[ROC-RK3568-PC] [Firefly-Android] 10min带你了解LCD的使用
- 博主主页： 【Systemcall小酒屋】
- 博主追寻：热衷于用简单的案例讲述复杂的技术，“假传万卷书，真传一案例”，这是林群院士说过的一句话，另外“成就是最好的老师”，技术既要沉淀，也得分享，成就感的正反馈是支持我持续耕耘的动力！
- 专栏目录： 【Firefly-RK356x板卡】
- 专栏说明：基于Firefly旗下的RK356x板卡进行入门篇讲述，欢迎订阅，博主会持续更新！
文章目录
-
- 一、内核Config配置
- 二、MIPI配置
-
- 2.1 引脚配置
- 2.2 背光配置
- 2.3 显示时序配置
-
- 2.3.1 Power on/off sequence
- 2.3.2 Display-Timings
- 三、EDP配置
-
- 3.1 引脚配置
- 3.2 EDP背光配置
一、内核Config配置
ROC-RK3568-PC的SDK下kernel/arch/arm64/configs/firefly_defconfig已经把LCD相关的配置好：
CONFIG_DRM_ROCKCHIP=y
CONFIG_ROCKCHIP_DW_MIPI_DSI=y
CONFIG_DRM_PANEL_SIMPLE=y
二、MIPI配置
ROC-RK3568-PC的SDK有MIPI DSI的DTS文件： kernel/arch/arm64/boot/dts/rockchip/rk3568-firefly-roc-pc-mipi101_M101014_BE45_A1.dts，此DTS文件为MIPI_DSI0+HDMI屏配置，MIPI_DSI1 默认关闭。
2.1 引脚配置
从DTS文件中可以看到以下语句：
#include "rk3568-firefly-roc-pc.dtsi"
/ {
model = "ROC-RK3568-PC MIPI M101014_BE45_A1 + HDMI(Android)";
compatible = "rockchip,rk3568-firefly-roc-pc-mipi", "rockchip,rk3568";
...
}
&route_dsi0 {
status = "okay";
logo,rotation = "logo_rotation_270"; //support rotation 90,180,270
connect = <&vp1_out_dsi0>;
};
&video_phy0 {
status = "okay";
};
&dsi0_in_vp0 {
status = "disabled";
};
&dsi0_in_vp1 {
status = "okay";
};
/*
* mipi_dphy0 needs to be enabled
* when dsi0 is enabled
*/
&dsi0 {
status = "okay";
//rockchip,lane-rate = <1000>;
dsi0_panel: panel@0 {
status = "okay";
compatible = "simple-panel-dsi";
reg = <0>;
backlight = <&backlight>;
enable-gpios = <&gpio0 RK_PC7 GPIO_ACTIVE_HIGH>;
reset-gpios = <&gpio3 RK_PB5 GPIO_ACTIVE_LOW>;
enable-delay-ms = <35>;
prepare-delay-ms = <6>;
reset-delay-ms = <25>;
init-delay-ms = <55>;
unprepare-delay-ms = <0>;
disable-delay-ms = <20>;
mipi-data-delay-ms = <200>;
...
panel-init-sequence = [
//39 00 04 B9 83 10 2E
// 15 00 02 CF FF
05 78 01 11
05 32 01 29
//15 00 02 35 00
];
panel-exit-sequence = [
05 00 01 28
05 00 01 10
];
...
};
};
...
&route_hdmi {
status = "okay";
connect = <&vp0_out_hdmi>;
};
&hdmi {
status = "okay";
};
&hdmi_in_vp0 {
status = "okay";
};
&hdmi_in_vp1 {
status = "disabled";
};
...
这里定义了LCD的控制引脚：
| NAME | GPIO | GPIO ACTIVE |
|---|---|---|
| LCD_EN | GPIO0_C7 | GPIO_ACTIVE_HIGH |
| LCD_RST | GPIO3_B5 | GPIO_ACTIVE_LOW |
在硬件信号上 LCD_EN 引脚高电平有效，而 LCD_RST 引脚是低电平有效。
2.2 背光配置
在DTS文件中配置了背光信息，如下：
backlight: backlight {
status = "okay";
compatible = "pwm-backlight";
enable-gpios = <&gpio3 RK_PB0 GPIO_ACTIVE_HIGH>;
pwms = <&pwm4 0 50000 1>;
brightness-levels = <
60 60 60 61 61 61 62 62
62 63 63 63 64 64 64 65
65 65 66 66 66 67 67 67
68 68 68 69 69 69 70 70
70 71 71 71 72 72 72 73
73 73 74 74 74 75 75 75
76 76 76 77 77 77 78 78
78 79 79 79 80 80 80 81
81 81 82 82 82 83 83 83
84 84 84 85 85 85 86 86
86 87 87 87 88 88 88 89
89 89 90 91 92 93 94 95
96 97 98 99 100 101 102 103
104 105 106 107 108 109 110 111
112 113 114 115 116 117 118 119
120 121 122 123 124 125 126 127
128 129 130 131 132 133 134 135
136 137 138 139 140 141 142 143
144 145 146 147 148 149 150 151
152 153 154 155 156 157 158 159
160 161 162 163 164 165 166 167
168 169 170 171 172 173 174 175
176 177 178 179 180 181 182 183
184 185 186 187 188 189 190 191
192 193 194 195 196 197 198 199
200 201 202 203 204 205 206 207
208 209 210 211 212 213 214 215
216 217 218 219 220 221 222 223
224 225 226 227 228 229 230 231
232 233 234 235 236 237 238 239
240 241 242 243 244 245 246 247
248 249 250 251 252 253 254 255
>;
default-brightness-level = <200>;
};
-
enable-gpios：背光使能脚，高电平有效。
-
pwms属性：配置PWM，范例里面默认使用pwm4，50000ns是周期(20 KHz)，pwm为负极性。
-
brightness-levels属性：配置背光亮度数组，一般以值 255 为一个 scale，当 PWM 设置为正极性时，从 0~255 表示背光为正极，占空比从 0%~100% 变化，255~0 为负极性，占空比从 100%~0% 变化；当 PWM 设置为负极性时，反之。
-
default-brightness-level属性：开机时默认背光亮度，范围为0-255。
具体可参考kernel中的说明文档：kernel/Documentation/devicetree/bindings/leds/backlight/pwm-backlight.txt
2.3 显示时序配置
2.3.1 Power on/off sequence
MIPI屏的上下电时序通常都在规格书的Power on/off sequence章节中，可根据规格书的上下电时序修改dts，panel节点中有如下属性:
&dsi0 {
status = "okay";
//rockchip,lane-rate = <1000>;
dsi0_panel: panel@0 {
status = "okay";
compatible = "simple-panel-dsi";
...
enable-delay-ms = <35>;
prepare-delay-ms = <6>;
reset-delay-ms = <25>;
init-delay-ms = <55>;
unprepare-delay-ms = <0>;
disable-delay-ms = <20>;
mipi-data-delay-ms = <200>;
...
};
};
mipi-data-delay-ms为Firefly 10.1寸 M101014-BE45-A1 MIPI屏所需时序，调试屏幕时可根据本身上下电时序是否需要再配置此属性。MIPI上下电后需要发送初始化或退出指令才能使之正常工作，初始化和退出指令列表可以参考kernel/arch/arm64/boot/dts/rockchip/rk3568-firefly-roc-pc-mipi101_CZNB101862T.dts，列表如下：
&dsi0 {
status = "okay";
//rockchip,lane-rate = <1000>;
dsi0_panel: panel@0 {
...
panel-init-sequence = [
15 00 02 E0 00
15 00 02 E1 93
15 00 02 E2 65
15 00 02 E3 F8
15 00 02 E0 04
15 00 02 2D 03
15 00 02 E0 00
15 00 02 80 03
//15 00 02 4A 35
15 00 02 E0 01
15 00 02 00 00
15 00 02 E0 01
15 00 02 4B 04
//15 00 02 4A 35
15 00 02 00 00
15 00 02 01 66
//15 00 02 03 00
//15 00 02 04 6D
15 00 02 17 00
15 00 02 18 AF
15 00 02 19 01
...
];
panel-exit-sequence = [
05 05 01 28
05 78 01 10
];
};
};
dts中的init-sequence和panel-exit-sequence，只是配置了上电和下电指令, 其他的初始化指令已经烧录在M101014-BE45-A1这款MIPI屏的IC里，dts无需配置。接下来来看看上下电时序在驱动中的实现， 具体实现在kernel/drivers/gpu/drm/panel/panel-simple.c中：
static int panel_simple_disable(struct drm_panel *panel)
{
...
if (p->backlight) {
p->backlight->props.power = FB_BLANK_POWERDOWN;
p->backlight->props.state |= BL_CORE_FBBLANK;
backlight_update_status(p->backlight);
}
if (p->desc->delay.disable)
panel_simple_sleep(p->desc->delay.disable);
if (p->cmd_type == CMD_TYPE_MCU) {
err = panel_simple_xfer_mcu_cmd_seq(p, p->desc->exit_seq);
if (err)
dev_err(panel->dev, "failed to send exit cmds seq\n");
}
...
}
static int panel_simple_unprepare(struct drm_panel *panel)
{
...
if (p->desc->exit_seq) {
if (p->dsi)
panel_simple_xfer_dsi_cmd_seq(p, p->desc->exit_seq);
else if (p->cmd_type == CMD_TYPE_SPI)
err = panel_simple_xfer_spi_cmd_seq(p, p->desc->exit_seq);
if (err)
dev_err(panel->dev, "failed to send exit cmds seq\n");
}
gpiod_direction_output(p->reset_gpio, 1);
if(!p->enable_on_always){
gpiod_direction_output(p->enable_gpio, 0);
}
...
}
static int panel_simple_prepare(struct drm_panel *panel)
{
...
gpiod_direction_output(p->enable_gpio, 1);
if (p->desc->delay.prepare)
panel_simple_sleep(p->desc->delay.prepare);
...
gpiod_direction_output(p->reset_gpio, 1);
if (p->desc->delay.reset)
panel_simple_sleep(p->desc->delay.reset);
gpiod_direction_output(p->reset_gpio, 0); //由于驱动在控制reset脚时序的时候使用了`gpiod`这类的API
//如果在DTS配置了低电平有效，那么这里就会将reset引脚拉高，即取反。
if (p->desc->delay.init)
panel_simple_sleep(p->desc->delay.init);
if (p->desc->init_seq) {
if (p->dsi)
panel_simple_xfer_dsi_cmd_seq(p, p->desc->init_seq);
else if (p->cmd_type == CMD_TYPE_SPI)
err = panel_simple_xfer_spi_cmd_seq(p, p->desc->init_seq);
if (err)
dev_err(panel->dev, "failed to send init cmds seq\n");
}
if(p->desc->delay.mipi_data){
panel_simple_sleep(p->desc->delay.mipi_data);
}
...
}
static int panel_simple_enable(struct drm_panel *panel)
{
...
if (p->cmd_type == CMD_TYPE_MCU) {
err = panel_simple_xfer_mcu_cmd_seq(p, p->desc->init_seq);
if (err)
dev_err(panel->dev, "failed to send init cmds seq\n");
}
if (p->desc->delay.enable)
panel_simple_sleep(p->desc->delay.enable);
if (p->backlight) {
p->backlight->props.state &= ~BL_CORE_FBBLANK;
p->backlight->props.power = FB_BLANK_UNBLANK;
backlight_update_status(p->backlight);
}
...
}
2.3.2 Display-Timings
display_timings在dts中定义：
disp_timings0: display-timings {
native-mode = <&dsi0_timing0>;
dsi0_timing0: timing0 {
clock-frequency = <72600000>;//<80000000>;
hactive = <800>;//<768>;
vactive = <1280>;
hsync-len = <14>; //20, 50,10
hback-porch = <26>; //50, 56,10
hfront-porch = <32>;//50, 30,180
vsync-len = <8>;//4
vback-porch = <20>;//4
vfront-porch = <80>;//8
hsync-active = <0>;
vsync-active = <0>;
de-active = <0>;
pixelclk-active = <0>;
};
};
相关的参数一般可以在屏的规格书中找到，然后在kernel/drivers/gpu/drm/panel/panel-simple.c的panel_simple_probe中初始化了获取时序的函数。
static int panel_simple_probe(struct device *dev, const struct panel_desc *desc)
{
...
panel->base.funcs = &panel_simple_funcs;
...
}
...
static const struct drm_panel_funcs panel_simple_funcs = {
.loader_protect = panel_simple_loader_protect,
.disable = panel_simple_disable,
.unprepare = panel_simple_unprepare,
.prepare = panel_simple_prepare,
.enable = panel_simple_enable,
.get_modes = panel_simple_get_modes,
.get_timings = panel_simple_get_timings,
};
...
该函数在kernel/drivers/gpu/drm/panel/panel-simple.c中定义：
static int panel_simple_get_timings(struct drm_panel *panel, unsigned int num_timings, struct display_timing *timings)
{
struct panel_simple *p = to_panel_simple(panel);
unsigned int i;
if (p->desc->num_timings < num_timings)
num_timings = p->desc->num_timings;
if (timings)
for (i = 0; i < num_timings; i++)
timings[i] = p->desc->timings[i];
return p->desc->num_timings;
}
三、EDP配置
3.1 引脚配置
ROC-RK3568-PC的SDK有EDP的DTS文件：kernel/arch/arm64/boot/dts/rockchip/rk3568-firefly-roc-pc-edp_M156X40.dts，从该文件中我们可以看到以下语句：
edp_panel: edp-panel {
compatible = "simple-panel";
status = "okay";
power-supply = <&vcc3v3_lcd_edp>;
enable-gpios = <&gpio3 RK_PC3 GPIO_ACTIVE_HIGH>;
//bus-format = ;
backlight = <&backlight>;
...
ports {
panel_in_edp: endpoint {
remote-endpoint = <&edp_out_panel>;
};
};
};
...
};
&edp {
status = "okay";
hpd-gpios = <&gpio0 RK_PC2 GPIO_ACTIVE_HIGH>;
force-hpd;
ports {
edp_out: port@1 {
reg = <1>;
#address-cells = <1>;
#size-cells = <0>;
edp_out_panel: endpoint@0 {
reg = <0>;
remote-endpoint = <&panel_in_edp>;
};
};
};
};
这里定义了LCD的电源控制引脚：
| NAME | GPIO | GPIO_ACTIVE |
|---|---|---|
| BL_EN | GPIO3_C3 | GPIO_ACTIVE_HIGH |
| EDP_HPD | GPIO0_C2 | GPIO_ACTIVE_HIGH |
3.2 EDP背光配置
因为背光接口是公用的，所以可以参考上述MIPI的配置方法。
4.3.3. EDP显示时序配置
不同于MIPI屏，EDP屏对上下电时序没有那么高的要求，当然还是要看调试屏幕的上下电时序图来配置：
edp_panel: edp-panel {
compatible = "simple-panel";
status = "okay";
...
display-timings {
native-mode = <&timing0>;
timing0: timing0 {
clock-frequency = <140000000>;
hactive = <1920>;
vactive = <1080>;
hfront-porch = <40>;
hsync-len = <40>;
hback-porch = <80>;
vfront-porch = <16>;
vsync-len = <8>;
vback-porch = <16>;
hsync-active = <0>;
vsync-active = <0>;
de-active = <0>;
pixelclk-active = <0>;
};
};
...
};
display-timings同样在kernel/drivers/gpu/drm/panel/panel-simple.c中使用到：
static int panel_simple_get_timings(struct drm_panel *panel, unsigned int num_timings, struct display_timing *timings)
{
struct panel_simple *p = to_panel_simple(panel);
unsigned int i;
if (p->desc->num_timings < num_timings)
num_timings = p->desc->num_timings;
if (timings)
for (i = 0; i < num_timings; i++)
timings[i] = p->desc->timings[i];
return p->desc->num_timings;
}