ARM--day4(电灯实验、分析RCC、GPIO控制器，PMOS管、NMOS管的基本原理)
电灯实验代码：
.text
.global _start
_start:
/**********LED1点灯**************/
RCC_INIT:
@1.使能GPIOE组控制器，通过RCC_AHB4ENSETR寄存器设置第［5:4］位写１---->0x50000A28[4]=1
ldr r0,=0x50000A28
ldr r1,[r0]
orr r1,#(0x3 << 4) @使能GPIOE和GPIOF组
str r1,[r0]
LED1_INIT:
@1.设署PE10引脚为输出模式，通过CPTOE MODR寄在器设詈第[21:20]位写01 ==>0x50006000[21:20]= 01
ldr r0,=0x50006000
ldr r1,[r0]
bic r1,#(0x3<<20)
orr r1,#(0x1<<20)
str r1,[r0]
@2.设置GPIO引脚为推挽输出类型,通过GPIOE_OTYPER寄存器设置第[10]位写О--->0x50006004[10]=0
ldr r0,=0x50006004
ldr r1,[r0]
bic r1,#(0x1<<10)
str r1,[r0]
@3.设置PE10引脚为低速输出，通过GPIOE_OSPEEDRE寄存器第[21:20]位写00--->0x50006008[21:20]=00
ldr r0,=0x50006008
ldr r1,[r0]
bic r1,#(0x3<<20)
str r1,[r0]
@4.设置PE10引脚禁止上下拉电阻,通过cPIOE_PUPDR寄存器设置第[21:20]位写00--->0x5000600c[21:20]=00
ldr r0,=0x5000600c
ldr r1,[r0]
bic r1,#(0x3<<20)
str r1,[r0]
LED2_INIT:
@1.设署PF10引脚为输出模式，通过CPTOF MODR寄在器设詈第[21:201位写01 ==>0x50007000[21:20]= 01
ldr r0,=0x50007000
ldr r1,[r0]
bic r1,#(0x3<<20)
orr r1,#(0x1<<20)
str r1,[r0]
@2.设置PF10引脚为推挽输出类型,通过GPIOF_OTYPER寄存器设置第[10]位写О--->0x50007004[10]=0
ldr r0,=0x50007004
ldr r1,[r0]
bic r1,#(0x1<<10)
str r1,[r0]
@3.设置PF10引脚为低速输出，通过GPIOF_OSPEEDRE寄存器第[21:20]位写00--->0x50007008[21:20]=00
ldr r0,=0x50007008
ldr r1,[r0]
bic r1,#(0x3<<20)
str r1,[r0]
@4.设置PF10引脚禁止上下拉电阻,通GPIOF_PUPDR寄存器设置第[21:20]位写00--->0x5000700c[21:20]=00
ldr r0,=0x5000700c
ldr r1,[r0]
bic r1,#(0x3<<20)
str r1,[r0]
LED3_INIT:
@1.设署PE8引脚为输出模式，通过GPTOE MODR寄在器设詈第[17:16]位写01 ==>0x50006000[21:20]= 01
ldr r0,=0x50006000
ldr r1,[r0]
bic r1,#(0x3<<16)
orr r1,#(0x1<<16)
str r1,[r0]
@2.设置GPIO引脚为推挽输出类型,通过GPIOE_OTYPER寄存器设置第[10]位写О--->0x50006004[8]=0
ldr r0,=0x50006004
ldr r1,[r0]
bic r1,#(0x1<<8)
str r1,[r0]
@3.设置PE8引脚为低速输出，通过GPIOE_OSPEEDRE寄存器第[17:16]位写00--->0x50006008[17:16]=00
ldr r0,=0x50006008
ldr r1,[r0]
bic r1,#(0x3<<16)
str r1,[r0]
@4.设置PE8引脚禁止上下拉电阻,通过GPIOE_PUPDR寄存器设置第[17:16]位写00--->0x5000600c[17:16]=00
ldr r0,=0x5000600c
ldr r1,[r0]
bic r1,#(0x3<<16)
str r1,[r0]
loop:
bl LED1_ON
bl delay_1s
bl LED1_OFF
bl delay_1s
bl LED2_ON
bl delay_1s
bl LED2_OFF
bl delay_1s
bl LED3_ON
bl delay_1s
bl LED3_OFF
bl delay_1s
b loop
LED1_ON:
@1.设置PE10引脚输出高电平,通过GPIoE_ODR寄存器设置第〔10]位写1---> 0x50006014[10]=1
ldr r0,=0x50006014
ldr r1,[r0]
orr r1,#(0x1<<10)
str r1,[r0]
mov pc,lr
LED1_OFF:
@1.设置PE10引脚输出低电平---> 0x50006014[10]=0
ldr r0,=0x50006014
ldr r1,[r0]
bic r1,#(0x1<<10)
str r1,[r0]
mov pc,lr
LED2_ON:
@1.设置PE10引脚输出高电平,通过GPIoE_ODR寄存器设置第〔10]位写1---> 0x50006014[10]=1
ldr r0,=0x50007014
ldr r1,[r0]
orr r1,#(0x1<<10)
str r1,[r0]
mov pc,lr
LED2_OFF:
@1.设置PE10引脚输出低电平---> 0x50006014[10]=0
ldr r0,=0x50007014
ldr r1,[r0]
bic r1,#(0x1<<10)
str r1,[r0]
mov pc,lr
LED3_ON:
@1.设置PF10引脚输出高电平,通过GPIOF_ODR寄存器设置第〔10]位写1---> 0x50006014[10]=1
ldr r0,=0x50006014
ldr r1,[r0]
orr r1,#(0x1<<8)
str r1,[r0]
mov pc,lr
LED3_OFF:
@1.设置PE8引脚输出低电平---> 0x50006014[8]=0
ldr r0,=0x50006014
ldr r1,[r0]
bic r1,#(0x1<<8)
str r1,[r0]
mov pc,lr
@ 大概1s的延时函数
delay_1s:
mov r3, #0x10000000
mm: @mm是一个标签
cmp r3, #0
subne r3, r3, #1
bne mm
mov pc, lr
.end