HeartBeat监控springboot服务状态

目录

一、环境准备

二、安装部署

2.1 下载安装包到指定文件夹，并解压

2.2 复制证书文件

2.3 编辑配置文件

2.4 设置模板

2.5 启动服务

2.6 检查es是否收到数据

---

一、环境准备

    部署模式：单节点部署。

    安装包：heartbeat安装包下载地址

二、安装部署

2.1 下载安装包到指定文件夹，并解压

# 进入安装目录
cd /opt/module
# 解压安装包
tar xf heartbeat-8.11.0.tar.gz

2.2 复制证书文件

# 进入配置文件目录
cd heartbeat-8.11.0/config
# 创建证书文件夹
mkdir certs
# 将es的证书文件复制到certs文件夹下
cp /opt/module/elasticsearch-8.11.0/config/certs/* certs/

2.3 编辑配置文件

vim heartbeat.yml

heartbeat.config.monitors:
  # Directory + glob pattern to search for configuration files
  path: ${path.config}/monitors.d/*.yml
  # If enabled, heartbeat will periodically check the config.monitors path for changes
  reload.enabled: false
  # How often to check for changes
  reload.period: 5s

# Configure monitors inline
heartbeat.monitors:
- type: http
  # Set enabled to true (or delete the following line) to enable this monitor
  enabled: true
  # ID used to uniquely identify this monitor in Elasticsearch even if the config changes
  id: springboot-demo-test
  # Human readable display name for this service in Uptime UI and elsewhere
  name: springboot-demo-test
  # List of URLs to query
  urls: ["http://localhost:8080/test/hello"]
  # Configure task schedule
  schedule: '@every 10s'
  check.response.status: [200]
  ipv4: true
  ipv6: true
  mode: any
  # Total test connection and data exchange timeout
  #timeout: 16s
  # Name of corresponding APM service, if Elastic APM is in use for the monitored service.
  #service.name: my-apm-service-name

# Experimental: Set this to true to run heartbeat monitors exactly once at startup
#heartbeat.run_once: true

# ======================= Elasticsearch template setting =======================

setup.template.settings:
  index.number_of_shards: 1
  index.codec: best_compression
setup.template.name: "heartbeat"
setup.template.pattern: "heartbeat-*"
setup.ilm.enabled: false


# =================================== Kibana ===================================

# Starting with Beats version 6.0.0, the dashboards are loaded via the Kibana API.
# This requires a Kibana endpoint configuration.
setup.kibana:

  # Kibana Host
  # Scheme and port can be left out and will be set to the default (http and 5601)
  # In case you specify and additional path, the scheme is required: http://localhost:5601/path
  # IPv6 addresses should always be defined as: https://[2001:db8::1]:5601
  #host: "localhost:5601"
  host: "192.168.122.118:5601"

# ---------------------------- Elasticsearch Output ----------------------------
output.elasticsearch:
  # Array of hosts to connect to.
  hosts: ["https://192.168.122.118:9200","https://192.168.122.119:9200","https://192.168.122.120:9200"]
  protocol: "https"
  username: "elastic"
  password: "elastic"
  ssl.certificate_authorities: ["/opt/module/metricbeat-8.11.0/certs/elasticsearch-ca.pem"]
  ssl.certificate: "/opt/module/metricbeat-8.11.0/certs/instance.crt"
  ssl.key: "/opt/module/metricbeat-8.11.0/certs/instance.key"

  # Protocol - either `http` (default) or `https`.
  #protocol: "https"

  # Authentication credentials - either API key or username/password.
  #api_key: "id:api_key"
  #username: "elastic"
  #password: "changeme"

# ================================= Processors =================================

processors:
  - add_observer_metadata:

2.4 设置模板

# 设置模板
./heartbeat setup

2.5 启动服务

# 编写启动命令文件
echo "nohup ./heartbeat -e  > ./heartbeat.log 2>&1 &" > start.sh
# 启动服务
./start.sh
# 查看日志
tail -200f /opt/module/heartbeat-8.11.0/heartbeat.log

2.6 检查es是否收到数据

 登入kibana ，进入observability，添加 uptime，检查 heartbeat 状态。正常后即可在observability >uptime看到监控的实例