华清远见嵌入式学习——ARM——作业4

作业要求：

代码运行效果图：

代码：

do_irq.c:

#include "key_it.h"
extern void printf(const char *fmt, ...);
unsigned int i = 0;

//延时函数
void delay(int ms)
{
  int i,j;
  for(i=0;iIAR & 0x3ff);
    switch (irqno)
    {
    case 99: // key1
        printf("KEY1_INT\n");

        //点亮两个灯
        led1_on();
        led3_on();
        delay(1000);

        //熄灭两个灯
        led1_off();
        led_off();
        delay(1000);

        // 清除GICD的中断排队标志
        GICD->ICPENDR[3] |= (0x1<<3);
        // 清除exti的事件触发标志
        EXTI->FPR1 |= (0x1<<9);

        break;
    case 97: // KEY2
        printf("KEY2_INT\n");

        //点亮三个灯
        led1_on();
        led2_on();
        led3_on();
        delay(1000);

        //熄灭三个灯
        led1_off();
        led2_off();
        led3_off();
        delay(1000);

        // 清除GICD的中断排队标志
        GICD->ICPENDR[3] |= (0x1<<1);
        // 清除exti的事件触发标志
        EXTI->FPR1 |= (0x1<<7);

        break;
    case 98: // key3
        printf("KEY3_INT\n");

        //延时点亮三个灯，一个灯亮的同时下个灯灭
        led1_on();
        delay(1000);

        led1_off();
        led2_on();
        delay(1000);

        led2_off();
        led3_on();
        delay(1000);

        led3_off();

        // 清除GICD的中断排队标志
        GICD->ICPENDR[3] |= (0x1<<2);
        // 清除exti的事件触发标志
        EXTI->FPR1 |= (0x1<<8);

        break;
    }
    // 清除中断号
    GICC->EOIR = irqno;
}

key_it.c

#include"key_it.h"
void key1_it_config()
{
    //使能GPIOF时钟
    RCC->MP_AHB4ENSETR |= (0x1<<5);
    //设置PF9管脚为输入
    GPIOF->MODER &= (~(0x3<<18));
    //设置PF9作为EXTI9事件的输入
    EXTI->EXTICR3 &= (~(0x1f<<8));
    EXTI->EXTICR3 |= (0x05<<8);
    //设置下降沿使能检测EXTI9事件
    EXTI->FTSR1 |= (0x1<<9);
    //设置EXTI9事件不屏蔽
    EXTI->C1IMR1 |= (0x1<<9);
    //GICD使能EXTI9（99号）中断
    GICD->ISENABLER[3] |= (0x1<<3);
    //GICD 设置99号中断的优先级
    GICD->IPRIORITYR[24] &= (~(0x1f<<27));
    //选择CPU0处理当前中断
    GICD->ITARGETSR[24] |= (0x1<<24);
    //全局使能组0中断被转发到GICC
    GICD->CTRL |= (0X1);
    //设置中断的优先级掩码
    GICC->PMR |= (0x1f<<3);
    //允许组0中断被CPU处理
    GICC->CTRL |= (0x1);
}
void key2_it_config()
{
    //使能GPIOF时钟
    RCC->MP_AHB4ENSETR |= (0x1<<5);
    //设置PF7管脚为输入
    GPIOF->MODER &= (~(0x3<<14));
    //设置PF7作为EXTI7事件的输入
    EXTI->EXTICR2 &= (~(0x1f<<24));
    EXTI->EXTICR2 |= (0x05<<24);
    //设置下降沿使能检测EXTI7事件
    EXTI->FTSR1 |= (0x1<<7);
    //设置EXTI7事件不屏蔽
    EXTI->C1IMR1 |= (0x1<<7);
    //GICD使能EXTI7（97号）中断
    GICD->ISENABLER[3] |= (0x1<<1);
    //GICD 设置97号中断的优先级
    GICD->IPRIORITYR[24] &= (~(0x1f<<11));
    //选择CPU0处理当前中断
    GICD->ITARGETSR[24] |= (0x1<<8);
    //全局使能组0中断被转发到GICC
    GICD->CTRL |= (0X1);
    //设置中断的优先级掩码
    GICC->PMR |= (0x1f<<3);
    //允许组0中断被CPU处理
    GICC->CTRL |= (0x1);
}
void key3_it_config()
{
    //使能GPIOF时钟
    RCC->MP_AHB4ENSETR |= (0x1<<5);
    //设置PF8管脚为输入
    GPIOF->MODER &= (~(0x3<<16));
    //设置PF8作为EXTI8事件的输入
    EXTI->EXTICR3 &= (~(0x1f));
    EXTI->EXTICR3 |= (0x05);
    //设置下降沿使能检测EXTI8事件
    EXTI->FTSR1 |= (0x1<<8);
    //设置EXTI8事件不屏蔽
    EXTI->C1IMR1 |= (0x1<<8);
    //GICD使能EXTI8（98号）中断
    GICD->ISENABLER[3] |= (0x1<<2);
    //GICD 设置98号中断的优先级
    GICD->IPRIORITYR[24] &= (~(0x1f<<19));
    //选择CPU0处理当前中断
    GICD->ITARGETSR[24] |= (0x1<<16);
    //全局使能组0中断被转发到GICC
    GICD->CTRL |= (0X1);
    //设置中断的优先级掩码
    GICC->PMR |= (0x1f<<3);
    //允许组0中断被CPU处理
    GICC->CTRL |= (0x1); 
}

led.c

#include "led.h"
void all_led_init()
{
    RCC_GPIO |= (0X3<<4);//时钟使能
    GPIOE_MODER &=(~(0X3<<20));//设置PE10输出
    GPIOE_MODER |= (0X1<<20);
    //设置PE10为推挽输出
    GPIOE_OTYPER &=(~(0x1<<10));
    //PE10为低速输出
    GPIOE_OSPEEDR &= (~(0x3<<20));
    //设置无上拉下拉
    GPIOE_PUPDR &= (~(0x3<<20));
 
    //LED2
    GPIOF_MODER &=(~(0X3<<20));//设置Pf10输出
    GPIOF_MODER |= (0X1<<20);
    //设置Pf10为推挽输出
    GPIOF_OTYPER &=(~(0x1<<10));
    //Pf10为低速输出
    GPIOF_OSPEEDR &= (~(0x3<<20));
    //设置无上拉下拉
    GPIOF_PUPDR &= (~(0x3<<20));
 
    //LED3
    GPIOE_MODER &=(~(0X3<<16));//设置PE8输出
    GPIOE_MODER |= (0X1<<16);
    //设置PE8为推挽输出
    GPIOE_OTYPER &=(~(0x1<<8));
    //PE8为低速输出
    GPIOE_OSPEEDR &= (~(0x3<16));
    //设置无上拉下拉
    GPIOE_PUPDR &= (~(0x3<<16));
}
void led1_on()
{
    GPIOE_ODR |= (0x1<<10);
}
 
void led1_off()
{
    GPIOE_ODR &= (~(0x1<<10));
}
void led2_on()
{
    GPIOF_ODR |= (0x1<<10);
}
 
void led2_off()
{
    GPIOF_ODR &= (~(0x1<<10));
}
void led3_on()
{
    GPIOE_ODR |= (0x1<<8);
}
 
void led3_off()
{
    GPIOE_ODR &= (~(0x1<<8));
}

main.c

#include "key_it.h"

int main()
{
  key1_it_config();
	key2_it_config();
	key3_it_config();
    while (1)
    {
        printf("do main...\n");
        delay(1000);
    }
}

key_it.h

#ifndef __KEY_IT_H__
#define __KEY_IT_H__
#include"stm32mp1xx_gpio.h"
#include"stm32mp1xx_gic.h"
#include"stm32mp1xx_exti.h"
#include"stm32mp1xx_rcc.h"
#include "led.h"
void key1_it_config();
void key2_it_config();
void key3_it_config();
void delay(int ms);
#endif

led.h

#ifndef __LED_H__
#define __LED_H__
 
#define RCC_GPIO (*(unsigned int *)0x50000a28)
#define GPIOE_MODER (*(unsigned int *)0x50006000)
#define GPIOF_MODER (*(unsigned int *)0x50007000)
#define GPIOE_OTYPER (*(unsigned int *)0x50006004)
#define GPIOF_OTYPER (*(unsigned int *)0x50007004)
#define GPIOE_OSPEEDR (*(unsigned int *)0x50006008)
#define GPIOF_OSPEEDR (*(unsigned int *)0x50007008)
#define GPIOE_PUPDR (*(unsigned int *)0x5000600C)
#define GPIOF_PUPDR (*(unsigned int *)0x5000700c)
#define GPIOE_ODR (*(unsigned int *)0x50006014)
#define GPIOF_ODR (*(unsigned int *)0x50007014)
 
void all_led_init();
void led1_on();
void led1_off();
void led2_on();
void led2_off();
void led3_on();
void led3_off();
 
#endif

模拟面试：