154c63aaf9fa7ec5c91df084504bdad665b'
[ 12.274262] registered taskstats version 1
[ 12.295366] fastrpc soc:qcom,adsprpc-mem: for adsp_rh segments only will be dumped.
[ 12.308459] RNDIS_IPA module is loaded.
[ 12.308459] file system registered
[ 12.309307] mbim_init: initialize 1 instances
[ 12.310199] mbim_init: Initialized 1 ports
[ 12.333035] rndis_qc_init: initialize rndis QC instance
[ 12.337119] Number of LUNs=8
[ 12.337186] Mass Storage Function, version: 2009/09/11
[ 12.337228] LUN: removable file: (no medium)
[ 12.337392] Number of LUNs=1
[ 12.338185] LUN: removable file: (no medium)
[ 12.338204] Number of LUNs=1
[ 12.338943] cmdq_host_alloc_tdl: desc_size: 512 data_sz: 126976 slot-sz: 16
[ 12.340708] desc-base: 0xf0b3a000 trans-base: 0xf0bbc000
[ 12.340708] desc_dma 0xf685a000 trans_dma: 0xf6d80000
[ 12.340742] mmc0: CMDQ enabled on card
[ 12.340769] mmc0: new HS400 MMC card at address 0001
[ 12.343446] android_usb gadget: android_usb ready
[ 12.343455] msm_hsusb msm_hsusb: [ci13xxx_start] hw_ep_max = 32
[ 12.343508] msm_hsusb msm_hsusb: CI13XXX_CONTROLLER_UDC_STARTED_EVENT received
[ 12.348763] gpio-keys soc:gpio_keys: Failed to request GPIO 127, error -16
[ 12.349302] gpio-keys: probe of soc:gpio_keys failed with error -16
[ 12.351047] qcom,qpnp-rtc qpnp-rtc-7: setting system clock to 1970-01-05 21:37:21 UTC (423441)
[ 12.351211] sdhci_msm_pm_qos_cpu_init (): voted for group #0 (mask=0xf) latency=2 (0xe7358a40)
[ 12.351351] sdhci_msm_pm_qos_cpu_init (): voted for group #1 (mask=0xf0) latency=2 (0xe7358a48)
[ 12.351901] mmcblk0: mmc0:0001 GX6BMB 29.1 GiB
[ 12.352936] mmcblk0rpmb: mmc0:0001 GX6BMB partition 3 4.00 MiB
[ 12.364111] parse_cpu_levels: idx 1 900
[ 12.364384] calculate_residency: residency < 0 for LPM
[ 12.364386] parse_cpu_levels: idx 1 400
[ 12.367843] ipa_get_transport_type:2302 IPA HW is not supported
[ 12.385333] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18 p19 p20 p21 p22 p23 p24 p25 p26 p27 p28 p29 p30 p31 p32 p33 p34 p35 p36 p37 p38 p39 p40 p41 p42 p43 p44 p45 p46 p47 p48 p49 p50 p51 p52 p53 p54 p55
[ 12.423274] msm_otg 78db000.usb: USB in low power mode
[ 12.425253] qcom,cc-debug-8952 1874000.qcom,cc-debug: Registered Debug Mux successfully
[ 12.460082] msm8952-asoc-wcd c051000.sound: default codec configured
[ 12.466561] msm8952-asoc-wcd c051000.sound: ASoC: platform (null) not registered
[ 12.466782] msm8952-asoc-wcd c051000.sound: snd_soc_register_card failed (-517)
[ 12.474857] mem_acc_corner: disabling
[ 12.474907] adv_vreg: disabling
[ 12.475007] clock_late_init: Removing enables held for handed-off clocks
[ 12.532399] msm8952-asoc-wcd c051000.sound: default codec configured
[ 12.538849] msm8952-asoc-wcd c051000.sound: ASoC: platform (null) not registered
[ 12.538907] msm8952-asoc-wcd c051000.sound: snd_soc_register_card failed (-517)
[ 12.612603] ALSA device list:
[ 12.612607] No soundcards found.
182] [HXTP] himax_touch_information:HX_INT_IS_EDGE =1 VERSE =0,HX_Y_RES =1440,HX_X_RES=720
[ 12.694028] [HXTP] calcDataSize: coord_data_size: 20, area_data_size:8, raw_data_frame_size:91, raw_data_nframes:1
[ 12.704295] [HXTP] himax_chip_common_probe: calcDataSize complete
[ 12.710347] [HXTP] himax_chip_common_probe: Use Protocol Type B
[ 12.716377] [HXTP] input_set_abs_params: mix_x 0, max_x 720, min_y 0, max_y 1440
[ 12.725359] input: himax-touchscreen as /devices/virtual/input/input6
[ 12.732252] [HXTP] himax_report_data_init: rawdata_frame_size = 7
[ 12.737370] [HXTP] himax_report_data_init: ic_data->HX_MAX_PT:5,hx_raw_cnt_max:1,hx_raw_cnt_rmd:1,g_hx_rawdata_size:91,hx_touch_data->touch_info_size:32
[ 12.751793] [HXTP] himax_int_register_trigger edge triiger falling
[HXTP] himax_ts_register_interrupt: irq enabled at qpio: 221
[ 12.824009] [HXTP] himax_sw_reset: SYSTEM_RST_in_Probe_end
[ 12.830172] Freeing unused kernel memory: 856K
[ 12.842754] init: init first stage started!
[ 12.866631] msm8952-asoc-wcd c051000.sound: default codec configured
[ 12.878398] msm8952-asoc-wcd c051000.sound: ASoC: platform (null) not registered
[ 12.884944] msm8952-asoc-wcd c051000.sound: snd_soc_register_card failed (-517)
[ 12.997567] init: Coldboot took 0.143054 seconds
[ 13.047310] EXT4-fs (mmcblk0p54): mounted filesystem with ordered data mode. Opts: barrier=1,discard
[ 13.055857] init: [libfs_mgr]__mount(source=/dev/block/platform/soc/7824900.sdhci/by-name/system,target=/system,type=ext4)=0
[ 13.078321] EXT4-fs (mmcblk0p52): mounted filesystem with ordered data mode. Opts: barrier=1,discard
[ 13.086857] init: [libfs_mgr]__mount(source=/dev/block/platform/soc/7824900.sdhci/by-name/vendor,target=/vendor,type=ext4)=0
[ 13.098345] init: Skipped setting INIT_AVB_VERSION (not in recovery mode)
[ 13.104745] init: Loading SELinux policy
[ 14.079100] audit: type=1403 audit(423443.219:2): policy loaded auid=4294967295 ses=4294967295
[ 14.087931] selinux: SELinux: Loaded policy from /vendor/etc/selinux/precompiled_sepolicy
[ 14.087931]
[ 14.098443] audit: type=1404 audit(423443.239:3): enforcing=1 old_enforcing=0 auid=4294967295 ses=4294967295
[ 14.144884] selinux: SELinux: Loaded file_contexts
[ 14.144884]
[ 14.153447] random: init urandom read with 107 bits of entropy available
[ 14.162150] init: init second stage started!
[ 14.213433] selinux: SELinux: Loaded file_contexts
[ 14.213433]
[ 14.220597] selinux: SELinux: Loaded property_contexts from /system/etc/selinux/plat_property_contexts & /vendor/etc/selinux/nonplat_property_contexts.
[ 14.220597]
[ 14.234654] init: Running restorecon...
[ 14.804121] of_batterydata_get_best_profile: 64_lenovo_bl270_4090mah_averaged_masterslave_jun20th2016_power found
[ 14.825379] FG: fg_batt_profile_init: Battery SOC: 92, V: 4176153uV
[ 14.831099] of_batterydata_get_best_profile: 64_lenovo_bl270_4090mah_averaged_masterslave_jun20th2016_power found
[ 16.928037] init: waitpid failed: No child processes
[ 16.940114] init: Couldn't load properties from /odm/default.prop: No such file or directory
[ 16.950324] init: Created socket '/dev/socket/property_service', mode 666, user 0, group 0
[ 16.957985] init: Parsing file /init.rc...
[ 16.962293] init: Added '/init.environ.rc' to import list
[ 16.967068] init: Added '/init.usb.rc' to import list
[ 16.972086] init: Added '/init.qcom.rc' to import list
[ 16.977231] init: Added '/vendor/etc/init/hw/init.qcom.rc' to import list
[ 16.983971] init: Added '/init.usb.configfs.rc' to import list
[ 16.989795] init: Added '/init.zygote32.rc' to import list
[ 16.997502] init: Parsing file /init.environ.rc...
[ 17.001558] init: Parsing file /init.usb.rc...
[ 17.006655] init: Parsing file /init.qcom.rc...
[ 17.010312] init: could not import file '/init.qcom.rc' from '/init.rc': No such file or directory
[ 17.020837] init: Parsing file /vendor/etc/init/hw/init.qcom.rc...
[ 17.028159] init: Added '/vendor/etc/init/hw/init.qcom.usb.rc' to import list
[ 17.034364] init: Added '/vendor/etc/init/hw/init.msm.usb.configfs.rc' to import list
[ 17.042103] init: Added '/vendor/etc/init/hw/init.target.rc' to import list
[ 17.049073] init: Added '/vendor/etc/init/hw/init.qcom.factory.rc' to import list
[ 17.056532] init: Added '/vendor/etc/init/hw/init.qcom.test.rc' to import list
[ 17.064364] init: /vendor/etc/init/hw/init.qcom.rc: 181: chown requires between 2 and 3 arguments
[ 17.072559] init:
[ 17.074615] init: /vendor/etc/init/hw/init.qcom.rc: 182: chmod requires 2 arguments
[ 17.082194] init:
[ 17.086519] init: decode_uid: Unable to find UID for 'net_bt_stack'; returning UINT_MAX
[ 17.093556] init: /vendor/etc/init/hw/init.qcom.rc: 601: user requires 1 argument
[ 17.101002] init:
[ 17.105922] init: Parsing file /vendor/etc/init/hw/init.qcom.usb.rc...
[ 17.128158] init: Parsing file /vendor/etc/init/hw/init.msm.usb.configfs.rc...
[ 17.143368] init: Parsing file /vendor/etc/init/hw/init.target.rc...
[ 17.149847] init: Added 'init.carrier.rc' to import list
[ 17.154885] init: ignored duplicate definition of service 'time_daemon'
[ 17.161256] init: /vendor/etc/init/hw/init.target.rc: 237: invalid keyword 'load_all_props'
[ 17.169095] init:
[ 17.171817] init: Parsing file init.carrier.rc...
[ 17.176236] init: Parsing file /vendor/etc/init/hw/init.qcom.factory.rc...
[ 17.183918] init: Parsing file /vendor/etc/init/hw/init.qcom.test.rc...
[ 17.190573] init: decode_uid: Unable to find UID for 'qcom_diag'; returning UINT_MAX
[ 17.197508] init: Parsing file /init.usb.configfs.rc...
[ 17.204969] init: Parsing file /init.zygote32.rc...
[ 17.209324] init: Parsing directory /system/etc/init...
[ 17.214936] init: Parsing file /system/etc/init/[email protected]...
[ 17.222917] init: Parsing file /system/etc/init/atrace.rc...
[ 17.230213] init: Parsing file /system/etc/init/atrace_userdebug.rc...
[ 17.236909] init: Parsing file /system/etc/init/audioserver.rc...
[ 17.242983] init: Parsing file /system/etc/init/bootanim.rc...
[ 17.248659] init: Parsing file /system/etc/init/bootstat.rc...
[ 17.254558] init: Parsing file /system/etc/init/cameraserver.rc...
[ 17.260562] init: Parsing file /system/etc/init/dpmd.rc...
[ 17.266224] init: Parsing file /system/etc/init/drmserver.rc...
[ 17.271935] init: Parsing file /system/etc/init/dumpstate.rc...
[ 17.277965] init: Parsing file /system/etc/init/gatekeeperd.rc...
[ 17.283888] init: Parsing file /system/etc/init/hwservicemanager.rc...
[ 17.290554] init: Parsing file /system/etc/init/init-debug.rc...
[ 17.296528] init: Parsing file /system/etc/init/init.qti.fm.rc...
[ 17.302488] init: Parsing file /system/etc/init/installd.rc...
[ 17.309351] init: Parsing file /system/etc/init/keystore.rc...
[ 17.315051] init: Parsing file /system/etc/init/lmkd.rc...
[ 17.320441] init: Parsing file /system/etc/init/logcatd.rc...
[ 17.326581] init: Parsing file /system/etc/init/logd.rc...
[ 17.331937] init: Parsing file /system/etc/init/logtagd.rc...
[ 17.337650] init: Parsing file /system/etc/init/mdnsd.rc...
[ 17.343119] init: Parsing file /system/etc/init/mediadrmserver.rc...
[ 17.349529] init: Parsing file /system/etc/init/mediaextractor.rc...
[ 17.355868] init: Parsing file /system/etc/init/mediametrics.rc...
[ 17.361930] init: Parsing file /system/etc/init/mediaserver.rc...
[ 17.368173] init: Parsing file /system/etc/init/mtpd.rc...
[ 17.373494] init: Parsing file /system/etc/init/netd.rc...
[ 17.379071] init: Parsing file /system/etc/init/perfprofd.rc...
[ 17.384955] init: Parsing file /system/etc/init/racoon.rc...
[ 17.390546] init: Parsing file /system/etc/init/servicemanager.rc...
[ 17.396969] init: Parsing file /system/etc/init/storaged.rc...
[ 17.402678] init: Parsing file /system/etc/init/surfaceflinger.rc...
[ 17.409129] init: Parsing file /system/etc/init/tombstoned.rc...
[ 17.415087] init: Parsing file /system/etc/init/uncrypt.rc...
[ 17.420755] init: Parsing file /system/etc/init/vdc.rc...
[ 17.426183] init: Parsing file /system/etc/init/vold.rc...
[ 17.431656] init: Parsing file /system/etc/init/webview_zygote32.rc...
[ 17.438241] init: Parsing file /system/etc/init/wfdservice.rc...
[ 17.444195] init: Parsing file /system/etc/init/wifi-events.rc...
[ 17.450530] init: Parsing file /system/etc/init/wificond.rc...
[ 17.456376] init: Parsing directory /vendor/etc/init...
[ 17.460833] init: Parsing file /vendor/etc/init/[email protected]...
[ 17.469673] init: Parsing file /vendor/etc/init/[email protected]...
[ 17.479124] init: Parsing file /vendor/etc/init/[email protected]...
[ 17.487906] init: Parsing file /vendor/etc/init/[email protected]...
[ 17.496853] init: Parsing file /vendor/etc/init/[email protected]...
[ 17.505415] init: Parsing file /vendor/etc/init/[email protected]...
[ 17.513228] init: Parsing file /vendor/etc/init/[email protected]...
[ 17.522184] init: Parsing file /vendor/etc/init/[email protected]...
[ 17.531381] init: Parsing file /vendor/etc/init/[email protected]...
[ 17.540524] init: Parsing file /vendor/etc/init/[email protected]...
[ 17.548635] init: Parsing file /vendor/etc/init/[email protected]...
[ 17.557415] init: Parsing file /vendor/etc/init/[email protected]...
[ 17.565477] init: Parsing file /vendor/etc/init/[email protected]...
[ 17.573825] init: Parsing file /vendor/etc/init/[email protected]...
[ 17.582224] init: Parsing file /vendor/etc/init/[email protected]...
[ 17.590296] init: Parsing file /vendor/etc/init/[email protected]...
[ 17.598569] init: Parsing file /vendor/etc/init/[email protected]...
[ 17.606450] init: Parsing file /vendor/etc/init/[email protected]...
[ 17.614788] init: Parsing file /vendor/etc/init/[email protected]...
[ 17.622686] init: Parsing file /vendor/etc/init/[email protected]...
[ 17.631711] init: Parsing file /vendor/etc/init/hostapd.android.rc...
[ 17.638174] init: Parsing file /vendor/etc/init/rild.rc...
[ 17.643467] init: Parsing file /vendor/etc/init/[email protected]...
[ 17.651399] init: Parsing file /vendor/etc/init/[email protected]...
[ 17.659825] init: Parsing file /vendor/etc/init/[email protected]...
[ 17.667320] init: Parsing file /vendor/etc/init/[email protected]...
[ 17.675633] init: Parsing file /vendor/etc/init/[email protected]...
[ 17.683702] init: Parsing file /vendor/etc/init/[email protected]...
[ 17.692105] init: Parsing file /vendor/etc/init/[email protected]...
[ 17.701063] init: Parsing file /vendor/etc/init/vndservicemanager.rc...
[ 17.707783] init: Parsing file /odm/etc/init...
[ 17.711555] init: processing action (early-init)
[ 17.717408] init: starting service 'ueventd'...
[ 17.723675] init: failed to open /acct/uid_0/pid_384/cgroup.procs: No such file or directory
[ 17.731234] init: createProcessGroup(0, 384) failed for service 'ueventd': No such file or directory
[ 17.734935] ueventd: ueventd started!
[ 17.736190] ueventd: /sys/ rule /sys/devices/platform/trusty.* trusty_version
[ 17.736336] ueventd: /sys/ rule /sys/devices/virtual/input/input* enable
[ 17.736480] ueventd: /sys/ rule /sys/devices/virtual/input/input* poll_delay
[ 17.736621] ueventd: /sys/ rule /sys/devices/virtual/usb_composite/* enable
[ 17.736803] ueventd: /sys/ rule /sys/devices/system/cpu/cpu* cpufreq/scaling_max_freq
[ 17.736980] ueventd: /sys/ rule /sys/devices/system/cpu/cpu* cpufreq/scaling_min_freq
[ 17.766246] ueventd: /sys/ rule /sys/devices/soc/a000000.qcom,wcnss-wlan/net/wlan0/queues/rx-* rps_cpus
[ 17.766411] ueventd: /sys/ rule /sys/devices/soc/a000000.qcom,wcnss-wlan/net/p2p0/queues/rx-* rps_cpus
[ 17.766979] ueventd: /sys/ rule /sys/devices/virtual/smdpkt/smdcntl* open_timeout
[ 17.767173] ueventd: /sys/ rule /sys/devices/i2c-12/12-* pollrate_ms
[ 17.767273] ueventd: /sys/ rule /sys/devices/f9925000.i2c/i2c-0/0-* enable
[ 17.767377] ueventd: /sys/ rule /sys/devices/f9925000.i2c/i2c-0/0-* poll_delay
[ 17.767479] ueventd: /sys/ rule /sys/devices/soc.0/78b6000.i2c/i2c-0/0-* enable
[ 17.767580] ueventd: /sys/ rule /sys/devices/soc.0/78b6000.i2c/i2c-0/0-* poll_delay
[ 17.767700] ueventd: /sys/ rule /sys/devices/soc.0/78b6000.i2c/i2c-0/0-* enable_wakeup
[ 17.767825] ueventd: /sys/ rule /sys/devices/soc.0/78b6000.i2c/i2c-0/0-* max_latency
[ 17.767924] ueventd: /sys/ rule /sys/devices/soc.0/78b6000.i2c/i2c-0/0-* flush
[ 17.768028] ueventd: /sys/ rule /sys/devices/soc.0/78b6000.i2c/i2c-0/0-* calibrate
[ 17.768129] ueventd: /sys/ rule /sys/devices/soc.0/78b5000.i2c/i2c-1/1-* enable
[ 17.768230] ueventd: /sys/ rule /sys/devices/soc.0/78b5000.i2c/i2c-1/1-* poll_delay
[ 17.768348] ueventd: /sys/ rule /sys/devices/soc.0/78b5000.i2c/i2c-1/1-* enable_wakeup
[ 17.768472] ueventd: /sys/ rule /sys/devices/soc.0/78b5000.i2c/i2c-1/1-* max_latency
[ 17.768573] ueventd: /sys/ rule /sys/devices/soc.0/78b5000.i2c/i2c-1/1-* flush
[ 17.768674] ueventd: /sys/ rule /sys/devices/soc.0/78b5000.i2c/i2c-1/1-* calibrate
[ 17.768792] ueventd: /sys/ rule /sys/devices/virtual/optical_sensors/proximity ps_adc
[ 17.768933] ueventd: /sys/ rule /sys/devices/virtual/optical_sensors/proximity ps_poll_delay
[ 17.769071] ueventd: /sys/ rule /sys/devices/virtual/optical_sensors/lightsensor ls_auto
[ 17.769229] ueventd: /sys/ rule /sys/devices/virtual/optical_sensors/lightsensor ls_poll_delay
[ 17.769353] ueventd: /sys/ rule /sys/devices/virtual/input/input* poll
[ 17.769453] ueventd: /sys/ rule /sys/devices/virtual/input/input* pollrate_ms
[ 17.769572] ueventd: /sys/ rule /sys/devices/soc/78b7000.i2c/i2c-3/3-0020/input/input* secure_touch
[ 17.769713] ueventd: /sys/ rule /sys/devices/soc/78b7000.i2c/i2c-3/3-0020/input/input* secure_touch_enable
[ 17.769850] ueventd: /sys/ rule /sys/devices/soc/78b7000.i2c/i2c-3/3-0038/input/input* secure_touch
[ 17.769993] ueventd: /sys/ rule /sys/devices/soc/78b7000.i2c/i2c-3/3-0038/input/input* secure_touch_enable
[ 17.770134] ueventd: /sys/ rule /sys/devices/soc/78b7000.i2c/i2c-3/3-004b/input/input* secure_touch
[ 17.770274] ueventd: /sys/ rule /sys/devices/soc/78b7000.i2c/i2c-3/3-004b/input/input* secure_touch_enable
[ 17.770413] ueventd: /sys/ rule /sys/devices/soc/c179000.i2c/i2c-5/5-0020/input/input* secure_touch
[ 17.770552] ueventd: /sys/ rule /sys/devices/soc/c179000.i2c/i2c-5/5-0020/input/input* secure_touch_enable
[ 17.770675] ueventd: /sys/ rule /sys/devices/virtual/input/input* enable_ps_sensor
[ 17.770775] ueventd: /sys/ rule /sys/devices/virtual/input/input* set_delay_ms
[ 17.770875] ueventd: /sys/ rule /sys/devices/virtual/input/input* do_flush
[ 17.771016] ueventd: /sys/ rule /sys/devices/soc/600000.qcom,pcie/pci0000:00/0000:00:00.0/0000:01:00.0/net/wlan0/queues/rx-* rps_cpus
[ 17.771154] ueventd: /sys/ rule /sys/devices/soc/600000.qcom,pcie/pci0000:00/0000:00:00.0/0000:01:00.0/net/p2p0/queues/rx-* rps_cpus
[ 17.771296] ueventd: /sys/ rule /sys/bus/pci/drivers/wil6210* 0000:01:00.0/wil6210/fst_link_loss
[ 17.771423] ueventd: /sys/ rule /sys/bus/pci/drivers/wil6210* 0000:01:00.0/wil6210/thermal_throttling
[ 17.771563] ueventd: /sys/ rule /sys/bus/pci/drivers/wil6210* 0000:01:00.0/net/wigig0/queues/rx-0/rps_cpus
[ 17.771680] ueventd: /sys/ rule /sys/bus/pci/drivers/wil6210* 0000:01:00.0/net/wigig0/gro_flush_timeout
[ 17.771782] ueventd: /sys/ rule /sys/devices/virtual/net/bond0 queues/rx-0/rps_cpus
[ 17.783614] selinux: SELinux: Loaded file_contexts
[ 17.783614]
[ 17.809480] selinux: SELinux: Loaded file_contexts
[ 17.809480]
[ 18.148453] init: Command 'start ueventd' action=early-init (/init.rc:30) returned 0 took 431.073ms.
[ 18.160293] init: processing action (wait_for_coldboot_done)
[ 19.075134] audit: type=1400 audit(423448.219:4): avc: granted { read } for pid=384 comm="ueventd" name="cmdline" dev="proc" ino=4026532288 scontext=u:r:ueventd:s0 tcontext=u:object_r:proc:s0 tclass=file
[ 19.092658] audit: type=1400 audit(423448.229:5): avc: granted { read open } for pid=384 comm="ueventd" path="/proc/cmdline" dev="proc" ino=4026532288 scontext=u:r:ueventd:s0 tcontext=u:object_r:proc:s0 tclass=file
[ 19.111996] audit: type=1400 audit(423448.249:6): avc: granted { getattr } for pid=384 comm="ueventd" path="/proc/cmdline" dev="proc" ino=4026532288 scontext=u:r:ueventd:s0 tcontext=u:object_r:proc:s0 tclass=file
[ 21.024792] random: nonblocking pool is initialized
[ 21.585378] ueventd: fixup /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq 1000 1000 664
[ 21.593281] ueventd: fixup /sys/devices/system/cpu/cpu0/cpufreq/scaling_min_freq 1000 1000 664
[ 21.605349] ueventd: fixup /sys/devices/system/cpu/cpu1/cpufreq/scaling_max_freq 1000 1000 664
[ 21.613189] ueventd: fixup /sys/devices/system/cpu/cpu1/cpufreq/scaling_min_freq 1000 1000 664
[ 21.624391] ueventd: fixup /sys/devices/system/cpu/cpu2/cpufreq/scaling_max_freq 1000 1000 664
[ 21.632231] ueventd: fixup /sys/devices/system/cpu/cpu2/cpufreq/scaling_min_freq 1000 1000 664
[ 21.643400] ueventd: fixup /sys/devices/system/cpu/cpu3/cpufreq/scaling_max_freq 1000 1000 664
[ 21.651262] ueventd: fixup /sys/devices/system/cpu/cpu3/cpufreq/scaling_min_freq 1000 1000 664
[ 21.662476] ueventd: fixup /sys/devices/system/cpu/cpu4/cpufreq/scaling_max_freq 1000 1000 664
[ 21.670393] ueventd: fixup /sys/devices/system/cpu/cpu4/cpufreq/scaling_min_freq 1000 1000 664
[ 21.682162] ueventd: fixup /sys/devices/system/cpu/cpu5/cpufreq/scaling_max_freq 1000 1000 664
[ 21.690033] ueventd: fixup /sys/devices/system/cpu/cpu5/cpufreq/scaling_min_freq 1000 1000 664
[ 21.701211] ueventd: fixup /sys/devices/system/cpu/cpu6/cpufreq/scaling_max_freq 1000 1000 664
[ 21.709067] ueventd: fixup /sys/devices/system/cpu/cpu6/cpufreq/scaling_min_freq 1000 1000 664
[ 21.720238] ueventd: fixup /sys/devices/system/cpu/cpu7/cpufreq/scaling_max_freq 1000 1000 664
[ 21.728104] ueventd: fixup /sys/devices/system/cpu/cpu7/cpufreq/scaling_min_freq 1000 1000 664
[ 22.219652] ueventd: fixup /sys/devices/virtual/input/input0/enable 0 1004 660
[ 22.226182] ueventd: fixup /sys/devices/virtual/input/input0/poll_delay 0 1004 660
[ 22.233718] ueventd: fixup /sys/devices/virtual/input/input0/poll 1004 1000 660
[ 22.241021] ueventd: fixup /sys/devices/virtual/input/input0/pollrate_ms 1004 1000 660
[ 22.248978] ueventd: fixup /sys/devices/virtual/input/input0/enable_ps_sensor 1000 1004 660
[ 22.257258] ueventd: fixup /sys/devices/virtual/input/input0/set_delay_ms 1000 1004 660
[ 22.265243] ueventd: fixup /sys/devices/virtual/input/input0/do_flush 1000 1004 660
[ 22.291145] ueventd: fixup /sys/devices/virtual/input/input0/event0/enable 0 1004 660
[ 22.298830] ueventd: fixup /sys/devices/virtual/input/input0/event0/poll_delay 0 1004 660
[ 22.306520] ueventd: fixup /sys/devices/virtual/input/input0/event0/poll 1004 1000 660
[ 22.314414] ueventd: fixup /sys/devices/virtual/input/input0/event0/pollrate_ms 1004 1000 660
[ 22.322940] ueventd: fixup /sys/devices/virtual/input/input0/event0/enable_ps_sensor 1000 1004 660
[ 22.331853] ueventd: fixup /sys/devices/virtual/input/input0/event0/set_delay_ms 1000 1004 660
[ 22.340431] ueventd: fixup /sys/devices/virtual/input/input0/event0/do_flush 1000 1004 660
[ 22.356773] ueventd: fixup /sys/devices/virtual/input/input2/enable 0 1004 660
[ 22.363269] ueventd: fixup /sys/devices/virtual/input/input2/poll_delay 0 1004 660
[ 22.370854] ueventd: fixup /sys/devices/virtual/input/input2/poll 1004 1000 660
[ 22.378135] ueventd: fixup /sys/devices/virtual/input/input2/pollrate_ms 1004 1000 660
[ 22.386096] ueventd: fixup /sys/devices/virtual/input/input2/enable_ps_sensor 1000 1004 660
[ 22.394366] ueventd: fixup /sys/devices/virtual/input/input2/set_delay_ms 1000 1004 660
[ 22.402323] ueventd: fixup /sys/devices/virtual/input/input2/do_flush 1000 1004 660
[ 22.440545] ueventd: fixup /sys/devices/virtual/input/input2/event1/enable 0 1004 660
[ 22.447735] ueventd: fixup /sys/devices/virtual/input/input2/event1/poll_delay 0 1004 660
[ 22.455911] ueventd: fixup /sys/devices/virtual/input/input2/event1/poll 1004 1000 660
[ 22.463768] ueventd: fixup /sys/devices/virtual/input/input2/event1/pollrate_ms 1004 1000 660
[ 22.472353] ueventd: fixup /sys/devices/virtual/input/input2/event1/enable_ps_sensor 1000 1004 660
[ 22.481239] ueventd: fixup /sys/devices/virtual/input/input2/event1/set_delay_ms 1000 1004 660
[ 22.489837] ueventd: fixup /sys/devices/virtual/input/input2/event1/do_flush 1000 1004 660
[ 22.505707] ueventd: fixup /sys/devices/virtual/input/input2/capsense_top/enable 0 1004 660
[ 22.513367] ueventd: fixup /sys/devices/virtual/input/input2/capsense_top/poll_delay 0 1004 660
[ 22.522115] ueventd: fixup /sys/devices/virtual/input/input2/capsense_top/poll 1004 1000 660
[ 22.530518] ueventd: fixup /sys/devices/virtual/input/input2/capsense_top/pollrate_ms 1004 1000 660
[ 22.539551] ueventd: fixup /sys/devices/virtual/input/input2/capsense_top/enable_ps_sensor 1000 1004 660
[ 22.549486] ueventd: fixup /sys/devices/virtual/input/input2/capsense_top/set_delay_ms 1000 1004 660
[ 22.558120] ueventd: fixup /sys/devices/virtual/input/input2/capsense_top/do_flush 1000 1004 660
[ 22.581400] ueventd: fixup /sys/devices/virtual/input/input3/enable 0 1004 660
[ 22.587930] ueventd: fixup /sys/devices/virtual/input/input3/poll_delay 0 1004 660
[ 22.595488] ueventd: fixup /sys/devices/virtual/input/input3/poll 1004 1000 660
[ 22.602730] ueventd: fixup /sys/devices/virtual/input/input3/pollrate_ms 1004 1000 660
[ 22.610723] ueventd: fixup /sys/devices/virtual/input/input3/enable_ps_sensor 1000 1004 660
[ 22.618993] ueventd: fixup /sys/devices/virtual/input/input3/set_delay_ms 1000 1004 660
[ 22.626983] ueventd: fixup /sys/devices/virtual/input/input3/do_flush 1000 1004 660
[ 22.665353] ueventd: fixup /sys/devices/virtual/input/input3/capsense_bottom/enable 0 1004 660
[ 22.673275] ueventd: fixup /sys/devices/virtual/input/input3/capsense_bottom/poll_delay 0 1004 660
[ 22.682282] ueventd: fixup /sys/devices/virtual/input/input3/capsense_bottom/poll 1004 1000 660
[ 22.690944] ueventd: fixup /sys/devices/virtual/input/input3/capsense_bottom/pollrate_ms 1004 1000 660
[ 22.700234] ueventd: fixup /sys/devices/virtual/input/input3/capsense_bottom/enable_ps_sensor 1000 1004 660
[ 22.709949] ueventd: fixup /sys/devices/virtual/input/input3/capsense_bottom/set_delay_ms 1000 1004 660
[ 22.719333] ueventd: fixup /sys/devices/virtual/input/input3/capsense_bottom/do_flush 1000 1004 660
[ 22.742774] ueventd: fixup /sys/devices/virtual/input/input3/event2/enable 0 1004 660
[ 22.749972] ueventd: fixup /sys/devices/virtual/input/input3/event2/poll_delay 0 1004 660
[ 22.758144] ueventd: fixup /sys/devices/virtual/input/input3/event2/poll 1004 1000 660
[ 22.766021] ueventd: fixup /sys/devices/virtual/input/input3/event2/pollrate_ms 1004 1000 660
[ 22.774594] ueventd: fixup /sys/devices/virtual/input/input3/event2/enable_ps_sensor 1000 1004 660
[ 22.783450] ueventd: fixup /sys/devices/virtual/input/input3/event2/set_delay_ms 1000 1004 660
[ 22.792067] ueventd: fixup /sys/devices/virtual/input/input3/event2/do_flush 1000 1004 660
[ 22.808838] ueventd: fixup /sys/devices/virtual/input/input4/enable 0 1004 660
[ 22.815923] ueventd: fixup /sys/devices/virtual/input/input4/poll_delay 0 1004 660
[ 22.822897] ueventd: fixup /sys/devices/virtual/input/input4/poll 1004 1000 660
[ 22.830199] ueventd: fixup /sys/devices/virtual/input/input4/pollrate_ms 1004 1000 660
[ 22.838152] ueventd: fixup /sys/devices/virtual/input/input4/enable_ps_sensor 1000 1004 660
[ 22.846437] ueventd: fixup /sys/devices/virtual/input/input4/set_delay_ms 1000 1004 660
[ 22.854425] ueventd: fixup /sys/devices/virtual/input/input4/do_flush 1000 1004 660
[ 22.879926] ueventd: fixup /sys/devices/virtual/input/input4/event3/enable 0 1004 660
[ 22.887103] ueventd: fixup /sys/devices/virtual/input/input4/event3/poll_delay 0 1004 660
[ 22.895281] ueventd: fixup /sys/devices/virtual/input/input4/event3/poll 1004 1000 660
[ 22.903146] ueventd: fixup /sys/devices/virtual/input/input4/event3/pollrate_ms 1004 1000 660
[ 22.911738] ueventd: fixup /sys/devices/virtual/input/input4/event3/enable_ps_sensor 1000 1004 660
[ 22.920616] ueventd: fixup /sys/devices/virtual/input/input4/event3/set_delay_ms 1000 1004 660
[ 22.929197] ueventd: fixup /sys/devices/virtual/input/input4/event3/do_flush 1000 1004 660
[ 22.945341] ueventd: fixup /sys/devices/virtual/input/input6/enable 0 1004 660
[ 22.951828] ueventd: fixup /sys/devices/virtual/input/input6/poll_delay 0 1004 660
[ 22.959411] ueventd: fixup /sys/devices/virtual/input/input6/poll 1004 1000 660
[ 22.966696] ueventd: fixup /sys/devices/virtual/input/input6/pollrate_ms 1004 1000 660
[ 22.974655] ueventd: fixup /sys/devices/virtual/input/input6/enable_ps_sensor 1000 1004 660
[ 22.982905] ueventd: fixup /sys/devices/virtual/input/input6/set_delay_ms 1000 1004 660
[ 22.990909] ueventd: fixup /sys/devices/virtual/input/input6/do_flush 1000 1004 660
[ 23.017002] ueventd: fixup /sys/devices/virtual/input/input6/event4/enable 0 1004 660
[ 23.024236] ueventd: fixup /sys/devices/virtual/input/input6/event4/poll_delay 0 1004 660
[ 23.032347] ueventd: fixup /sys/devices/virtual/input/input6/event4/poll 1004 1000 660
[ 23.040249] ueventd: fixup /sys/devices/virtual/input/input6/event4/pollrate_ms 1004 1000 660
[ 23.049304] ueventd: fixup /sys/devices/virtual/input/input6/event4/enable_ps_sensor 1000 1004 660
[ 23.057706] ueventd: fixup /sys/devices/virtual/input/input6/event4/set_delay_ms 1000 1004 660
[ 23.066296] ueventd: fixup /sys/devices/virtual/input/input6/event4/do_flush 1000 1004 660
[ 23.352820] ueventd: fixup /sys/devices/virtual/smdpkt/smdcntl0/open_timeout 1001 1001 664
[ 23.364137] ueventd: fixup /sys/devices/virtual/smdpkt/smdcntl8/open_timeout 1001 1001 664
[ 23.448422] ueventd: Coldboot took 5.66394 seconds
[ 23.458623] init: Command 'wait_for_coldboot_done' action=wait_for_coldboot_done returned 0 took 5293.57ms.
[ 23.468600] init: processing action (mix_hwrng_into_linux_rng)
[ 23.479125] init: Mixed 512 bytes from /dev/hw_random into /dev/urandom
[ 23.484876] init: processing action (set_mmap_rnd_bits)
[ 23.490607] init: processing action (set_kptr_restrict)
[ 23.495913] init: processing action (keychord_init)
[ 23.500065] init: processing action (console_init)
[ 23.504929] init: processing action (init)
[ 23.530686] init: write_file: Unable to open '/proc/sys/kernel/hung_task_timeout_secs': No such file or directory
[ 23.556834] init: write_file: Unable to open '/proc/sys/abi/swp': No such file or directory
[ 23.564649] init: write_file: Unable to open '/sys/class/leds/vibrator/trigger': No such file or directory
[ 23.575425] init: write_file: Unable to open '/sys/fs/cgroup/memory/bg/memory.swappiness': No such file or directory
[ 23.585084] init: write_file: Unable to open '/sys/fs/cgroup/memory/bg/memory.move_charge_at_immigrate': No such file or directory
[ 23.597210] init: processing action (mix_hwrng_into_linux_rng)
[ 23.607776] init: Mixed 512 bytes from /dev/hw_random into /dev/urandom
[ 23.613500] init: processing action (late-init)
[ 23.618060] init: processing action (queue_property_triggers)
[ 23.623716] init: processing action (fs)
[ 23.690186] init: [libfs_mgr]Invalid ext4 magic:0xadcb,/dev/block/bootdevice/by-name/userdata
[ 23.697958] init: [libfs_mgr]mount_with_alternatives(): skipping mount, invalid ext4, mountpoint=/data rec[0].fs_type=ext4
[ 23.709756] init: [libfs_mgr]fs_mgr_mount_all(): possibly an encryptable blkdev /dev/block/bootdevice/by-name/userdata for mount /data type ext4
[ 23.723621] init: [libfs_mgr]superblock s_max_mnt_count:10,/dev/block/bootdevice/by-name/cache
[ 23.731299] init: [libfs_mgr]Requested quota status is match on /dev/block/bootdevice/by-name/cache
[ 23.746670] EXT4-fs (mmcblk0p53): mounted filesystem with ordered data mode. Opts: barrier=1
[ 23.754464] init: [libfs_mgr]__mount(source=/dev/block/bootdevice/by-name/cache,target=/cache,type=ext4)=0
[ 23.776289] init: [libfs_mgr]__mount(source=/dev/block/bootdevice/by-name/modem,target=/firmware,type=vfat)=0
[ 23.786341] init: [libfs_mgr]superblock s_max_mnt_count:65535,/dev/block/bootdevice/by-name/dsp
[ 23.794109] init: [libfs_mgr]Requested quota status is match on /dev/block/bootdevice/by-name/dsp
[ 23.811682] EXT4-fs (mmcblk0p22): mounted filesystem with ordered data mode. Opts: barrier=1
[ 23.819378] init: [libfs_mgr]__mount(source=/dev/block/bootdevice/by-name/dsp,target=/dsp,type=ext4)=0
[ 23.830604] init (386) used greatest stack depth: 4756 bytes left
[ 23.830855] init: Parsing file /odm/etc/init...
[ 23.831061] init: Command 'mount_all /vendor/etc/fstab.qcom' action=fs (/vendor/etc/init/hw/init.target.rc:41) returned 2 took 203.292ms.
[ 23.856045] EXT4-fs (mmcblk0p30): warning: maximal mount count reached, running e2fsck is recommended
[ 23.866300] EXT4-fs (mmcblk0p30): mounted filesystem with ordered data mode. Opts: barrier=1
[ 23.877532] selinux: SELinux: Skipping restorecon_recursive(/persist)
[ 23.877532]
[ 23.885728] EXT4-fs (mmcblk0p51): VFS: Can't find ext4 filesystem
[ 23.892173] init: processing action (post-fs)
[ 23.903862] init: Couldn't load properties from /vendor/package/Default/system/vendor/vendor.prop: No such file or directory
[ 23.915737] init: property_set("ro.cutoff_voltage_mv", "3400") failed: property already set
[ 23.923303] init: Couldn't load properties from /vendor/package/vendor.prop: No such file or directory
[ 23.936379] init: Couldn't load properties from /system/vendor/vendor.prop: No such file or directory
[ 23.945502] init: Couldn't load properties from /vendor/package/Default/system/vendor/vendor.prop: No such file or directory
[ 23.956803] init: property_set("ro.telephony.default_network", "22,20") failed: property already set
[ 23.965151] init: Couldn't load properties from /vendor/package/power.prop: No such file or directory
[ 23.974269] init: Couldn't load properties from /odm/build.prop: No such file or directory
[ 23.984192] init: Couldn't load properties from /factory/factory.prop: No such file or directory
[ 23.995959] init: /recovery not specified in fstab
[ 23.999795] init: Command 'load_system_props' action=post-fs (/init.rc:298) returned 0 took 104.164ms.
[ 24.009385] init: computing context for service 'logd'
[ 24.017772] init: starting service 'logd'...
[ 24.025485] init: computing context for service 'servicemanager'
[ 24.026358] init: Created socket '/dev/socket/logd', mode 666, user 1036, group 1036
[ 24.028391] init: Created socket '/dev/socket/logdr', mode 666, user 1036, group 1036
[ 24.030248] init: Created socket '/dev/socket/logdw', mode 222, user 1036, group 1036
[ 24.030605] init: Opened file '/proc/kmsg', flags 0
[ 24.030737] init: Opened file '/dev/kmsg', flags 1
[ 24.064335] init: starting service 'servicemanager'...
[ 24.072791] init: computing context for service 'hwservicemanager'
[ 24.078656] init: starting service 'hwservicemanager'...
[ 24.114338] init: computing context for service 'vndservicemanager'
[ 24.120345] init: starting service 'vndservicemanager'...
[ 24.204755] logd.auditd: start
[ 24.206920] logd.klogd: 24192885875
[ 24.246445] binder: 397:397 ioctl 620a ce3738b5 returned -22
[ 24.467044] init: Command 'restorecon --recursive --cross-filesystems /sys/kernel/debug' action=post-fs (/init.rc:315) returned 0 took 333.256ms.
[ 24.482609] selinux: SELinux: Skipping restorecon_recursive(/cache)
[ 24.482609]
[ 24.508151] init: write_file: Unable to open '/sys/kernel/tracing/tracing_on': Permission denied
[ 24.519733] init: processing action (late-fs)
[ 24.524342] init: computing context for service 'gatekeeper-1-0'
[ 24.530086] init: starting service 'gatekeeper-1-0'...
[ 24.538158] init: computing context for service 'keymaster-3-0'
[ 24.543732] init: starting service 'keymaster-3-0'...
[ 24.551774] init: processing action (post-fs-data)
[ 24.557108] init: computing context for service 'vold'
[ 24.562082] init: starting service 'vold'...
[ 24.571513] init: Created socket '/dev/socket/vold', mode 660, user 0, group 1009
[ 24.580113] init: Created socket '/dev/socket/cryptd', mode 660, user 0, group 1009
[ 24.771646] vdc: 200 410 Command succeeded
[ 24.775514] init: init_user0 result: 0
[ 24.778519] init: Command 'init_user0' action=post-fs-data (/init.rc:489) returned 0 took 139.798ms.
[ 24.822109] init: computing context for service 'exec 1 (/system/bin/tzdatacheck)'
[ 24.829569] init: starting service 'exec 1 (/system/bin/tzdatacheck)'...
[ 24.839226] init: SVC_EXEC pid 414 (uid 1000 gid 1000+0 context default) started; waiting...
[ 24.893599] init: Service 'exec 1 (/system/bin/tzdatacheck)' (pid 414) exited with status 0 waiting took 0.071840 seconds
[ 24.962591] init: write_file: Unable to open '/sys/block/dm-0/queue/read_ahead_kb': No such file or directory
[ 24.971739] init: write_file: Unable to open '/sys/block/dm-1/queue/read_ahead_kb': No such file or directory
[ 24.992009] init: computing context for service 'carrier_switcher'
[ 24.997845] init: service carrier_switcher does not have a SELinux domain defined
[ 25.009900] init: processing action (load_persist_props_action)
[ 25.014987] init: Couldn't load properties from /data/local.prop: No such file or directory
[ 25.023428] init: computing context for service 'logd-reinit'
[ 25.029520] init: starting service 'logd-reinit'...
[ 25.037338] init: processing action (firmware_mounts_complete)
[ 25.042326] init: processing action (early-boot)
[ 25.047133] adsp-loader soc:qcom,msm-adsp-loader: adsp_loader_do: scheduling work to load ADSP fw
[ 25.057735] init: write_file: Unable to open '/sys/kernel/boot_cdsp/boot': No such file or directory
[ 25.066185] sensors-ssc soc:qcom,msm-ssc-sensors: slpi_loader_do: scheduling work to load SLPI fw
[ 25.075140] sensors-ssc soc:qcom,msm-ssc-sensors: slpi_load_fw: pil get failed,
[ 25.077410] logd.daemon: reinit
[ 25.077520] init: starting service 'exec 2 (/vendor/bin/init.qcom.early_boot.sh)'...
[ 25.081014] init: SVC_EXEC pid 417 (uid 0 gid 0+0 context u:r:qti_init_shell:s0) started; waiting...
[ 25.081411] init: Service 'logd-reinit' (pid 415) exited with status 0
[ 25.108526] sensors-ssc soc:qcom,msm-ssc-sensors: slpi_load_fw: SLPI image loading failed
[ 25.290963] ueventd: firmware: loading 'adsp.mdt' for '/devices/soc/c200000.qcom,lpass/firmware/adsp.mdt'
[ 25.307463] ueventd: loading /devices/soc/c200000.qcom,lpass/firmware/adsp.mdt took 0.0169157 seconds
[ 25.307841] subsys-pil-tz c200000.qcom,lpass: adsp: loading from 0x8b800000 to 0x8c900000
[ 25.342296] ueventd: firmware: loading 'adsp.b02' for '/devices/soc/c200000.qcom,lpass/firmware/adsp.b02'
[ 25.353297] ueventd: loading /devices/soc/c200000.qcom,lpass/firmware/adsp.b02 took 0.0114283 seconds
[ 25.359465] ueventd: firmware: loading 'adsp.b03' for '/devices/soc/c200000.qcom,lpass/firmware/adsp.b03'
[ 25.388169] ueventd: loading /devices/soc/c200000.qcom,lpass/firmware/adsp.b03 took 0.0291197 seconds
[ 25.393943] ueventd: firmware: loading 'adsp.b04' for '/devices/soc/c200000.qcom,lpass/firmware/adsp.b04'
[ 25.584953] init: Service 'exec 2 (/vendor/bin/init.qcom.early_boot.sh)' (pid 417) exited with status 0 waiting took 0.509901 seconds
[ 25.609341] ueventd: loading /devices/soc/c200000.qcom,lpass/firmware/adsp.b04 took 0.215772 seconds
[ 25.615301] ueventd: firmware: loading 'adsp.b05' for '/devices/soc/c200000.qcom,lpass/firmware/adsp.b05'
[ 25.624388] init: processing action (boot)
[ 25.639654] init: computing context for service 'hidl_memory'
[ 25.645125] init: starting service 'hidl_memory'...
[ 25.653253] init: computing context for service 'audio-hal-2-0'
[ 25.655918] ueventd: loading /devices/soc/c200000.qcom,lpass/firmware/adsp.b05 took 0.0410712 seconds
[ 25.665453] ueventd: firmware: loading 'adsp.b06' for '/devices/soc/c200000.qcom,lpass/firmware/adsp.b06'
[ 25.677922] init: starting service 'audio-hal-2-0'...
[ 25.677947] ueventd: loading /devices/soc/c200000.qcom,lpass/firmware/adsp.b06 took 0.0129849 seconds
[ 25.683741] ueventd: firmware: loading 'adsp.b07' for '/devices/soc/c200000.qcom,lpass/firmware/adsp.b07'
[ 25.693593] ueventd: loading /devices/soc/c200000.qcom,lpass/firmware/adsp.b07 took 0.0103208 seconds
[ 25.699095] ueventd: firmware: loading 'adsp.b08' for '/devices/soc/c200000.qcom,lpass/firmware/adsp.b08'
[ 25.712914] ueventd: loading /devices/soc/c200000.qcom,lpass/firmware/adsp.b08 took 0.0142079 seconds
[ 25.718274] ueventd: firmware: loading 'adsp.b09' for '/devices/soc/c200000.qcom,lpass/firmware/adsp.b09'
[ 25.730283] ueventd: loading /devices/soc/c200000.qcom,lpass/firmware/adsp.b09 took 0.0124309 seconds
[ 25.735902] ueventd: firmware: loading 'adsp.b10' for '/devices/soc/c200000.qcom,lpass/firmware/adsp.b10'
[ 25.761666] init: computing context for service 'bluetooth-1-0'
[ 25.767528] init: starting service 'bluetooth-1-0'...
[ 25.776369] init: computing context for service 'camera-provider-2-4'
[ 25.782874] init: starting service 'camera-provider-2-4'...
[ 25.788183] ueventd: loading /devices/soc/c200000.qcom,lpass/firmware/adsp.b10 took 0.0527235 seconds
[ 25.790446] init: couldn't write 481 to /dev/cpuset/camera-daemon/tasks: No such file or directory
[ 25.792825] init: computing context for service 'configstore-hal-1-0'
[ 25.793610] init: starting service 'configstore-hal-1-0'...
[ 25.795062] ueventd: firmware: loading 'adsp.b11' for '/devices/soc/c200000.qcom,lpass/firmware/adsp.b11'
[ 25.797482] init: computing context for service 'drm-hal-1-0'
[ 25.798235] init: starting service 'drm-hal-1-0'...
[ 25.802938] init: computing context for service 'gralloc-2-0'
[ 25.803808] init: starting service 'gralloc-2-0'...
[ 25.807578] ueventd: loading /devices/soc/c200000.qcom,lpass/firmware/adsp.b11 took 0.0130007 seconds
[ 25.808012] init: computing context for service 'hwcomposer-2-1'
[ 25.809194] init: starting service 'hwcomposer-2-1'...
[ 25.815507] init: computing context for service 'health-hal-1-0'
[ 25.816950] init: starting service 'health-hal-1-0'...
[ 25.821832] ueventd: firmware: loading 'adsp.b12' for '/devices/soc/c200000.qcom,lpass/firmware/adsp.b12'
[ 25.822699] init: computing context for service 'light-hal-2-0'
[ 25.823596] init: starting service 'light-hal-2-0'...
[ 25.828745] init: computing context for service 'memtrack-hal-1-0'
[ 25.829740] init: starting service 'memtrack-hal-1-0'...
[ 25.830071] ueventd: loading /devices/soc/c200000.qcom,lpass/firmware/adsp.b12 took 0.00873729 seconds
[ 25.835262] init: computing context for service 'power-hal-1-0'
[ 25.836300] init: starting service 'power-hal-1-0'...
[ 25.837354] ueventd: firmware: loading 'adsp.b13' for '/devices/soc/c200000.qcom,lpass/firmware/adsp.b13'
[ 25.841293] init: computing context for service 'sensors-hal-1-0'
[ 25.842133] init: starting service 'sensors-hal-1-0'...
[ 25.847360] init: computing context for service 'usb-hal-1-0'
[ 25.848228] init: starting service 'usb-hal-1-0'...
[ 25.853937] init: computing context for service 'vibrator-1-0'
[ 25.854953] init: starting service 'vibrator-1-0'...
[ 25.858788] ueventd: loading /devices/soc/c200000.qcom,lpass/firmware/adsp.b13 took 0.0219166 seconds
[ 25.862252] init: computing context for service 'wifi_hal_legacy'
[ 25.863082] init: starting service 'wifi_hal_legacy'...
[ 25.875182] init: computing context for service 'display-color-hal-1-0'
[ 25.876238] init: starting service 'display-color-hal-1-0'...
[ 25.906878] init: computing context for service 'qti_esepowermanager_service'
[ 25.907758] init: starting service 'qti_esepowermanager_service'...
[ 25.912587] init: computing context for service 'alarm-hal-1-0'
[ 25.913478] init: starting service 'alarm-hal-1-0'...
[ 25.960916] init: computing context for service 'iop-hal-1-0'
[ 25.962009] init: starting service 'iop-hal-1-0'...
[ 25.980395] init: computing context for service 'perf-hal-1-0'
[ 25.981288] init: starting service 'perf-hal-1-0'...
[ 26.018625] init: computing context for service 'qteeconnector-hal-1-0'
[ 26.019938] init: starting service 'qteeconnector-hal-1-0'...
[ 26.060304] init: Command 'class_start hal' action=boot (/init.rc:631) returned 0 took 421.786ms.
[ 26.060936] init: computing context for service 'healthd'
[ 26.062180] init: starting service 'healthd'...
[ 26.067107] init: computing context for service 'qcom-c_core-sh'
[ 26.067918] init: starting service 'qcom-c_core-sh'...
[ 26.072421] init: computing context for service 'irsc_util'
[ 26.093014] init: starting service 'irsc_util'...
[ 26.109126] init: computing context for service 'rmt_storage'
[ 26.130675] init: starting service 'rmt_storage'...
[ 26.170698] subsys-pil-tz c200000.qcom,lpass: adsp: Brought out of reset
[ 26.176772] init: computing context for service 'tftp_server'
[ 26.183604] init: starting service 'tftp_server'...
[ 26.188104] subsys-pil-tz c200000.qcom,lpass: Subsystem error monitoring/handling services are up
[ 26.188110] subsys-pil-tz c200000.qcom,lpass: adsp: Power/Clock ready interrupt received
[ 26.188270] L-Notify: Generel: 7
[ 26.207676] mitigate_inrush_notifier_cb: subsystem adsp has completed powerup
[ 26.216334] init: computing context for service 'sensor-sh'
[ 26.223081] init: starting service 'sensor-sh'...
[ 26.233315] diag: In diag_send_feature_mask_update, control channel is not open, p: 1, c190cc24
[ 26.241239] apr_tal:Q6 Is Up
[ 26.241768] init: cannot find '/system/vendor/bin/esepmdaemon', disabling 'esepmdaemon': No such file or directory
[ 26.242288] init: computing context for service 'qseecomd'
[ 26.245802] init: starting service 'qseecomd'...
[ 26.257492] init: computing context for service 'per_mgr'
[ 26.258371] init: starting service 'per_mgr'...
[ 26.262081] init: starting service 'cs-early-boot'...
[ 26.282005] init: computing context for service 'lmkd'
[ 26.283452] type=1400 audit(423455.379:7): avc: denied { read write } for pid=493 comm="android.hardwar" name="wake_lock" dev="sysfs" ino=90 scontext=u:r:hal_sensors_default:s0 tcontext=u:object_r:sysfs_wake_lock:s0 tclass=file permissive=0
[ 26.296060] kgsl-3d 1c00000.qcom,kgsl-3d0: dev_pm_opp_get_opp_count: device OPP not found (-19)
[ 26.296571] devbw soc:qcom,gpubw: dev_pm_opp_get_opp_count: device OPP not found (-19)
[ 26.315281] devbw soc:qcom,cpubw: dev_pm_opp_get_opp_count: device OPP not found (-19)
[ 26.335208] init: starting service 'lmkd'...
[ 26.335703] type=1400 audit(423455.379:7): avc: denied { read write } for pid=493 comm="android.hardwar" name="wake_lock" dev="sysfs" ino=90 scontext=u:r:hal_sensors_default:s0 tcontext=u:object_r:sysfs_wake_lock:s0 tclass=file permissive=0
[ 26.335757] type=1400 audit(423455.459:8): avc: denied { read } for pid=541 comm="getprop" name="u:object_r:coresight_prop:s0" dev="tmpfs" ino=91 scontext=u:r:vendor-qti-testscripts:s0 tcontext=u:object_r:coresight_prop:s0 tclass=file permissive=1
[ 26.337693] type=1400 audit(423455.459:8): avc: denied { read } for pid=541 comm="getprop" name="u:object_r:coresight_prop:s0" dev="tmpfs" ino=91 scontext=u:r:vendor-qti-testscripts:s0 tcontext=u:object_r:coresight_prop:s0 tclass=file permissive=1
[ 26.337739] type=1400 audit(423455.459:9): avc: denied { open } for pid=541 comm="getprop" path="/dev/__properties__/u:object_r:coresight_prop:s0" dev="tmpfs" ino=91 scontext=u:r:vendor-qti-testscripts:s0 tcontext=u:object_r:coresight_prop:s0 tclass=file permissive=1
[ 26.339336] type=1400 audit(423455.459:9): avc: denied { open } for pid=541 comm="getprop" path="/dev/__properties__/u:object_r:coresight_prop:s0" dev="tmpfs" ino=91 scontext=u:r:vendor-qti-testscripts:s0 tcontext=u:object_r:coresight_prop:s0 tclass=file permissive=1
[ 26.339382] type=1400 audit(423455.459:10): avc: denied { getattr } for pid=541 comm="getprop" path="/dev/__properties__/u:object_r:coresight_prop:s0" dev="tmpfs" ino=91 scontext=u:r:vendor-qti-testscripts:s0 tcontext=u:object_r:coresight_prop:s0 tclass=file permissive=1
[ 26.357068] sysmon-qmi: sysmon_clnt_svc_arrive: Connection established between QMI handle and adsp's SSCTL service
[ 26.374168] rmt_storage:INFO:main: Done with init now waiting for messages!
[ 26.391683] msm8952-asoc-wcd c051000.sound: default codec configured
[ 26.400850] msm8952-asoc-wcd c051000.sound: ASoC: platform (null) not registered
[ 26.400923] msm8952-asoc-wcd c051000.sound: snd_soc_register_card failed (-517)
[ 26.401048] type=1400 audit(423455.459:10): avc: denied { getattr } for pid=541 comm="getprop" path="/dev/__properties__/u:object_r:coresight_prop:s0" dev="tmpfs" ino=91 scontext=u:r:vendor-qti-testscripts:s0 tcontext=u:object_r:coresight_prop:s0 tclass=file permissive=1
[ 26.401091] type=1400 audit(423455.479:11): avc: denied { write } for pid=548 comm="mkdir" name="sensors" dev="mmcblk0p30" ino=18 scontext=u:r:qti_init_shell:s0 tcontext=u:object_r:sensors_persist_file:s0 tclass=dir permissive=0
[ 26.404848] type=1400 audit(423455.479:11): avc: denied { write } for pid=548 comm="mkdir" name="sensors" dev="mmcblk0p30" ino=18 scontext=u:r:qti_init_shell:s0 tcontext=u:object_r:sensors_persist_file:s0 tclass=dir permissive=0
[ 26.404881] type=1400 audit(423455.499:12): avc: denied { write } for pid=515 comm="rmt_storage" name="rmts" dev="debugfs" ino=12210 scontext=u:r:rmt_storage:s0 tcontext=u:object_r:debugfs:s0 tclass=file permissive=0
[ 26.405056] type=1400 audit(423455.499:12): avc: denied { write } for pid=515 comm="rmt_storage" name="rmts" dev="debugfs" ino=12210 scontext=u:r:rmt_storage:s0 tcontext=u:object_r:debugfs:s0 tclass=file permissive=0
[ 26.405104] type=1400 audit(423455.529:13): avc: denied { write } for pid=488 comm="[email protected]" name="kmsg" dev="tmpfs" ino=13330 scontext=u:r:hal_health_default:s0 tcontext=u:object_r:kmsg_device:s0 tclass=chr_file permissive=0
[ 26.420486] healthd: Unknown power supply type 'BMS'
[ 26.421227] healthd: Unknown power supply type 'BMS'
[ 26.424297] healthd: Unknown power supply type 'BMS'
[ 26.431257] ueventd: firmware: loading 'a530_pm4.fw' for '/devices/soc/1c00000.qcom,kgsl-3d0/kgsl/kgsl-3d0/a530_pm4.fw'
[ 26.433842] healthd: BatteryCycleCountPath not found
[ 26.442768] ueventd: loading /devices/soc/1c00000.qcom,kgsl-3d0/kgsl/kgsl-3d0/a530_pm4.fw took 0.0138294 seconds
[ 26.460078] ueventd: firmware: loading 'a530_pfp.fw' for '/devices/soc/1c00000.qcom,kgsl-3d0/kgsl/kgsl-3d0/a530_pfp.fw'
[ 26.464422] ueventd: loading /devices/soc/1c00000.qcom,kgsl-3d0/kgsl/kgsl-3d0/a530_pfp.fw took 0.00469016 seconds
[ 26.465370] msm8952-asoc-wcd c051000.sound: default codec configured
[ 26.477685] devfreq soc:qcom,kgsl-busmon: Couldn't update frequency transition information.
[ 26.490590] wcd-spmi-core msm8x16_wcd_codec-1: Error: regulator not found:cdc-vdd-spkdrv
[ 26.529340] msm-pcm-routing soc:qcom,msm-pcm-routing: ASoC: no dapm match for MM_DL5 --> MultiMedia5 --> TERT_MI2S_RX Audio Mixer
[ 26.529347] msm-pcm-routing soc:qcom,msm-pcm-routing: ASoC: Failed to add route MM_DL5 -> MultiMedia5 -> TERT_MI2S_RX Audio Mixer
[ 26.529453] msm-pcm-routing soc:qcom,msm-pcm-routing: ASoC: no dapm match for MM_DL8 --> MultiMedia8 --> TERT_MI2S_RX Audio Mixer
[ 26.529459] msm-pcm-routing soc:qcom,msm-pcm-routing: ASoC: Failed to add route MM_DL8 -> MultiMedia8 -> TERT_MI2S_RX Audio Mixer
[ 26.530559] msm-pcm-routing soc:qcom,msm-pcm-routing: ASoC: no dapm match for INT_FM_TX --> INTERNAL_FM_TX --> SEC_MI2S_RX Port Mixer
[ 26.530564] msm-pcm-routing soc:qcom,msm-pcm-routing: ASoC: Failed to add route INT_FM_TX -> INTERNAL_FM_TX -> SEC_MI2S_RX Port Mixer
[ 26.531575] capability: warning: `qseecomd' uses 32-bit capabilities (legacy support in use)
[ 26.558839] scm_call failed: func id 0x32000206, ret: -1, syscall returns: 0x0, 0x0, 0x0
[ 26.561086] scm_call failed: func id 0x32000206, ret: -1, syscall returns: 0x0, 0x0, 0x0
[ 26.563016] scm_call failed: func id 0x32000206, ret: -1, syscall returns: 0x0, 0x0, 0x0
[ 26.566449] msm-pcm-routing soc:qcom,msm-pcm-routing: ASoC: no source widget found for AUDIO_REF_EC_UL3 MUX
[ 26.566455] msm-pcm-routing soc:qcom,msm-pcm-routing: ASoC: Failed to add route AUDIO_REF_EC_UL3 MUX -> direct -> MM_UL3
[ 26.583462] scm_call failed: func id 0x32000206, ret: -1, syscall returns: 0x0, 0x0, 0x0
[ 26.584820] msm-pcm-routing soc:qcom,msm-pcm-routing: ASoC: no dapm match for SEC_MI2S_TX --> SEC_MI2S_TX --> SLIMBUS_0_RX Port Mixer
[ 26.584826] msm-pcm-routing soc:qcom,msm-pcm-routing: ASoC: Failed to add route SEC_MI2S_TX -> SEC_MI2S_TX -> SLIMBUS_0_RX Port Mixer
[ 26.587119] msm-pcm-routing soc:qcom,msm-pcm-routing: ASoC: no dapm match for VOICE2_STUB_DL --> Voice2 Stub --> INTERNAL_BT_SCO_RX_Voice Mixer
[ 26.587124] msm-pcm-routing soc:qcom,msm-pcm-routing: ASoC: Failed to add route VOICE2_STUB_DL -> Voice2 Stub -> INTERNAL_BT_SCO_RX_Voice Mixer
[ 26.588580] scm_call failed: func id 0x32000206, ret: -1, syscall returns: 0x0, 0x0, 0x0
[ 26.591478] msm-pcm-routing soc:qcom,msm-pcm-routing: ASoC: no sink widget found for SENARY_MI2S_TX
[ 26.591483] msm-pcm-routing soc:qcom,msm-pcm-routing: ASoC: Failed to add route BE_IN -> direct -> SENARY_MI2S_TX
[ 26.595693] scm_call failed: func id 0x32000206, ret: -1, syscall returns: 0x0, 0x0, 0x0
[ 26.602908] scm_call failed: func id 0x32000206, ret: -1, syscall returns: 0x0, 0x0, 0x0
[ 26.609000] scm_call failed: func id 0x32000206, ret: -1, syscall returns: 0x0, 0x0, 0x0
[ 26.824746] msm-pcm-routing soc:qcom,msm-pcm-routing: ASoC: Failed to create SEC_MI2S_RX Port Mixer debugfs file
[ 26.859618] msm-pcm-routing soc:qcom,msm-pcm-routing: ASoC: mux SLIM_0_RX AANC MUX has no paths
[ 26.889691] wcd-spmi-core msm8x16_wcd_codec-1: ASoC: mux RX3 MIX1 INP3 has no paths
[ 26.890493] wcd-spmi-core msm8x16_wcd_codec-1: ASoC: mux RX2 MIX1 INP3 has no paths
[ 26.992526] init: computing context for service 'surfaceflinger'
[ 26.994713] init: Created socket '/dev/socket/lmkd', mode 660, user 1000, group 1000
[ 27.006603] init: starting service 'surfaceflinger'...
[ 27.015258] init: Command 'class_start core' action=boot (/init.rc:633) returned 0 took 954.7ms.
[ 27.016050] init: Failed to bind socket 'pdx/system/vr/display/client': No such file or directory
[ 27.017764] init: Failed to bind socket 'pdx/system/vr/display/manager': No such file or directory
[ 27.019440] init: Failed to bind socket 'pdx/system/vr/display/vsync': No such file or directory
[ 27.051290] init: Service 'irsc_util' (pid 512) exited with status 0
[ 27.058775] init: starting service 'console'...
[ 27.065599] init: setpgid failed for console: Operation not permitted
[ 27.069155] init: computing context for service 'sensors'
[ 27.069883] init: starting service 'sensors'...
[ 27.082877] init: Service 'qcom-c_core-sh' (pid 511) exited with status 0
[ 27.089065] init: Service 'sensor-sh' (pid 526) exited with status 0
[ 27.104206] type=1400 audit(423455.529:13): avc: denied { write } for pid=488 comm="[email protected]" name="kmsg" dev="tmpfs" ino=13330 scontext=u:r:hal_health_default:s0 tcontext=u:object_r:kmsg_device:s0 tclass=chr_file permissive=0
[ 27.115550] msm8952-asoc-wcd c051000.sound: ASoC: no sink widget found for SpkrMono WSA_IN
[ 27.115556] msm8952-asoc-wcd c051000.sound: ASoC: Failed to add route WSA_SPK OUT -> direct -> SpkrMono WSA_IN
[ 27.124609] init: insmod: open("/vendor/lib/modules/msm_11ad_proxy.ko") failed: No such file or directory
[ 27.128802] init: write_file: Unable to open '/config/usb_gadget/g1/bcdUSB': No such file or directory
[ 27.128992] init: write_file: Unable to open '/config/usb_gadget/g1/os_desc/use': No such file or directory
[ 27.129194] init: write_file: Unable to open '/config/usb_gadget/g1/strings/0x409/serialnumber': No such file or directory
[ 27.129359] init: write_file: Unable to open '/config/usb_gadget/g1/strings/0x409/manufacturer': No such file or directory
[ 27.129569] init: write_file: Unable to open '/config/usb_gadget/g1/strings/0x409/product': No such file or directory
[ 27.140068] init: write_file: Unable to open '/config/usb_gadget/g1/os_desc/b_vendor_code': No such file or directory
[ 27.140231] init: write_file: Unable to open '/config/usb_gadget/g1/os_desc/qw_sign': No such file or directory
[ 27.148770] init: insmod: open("/system/lib/modules/adsprpc.ko") failed: No such file or directory
[ 27.152076] init: write_file: Unable to open '/sys/devices/soc.0/78b8000.i2c/i2c-4/4-0020/input/input0/fw_name': No such file or directory
[ 27.152234] init: write_file: Unable to open '/sys/devices/soc.0/78b8000.i2c/i2c-4/4-0020/input/input0/update_fw': No such file or directory
[ 27.154768] enable_store: android_usb: already disabled
[ 27.263299] type=1400 audit(423456.239:14): avc: denied { net_raw } for pid=528 comm="pm-service" capability=13 scontext=u:r:per_mgr:s0 tcontext=u:r:per_mgr:s0 tclass=capability permissive=0
[ 27.283307] ipa_get_ipc_logbuf_low:2736 IPA HW is not supported
aljeter:/ $ [ 27.416506] msm_otg 78db000.usb: ep_dequeue: Unable to dequeue while in LPM
[ 27.468089] ipa_get_ipc_logbuf_low:2736 IPA HW is not supported
[ 27.497685] ueventd: firmware: could not find firmware for msadp
[ 27.503750] pil-q6v5-mss 4080000.qcom,mss: Debug policy not present - msadp. Continue.
[ 27.937049] msm_qti_pp_get_rms_value_control, back not active to query rms be_idx:3
[ 27.950200] msm_dolby_dap_param_to_get_control_get, port_id not set, do not query ADM
[ 27.957395] msm_dolby_dap_param_visualizer_control_get Incorrect VCNB length
[ 27.964691] msm_voice_sound_focus_get: Error getting Sound Focus Params, err=-22
[ 27.971643] msm_voice_source_tracking_get: Error getting Source Tracking Params, err=-22
[ 27.979867] msm_audio_get_copp_idx_from_port_id: Invalid FE, exiting
[ 27.985850] msm_audio_sound_focus_get: Could not get copp idx for port_id=16385
[ 27.993420] msm_audio_get_copp_idx_from_port_id: Invalid FE, exiting
[ 27.999579] msm_audio_source_tracking_get: Could not get copp idx for port_id=16385
[ 28.007477] msm_voice_sound_focus_get: Error getting Sound Focus Params, err=-22
[ 28.014908] msm_voice_source_tracking_get: Error getting Source Tracking Params, err=-22
[ 28.022872] msm_audio_get_copp_idx_from_port_id: Invalid FE, exiting
[ 28.028923] msm_audio_sound_focus_get: Could not get copp idx for port_id=4101
[ 28.036490] msm_audio_get_copp_idx_from_port_id: Invalid FE, exiting
[ 28.042404] msm_audio_source_tracking_get: Could not get copp idx for port_id=4101
[ 28.050390] msm_audio_get_copp_idx_from_port_id: Invalid FE, exiting
[ 28.056786] msm_audio_sound_focus_get: Could not get copp idx for port_id=4103
[ 28.063851] msm_audio_get_copp_idx_from_port_id: Invalid FE, exiting
[ 28.069894] msm_audio_source_tracking_get: Could not get copp idx for port_id=4103
[ 28.080094] msm_pcm_volume_ctl_get substream runtime not found
[ 28.086145] msm_pcm_volume_ctl_get substream runtime not found
[ 28.091959] msm_pcm_volume_ctl_get substream runtime not found
[ 28.097462] msm_compr_audio_effects_config_get: stream or effects inactive
[ 28.105287] msm_pcm_volume_ctl_get substream runtime not found
[ 28.111190] msm_pcm_volume_ctl_get substream runtime not found
[ 28.116384] msm_pcm_volume_ctl_get substream or runtime not found
[ 28.123647] msm_compr_audio_effects_config_get: stream or effects inactive
[ 28.130967] msm_compr_audio_effects_config_get: stream or effects inactive
[ 28.138079] msm_compr_audio_effects_config_get: stream or effects inactive
[ 28.145270] msm_compr_audio_effects_config_get: stream or effects inactive
[ 28.152322] msm_compr_audio_effects_config_get: stream or effects inactive
[ 28.159715] msm_compr_audio_effects_config_get: stream or effects inactive
[ 28.167115] msm_compr_audio_effects_config_get: stream or effects inactive
[ 28.174398] msm_compr_audio_effects_config_get: stream or effects inactive
[ 28.181464] msm_pcm_volume_ctl_get substream or runtime not found
[ 28.187682] msm_compr_audio_effects_config_get: stream or effects inactive
[ 28.195077] msm_compr_audio_effects_config_get: stream or effects inactive
[ 28.202253] msm_compr_audio_effects_config_get: stream or effects inactive
[ 29.019011] QSEECOM: __qseecom_process_incomplete_cmd: fail:resp res= -65,app_id = 0,lstr = 12288
[ 29.245484] QSEECOM: qseecom_create_key: Set the key successfully
[ 29.373217] ipa_get_ipc_logbuf_low:2736 IPA HW is not supported
[ 29.375230] M-Notify: General: 7
[ 29.375235] ipa_get_ipc_logbuf_low:2736 IPA HW is not supported
[ 29.484253] rmt_storage:INFO:rmt_storage_open_cb: Processing: Open Request for /boot/modem_fs1!
[ 29.494873] rmt_storage:INFO:rmt_storage_open_cb: Processing: Open Request for /boot/modem_fs2!
[ 29.505192] rmt_storage:INFO:rmt_storage_open_cb: Processing: Open Request for /boot/modem_fsg!
[ 29.515967] rmt_storage:INFO:rmt_storage_open_cb: Processing: Open Request for /boot/modem_fsc!
[ 29.528983] rmt_storage:INFO:rmt_storage_alloc_buff_cb: Received req_size: 0! avail: 1572864
[ 29.538683] rmt_storage:INFO:rmt_storage_rw_iovec_cb: Read iovec request received for /boot/modem_fs1
[ 29.547291] rmt_storage:INFO:rmt_storage_client_thread: Calling Read [offset=512, size=512]for /boot/modem_fs1!
[ 29.557797] rmt_storage:INFO:rmt_storage_client_thread: Done Read (bytes = 512) for /boot/modem_fs1!
[ 29.569403] rmt_storage:INFO:rmt_storage_rw_iovec_cb: Read iovec request received for /boot/modem_fs2
[ 29.577970] rmt_storage:INFO:rmt_storage_client_thread: Calling Read [offset=512, size=512]for /boot/modem_fs2!
[ 29.588503] rmt_storage:INFO:rmt_storage_client_thread: Done Read (bytes = 512) for /boot/modem_fs2!
[ 29.599379] rmt_storage:INFO:rmt_storage_rw_iovec_cb: Read iovec request received for /boot/modem_fs1
[ 29.607863] rmt_storage:INFO:rmt_storage_client_thread: Calling Read [offset=1024, size=1571840]for /boot/modem_fs1!
[ 29.628910] rmt_storage:INFO:rmt_storage_client_thread: Done Read (bytes = 1571840) for /boot/modem_fs1!
[ 29.671962] init: write_file: Unable to open '/sys/block/dm-1/queue/read_ahead_kb': No such file or directory
[ 29.694182] init: service carrier_switcher does not have a SELinux domain defined
[ 29.731686] diag: In diag_send_feature_mask_update, control channel is not open, p: 0, c190cbac
[ 29.814085] init: Couldn't load properties from /data/local.prop: No such file or directory
[ 29.987463] scm_call failed: func id 0x2000c16, ret: -1, syscall returns: 0x0, 0x0, 0x0
[ 29.994734] memshare: hyp_assign_phys failed size=2097152 err=-5
[ 30.006559] init: property_set("ro.persistent_properties.ready", "true") failed: property already set
[ 30.020279] init: property_set("ro.boottime.logd-reinit", "30004582435") failed: property already set
[ 30.032958] init: ExecStart(update_verifier): Service not found
[ 30.038064] init: cannot find '/system/bin/install-recovery.sh', disabling 'flash_recovery': No such file or directory
[ 30.088227] init: cannot find '/vendor/bin/vppservice', disabling 'vppservice': No such file or directory
[ 30.096995] init: cannot find '/system/bin/qrngd', disabling 'qrngd': No such file or directory
[ 30.137552] init: cannot find '/system/bin/hvdcp_opti', disabling 'hvdcp_opti': No such file or directory
[ 30.143166] type=1400 audit(423456.239:14): avc: denied { net_raw } for pid=528 comm="pm-service" capability=13 scontext=u:r:per_mgr:s0 tcontext=u:r:per_mgr:s0 tclass=capability permissive=0
[ 30.143202] type=1400 audit(423459.279:15): avc: denied { chown } for pid=769 comm="ptt_socket_app" capability=0 scontext=u:r:wcnss_service:s0 tcontext=u:r:wcnss_service:s0 tclass=capability permissive=0
[ 30.146040] type=1400 audit(423459.279:15): avc: denied { chown } for pid=769 comm="ptt_socket_app" capability=0 scontext=u:r:wcnss_service:s0 tcontext=u:r:wcnss_service:s0 tclass=capability permissive=0
[ 30.146082] type=1400 audit(423459.279:16): avc: denied { setgid } for pid=769 comm="ptt_socket_app" capability=6 scontext=u:r:wcnss_service:s0 tcontext=u:r:wcnss_service:s0 tclass=capability permissive=0
[ 30.531223] init: cannot find '/system/vendor/bin/nqnfcinfo', disabling 'nqnfcinfo': No such file or directory
[ 30.611328] init: cannot find '/vendor/bin/ssgqmigd', disabling 'ssgqmigd': No such file or directory
[ 30.654379] init: cannot find '/vendor/bin/mlid', disabling 'mlid': No such file or directory
[ 30.708836] init: cannot find '/vendor/bin/qvop-daemon', disabling 'qvop-daemon': No such file or directory
[ 30.741421] init: cannot find '/system/vendor/bin/qseeproxydaemon', disabling 'qseeproxydaemon': No such file or directory
[ 30.767724] init: cannot find '/system/vendor/bin/qdmastatsd', disabling 'qdmastatsd': No such file or directory
[ 30.794342] init: cannot find '/vendor/bin/seemp_healthd', disabling 'seemp_healthd': No such file or directory
[ 30.830977] init: cannot find '/system/vendor/bin/qfp-daemon', disabling 'qfp-daemon': No such file or directory
[ 30.884318] init: cannot find '/system/vendor/bin/audiod', disabling 'audiod': No such file or directory
[ 30.893020] init: cannot find '/system/vendor/bin/dts_configurator', disabling 'dts_configurator': No such file or directory
[ 30.944287] init: cannot find '/system/vendor/bin/mdtpd', disabling 'mdtpd': No such file or directory
[ 30.952762] init: cannot find '/system/bin/fingerprintd', disabling 'fingerprintd': No such file or directory
[ 30.974267] init: cannot find '/system/bin/etsd', disabling 'etsd': No such file or directory
[ 31.048392] init: cannot find '/system/xbin/perfprofd', disabling 'perfprofd': No such file or directory
[ 31.054427] type=1400 audit(423459.279:16): avc: denied { setgid } for pid=769 comm="ptt_socket_app" capability=6 scontext=u:r:wcnss_service:s0 tcontext=u:r:wcnss_service:s0 tclass=capability permissive=0
[ 31.054472] type=1400 audit(423459.800:17): avc: denied { read } for pid=860 comm="cnss-daemon" name="u:object_r:wigig_prop:s0" dev="tmpfs" ino=98 scontext=u:r:wcnss_service:s0 tcontext=u:object_r:wigig_prop:s0 tclass=file permissive=0
[ 31.247590] init: cannot find '/system/vendor/bin/qmuxd', disabling 'qmuxd': No such file or directory
[ 31.298327] selinux: avc: denied { set } for property=wlan.driver.config pid=776 uid=1000 gid=1000 scontext=u:r:wcnss_service:s0 tcontext=u:object_r:wifi_prop:s0 tclass=property_service
[ 31.298327]
[ 31.353259] init: sys_prop(PROP_MSG_SETPROP2): permission denied uid:1000 name:wlan.driver.config
[ 31.399576] type=1400 audit(423459.800:17): avc: denied { read } for pid=860 comm="cnss-daemon" name="u:object_r:wigig_prop:s0" dev="tmpfs" ino=98 scontext=u:r:wcnss_service:s0 tcontext=u:object_r:wigig_prop:s0 tclass=file permissive=0
[ 31.603317] etspi_open
[ 31.654214] type=1400 audit(423460.140:18): avc: denied { read } for pid=776 comm="wcnss_service" name="u:object_r:serialno_prop:s0" dev="tmpfs" ino=124 scontext=u:r:wcnss_service:s0 tcontext=u:object_r:serialno_prop:s0 tclass=file permissive=0
[ 31.666353] init: do_stop: Service dhcpcd not found
[ 31.745394] init: cannot find '/system/vendor/bin/ipacm', disabling 'ipacm': No such file or directory
[ 32.366181] type=1400 audit(423460.140:18): avc: denied { read } for pid=776 comm="wcnss_service" name="u:object_r:serialno_prop:s0" dev="tmpfs" ino=124 scontext=u:r:wcnss_service:s0 tcontext=u:object_r:serialno_prop:s0 tclass=file permissive=0
[ 32.386990] type=1400 audit(423461.120:19): avc: denied { dac_override } for pid=911 comm="dpmd" capability=1 scontext=u:r:dpmd:s0 tcontext=u:r:dpmd:s0 tclass=capability permissive=0
[ 32.404890] type=1400 audit(423461.120:19): avc: denied { dac_override } for pid=911 comm="dpmd" capability=1 scontext=u:r:dpmd:s0 tcontext=u:r:dpmd:s0 tclass=capability permissive=0
[ 32.420318] type=1400 audit(423461.120:20): avc: denied { dac_read_search } for pid=911 comm="dpmd" capability=2 scontext=u:r:dpmd:s0 tcontext=u:r:dpmd:s0 tclass=capability permissive=0
[ 32.437130] type=1400 audit(423461.120:20): avc: denied { dac_read_search } for pid=911 comm="dpmd" capability=2 scontext=u:r:dpmd:s0 tcontext=u:r:dpmd:s0 tclass=capability permissive=0
[ 32.453330] type=1400 audit(423461.160:21): avc: denied { dac_override } for pid=911 comm="dpmd" capability=1 scontext=u:r:dpmd:s0 tcontext=u:r:dpmd:s0 tclass=capability permissive=0
[ 32.469731] type=1400 audit(423461.160:21): avc: denied { dac_override } for pid=911 comm="dpmd" capability=1 scontext=u:r:dpmd:s0 tcontext=u:r:dpmd:s0 tclass=capability permissive=0
[ 32.485827] type=1400 audit(423461.160:22): avc: denied { dac_read_search } for pid=911 comm="dpmd" capability=2 scontext=u:r:dpmd:s0 tcontext=u:r:dpmd:s0 tclass=capability permissive=0
[ 32.502437] type=1400 audit(423461.160:22): avc: denied { dac_read_search } for pid=911 comm="dpmd" capability=2 scontext=u:r:dpmd:s0 tcontext=u:r:dpmd:s0 tclass=capability permissive=0
[ 32.518851] type=1400 audit(423461.190:23): avc: denied { dac_override } for pid=911 comm="dpmd" capability=1 scontext=u:r:dpmd:s0 tcontext=u:r:dpmd:s0 tclass=capability permissive=0
[ 32.535291] type=1400 audit(423461.190:23): avc: denied { dac_override } for pid=911 comm="dpmd" capability=1 scontext=u:r:dpmd:s0 tcontext=u:r:dpmd:s0 tclass=capability permissive=0
[ 32.551336] type=1400 audit(423461.190:24): avc: denied { dac_read_search } for pid=911 comm="dpmd" capability=2 scontext=u:r:dpmd:s0 tcontext=u:r:dpmd:s0 tclass=capability permissive=0
[ 32.569960] selinux: avc: denied { set } for property=wlan.driver.ath pid=776 uid=1000 gid=1000 scontext=u:r:wcnss_service:s0 tcontext=u:object_r:wifi_prop:s0 tclass=property_service
[ 32.569960]
[ 32.576400] diag: In diag_send_feature_mask_update, control channel is not open, p: 2, c190cc9c
[ 32.596462] init: sys_prop(PROP_MSG_SETPROP2): permission denied uid:1000 name:wlan.driver.ath
[ 32.620719] type=1400 audit(423461.190:24): avc: denied { dac_read_search } for pid=911 comm="dpmd" capability=2 scontext=u:r:dpmd:s0 tcontext=u:r:dpmd:s0 tclass=capability permissive=0
[ 32.638011] type=1400 audit(423461.370:25): avc: denied { dac_override } for pid=911 comm="dpmd" capability=1 scontext=u:r:dpmd:s0 tcontext=u:r:dpmd:s0 tclass=capability permissive=0
[ 32.648799] QSEECOM: qseecom_load_app: App (egtzappf) does'nt exist, loading apps for first time
[ 32.662340] type=1400 audit(423461.370:25): avc: denied { dac_override } for pid=911 comm="dpmd" capability=1 scontext=u:r:dpmd:s0 tcontext=u:r:dpmd:s0 tclass=capability permissive=0
[ 32.678361] type=1400 audit(423461.370:26): avc: denied { dac_read_search } for pid=911 comm="dpmd" capability=2 scontext=u:r:dpmd:s0 tcontext=u:r:dpmd:s0 tclass=capability permissive=0
[ 32.695141] type=1400 audit(423461.370:26): avc: denied { dac_read_search } for pid=911 comm="dpmd" capability=2 scontext=u:r:dpmd:s0 tcontext=u:r:dpmd:s0 tclass=capability permissive=0
[ 32.711382] type=1400 audit(423461.370:27): avc: denied { dac_override } for pid=911 comm="dpmd" capability=1 scontext=u:r:dpmd:s0 tcontext=u:r:dpmd:s0 tclass=capability permissive=0
[ 32.727750] type=1400 audit(423461.370:27): avc: denied { dac_override } for pid=911 comm="dpmd" capability=1 scontext=u:r:dpmd:s0 tcontext=u:r:dpmd:s0 tclass=capability permissive=0
[ 32.732185] QSEECOM: qseecom_load_app: App with id 131074 (egtzappf) now loaded
[ 32.751107] type=1400 audit(423461.370:28): avc: denied { dac_read_search } for pid=911 comm="dpmd" capability=2 scontext=u:r:dpmd:s0 tcontext=u:r:dpmd:s0 tclass=capability permissive=0
[ 32.767767] type=1400 audit(423461.370:28): avc: denied { dac_read_search } for pid=911 comm="dpmd" capability=2 scontext=u:r:dpmd:s0 tcontext=u:r:dpmd:s0 tclass=capability permissive=0
[ 32.784064] type=1400 audit(423461.370:29): avc: denied { dac_override } for pid=911 comm="dpmd" capability=1 scontext=u:r:dpmd:s0 tcontext=u:r:dpmd:s0 tclass=capability permissive=0
[ 32.800502] type=1400 audit(423461.370:29): avc: denied { dac_override } for pid=911 comm="dpmd" capability=1 scontext=u:r:dpmd:s0 tcontext=u:r:dpmd:s0 tclass=capability permissive=0
[ 32.816512] type=1400 audit(423461.370:30): avc: denied { dac_read_search } for pid=911 comm="dpmd" capability=2 scontext=u:r:dpmd:s0 tcontext=u:r:dpmd:s0 tclass=capability permissive=0
[ 32.831778] QSEECOM: qseecom_unload_app: App id 131074 now unloaded
[ 32.833402] etspi_release
[ 32.834624] etspi_open
[ 32.855793] QSEECOM: qseecom_load_app: App (egtzappf) does'nt exist, loading apps for first time
[ 32.874445] selinux: avc: denied { set } for property=persist.vendor.camera.debug.logfile pid=870 uid=1006 gid=1006 scontext=u:r:mm-qcamerad:s0 tcontext=u:object_r:default_prop:s0 tclass=property_service
[ 32.874445]
[ 32.893365] init: sys_prop(PROP_MSG_SETPROP2): permission denied uid:1006 name:persist.vendor.camera.debug.logfile
[ 32.924174] msm_sensor_fill_eeprom_subdevid_by_name:222 Eeprom userspace probe for ov5675_kingcome
[ 32.940144] QSEECOM: qseecom_load_app: App with id 196610 (egtzappf) now loaded
[ 32.976272] msm_sensor_match_id chip id 35c does not match 5675
[ 32.981157] msm_sensor_check_id:1400 match id failed rc -19
[ 33.013367] QSEECOM: qseecom_unload_app: App id 196610 now unloaded
[ 33.020564] etspi_release
[ 33.049504] init: kill(893, 9) failed: No such process
[ 33.058289] msm_sensor_match_id chip id 35c does not match 5675
[ 33.063179] msm_sensor_check_id:1400 match id failed rc -19
[ 33.149278] msm_sensor_match_id chip id 35c does not match 5675
[ 33.154258] msm_sensor_check_id:1400 match id failed rc -19
[ 33.194055] ov5675 power up failed
[ 33.196297] MSM-SENSOR-INIT msm_sensor_driver_cmd:82 msm_sensor_driver_cmd failed (non-fatal) rc -19
[ 33.213658] msm_qti_pp_get_rms_value_control, back not active to query rms be_idx:3
[ 33.222588] msm_sensor_fill_eeprom_subdevid_by_name:222 Eeprom userspace probe for s5k4h7_ofilm
[ 33.226563] msm_dolby_dap_param_to_get_control_get, port_id not set, do not query ADM
[ 33.227068] msm_dolby_dap_param_visualizer_control_get Incorrect VCNB length
[ 33.227068] msm_voice_sound_focus_get: Error getting Sound Focus Params, err=-22
[ 33.227169] msm_voice_source_tracking_get: Error getting Source Tracking Params, err=-22
[ 33.227270] msm_audio_get_copp_idx_from_port_id: Invalid FE, exiting
[ 33.227273] msm_audio_sound_focus_get: Could not get copp idx for port_id=16385
[ 33.227375] msm_audio_get_copp_idx_from_port_id: Invalid FE, exiting
[ 33.227377] msm_audio_source_tracking_get: Could not get copp idx for port_id=16385
[ 33.227482] msm_voice_sound_focus_get: Error getting Sound Focus Params, err=-22
[ 33.227603] msm_voice_source_tracking_get: Error getting Source Tracking Params, err=-22
[ 33.227703] msm_audio_get_copp_idx_from_port_id: Invalid FE, exiting
[ 33.227706] msm_audio_sound_focus_get: Could not get copp idx for port_id=4101
[ 33.227802] msm_audio_get_copp_idx_from_port_id: Invalid FE, exiting
[ 33.227805] msm_audio_source_tracking_get: Could not get copp idx for port_id=4101
[ 33.227902] msm_audio_get_copp_idx_from_port_id: Invalid FE, exiting
[ 33.227905] msm_audio_sound_focus_get: Could not get copp idx for port_id=4103
[ 33.228005] msm_audio_get_copp_idx_from_port_id: Invalid FE, exiting
[ 33.228008] msm_audio_source_tracking_get: Could not get copp idx for port_id=4103
[ 33.229827] msm_pcm_volume_ctl_get substream runtime not found
[ 33.230404] msm_pcm_volume_ctl_get substream runtime not found
[ 33.230926] msm_pcm_volume_ctl_get substream runtime not found
[ 33.231153] msm_compr_audio_effects_config_get: stream or effects inactive
[ 33.232270] msm_pcm_volume_ctl_get substream runtime not found
[ 33.232957] msm_pcm_volume_ctl_get substream runtime not found
[ 33.233066] msm_pcm_volume_ctl_get substream or runtime not found
[ 33.234323] msm_compr_audio_effects_config_get: stream or effects inactive
[ 33.234878] msm_compr_audio_effects_config_get: stream or effects inactive
[ 33.235402] msm_compr_audio_effects_config_get: stream or effects inactive
[ 33.235974] msm_compr_audio_effects_config_get: stream or effects inactive
[ 33.236486] msm_compr_audio_effects_config_get: stream or effects inactive
[ 33.237046] msm_compr_audio_effects_config_get: stream or effects inactive
[ 33.237656] msm_compr_audio_effects_config_get: stream or effects inactive
[ 33.238169] msm_compr_audio_effects_config_get: stream or effects inactive
[ 33.238614] msm_pcm_volume_ctl_get substream or runtime not found
[ 33.238987] msm_compr_audio_effects_config_get: stream or effects inactive
[ 33.239560] msm_compr_audio_effects_config_get: stream or effects inactive
[ 33.240130] msm_compr_audio_effects_config_get: stream or effects inactive
[ 33.289191] type=1400 audit(423461.370:30): avc: denied { dac_read_search } for pid=911 comm="dpmd" capability=2 scontext=u:r:dpmd:s0 tcontext=u:r:dpmd:s0 tclass=capability permissive=0
[ 33.289234] type=1400 audit(423462.040:31): avc: denied { read } for pid=479 comm="HwBinder:479_1" name="class" dev="sysfs" ino=10 scontext=u:r:hal_audio_default:s0 tcontext=u:object_r:sysfs:s0 tclass=dir permissive=0
[ 33.433764] wcdcal_hwdep_ioctl_shared: codec didn't set this 0!!
[ 33.434758] wcdcal_hwdep_ioctl_shared: codec didn't set this 3!!
[ 33.553382] s5k4h7 probe succeeded
[ 33.578279] msm_sensor_init_device_name 684
[ 33.581852] msm_sensor_init_device_name 700
[ 33.597285] msm_sensor_fill_eeprom_subdevid_by_name:222 Eeprom userspace probe for s5k3l8_truly
[ 33.622980] s5k3l8 probe succeeded
[ 33.641438] msm_sensor_init_device_name 684
[ 33.644801] Macle android_camera already created
[ 33.661030] msm_csid_irq CSID1_IRQ_STATUS_ADDR = 0x800
[ 33.667402] msm_csid_irq CSID0_IRQ_STATUS_ADDR = 0x800
[ 33.777735] wcnss: no space available for smd frame
[ 33.804098] wcnss: no space available for smd frame
[ 33.834105] wcnss: no space available for smd frame
[ 33.864075] wcnss: no space available for smd frame
[ 33.976276] init: property_set("ro.vendor.ril.svlte1x", "false") failed: property already set
[ 33.985466] init: property_set("ro.vendor.ril.svdo", "false") failed: property already set
[ 35.012256] MSM-CPP cpp_init_hardware:1023 stream_cnt:0
[ 35.092772] type=1400 audit(423462.040:31): avc: denied { read } for pid=479 comm="HwBinder:479_1" name="class" dev="sysfs" ino=10 scontext=u:r:hal_audio_default:s0 tcontext=u:object_r:sysfs:s0 tclass=dir permissive=0
[ 35.111106] type=1400 audit(423463.840:32): avc: denied { read } for pid=870 comm="mm-qcamera-daem" name="name" dev="sysfs" ino=40882 scontext=u:r:mm-qcamerad:s0 tcontext=u:object_r:sysfs_graphics:s0 tclass=file permissive=0
[ 35.131228] type=1400 audit(423463.840:32): avc: denied { read } for pid=870 comm="mm-qcamera-daem" name="name" dev="sysfs" ino=40882 scontext=u:r:mm-qcamerad:s0 tcontext=u:object_r:sysfs_graphics:s0 tclass=file permissive=0
[ 35.150921] type=1400 audit(423463.840:33): avc: denied { read } for pid=870 comm="mm-qcamera-daem" name="name" dev="sysfs" ino=40931 scontext=u:r:mm-qcamerad:s0 tcontext=u:object_r:sysfs_graphics:s0 tclass=file permissive=0
[ 35.275123] selinux: avc: denied { set } for property=persist.vendor.camera.debug.logfile pid=870 uid=1006 gid=1006 scontext=u:r:mm-qcamerad:s0 tcontext=u:object_r:default_prop:s0 tclass=property_service
[ 35.275123]
[ 35.294056] init: sys_prop(PROP_MSG_SETPROP2): permission denied uid:1006 name:persist.vendor.camera.debug.logfile
[ 35.311350] msm_csid_irq CSID0_IRQ_STATUS_ADDR = 0x800
[ 35.328496] MSM-CPP cpp_init_hardware:1023 stream_cnt:0
selinux: avc: denied { set } for property=persist.vendor.camera.debug.logfile pid=870 uid=1006 gid=1006 scontext=u:r:mm-qcamerad:s0 tcontext=u:object_r:default_prop:s0 tclass=property_service
[ 35.494686]
[ 35.512183] init: sys_prop(PROP_MSG_SETPROP2): permission denied uid:1006 name:persist.vendor.camera.debug.logfile
[ 35.528519] msm_csid_irq CSID1_IRQ_STATUS_ADDR = 0x800
[ 35.542645] MSM-CPP cpp_init_hardware:1023 stream_cnt:0
selinux: avc: denied { set } for property=persist.vendor.camera.debug.logfile pid=870 uid=1006 gid=1006 scontext=u:r:mm-qcamerad:s0 tcontext=u:object_r:default_prop:s0 tclass=property_service
[ 35.700998]
[ 35.718596] init: sys_prop(PROP_MSG_SETPROP2): permission denied uid:1006 name:persist.vendor.camera.debug.logfile
[ 35.734776] msm_csid_irq CSID0_IRQ_STATUS_ADDR = 0x800
[ 35.745685] MSM-CPP cpp_init_hardware:1023 stream_cnt:0
selinux: avc: denied { set } for property=persist.vendor.camera.debug.logfile pid=870 uid=1006 gid=1006 scontext=u:r:mm-qcamerad:s0 tcontext=u:object_r:default_prop:s0 tclass=property_service
[ 35.938475]
[ 35.956010] init: sys_prop(PROP_MSG_SETPROP2): permission denied uid:1006 name:persist.vendor.camera.debug.logfile
[ 35.975829] msm_csid_irq CSID1_IRQ_STATUS_ADDR = 0x800
[ 35.988381] MSM-CPP cpp_init_hardware:1023 stream_cnt:0
[ 36.218093] init: property_set("ro.boottime.fps_hal", "36202457328") failed: property already set
[ 36.294268] etspi_open
[ 36.315878] QSEECOM: qseecom_load_app: App (egtzappf) does'nt exist, loading apps for first time
[ 36.400436] QSEECOM: qseecom_load_app: App with id 262146 (egtzappf) now loaded
[ 36.479950] QSEECOM: qseecom_unload_app: App id 262146 now unloaded
[ 36.486455] etspi_release
[ 36.488595] etspi_open
[ 36.504748] QSEECOM: qseecom_load_app: App (egtzappf) does'nt exist, loading apps for first time
[ 36.590292] QSEECOM: qseecom_load_app: App with id 327682 (egtzappf) now loaded
[ 36.635598] type=1400 audit(423463.840:33): avc: denied { read } for pid=870 comm="mm-qcamera-daem" name="name" dev="sysfs" ino=40931 scontext=u:r:mm-qcamerad:s0 tcontext=u:object_r:sysfs_graphics:s0 tclass=file permissive=0
[ 36.654532] type=1400 audit(423465.390:34): avc: denied { read } for pid=1356 comm="system-server-i" name="u:object_r:graphics_vulkan_prop:s0" dev="tmpfs" ino=104 scontext=u:r:system_server:s0 tcontext=u:object_r:graphics_vulkan_prop:s0 tclass=file permissive=0
[ 36.686903] QSEECOM: qseecom_unload_app: App id 327682 now unloaded
[ 36.693614] etspi_release
[ 36.715750] init: kill(1407, 9) failed: No such process
[ 39.297750] type=1400 audit(423465.390:34): avc: denied { read } for pid=1356 comm="system-server-i" name="u:object_r:graphics_vulkan_prop:s0" dev="tmpfs" ino=104 scontext=u:r:system_server:s0 tcontext=u:object_r:graphics_vulkan_prop:s0 tclass=file permissive=0
[ 39.319974] type=1400 audit(423468.050:35): avc: denied { read write } for pid=489 comm="[email protected]" name="brightness" dev="sysfs" ino=29059 scontext=u:r:hal_light_default:s0 tcontext=u:object_r:sysfs:s0 tclass=file permissive=0
[ 40.134523] pgd = db4b0000
[ 40.136187] [00000000] *pgd=00000000
[ 40.198107] pgd = db4b0000
[ 40.199775] [00000000] *pgd=00000000
[ 41.221840] init: property_set("ro.boottime.fps_hal", "41206023732") failed: property already set
[ 41.308220] etspi_open
[ 41.342550] QSEECOM: qseecom_load_app: App (egtzappf) does'nt exist, loading apps for first time
[ 41.429623] QSEECOM: qseecom_load_app: App with id 393218 (egtzappf) now loaded
[ 41.520693] QSEECOM: qseecom_unload_app: App id 393218 now unloaded
[ 41.527352] etspi_release
[ 41.529401] etspi_open
[ 41.552509] QSEECOM: qseecom_load_app: App (egtzappf) does'nt exist, loading apps for first time
[ 41.638155] QSEECOM: qseecom_load_app: App with id 458754 (egtzappf) now loaded
[ 41.717463] QSEECOM: qseecom_unload_app: App id 458754 now unloaded
[ 41.724315] etspi_release
[ 41.767116] init: kill(1648, 9) failed: No such process
[ 42.148135] selinux: avc: denied { set } for property=persist.vendor.camera.debug.logfile pid=870 uid=1006 gid=1006 scontext=u:r:mm-qcamerad:s0 tcontext=u:object_r:default_prop:s0 tclass=property_service
[ 42.148135]
[ 42.167221] init: sys_prop(PROP_MSG_SETPROP2): permission denied uid:1006 name:persist.vendor.camera.debug.logfile
[ 42.188020] msm_csid_irq CSID0_IRQ_STATUS_ADDR = 0x800
[ 42.217299] MSM-CPP cpp_init_hardware:1023 stream_cnt:0
[ 42.375448] pgd = db4b0000
[ 42.377110] [00000000] *pgd=00000000
[ 42.399982] pgd = db4b0000
[ 42.401645] [00000000] *pgd=00000000
[ 43.793492] type=1400 audit(423471.110:36): avc: denied { read write } for pid=489 comm="[email protected]" name="brightness" dev="sysfs" ino=29059 scontext=u:r:hal_light_default:s0 tcontext=u:object_r:sysfs:s0 tclass=file permissive=0
[ 43.813295] type=1400 audit(423472.540:37): avc: denied { read } for pid=1908 comm="m.android.phone" name="u:object_r:graphics_vulkan_prop:s0" dev="tmpfs" ino=104 scontext=u:r:radio:s0 tcontext=u:object_r:graphics_vulkan_prop:s0 tclass=file permissive=0
[ 43.835899] type=1400 audit(423472.540:37): avc: denied { read } for pid=1908 comm="m.android.phone" name="u:object_r:graphics_vulkan_prop:s0" dev="tmpfs" ino=104 scontext=u:r:radio:s0 tcontext=u:object_r:graphics_vulkan_prop:s0 tclass=file permissive=0
[ 43.858095] type=1400 audit(423472.540:38): avc: denied { read } for pid=1908 comm="m.android.phone" name="u:object_r:opengles_prop:s0" dev="tmpfs" ino=88 scontext=u:r:radio:s0 tcontext=u:object_r:opengles_prop:s0 tclass=file permissive=0
[ 44.713763] init: cannot find '/vendor/bin/init.qcom.crashdata.sh', disabling 'exec 6 (/vendor/bin/init.qcom.crashdata.sh)': No such file or directory
[ 44.726431] init: Could not start exec service
[ 44.737160] init: cannot find '/system/bin/qrngp', disabling 'qrngp': No such file or directory
[ 44.754769] init: cannot execve('/system/etc/init.qcom.testscripts.sh'): Permission denied
[ 44.773624] type=1400 audit(423472.540:38): avc: denied { read } for pid=1908 comm="m.android.phone" name="u:object_r:opengles_prop:s0" dev="tmpfs" ino=88 scontext=u:r:radio:s0 tcontext=u:object_r:opengles_prop:s0 tclass=file permissive=0
[ 44.848809] type=1400 audit(423473.600:42): avc: denied { write } for pid=2155 comm="init.qcom.post_" name="interactive" dev="sysfs" ino=42455 scontext=u:r:qti_init_shell:s0 tcontext=u:object_r:sysfs_devices_system_cpu:s0 tclass=dir permissive=0
[ 44.884479] type=1400 audit(423473.600:42): avc: denied { write } for pid=2155 comm="init.qcom.post_" name="interactive" dev="sysfs" ino=42455 scontext=u:r:qti_init_shell:s0 tcontext=u:object_r:sysfs_devices_system_cpu:s0 tclass=dir permissive=0
[ 44.905414] type=1400 audit(423473.610:43): avc: denied { write } for pid=2155 comm="init.qcom.post_" name="interactive" dev="sysfs" ino=42474 scontext=u:r:qti_init_shell:s0 tcontext=u:object_r:sysfs_devices_system_cpu:s0 tclass=dir permissive=0
[ 44.954714] type=1400 audit(423473.610:43): avc: denied { write } for pid=2155 comm="init.qcom.post_" name="interactive" dev="sysfs" ino=42474 scontext=u:r:qti_init_shell:s0 tcontext=u:object_r:sysfs_devices_system_cpu:s0 tclass=dir permissive=0
[ 44.976328] type=1400 audit(423473.680:44): avc: denied { read } for pid=2173 comm="cat" name="meminfo" dev="proc" ino=4026532294 scontext=u:r:qti_init_shell:s0 tcontext=u:object_r:proc_meminfo:s0 tclass=file permissive=0
[ 44.996624] CPU2: shutdown
[ 45.157545] CPU0: shutdown
[ 46.662284] CPU1: shutdown
[ 47.410273] type=1400 audit(423473.680:44): avc: denied { read } for pid=2173 comm="cat" name="meminfo" dev="proc" ino=4026532294 scontext=u:r:qti_init_shell:s0 tcontext=u:object_r:proc_meminfo:s0 tclass=file permissive=0
[ 47.429197] type=1400 audit(423476.160:45): avc: granted { execute } for pid=1356 comm="system_server" path="/data/dalvik-cache/arm/system@[email protected]@[email protected]" dev="dm-0" ino=104786 scontext=u:r:system_server:s0 tcontext=u:object_r:dalvikcache_data_file:s0 tclass=file
[ 48.925506] CPU2: shutdown
[ 48.939851] CPU0: shutdown
[ 48.953785] CPU1: shutdown
[ 49.226199] CPU2: shutdown
[ 50.483883] init: property_set("ro.boottime.fps_hal", "50468079510") failed: property already set
[ 50.617958] etspi_open
---------------------
作者：RadianceBlau
来源：CSDN
原文：https://blog.csdn.net/RadianceBlau/article/details/78416776
版权声明：本文为博主原创文章，转载请附上博文链接！