C1. Introduction-2 & C2. AIDA File Tool-1

与Exaopc软件的关系

AIDA数据生成器与Exaopc有联系。它通过Exaopc收集DCS数据并为AIDA创建数据文件。图1-2显示了AIDA / AIDA数据文件生成器/ Exaopc之间的关系。

Fig. C 1.1 Relationship with other packages 图C 1.1与其他软件包的关系

与其它软件的关系

参见上图。
如以下系统配置图中所述，Exaopc站应与DCS联网。Exaopc软件的安装和操作应参考各自的手册（IM 36J06D20-01E和36J02A12-01E）
与Exasmoc在线控制器相同，通常AIDA数据归档工具在Exaopc工作站上运行。因此，硬件和软件要求与Exasmoc相同。Exaopc提供了数据采集接口。AIDA数据生成器可以根据选项对话框窗口中的定义（按照本手册中的说明）连接到Exaopc服务器。
AIDA数据生成器创建的数据文件由AIDA软件用于AIDA模型辨识，该文件还提供给用于SMOC-PC为Exasmoc在线控制器创建.CON文件。

C2. AIDA文件工具

AIDA文件工具生成用于AIDA数据分析和模型辨识工具的数据文件。通过Exaopc OPC数据服务器和历史数据服务器从DCS采集数据。该工具安装在文件夹“(Installed drive):¥¥ProgramFiles¥YOKOGAWA¥IA¥iPCS¥Product¥EXA¥Program”。
从R4.01起，单击以下模块。
“(Installed drive):¥¥Program Files¥YOKOGAWA¥IA¥iPCS¥Product¥EXA¥Program¥AIDAFile Gen.exe”

C2.1数据归档工具面板

Fig. C 2.1 AIDA Data Archiving Tool 图C 2.1 AIDA数据归档工具

 项目说明

表C 2-1操作员和工程师输入/显示参数

| 条目| 描述 | 操作员模式 | 工程师模式|
| ------------- |:-------------:| -----:|
| Definition File（定义文件） | 显示所选位号定义文件的路径。从右侧的浏览菜单指定路径。| R/W | R/W
| Data File（数据文件）| 显示所选数据文件的路径。路径由右侧的浏览菜单指定。| R/W| R/W
| Item ID（条目ID）| 当生成一个新定义的位号时，指定ItemID。在浏览菜单中直接指定或选择ItemID。 | R/W| R/W
| Browse （浏览）| 显示可用的ItemID。选中的ItemID被添加到右侧的网格面板。该功能在连接OPC服务器后可用。| R| R
| Delete (删除)| 删除数据网格表上所选的ItemID。| R| R
| Append（附加）| 在上述的ItemID字段上添加指定的ItemID。| R| R
| Data Type(数据类型)| 在定义要生成的新位号条目时，选择数据类型（历史趋势或预测趋势值）。| R/W | R/W

---

原文：

Relationship with Exaopc software

AIDA Data Generator has relationship with Exaopc. It collects DCS data via Exaopc and create data file for AIDA. Figure1-2 shows the relationship between AIDA/AIDA data file generator/Exaopc.

Relationship with other software

Refer the above figure.
Exaopc station should be networked with DCS as explained in the following System configuration figures. Exaopc software installation and operation shall be referred from respective manuals (IM 36J06D20-01E and 36J02A12-01E)
Usually AIDA Data Archiving Tool runs on the Exaopc station, same as Exasmoc online controller. Hence the hardware and software requirement are the same as Exasmoc. Exaopc provides the data collection interface. AIDA Data Generator can connect to Exaopc server according to the definition in the option dialog window (as instructed in this manual).
Data file created by AIDA Data Generator is used by AIDA software for AIDA model identification, which also provides the file for use with SMOC-PC for creating .CON file for Exasmoc online controller.

C2. AIDA File Tool

AIDA file tool generates a data file for AIDA data analysis and model identification tool. Data is collected from DCS via Exaopc OPC data server and Historical data server. The tool is installed under the folder “(Installed drive):¥¥Program Files¥YOKOGAWA¥IA¥iPCS¥Product ¥EXA¥Program”.
From R4.01, click the following module.
“(Installed drive):¥¥Program Files¥YOKOGAWA¥IA¥iPCS¥Product¥EXA¥Program¥AIDAFile Gen.exe”

C2.1 Data Archiving Tool Panel

 Description of items

Table C 2-1 Operator and engineer entry/display parameters

| Item | Description | Operator Mode | Engineer Mode|
| ------------- |:-------------:| -----:|
| Definition File| Path of the selected tag definition file is displayed. Path is specified from the browse menu on the right side. | R/W| R/W
| Data File| Path of the selected data file is displayed. Path is specified from the browse menu on the right side. | R/W | R/W
| Item ID | Specify the ItemID when defining a new tag item to be generated. ItemID is directly specified or selected form the browse menu. | R/W| R/W
| Browse | Available itemID is displayed. Selected ItemID is added to the grid panel on the right side. The function is available after OPC server is connected. | R | R
| Delete | Delete the selected ItemID on the Data grid table. | R| R
| Append | Add the specified ItemID on the ItemID field above. | R| R
| Data Type | Select the Data Type when defining a new tag item to be generated, future value or past trend value. | R/W | R/W

---

2017.2.21