艾美加ix2 uboot信息(debian暂不会安装)

ttl接线

1     3.3v

2    RXD

3   GND

4   Txd



__ __ _ _

        |  \/  | __ _ _ ____  _____| | |

        | |\/| |/ _` | '__\ \ / / _ \ | |

        | |  | | (_| | |  \ V /  __/ | |

        |_|  |_|\__,_|_|    \_/ \___|_|_|

_  _    ____              _

| | | |  | __ )  ___  ___ | |_

| | | |___|  _ \ / _ \ / _ \| __|

| |_| |___| |_) | (_) | (_) | |_

\___/    |____/ \___/ \___/ \__|  ** ix2-nand ** ** uboot_ver:0.0.8 **

** MARVELL BOARD: DB-88F6282A-BP LE

U-Boot 1.1.4 (Oct 28 2011 - 15:19:29) Marvell version: 3.6.1 - EMC

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006CFB00

Soc: 88F6282 A1 CPU running @ 1600Mhz L2 running @ 533Mhz

SysClock = 533Mhz , TClock = 200Mhz

DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7

DRAM CS[0] base 0x00000000  size 256MB

DRAM Total size 256MB  16bit width

Addresses 8M - 0M are saved for the U-Boot usage.

Mem malloc Initialization (8M - 7M): Done

NAND:1024 MB

Found ADT7473, program PWM1 ... OK

Flash:  0 kB

Marvell Serial ATA Adapter

Integrated Sata device found

CPU : Marvell Feroceon (Rev 1)

Found kernel at 0x100000

Found initrd at 0x400000

Streaming disabled

Write allocate disabled

USB 0: host mode

PEX 0: interface detected no Link.

PEX 1: interface detected no Link.

Net:  egiga0 [PRIME]

Hit any key to stop autoboot:  0

NAND read: device 0 offset 0x100000, size 0x300000

Reading data from 0x3ff800 -- 100% complete.

3145728 bytes read: OK

NAND read: device 0 offset 0x400000, size 0x400000

Reading data from 0x7ff800 -- 100% complete.

4194304 bytes read: OK

## Booting image at 00040000 ...

  Image Name:  Linux-2.6.31.8

  Created:      2019-06-17  12:13:03 UTC

  Image Type:  ARM Linux Kernel Image (uncompressed)

  Data Size:    2502832 Bytes =  2.4 MB

  Load Address: 00008000

  Entry Point:  00008000

  Verifying Checksum ... OK

OK

## Loading Ramdisk Image at 00900000 ...

  Image Name: 

  Created:      2019-06-17  12:44:09 UTC

  Image Type:  ARM Linux RAMDisk Image (bzip2 compressed)

  Data Size:    2982113 Bytes =  2.8 MB

  Load Address: 00000000

  Entry Point:  00000000

  Verifying Checksum ... OK

Starting kernel ...

Linux version 2.6.31.8 ([email protected]) (gcc version 4.7.2 (crosstool-NG 1.20.0) ) Mon Jun 17 08:12:59 EDT 2019 v0.0.9 Mon Jun 17 08:12:59 EDT 2019

CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977

CPU: VIVT data cache, VIVT instruction cache

Machine: Feroceon-KW

Using UBoot passing parameters structure

Memory policy: ECC disabled, Data cache writeback

Built 1 zonelists in Zone order, mobility grouping off.  Total pages: 64960

Kernel command line: console=ttyS0,115200 root=/dev/ram0 :::DB88FXX81:eth0:none mtdparts=nand_mtd:0x80000@0(uboot),0x20000@0xa0000(env),0x20000@0xc0000(env2),0x300000@0x100000(uImage),0x400000@0x400000(initrd),0x3f800000@0x800000(boot),1024m@0x0(flash)

PID hash table entries: 1024 (order: 10, 4096 bytes)

Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)

Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)

Memory: 256MB = 256MB total

Memory: 244352KB available (4592K code, 365K data, 136K init, 0K highmem)

Hierarchical RCU implementation.

NR_IRQS:128

Console: colour dummy device 80x30

Calibrating delay loop... 1589.24 BogoMIPS (lpj=7946240)

Security Framework initialized

Mount-cache hash table entries: 512

CPU: Testing write buffer coherency: ok

xor: measuring software checksum speed

  arm4regs  :  1447.200 MB/sec

  8regs    :  867.600 MB/sec

  32regs    :  1120.400 MB/sec

xor: using function: arm4regs (1447.200 MB/sec)

NET: Registered protocol family 16

Feroceon L2: Enabling L2

Feroceon L2: Cache support initialised.

CPU Interface

-------------

SDRAM_CS0 ....base 00000000, size 256MB

SDRAM_CS1 ....disable

SDRAM_CS2 ....disable

SDRAM_CS3 ....disable

PEX0_MEM ....base e0000000, size 128MB

PEX0_IO ....base f2000000, size  1MB

PEX1_MEM ....base e8000000, size 128MB

PEX1_IO ....base f2100000, size  1MB

INTER_REGS ....base f1000000, size  1MB

NFLASH_CS ....base fa000000, size  2MB

SPI_CS ....base f4000000, size  16MB

BOOT_ROM_CS ....no such

DEV_BOOTCS ....no such

CRYPT_ENG ....base f0000000, size  2MB

  Marvell Development Board (LSP Version KW_LSP_5.1.3_patch25)-- DB-88F6282A-BP  Soc: 88F6282 A1 LE

Detected Tclk 200000000 and SysClk 533333333

MV Buttons Device Load

Marvell USB EHCI Host controller #0: c8040740

PEX0 interface detected no Link.

PEX1 interface detected no Link.

PCI: bus0: Fast back to back transfers enabled

PCI: bus1: Fast back to back transfers enabled

bio: create slab at 0

SCSI subsystem initialized

usbcore: registered new interface driver usbfs

usbcore: registered new interface driver hub

usbcore: registered new device driver usb

raid6: int32x1    125 MB/s

raid6: int32x2    157 MB/s

raid6: int32x4    162 MB/s

raid6: int32x8    159 MB/s

raid6: using algorithm int32x4 (162 MB/s)

NET: Registered protocol family 2

IP route cache hash table entries: 2048 (order: 1, 8192 bytes)

TCP established hash table entries: 8192 (order: 4, 65536 bytes)

TCP bind hash table entries: 8192 (order: 3, 32768 bytes)

TCP: Hash tables configured (established 8192 bind 8192)

TCP reno registered

NET: Registered protocol family 1

Trying to unpack rootfs image as initramfs...

rootfs image is not initramfs (no cpio magic); looks like an initrd

Freeing initrd memory: 2912K

rtc mv_rtc: rtc core: registered kw-rtc as rtc0

RTC registered

XOR registered 4 channels

XOR 2nd invalidate WA enabled

cesadev_init(c000ed58)

mvCesaInit: sessions=640, queue=64, pSram=f0000000

MV Buttons Driver Load

VFS: Disk quotas dquot_6.5.2

Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)

squashfs: version 4.0 (2009/01/31) Phillip Lougher

Registering unionfs 2.5.11 (for 2.6.31.14)

Installing knfsd (copyright (C) 1996 [email protected]).

msgmni has been set to 483

alg: No test for cipher_null (cipher_null-generic)

alg: No test for ecb(cipher_null) (ecb-cipher_null)

alg: No test for digest_null (digest_null-generic)

alg: No test for compress_null (compress_null-generic)

alg: No test for stdrng (krng)

alg: No test for hmac(digest_null) (hmac(digest_null-generic))

async_tx: api initialized (sync-only)

Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)

io scheduler noop registered

io scheduler anticipatory registered (default)

Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled

serial8250.0: ttyS0 at MMIO 0xf1012100 (irq = 34) is a 16550A

console [ttyS0] enabled

brd: module loaded

loop: module loaded

Integrated Sata device found

IRQ 21/mvSata: IRQF_DISABLED is not guaranteed on shared IRQs

scsi0 : Marvell SCSI to SATA adapter

scsi1 : Marvell SCSI to SATA adapter

Loading Marvell Ethernet Driver:

  o Cached descriptors in DRAM

  o DRAM SW cache-coherency

  o 2 Giga ports supported

  o Single RX Queue support - ETH_DEF_RXQ=0

  o Single TX Queue support - ETH_DEF_TXQ=0

  o TCP segmentation offload (TSO) supported

  o Large Receive offload (LRO) supported

  o Receive checksum offload supported

  o Transmit checksum offload supported

  o Proc tool API enabled

  o Rx descripors: q0=256

  o Tx descripors: q0=532

  o Loading network interface(s):

    o register under mv88fx_eth platform

    o eth0, ifindex = 2, GbE port = 0

Warning: Giga 1 is Powered Off

tun: Universal TUN/TAP device driver, 1.6

tun: (C) 1999-2004 Max Krasnyansky

mvSFlashInit ERROR: Unknown SPI flash device!

ERROR: sflash_probe - Failed to initialize the SFlash.Using Hamming 1-bit ECC for NAND device

NAND flash model -> K9K8G08U0D.

NAND device: Manufacturer ID: 0xec, Chip ID: 0xd3 (Samsung NAND 1GiB 3,3V 8-bit)

Scanning device for bad blocks

Bad eraseblock 761 at 0x000005f20000

Bad eraseblock 1390 at 0x00000adc0000

Bad eraseblock 7299 at 0x000039060000

7 cmdlinepart partitions found on MTD device nand_mtd

Using command line partition definition

Creating 7 MTD partitions on "nand_mtd":

0x000000000000-0x000000080000 : "uboot"

0x0000000a0000-0x0000000c0000 : "env"

0x0000000c0000-0x0000000e0000 : "env2"

0x000000100000-0x000000400000 : "uImage"

0x000000400000-0x000000800000 : "initrd"

0x000000800000-0x000040000000 : "boot"

0x000000000000-0x000040000000 : "flash"

ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver

ehci_marvell ehci_marvell.70059: Marvell Orion EHCI

ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1

ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100

ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00

usb usb1: configuration #1 chosen from 1 choice

hub 1-0:1.0: USB hub found

hub 1-0:1.0: 1 port detected

ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver

uhci_hcd: USB Universal Host Controller Interface driver

usbcore: registered new interface driver usblp

Initializing USB Mass Storage driver...

usbcore: registered new interface driver usb-storage

USB Mass Storage support registered.

usbcore: registered new interface driver ums-datafab

usbcore: registered new interface driver ums-freecom

usbcore: registered new interface driver ums-jumpshot

usbcore: registered new interface driver ums-sddr09

usbcore: registered new interface driver ums-sddr55

usbcore: registered new interface driver ums-usbat

mice: PS/2 mouse device common for all mice

i2c /dev entries driver

adt7473 0-002e: adt7473 chip found

iBoard_model 2

md: linear personality registered for level -1

md: raid0 personality registered for level 0

md: raid1 personality registered for level 1

md: raid10 personality registered for level 10

md: raid6 personality registered for level 6

md: raid5 personality registered for level 5

md: raid4 personality registered for level 4

device-mapper: uevent: version 1.0.3

device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: [email protected]

dm_crypt using the OCF package.

usbcore: registered new interface driver hiddev

usbcore: registered new interface driver usbhid

usbhid: v2.6:USB HID core driver

TCP cubic registered

NET: Registered protocol family 17

NET: Registered protocol family 5

RPC: Registered udp transport module.

RPC: Registered tcp transport module.

rtc mv_rtc: setting system clock to 2021-01-24 00:22:07 UTC (1611447727)

md: Waiting for all devices to be available before autodetect

md: If you don't use raid, use raid=noautodetect

md: Autodetecting RAID arrays.

md: Scanned 0 and added 0 devices.

md: autorun ...

md: ... autorun DONE.

RAMDISK: bzip2 image found at block 0

EXT2-fs warning: checktime reached, running e2fsck is recommended

VFS: Mounted root (ext2 filesystem) on device 1:0.

Looking for shell in cmdline: console=ttyS0,115200 root=/dev/ram0 :::DB88FXX81:eth0:none mtdparts=nand_mtd:0x80000@0(uboot),0x20000@0xa0000(env),0x20000@0xc0000(env2),0x300000@0x100000(uImage),0x400000@0x400000(initrd),0x3f800000@0x800000(boot),1024m@0x0(flash)

Make node for mtd devices

cat: can't open '/sys/class/block/sda/removable': No such file or directory

cat: can't open '/sys/class/block/sdb/removable': No such file or directory

FLASH based system detected

Create fw_env.config in /etc

Model name is ix2-ng

UBI: attaching mtd5 to ubi0

UBI: physical eraseblock size:  131072 bytes (128 KiB)

UBI: logical eraseblock size:    129024 bytes

UBI: smallest flash I/O unit:    2048

UBI: sub-page size:              512

UBI: VID header offset:          512 (aligned 512)

UBI: data offset:                2048

UBI: attached mtd5 to ubi0

UBI: MTD device name:            "boot"

UBI: MTD device size:            1016 MiB

UBI: number of good PEBs:        8125

UBI: number of bad PEBs:        3

UBI: max. allowed volumes:      128

UBI: wear-leveling threshold:    4096

UBI: number of internal volumes: 1

UBI: number of user volumes:    1

UBI: available PEBs:            0

UBI: total number of reserved PEBs: 8125

UBI: number of PEBs reserved for bad PEB handling: 81

UBI: max/mean erase counter: 5/4

UBI: image sequence number: 0

UBI: background thread "ubi_bgt0d" started, PID 604

UBI device number 0, total 8125 LEBs (1048320000 bytes, 999.8 MiB), available 0 LEBs (0 bytes), LEB size 129024 bytes (126.0 KiB)

mdadm: No devices to examine

cat: can't open '/sys/class/block///size': No such file or directory

mdadm: No devices to examine

cat: can't open '/sys/class/block///size': No such file or directory

Valid Disk 1 in md0:

Valid Disk 2 in md0:

USB Device node is /dev/sda1

Checking to see the if the reset button is pressed or not

Checking for valid image on system

UBIFS: recovery needed

UBIFS: recovery completed

UBIFS: mounted UBI device 0, volume 0, name "boot"

UBIFS: file system size:  1035159552 bytes (1010898 KiB, 987 MiB, 8023 LEBs)

UBIFS: journal size:      33546240 bytes (32760 KiB, 31 MiB, 260 LEBs)

UBIFS: media format:      w4/r0 (latest is w4/r0)

UBIFS: default compressor: lzo

UBIFS: reserved for root:  4952683 bytes (4836 KiB)

md: md0 stopped.

mdadm: stopped /dev/md0

mdadm: /dev/md0 not identified in config file.

  No volume groups found

Mount BFDlv to /mnt/boot on ix2-ng NAND

e2fsck 1.42.5 (29-Jul-2012)

ext2fs_check_if_mount: Can't check if filesystem is mounted due to missing mtab file while determining whether /dev/md0_vg/BFDlv is mounted.

e2fsck: No such file or directory while trying to open /dev/md0_vg/BFDlv

Possibly non-existent device?

mount: mounting /dev/md0_vg/BFDlv on sysroot/mnt/boot failed: No such file or directory

Copy dev node to /sysroot/dev

Found Valid EMC Image in disk...

Mounting apps image...

Mounting config image...

Check config filesystem

e2fsck 1.42.5 (29-Jul-2012)

ext2fs_check_if_mount: Can't check if filesystem is mounted due to missing mtab file while determining whether /dev/loop1 is mounted.

Copying System.map...

No need to create fw_env.config

No need to create fw_env.config

Constructing root filesystem...

Bootstrapping ...

rootdir=/

table='/usr/local/cfg/device_table.txt'

makedevs: line 42: chown failed for /bin/busybox: Read-only file system

makedevs: line 49: regular file '/usr/share/udhcpc/default.script' does not exist: No such file or directory

makedevs: line 55: Couldnt create node /dev/null: File exists

makedevs: line 56: Couldnt create node /dev/zero: File exists

makedevs: line 58: Couldnt create node /dev/urandom: File exists

makedevs: line 61: Couldnt create node /dev/loop0: File exists

makedevs: line 61: Couldnt create node /dev/loop1: File exists

makedevs: line 61: Couldnt create node /dev/loop2: File exists

makedevs: line 64: Couldnt create node /dev/console: File exists

makedevs: line 66: Couldnt create node /dev/tty2: File exists

makedevs: line 66: Couldnt create node /dev/tty3: File exists

makedevs: line 66: Couldnt create node /dev/tty4: File exists

makedevs: line 71: Couldnt create node /dev/ttyS0: File exists

makedevs: line 71: Couldnt create node /dev/ttyS1: File exists

makedevs: line 86: Couldnt create node /dev/mtd0: File exists

makedevs: line 86: Couldnt create node /dev/mtd1: File exists

makedevs: line 86: Couldnt create node /dev/mtd2: File exists

makedevs: line 86: Couldnt create node /dev/mtd3: File exists

makedevs: line 86: Couldnt create node /dev/mtd4: File exists

makedevs: line 86: Couldnt create node /dev/mtd5: File exists

makedevs: line 123: Couldnt create node /dev/sda: File exists

makedevs: line 124: Couldnt create node /dev/sda1: File exists

makedevs: line 125: Couldnt create node /dev/sdb: File exists

makedevs: line 126: Couldnt create node /dev/sdb1: File exists

makedevs: line 127: Couldnt create node /dev/sdc: File exists

makedevs: line 128: Couldnt create node /dev/sdc1: File exists

makedevs: line 190: Couldnt create node /dev/md0: File exists

makedevs: line 191: Couldnt create node /dev/md1: File exists

warning: failed to read mtab

Loading ext4...

Loading xfs...

SGI XFS with ACLs, security attributes, large block/inode numbers, no debug enabled

SGI XFS Quota Management subsystem

Loading isofs...

Loading udf...

Loading ufsd...

ufsd: module license 'Commercial product' taints kernel.

Disabling lock debugging due to kernel taint

ufsd: driver 8.5 (Jun 17 2019 08:30:02) LBD=ON with delayalloc with ioctl loaded at bf102000

NTFS support included

Hfs+/HfsX support included

Built for: EMC_ix2_2Loading btusb...

Bluetooth: Core ver 2.15

NET: Registered protocol family 31

Bluetooth: HCI device and connection manager initialized

Bluetooth: HCI socket layer initialized

Bluetooth: Generic Bluetooth USB driver ver 0.5

usbcore: registered new interface driver btusb

## Error: "hwdata" not defined

Initialization complete.

Freeing init memory: 136K

INIT: version 2.88 booting

INIT: /etc/inittab[63]: missing action field

Running file /etc/init.d/rcS

Running file /etc/init.d/rc

Running file /etc/rcS.d/S02hostname.sh

Running file /etc/rcS.d/S02mountkernfs.sh

[....] udev requires a kernel >= 2.6.32, not started ... failed!

failed!

Running file /etc/rcS.d/S04mountdevsubfs.sh

Running file /etc/rcS.d/S07hdparm

[....] Setting parameters of disc: (none). ok

Running file /etc/rcS.d/S11hwclock.sh

[info] Setting the system clock.

hwclock: Warning: unrecognized third line in adjtime file

(Expected: `UTC' or `LOCAL' or nothing.)

[info] System Clock set to: Sun Jan 24 00:22:34 UTC 2021.

Running file /etc/rcS.d/S12mtab.sh

Running file /etc/init.d/mountkernfs.sh

Running file /etc/init.d/mountkernfs.sh

Running file /etc/init.d/mountdevsubfs.sh

Running file /etc/init.d/mountdevsubfs.sh

Running file /etc/rcS.d/S30checkfs.sh

[....] Activating lvm and md swap...done.

[....] Checking file systems...fsck 1.42.5 (29-Jul-2012)

done.

Running file /etc/rcS.d/S30procps

[....] Setting kernel variables ...Running file /etc/rcS.d/S35mountall.sh

[....] Mounting local filesystems...done.

[....] Activating swapfile swap...done.

Running file /etc/rcS.d/S36mountall-bootclean.sh

[....] Cleaning up temporary files... /tmp. ok

Running file /etc/rcS.d/S36udev-mtab

dhclient host identical

Running file /etc/rcS.d/S40networking

[....] Configuring network interfaces...done.

Running file /etc/rcS.d/S43rpcbind

[....] Starting rpcbind daemon.... ok

Running file /etc/rcS.d/S44nfs-common

[....] Starting NFS common utilities: statd failed!

Running file /etc/rcS.d/S45mountnfs.sh

Running file /etc/rcS.d/S46mountnfs-bootclean.sh

[....] Cleaning up temporary files.... ok

Running file /etc/rcS.d/S55bootmisc.sh

Running file /etc/rcS.d/S55urandom

INIT: Entering runlevel: 2

Running file /etc/init.d/rc

Running file /etc/rc2.d/S10rsyslog

[....] Starting enhanced syslogd: rsyslogd. ok

Running file /etc/rc2.d/S12dbus

chown: invalid user: `messagebus'

Running file /etc/rc2.d/S20nfs-common

[....] Starting NFS common utilities: statd failed!

Running file /etc/rc2.d/S20nfs-kernel-server

[....] Not starting NFS kernel daemon: no exports. ... (warning).

Running file /etc/rc2.d/S20smartmontools

Running file /etc/rc2.d/S20sysfsutils

[....] Setting sysfs variables.... ok

Running file /etc/rc2.d/S23ntp

[....] Starting NTP server: ntpdRunning file /etc/rc2.d/S25bluetooth

[....] Starting bluetooth: bluetoothd rfcommBluetooth: L2CAP ver 2.13

Bluetooth: L2CAP socket layer initialized

Bluetooth: RFCOMM socket layer initialized

Bluetooth: RFCOMM ver 1.11

. ok

Starting netplugd...

eth0: started

ln: failed to create symbolic link `/etc/samba/smb.conf': File exists

Generating RSA Key...

unknown key type rsa1

Starting sshd: OK

hostnamed begin to start...

Checking Netwrok interface link status...

Warning : Network Link Is Not Available...

## Error: "hwdata" not defined

hostnamed finished

Starting executord - appmd

export proxy environmental variables

Done.

Running file /etc/rc2.d/S99rc.local

Running file /etc/rc2.d/S99rmnologin

Debian GNU/Linux 7 ix2-dl ttyS0

ix2-dl login: ÿ

你可能感兴趣的:(艾美加ix2 uboot信息(debian暂不会安装))