触摸TP,gt9xx调试分享
板子：rk3568
平台：android11
1.添加驱动
驱动文件列表：
-rw-rw-r-- 1 vtlk vtlk 17979 10月 20 14:04 goodix_tool.c
-rw-rw-r-- 1 vtlk vtlk 965 7月 11 16:52 'GT9110P(2020)V71_Config_20201028_170326.cfg'
-rw-rw-r-- 1 vtlk vtlk 929 7月 11 16:52 GT9110P_Config_20160217_1526_2048_97.cfg
-rw-rw-r-- 1 vtlk vtlk 929 7月 11 16:52 GT9271_Config_20170526.cfg
-rw-rw-r-- 1 vtlk vtlk 87561 10月 20 15:30 gt9xx.c
-rw-rw-r-- 1 vtlk vtlk 1853 7月 11 16:52 gt9xx_cfg.h
-rw-rw-r-- 1 vtlk vtlk 224220 10月 20 11:38 gt9xx_firmware.h
-rw-rw-r-- 1 vtlk vtlk 14656 10月 20 15:13 gt9xx.h
-rw-rw-r-- 1 vtlk vtlk 106042 10月 20 11:38 gt9xx_update.c
-rw-rw-r-- 1 vtlk vtlk 929 7月 11 16:52 HLS-0102-1398V1-1060-GT911_Config_20201204_V66.cfg
-rw-rw-r-- 1 vtlk vtlk 152 10月 20 15:45 Makefile
-rw-rw-r-- 1 vtlk vtlk 929 7月 11 16:52 WGJ10162B_GT9271_1060_Config_20140821_1341110X42.cfg
-rw-rw-r-- 1 vtlk vtlk 929 7月 11 16:52 WGJ10162_GT9271_Config_20140820_182456.cfg
-rw-rw-r-- 1 vtlk vtlk 1366 7月 11 16:52 WGJ10187_GT910_Config_20140623_104014_0X41.cfg
-rw-rw-r-- 1 vtlk vtlk 929 7月 11 16:52 WGJ10187_GT9271_Config_20140623_104014_0X41.cfg
-rwxrwxr-x 1 vtlk vtlk 929 7月 11 16:52 WGJ89006B_GT911_Config_20140625_085816_0X43.cfg
-rw-rw-r-- 1 vtlk vtlk 929 7月 11 16:52 WGJ89006B_GT9271_Config_20140625_085816_0X41.cfg
首先是设备树配置：
&i2c1 {
status = "okay";
gt928:gt928@14 {
compatible = "goodix,gt9xx";//"goodix,gt928";
status = "okay";
reg = <0x14>;
pinctrl-names = "default";
pinctrl-0 = <>928_reset_pin >928_int_pin>;
interrupt-parent = <&gpio0>;
interrupts = <RK_PB5 IRQ_TYPE_EDGE_FALLING>;
touch-gpio = <&gpio0 RK_PB5 0>;
reset-gpio = <&gpio0 RK_PB6 0>;
max-x = <800>;
max-y = <1280>;
tp-size = <928>;
};
};
这里的touch-gpio,reset-gpio,max-x,max-y,tp-size是根据probe代码里获取设备树属性来确定的，drivers/input/touchscreen/gt9xx/gt9xx.c中probe部分代码如下:
static int goodix_ts_probe(struct i2c_client *client, const struct i2c_device_id *id)
{
s32 ret = -1;
struct goodix_ts_data *ts;
u16 version_info;
struct device_node *np = client->dev.of_node;
enum of_gpio_flags rst_flags, pwr_flags;
u32 val;
...
if (of_property_read_u32(np, "tp-size", &val)) {
dev_err(&client->dev, "no max-x defined\n");
return -EINVAL;
}
ts->tp_regulator = devm_regulator_get(&client->dev, "tp");
if (IS_ERR(ts->tp_regulator)) {
dev_err(&client->dev, "failed to get regulator, %ld\n",
PTR_ERR(ts->tp_regulator));
return PTR_ERR(ts->tp_regulator);
}
ret = regulator_enable(ts->tp_regulator);
if (ret < 0)
GTP_ERROR("failed to enable tp regulator\n");
msleep(20);
ts->irq_pin = of_get_named_gpio_flags(np, "touch-gpio", 0, (enum of_gpio_flags *)(&ts->irq_flags));
ts->rst_pin = of_get_named_gpio_flags(np, "reset-gpio", 0, &rst_flags);
ts->pwr_pin = of_get_named_gpio_flags(np, "power-gpio", 0, &pwr_flags);
//ts->tp_select_pin = of_get_named_gpio_flags(np, "tp-select-gpio", 0, &tp_select_flags);
if (of_property_read_u32(np, "max-x", &val)) {
dev_err(&client->dev, "no max-x defined\n");
return -EINVAL;
}
//ts->abs_x_max = val;
if (of_property_read_u32(np, "max-y", &val)) {
dev_err(&client->dev, "no max-y defined\n");
return -EINVAL;
}
//ts->abs_y_max = val;
if (of_property_read_u32(np, "configfile-num", &val)) {
ts->cfg_file_num = 0;
} else {
ts->cfg_file_num = val;
}
ts->pendown =PEN_RELEASE;
ts->client = client;
...
if (of_property_read_bool(np, "wakeup-source"))
{
device_init_wakeup(&client->dev, 1);
enable_irq_wake(ts->irq);
}
...
}
这里的max-x，max-y是屏幕尺寸对应触摸最大范围；touch-gpio,reset-gpio,分别表示对应的中断检测脚和复位脚；tp-size对应的是正反转的，我这里是直接在gt9xx.c修改全局变量所以tp-size根据需要来配置就可以了；
其次就是在deconfig文件中添加编译
CONFIG_TOUCHSCREEN_GT9XX=y
编译好后download到板子上，成功后的log:
[ 1.129428] goodix_ts_probe() start
[ 1.129483] Goodix-TS 1-0014: 1-0014 supply tp not found, using dummy regulator
[ 1.129565] Goodix-TS 1-0014: Linked as a consumer to regulator.0
[ 1.320703] input: goodix-ts as /devices/platform/fe5a0000.i2c/i2c-1/1-0014/input/input1
被注册成输入设备1了
或者使用命令 adb shell getevent 打开输入检测，触摸屏幕会在终端上打印触摸坐标信息，如：
vtlk:~$adb shell getevent
add device 1: /dev/input/event1
name: "goodix-ts"
add device 2: /dev/input/event3
name: "gpio-keys"
add device 3: /dev/input/event0
name: "rk805 pwrkey"
add device 4: /dev/input/event2
name: "adc-keys"
add device 5: /dev/input/event4
name: "rk-headset"
/dev/input/event1: 0001 014a 00000001
/dev/input/event1: 0003 0035 000002e8
/dev/input/event1: 0003 0036 0000021f
/dev/input/event1: 0003 0030 00000020
/dev/input/event1: 0003 0032 00000020
/dev/input/event1: 0003 0039 00000000
/dev/input/event1: 0000 0002 00000000
/dev/input/event1: 0000 0000 00000000
/dev/input/event1: 0003 0035 000002e8
2.问题
对应的x和y轴的相反，可以修改drivers/input/touchscreen/gt9xx/gt9xx.c中的全局变量：
static u8 gtp_change_x2y = FALSE;
如果只是x左右相反或折y方向的上下相反可以修改如下量个变量
static u8 gtp_x_reverse = TRUE;
static u8 gtp_y_reverse = TRUE;