ESP32 wifi视频/图传

ESP32 wifi视频/图传

---

一、安装Arduino

1.1 软件下载

https://arduino.me/download，下载安装1.8.19版本（主要2.xxx不稳定）

1.2 按照教程安装

https://randomnerdtutorials.com/installing-the-esp32-board-in-arduino-ide-mac-and-linux-instructions/
注意添加ESP32 (by Espressif System)下载版本2.0.2（可能要），及板子的一些Flash(80m)、PartitionScheme(huge)、波特率(115200)都要选对应的

1.3 烧录注意事项

板子要5V供电，IO0和GND短路为下载烧写模式，断开是运行模式，conecting后出现下划线就reset一下

二、实验

2.1 代码

https://gitcode.net/mirrors/yoursunny/esp32cam?utm_source=csdn_github_accelerator

2.2 主程序代码

#include 
#include 
#include 

const char* WIFI_SSID = "***";  // 改成自己的wifi名称
const char* WIFI_PASS = "***";  // 改成自己的wifi密码

WebServer server(80);

static auto loRes = esp32cam::Resolution::find(320, 240);
static auto hiRes = esp32cam::Resolution::find(800, 600);

void handleBmp()
{
  if (!esp32cam::Camera.changeResolution(loRes)) {
    Serial.println("SET-LO-RES FAIL");
  }

  auto frame = esp32cam::capture();
  if (frame == nullptr) {
    Serial.println("CAPTURE FAIL");
    server.send(503, "", "");
    return;
  }
  Serial.printf("CAPTURE OK %dx%d %db\n", frame->getWidth(), frame->getHeight(),
                static_cast<int>(frame->size()));

  if (!frame->toBmp()) {
    Serial.println("CONVERT FAIL");
    server.send(503, "", "");
    return;
  }
  Serial.printf("CONVERT OK %dx%d %db\n", frame->getWidth(), frame->getHeight(),
                static_cast<int>(frame->size()));

  server.setContentLength(frame->size());
  server.send(200, "image/bmp");
  WiFiClient client = server.client();
  frame->writeTo(client);
}

void serveJpg()
{
  auto frame = esp32cam::capture();
  if (frame == nullptr) {
    Serial.println("CAPTURE FAIL");
    server.send(503, "", "");
    return;
  }
  Serial.printf("CAPTURE OK %dx%d %db\n", frame->getWidth(), frame->getHeight(),
                static_cast<int>(frame->size()));

  server.setContentLength(frame->size());
  server.send(200, "image/jpeg");
  WiFiClient client = server.client();
  frame->writeTo(client);
}

void handleJpgLo()
{
  if (!esp32cam::Camera.changeResolution(loRes)) {
    Serial.println("SET-LO-RES FAIL");
  }
  serveJpg();
}

void handleJpgHi()
{
  if (!esp32cam::Camera.changeResolution(hiRes)) {
    Serial.println("SET-HI-RES FAIL");
  }
  serveJpg();
}

void handleJpg()
{
  server.sendHeader("Location", "/cam-hi.jpg");
  server.send(302, "", "");
}

void handleMjpeg()
{
  if (!esp32cam::Camera.changeResolution(hiRes)) {
    Serial.println("SET-HI-RES FAIL");
  }

  Serial.println("STREAM BEGIN");
  WiFiClient client = server.client();
  auto startTime = millis();
  int res = esp32cam::Camera.streamMjpeg(client);
  if (res <= 0) {
    Serial.printf("STREAM ERROR %d\n", res);
    return;
  }
  auto duration = millis() - startTime;
  Serial.printf("STREAM END %dfrm %0.2ffps\n", res, 1000.0 * res / duration);
}

void setup()
{
  Serial.begin(115200);
  Serial.println();

  {
    using namespace esp32cam;
    Config cfg;
    cfg.setPins(pins::AiThinker);
    cfg.setResolution(hiRes);
    cfg.setBufferCount(2);
    cfg.setJpeg(80);

    bool ok = Camera.begin(cfg);
    Serial.println(ok ? "CAMERA OK" : "CAMERA FAIL");
  }

  WiFi.persistent(false);
  WiFi.mode(WIFI_STA);
  WiFi.begin(WIFI_SSID, WIFI_PASS);
  while (WiFi.status() != WL_CONNECTED) {
    delay(500);
  }

  Serial.print("http://");
  Serial.println(WiFi.localIP());
  Serial.println("  /cam.bmp");
  Serial.println("  /cam-lo.jpg");
  Serial.println("  /cam-hi.jpg");
  Serial.println("  /cam.mjpeg");

  server.on("/cam.bmp", handleBmp);
  server.on("/cam-lo.jpg", handleJpgLo);
  server.on("/cam-hi.jpg", handleJpgHi);
  server.on("/cam.jpg", handleJpg);
  server.on("/cam.mjpeg", handleMjpeg);

  server.begin();
}

void loop()
{
  server.handleClient();
}```



# 三、IP访问
## 3.1 路由器设置
将路由器和摄像头IP端口固定
## 3.2 摄像头访问地址
Arduino的串口上会返回摄像头的ip地址，在同一局域网下浏览器中输入地址加想看的图片/视频后缀，如http://192.168.1.240/cam.mjpeg即可