华为鲲鹏云（arm64）搭建Harbor

环境介绍（因已离开原公司，文中涉及镜像已失效，请参考鲲鹏文档自行编译，后期会想办法存放在公共仓库中）

由于国产化趋势大环境，需要在鲲鹏云上部署Harbor，但是默认镜像并不支持arm架构，本文提供已经编译好所需的10个arm镜像，目前版本为1.9.1，后续有时间时在考虑升级新的版本，如需自己编译可参考鲲鹏官方文档：http://ic-openlabs.huawei.com/openlab/#/knowledgebasequery?task_id=R1S1584D00303813520191125094129756587245

一、安装Docker-ce、Docker-compose（略）

需要提前安装好Docker-ce、Docker-compose，这里就不介绍了，网上很多，yum安装就行

二、搭建Harbor

1、下载源码或者离线安装包（offline离线安装包未测试过，理论上也是可行的，注意对应版本）

[root@localhost ~]# wget https://github.com/goharbor/harbor/archive/v1.9.1.tar.gz

2、拉取镜像（共10个）

[root@localhost ~]# docker pull harbor.cq-mlkj.com/goharbor/harbor-core:v1.9.1
[root@localhost ~]# docker pull harbor.cq-mlkj.com/goharbor/harbor-db:v1.9.1
[root@localhost ~]# docker pull harbor.cq-mlkj.com/goharbor/harbor-jobservice:v1.9.1
[root@localhost ~]# docker pull harbor.cq-mlkj.com/goharbor/harbor-log:v1.9.1
[root@localhost ~]# docker pull harbor.cq-mlkj.com/goharbor/harbor-portal:v1.9.1
[root@localhost ~]# docker pull harbor.cq-mlkj.com/goharbor/harbor-registryctl:v1.9.1
[root@localhost ~]# docker pull harbor.cq-mlkj.com/goharbor/nginx-photon:v1.9.1
[root@localhost ~]# docker pull harbor.cq-mlkj.com/goharbor/prepare:v1.9.1
[root@localhost ~]# docker pull harbor.cq-mlkj.com/goharbor/redis-photon:v1.9.1
[root@localhost ~]# docker pull harbor.cq-mlkj.com/goharbor/registry-photon:v2.7.1-v1.9.1

3、更改镜像tag去掉域名

[root@localhost ~]# docker tag harbor.cq-mlkj.com/goharbor/harbor-core:v1.9.1 goharbor/harbor-core:v1.9.1
[root@localhost ~]# docker tag harbor.cq-mlkj.com/goharbor/harbor-db:v1.9.1 goharbor/harbor-db:v1.9.1
[root@localhost ~]# docker tag harbor.cq-mlkj.com/goharbor/harbor-jobservice:v1.9.1 goharbor/harbor-jobservice:v1.9.1
[root@localhost ~]# docker tag harbor.cq-mlkj.com/goharbor/harbor-log:v1.9.1 goharbor/harbor-log:v1.9.1
[root@localhost ~]# docker tag harbor.cq-mlkj.com/goharbor/harbor-portal:v1.9.1 goharbor/harbor-portal:v1.9.1
[root@localhost ~]# docker tag harbor.cq-mlkj.com/goharbor/harbor-registryctl:v1.9.1 goharbor/harbor-registryctl:v1.9.1
[root@localhost ~]# docker tag harbor.cq-mlkj.com/goharbor/nginx-photon:v1.9.1 goharbor/nginx-photon:v1.9.1
[root@localhost ~]# docker tag harbor.cq-mlkj.com/goharbor/prepare:v1.9.1 goharbor/prepare:v1.9.1
[root@localhost ~]# docker tag harbor.cq-mlkj.com/goharbor/redis-photon:v1.9.1 goharbor/redis-photon:v1.9.1
[root@localhost ~]# docker tag harbor.cq-mlkj.com/goharbor/registry-photon:v2.7.1-v1.9.1 goharbor/registry-photon:v2.7.1-v1.9.1

4、解压源码（离线版步骤一样，只是文件名和路径可能不同）

[root@localhost ~]# tar -zxvf v1.9.1.tar.gz && cd harbor-1.9.1/make

5、修改harbor.yml（自行修改端口，https，账号和密码等配置信息）

[root@localhost ~]# vi harbor.yml

6、执行install.sh安装

[root@localhost ~]# ./install.sh

7、验证

[root@localhost ~]# docker-compose ps

8、浏览器访问配置的端口测试，默认帐号密码：amdin/Harbor12345

9、停止和启动

[root@localhost ~]# docker-compose stop
[root@localhost ~]# docker-compose start

---- 结束