51单片机——OLED
51单片机——OLED
1.IIC协议概述
IIC全称Inter-Integrated Circuit (集成电路总线)
是由PHILIPS公司在80年代开发的两线式串行总线，用于连接微控制器及其外围设备。IIC属于半双工同步通信方式
特点
简单性和有效性。
由于接口直接在组件之上，因此IIC总线占用的空间非常小，减少了电路板的空间和芯片管脚的数量，降低了互联成本。总线的长度可高达25英尺，并且能够以10Kbps的最大传输速率支持40个组件
多主控(multimastering)
其中任何能够进行发送和接收的设备都可以成为主总线。一个主控能够控制信号的传输和时钟频率。当然，在任何时间点上只能有一个主控。
构成
IIC串行总线一般有两根信号线，一根是双向的数据线SDA，另一根是时钟线SCL，其时钟信号是由主控器件产生。所有接到IIC总线设备上的串行数据SDA都接到总线的SDA上，各设备的时钟线SCL接到总线的SCL上。对于并联在一条总线上的每个IC都有唯一的地址。
IIC协议
IIC总线在传输数据的过程中一共有三种类型信号，分别为：开始信号、结束信号和应答信号。
//起始位，停止位，数据位，速度
这些信号中，起始信号是必需的，结束信号和应答信号
应答信号
发送器每发送一个字节（8个bit），就在时钟脉冲9期间释放数据线，由接收器反馈一个应答信号。
应答信号为低电平时，规定为有效应答位（ACK，简称应答位），表示接收器已经成功地接收了该字
节；
应答信号为高电平时，规定为非应答位（NACK），一般表示接收器接收该字节没有成功。
2.IIC协议基本函数封装
#include "reg52.h"
#include "intrins.h"
sbit scl = P0^1;
sbit sda = P0^3;
void IIC_Start()
{
sda = 1;
scl = 1;
_nop_();
sda = 0;
_nop_();
}
void IIC_Stop()
{
sda = 0;
scl = 1;
_nop_();
sda = 1;
_nop_();
}
char IIC_ACK()
{
char flag;
sda = 1;//就在时钟脉冲9期间释放数据线
_nop_();
scl = 1;
_nop_();
flag = sda;
_nop_();
scl = 0;
_nop_();
return flag;
}
void IIC_Send_Byte(char dataSend)
{
int i;
for(i = 0;i<8;i++){
scl = 0;//scl拉低，让sda做好数据准备
sda = dataSend & 0x80;//1000 0000获得dataSend的最高位，给sda
_nop_();//发送数据建立时间
scl = 1;//scl拉高开始发送
_nop_();//数据发送时间
scl = 0;//发送完毕拉低
_nop_();//
dataSend = dataSend << 1;
}
}
void main()
{
int a = 10;
IIC_Start();
}
3.OLED写数据写命令函数封装
#include "reg52.h"
#include "intrins.h"
sbit scl = P0^1;
sbit sda = P0^3;
void IIC_Start()
{
sda = 1;
scl = 1;
_nop_();
sda = 0;
_nop_();
}
void IIC_Stop()
{
sda = 0;
scl = 1;
_nop_();
sda = 1;
_nop_();
}
char IIC_ACK()
{
char flag;
sda = 1;//就在时钟脉冲9期间释放数据线
_nop_();
scl = 1;
_nop_();
flag = sda;
_nop_();
scl = 0;
_nop_();
return flag;
}
void IIC_Send_Byte(char dataSend)
{
int i;
for(i = 0;i<8;i++){
scl = 0;//scl拉低，让sda做好数据准备
sda = dataSend & 0x80;//1000 0000获得dataSend的最高位，给sda
_nop_();//发送数据建立时间
scl = 1;//scl拉高开始发送
_nop_();//数据发送时间
scl = 0;//发送完毕拉低
_nop_();//
dataSend = dataSend << 1;
}
}
void Oled_Write_Cmd(char dataCmd)
{
// 1. start()
IIC_Start();
//
// 2. 写入从机地址 b0111 1000 0x78
IIC_Send_Byte(0x78);
// 3. ACK
IIC_ACK();
// 4. cotrol byte: (0)(0)000000 写入命令 (0)(1)000000写入数据
IIC_Send_Byte(0x00);
// 5. ACK
IIC_ACK();
//6. 写入指令/数据
IIC_Send_Byte(dataCmd);
//7. ACK
IIC_ACK();
//8. STOP
IIC_Stop();
}
void Oled_Write_Data(char dataData)
{
// 1. start()
IIC_Start();
//
// 2. 写入从机地址 b0111 1000 0x78
IIC_Send_Byte(0x78);
// 3. ACK
IIC_ACK();
// 4. cotrol byte: (0)(0)000000 写入命令 (0)(1)000000写入数据
IIC_Send_Byte(0x00);
// 5. ACK
IIC_ACK();
///6. 写入指令/数据
IIC_Send_Byte(dataData);
//7. ACK
IIC_ACK();
//8. STOP
IIC_Stop();
}
void main()
{
int a = 10;
IIC_Start();
}
4.OLED显示一个点
#include "reg52.h"
#include "intrins.h"
sbit scl = P0^1;
sbit sda = P0^3;
void IIC_Start()
{
sda = 1;
scl = 1;
_nop_();
sda = 0;
_nop_();
}
void IIC_Stop()
{
sda = 0;
scl = 1;
_nop_();
sda = 1;
_nop_();
}
char IIC_ACK()
{
char flag;
sda = 1;//就在时钟脉冲9期间释放数据线
_nop_();
scl = 1;
_nop_();
flag = sda;
_nop_();
scl = 0;
_nop_();
return flag;
}
void IIC_Send_Byte(char dataSend)
{
int i;
for(i = 0;i<8;i++){
scl = 0;//scl拉低，让sda做好数据准备
sda = dataSend & 0x80;//1000 0000获得dataSend的最高位，给sda
_nop_();//发送数据建立时间
scl = 1;//scl拉高开始发送
_nop_();//数据发送时间
scl = 0;//发送完毕拉低
_nop_();//
dataSend = dataSend << 1;
}
}
void Oled_Write_Cmd(char dataCmd)
{
// 1. start()
IIC_Start();
//
// 2. 写入从机地址 b0111 1000 0x78
IIC_Send_Byte(0x78);
// 3. ACK
IIC_ACK();
// 4. cotrol byte: (0)(0)000000 写入命令 (0)(1)000000写入数据
IIC_Send_Byte(0x00);
// 5. ACK
IIC_ACK();
//6. 写入指令/数据
IIC_Send_Byte(dataCmd);
//7. ACK
IIC_ACK();
//8. STOP
IIC_Stop();
}
void Oled_Write_Data(char dataData)
{
// 1. start()
IIC_Start();
//
// 2. 写入从机地址 b0111 1000 0x78
IIC_Send_Byte(0x78);
// 3. ACK
IIC_ACK();
// 4. cotrol byte: (0)(0)000000 写入命令 (0)(1)000000写入数据
IIC_Send_Byte(0x40);
// 5. ACK
IIC_ACK();
///6. 写入指令/数据
IIC_Send_Byte(dataData);
//7. ACK
IIC_ACK();
//8. STOP
IIC_Stop();
}
void Oled_Init(void){
Oled_Write_Cmd(0xAE);//--display off
Oled_Write_Cmd(0x00);//---set low column address
Oled_Write_Cmd(0x10);//---set high column address
Oled_Write_Cmd(0x40);//--set start line address
Oled_Write_Cmd(0xB0);//--set page address
Oled_Write_Cmd(0x81); // contract control
Oled_Write_Cmd(0xFF);//--128
Oled_Write_Cmd(0xA1);//set segment remap
Oled_Write_Cmd(0xA6);//--normal / reverse
Oled_Write_Cmd(0xA8);//--set multiplex ratio(1 to 64)
Oled_Write_Cmd(0x3F);//--1/32 duty
Oled_Write_Cmd(0xC8);//Com scan direction
Oled_Write_Cmd(0xD3);//-set display offset
Oled_Write_Cmd(0x00);//
Oled_Write_Cmd(0xD5);//set osc division
Oled_Write_Cmd(0x80);//
Oled_Write_Cmd(0xD8);//set area color mode off
Oled_Write_Cmd(0x05);//
Oled_Write_Cmd(0xD9);//Set Pre-Charge Period
Oled_Write_Cmd(0xF1);//
Oled_Write_Cmd(0xDA);//set com pin configuartion
Oled_Write_Cmd(0x12);//
Oled_Write_Cmd(0xDB);//set Vcomh
Oled_Write_Cmd(0x30);//
Oled_Write_Cmd(0x8D);//set charge pump enable
Oled_Write_Cmd(0x14);//
Oled_Write_Cmd(0xAF);//--turn on oled panel
}
void main()
{
int a = 10;
//1. OLED初始化
Oled_Init();
//2. 选择一个位置
//2.1 确认页寻址模式
Oled_Write_Cmd(0x20);
Oled_Write_Cmd(0x02);
//2.2 选择PAGE0 1011 0000
// 0xB0
Oled_Write_Cmd(0xB0);
//3. 显示一个点
Oled_Write_Data(0x08);
Oled_Write_Data(0x08);
Oled_Write_Data(0x08);
Oled_Write_Data(0x08);
Oled_Write_Data(0x08);
Oled_Write_Data(0x08);
Oled_Write_Data(0x08);
Oled_Write_Data(0x08);
Oled_Write_Data(0x08);
while(1);
}
5.OLED选择列地址显示
#include "reg52.h"
#include "intrins.h"
sbit scl = P0^1;
sbit sda = P0^3;
void IIC_Start()
{
scl = 0;
sda = 1;
scl = 1;
_nop_();
sda = 0;
_nop_();
}
void IIC_Stop()
{
scl = 0;
sda = 0;
scl = 1;
_nop_();
sda = 1;
_nop_();
}
char IIC_ACK()
{
char flag;
sda = 1;//就在时钟脉冲9期间释放数据线
_nop_();
scl = 1;
_nop_();
flag = sda;
_nop_();
scl = 0;
_nop_();
return flag;
}
void IIC_Send_Byte(char dataSend)
{
int i;
for(i = 0;i<8;i++){
scl = 0;//scl拉低，让sda做好数据准备
sda = dataSend & 0x80;//1000 0000获得dataSend的最高位，给sda
_nop_();//发送数据建立时间
scl = 1;//scl拉高开始发送
_nop_();//数据发送时间
scl = 0;//发送完毕拉低
_nop_();//
dataSend = dataSend << 1;
}
}
void Oled_Write_Cmd(char dataCmd)
{
// 1. start()
IIC_Start();
//
// 2. 写入从机地址 b0111 1000 0x78
IIC_Send_Byte(0x78);
// 3. ACK
IIC_ACK();
// 4. cotrol byte: (0)(0)000000 写入命令 (0)(1)000000写入数据
IIC_Send_Byte(0x00);
// 5. ACK
IIC_ACK();
//6. 写入指令/数据
IIC_Send_Byte(dataCmd);
//7. ACK
IIC_ACK();
//8. STOP
IIC_Stop();
}
void Oled_Write_Data(char dataData)
{
// 1. start()
IIC_Start();
//
// 2. 写入从机地址 b0111 1000 0x78
IIC_Send_Byte(0x78);
// 3. ACK
IIC_ACK();
// 4. cotrol byte: (0)(0)000000 写入命令 (0)(1)000000写入数据
IIC_Send_Byte(0x40);
// 5. ACK
IIC_ACK();
///6. 写入指令/数据
IIC_Send_Byte(dataData);
//7. ACK
IIC_ACK();
//8. STOP
IIC_Stop();
}
void Oled_Init(void){
Oled_Write_Cmd(0xAE);//--display off
Oled_Write_Cmd(0x00);//---set low column address
Oled_Write_Cmd(0x10);//---set high column address
Oled_Write_Cmd(0x40);//--set start line address
Oled_Write_Cmd(0xB0);//--set page address
Oled_Write_Cmd(0x81); // contract control
Oled_Write_Cmd(0xFF);//--128
Oled_Write_Cmd(0xA1);//set segment remap
Oled_Write_Cmd(0xA6);//--normal / reverse
Oled_Write_Cmd(0xA8);//--set multiplex ratio(1 to 64)
Oled_Write_Cmd(0x3F);//--1/32 duty
Oled_Write_Cmd(0xC8);//Com scan direction
Oled_Write_Cmd(0xD3);//-set display offset
Oled_Write_Cmd(0x00);//
Oled_Write_Cmd(0xD5);//set osc division
Oled_Write_Cmd(0x80);//
Oled_Write_Cmd(0xD8);//set area color mode off
Oled_Write_Cmd(0x05);//
Oled_Write_Cmd(0xD9);//Set Pre-Charge Period
Oled_Write_Cmd(0xF1);//
Oled_Write_Cmd(0xDA);//set com pin configuartion
Oled_Write_Cmd(0x12);//
Oled_Write_Cmd(0xDB);//set Vcomh
Oled_Write_Cmd(0x30);//
Oled_Write_Cmd(0x8D);//set charge pump enable
Oled_Write_Cmd(0x14);//
Oled_Write_Cmd(0xAF);//--turn on oled panel
}
void Oled_Screen_Clear(void){
char i,n;
Oled_Write_Cmd (0x20); //set memory addressing mode
Oled_Write_Cmd (0x02); //page addressing mode
for(i=0;i<8;i++){
Oled_Write_Cmd(0xb0+i); //ÉèÖÃÒ³µØÖ·£¨0~7£©
Oled_Write_Cmd(0x00); //ÉèÖÃÏÔʾλÖáªÁе͵ØÖ·
Oled_Write_Cmd(0x10); //ÉèÖÃÏÔʾλÖáªÁиߵØÖ·
for(n=0;n<128;n++)Oled_Write_Data(0x00);
}
}
void main()
{
int a = 10;
//1. OLED初始化
Oled_Init();
//2. 选择一个位置
//2.1 确认页寻址模式
Oled_Write_Cmd(0x20);
Oled_Write_Cmd(0x02);
//2.2 选择PAGE0 1011 0000
// 0xB0
Oled_Write_Cmd(0xB0);
Oled_Write_Cmd(0x00);
Oled_Write_Cmd(0x10);
//3. 显示一个点
Oled_Write_Data(0x08);
Oled_Write_Data(0x08);
Oled_Write_Data(0x08);
Oled_Write_Data(0x08);
Oled_Write_Data(0x08);
Oled_Write_Data(0x08);
Oled_Write_Data(0x08);
Oled_Write_Data(0x08);
Oled_Write_Data(0x08);
Oled_Write_Cmd(0xB5);
Oled_Write_Cmd(0x00);
Oled_Write_Cmd(0x10);
Oled_Write_Data(0x08);
Oled_Write_Data(0x08);
Oled_Write_Data(0x08);
Oled_Write_Data(0x08);
Oled_Write_Data(0x08);
Oled_Write_Data(0x08);
Oled_Write_Data(0x08);
Oled_Write_Data(0x08);
Oled_Write_Data(0x08);
Oled_Write_Cmd(0xB6);
Oled_Write_Cmd(0x00);
Oled_Write_Cmd(0x10);
Oled_Write_Data(0x08);
Oled_Write_Data(0x08);
Oled_Write_Data(0x08);
Oled_Write_Data(0x08);
Oled_Write_Data(0x08);
Oled_Write_Data(0x08);
Oled_Write_Data(0x08);
Oled_Write_Data(0x08);
Oled_Write_Data(0x08);
Oled_Write_Cmd(0x0f);
Oled_Write_Cmd(0x17);
Oled_Write_Data(0x08);
while(1);
}
6.OLED添加清屏函数
#include "reg52.h"
#include "intrins.h"
sbit scl = P0^1;
sbit sda = P0^3;
void IIC_Start()
{
scl = 0;
sda = 1;
scl = 1;
_nop_();
sda = 0;
_nop_();
}
void IIC_Stop()
{
scl = 0;
sda = 0;
scl = 1;
_nop_();
sda = 1;
_nop_();
}
char IIC_ACK()
{
char flag;
sda = 1;//就在时钟脉冲9期间释放数据线
_nop_();
scl = 1;
_nop_();
flag = sda;
_nop_();
scl = 0;
_nop_();
return flag;
}
void IIC_Send_Byte(char dataSend)
{
int i;
for(i = 0;i<8;i++){
scl = 0;//scl拉低，让sda做好数据准备
sda = dataSend & 0x80;//1000 0000获得dataSend的最高位，给sda
_nop_();//发送数据建立时间
scl = 1;//scl拉高开始发送
_nop_();//数据发送时间
scl = 0;//发送完毕拉低
_nop_();//
dataSend = dataSend << 1;
}
}
void Oled_Write_Cmd(char dataCmd)
{
// 1. start()
IIC_Start();
//
// 2. 写入从机地址 b0111 1000 0x78
IIC_Send_Byte(0x78);
// 3. ACK
IIC_ACK();
// 4. cotrol byte: (0)(0)000000 写入命令 (0)(1)000000写入数据
IIC_Send_Byte(0x00);
// 5. ACK
IIC_ACK();
//6. 写入指令/数据
IIC_Send_Byte(dataCmd);
//7. ACK
IIC_ACK();
//8. STOP
IIC_Stop();
}
void Oled_Write_Data(char dataData)
{
// 1. start()
IIC_Start();
//
// 2. 写入从机地址 b0111 1000 0x78
IIC_Send_Byte(0x78);
// 3. ACK
IIC_ACK();
// 4. cotrol byte: (0)(0)000000 写入命令 (0)(1)000000写入数据
IIC_Send_Byte(0x40);
// 5. ACK
IIC_ACK();
///6. 写入指令/数据
IIC_Send_Byte(dataData);
//7. ACK
IIC_ACK();
//8. STOP
IIC_Stop();
}
void Oled_Init(void){
Oled_Write_Cmd(0xAE);//--display off
Oled_Write_Cmd(0x00);//---set low column address
Oled_Write_Cmd(0x10);//---set high column address
Oled_Write_Cmd(0x40);//--set start line address
Oled_Write_Cmd(0xB0);//--set page address
Oled_Write_Cmd(0x81); // contract control
Oled_Write_Cmd(0xFF);//--128
Oled_Write_Cmd(0xA1);//set segment remap
Oled_Write_Cmd(0xA6);//--normal / reverse
Oled_Write_Cmd(0xA8);//--set multiplex ratio(1 to 64)
Oled_Write_Cmd(0x3F);//--1/32 duty
Oled_Write_Cmd(0xC8);//Com scan direction
Oled_Write_Cmd(0xD3);//-set display offset
Oled_Write_Cmd(0x00);//
Oled_Write_Cmd(0xD5);//set osc division
Oled_Write_Cmd(0x80);//
Oled_Write_Cmd(0xD8);//set area color mode off
Oled_Write_Cmd(0x05);//
Oled_Write_Cmd(0xD9);//Set Pre-Charge Period
Oled_Write_Cmd(0xF1);//
Oled_Write_Cmd(0xDA);//set com pin configuartion
Oled_Write_Cmd(0x12);//
Oled_Write_Cmd(0xDB);//set Vcomh
Oled_Write_Cmd(0x30);//
Oled_Write_Cmd(0x8D);//set charge pump enable
Oled_Write_Cmd(0x14);//
Oled_Write_Cmd(0xAF);//--turn on oled panel
}
void Oled_Clear()
{
unsigned char i,j; //-128 --- 127
for(i=0;i<8;i++){
Oled_Write_Cmd(0xB0 + i);//page0--page7
//每个page从0列
Oled_Write_Cmd(0x00);
Oled_Write_Cmd(0x10);
//0到127列，依次写入0，每写入数据，列地址自动偏移
for(j = 0;j<128;j++){
Oled_Write_Data(0);
}
}
}
void main()
{
int a = 10;
//1. OLED初始化
Oled_Init();
//2. 选择一个位置
//2.1 确认页寻址模式
Oled_Write_Cmd(0x20);
Oled_Write_Cmd(0x02);
Oled_Clear();
//2.2 选择PAGE0 1011 0000
// 0xB0
Oled_Write_Cmd(0xB0);
Oled_Write_Cmd(0x00);
Oled_Write_Cmd(0x10);
//3. 显示一个点
Oled_Write_Data(0x08);
Oled_Write_Data(0x08);
Oled_Write_Data(0x08);
Oled_Write_Data(0x08);
Oled_Write_Data(0x08);
Oled_Write_Data(0x08);
Oled_Write_Data(0x08);
Oled_Write_Data(0x08);
Oled_Write_Data(0x08);
Oled_Write_Cmd(0xB5);
Oled_Write_Cmd(0x00);
Oled_Write_Cmd(0x10);
Oled_Write_Data(0x08);
Oled_Write_Data(0x08);
Oled_Write_Data(0x08);
Oled_Write_Data(0x08);
Oled_Write_Data(0x08);
Oled_Write_Data(0x08);
Oled_Write_Data(0x08);
Oled_Write_Data(0x08);
Oled_Write_Data(0x08);
Oled_Write_Cmd(0xB6);
Oled_Write_Cmd(0x00);
Oled_Write_Cmd(0x10);
Oled_Write_Data(0x08);
Oled_Write_Data(0x08);
Oled_Write_Data(0x08);
Oled_Write_Data(0x08);
Oled_Write_Data(0x08);
Oled_Write_Data(0x08);
Oled_Write_Data(0x08);
Oled_Write_Data(0x08);
Oled_Write_Data(0x08);
Oled_Write_Cmd(0x0f);
Oled_Write_Cmd(0x17);
Oled_Write_Data(0x08);
while(1);
}
7.OLED显示字符A
#include "reg52.h"
#include "intrins.h"
sbit scl = P0^1;
sbit sda = P0^3;
void IIC_Start()
{
scl = 0;
sda = 1;
scl = 1;
_nop_();
sda = 0;
_nop_();
}
void IIC_Stop()
{
scl = 0;
sda = 0;
scl = 1;
_nop_();
sda = 1;
_nop_();
}
char IIC_ACK()
{
char flag;
sda = 1;//就在时钟脉冲9期间释放数据线
_nop_();
scl = 1;
_nop_();
flag = sda;
_nop_();
scl = 0;
_nop_();
return flag;
}
void IIC_Send_Byte(char dataSend)
{
int i;
for(i = 0;i<8;i++){
scl = 0;//scl拉低，让sda做好数据准备
sda = dataSend & 0x80;//1000 0000获得dataSend的最高位，给sda
_nop_();//发送数据建立时间
scl = 1;//scl拉高开始发送
_nop_();//数据发送时间
scl = 0;//发送完毕拉低
_nop_();//
dataSend = dataSend << 1;
}
}
void Oled_Write_Cmd(char dataCmd)
{
// 1. start()
IIC_Start();
//
// 2. 写入从机地址 b0111 1000 0x78
IIC_Send_Byte(0x78);
// 3. ACK
IIC_ACK();
// 4. cotrol byte: (0)(0)000000 写入命令 (0)(1)000000写入数据
IIC_Send_Byte(0x00);
// 5. ACK
IIC_ACK();
//6. 写入指令/数据
IIC_Send_Byte(dataCmd);
//7. ACK
IIC_ACK();
//8. STOP
IIC_Stop();
}
void Oled_Write_Data(char dataData)
{
// 1. start()
IIC_Start();
//
// 2. 写入从机地址 b0111 1000 0x78
IIC_Send_Byte(0x78);
// 3. ACK
IIC_ACK();
// 4. cotrol byte: (0)(0)000000 写入命令 (0)(1)000000写入数据
IIC_Send_Byte(0x40);
// 5. ACK
IIC_ACK();
///6. 写入指令/数据
IIC_Send_Byte(dataData);
//7. ACK
IIC_ACK();
//8. STOP
IIC_Stop();
}
void Oled_Init(void){
Oled_Write_Cmd(0xAE);//--display off
Oled_Write_Cmd(0x00);//---set low column address
Oled_Write_Cmd(0x10);//---set high column address
Oled_Write_Cmd(0x40);//--set start line address
Oled_Write_Cmd(0xB0);//--set page address
Oled_Write_Cmd(0x81); // contract control
Oled_Write_Cmd(0xFF);//--128
Oled_Write_Cmd(0xA1);//set segment remap
Oled_Write_Cmd(0xA6);//--normal / reverse
Oled_Write_Cmd(0xA8);//--set multiplex ratio(1 to 64)
Oled_Write_Cmd(0x3F);//--1/32 duty
Oled_Write_Cmd(0xC8);//Com scan direction
Oled_Write_Cmd(0xD3);//-set display offset
Oled_Write_Cmd(0x00);//
Oled_Write_Cmd(0xD5);//set osc division
Oled_Write_Cmd(0x80);//
Oled_Write_Cmd(0xD8);//set area color mode off
Oled_Write_Cmd(0x05);//
Oled_Write_Cmd(0xD9);//Set Pre-Charge Period
Oled_Write_Cmd(0xF1);//
Oled_Write_Cmd(0xDA);//set com pin configuartion
Oled_Write_Cmd(0x12);//
Oled_Write_Cmd(0xDB);//set Vcomh
Oled_Write_Cmd(0x30);//
Oled_Write_Cmd(0x8D);//set charge pump enable
Oled_Write_Cmd(0x14);//
Oled_Write_Cmd(0xAF);//--turn on oled panel
}
void Oled_Clear()
{
unsigned char i,j; //-128 --- 127
for(i=0;i<8;i++){
Oled_Write_Cmd(0xB0 + i);//page0--page7
//每个page从0列
Oled_Write_Cmd(0x00);
Oled_Write_Cmd(0x10);
//0到127列，依次写入0，每写入数据，列地址自动偏移
for(j = 0;j<128;j++){
Oled_Write_Data(0);
}
}
}
/*-- 文字: A --*/
/*-- 宋体12; 此字体下对应的点阵为：宽x高=8x16 --*/
char A1[8] = {0x00,0x00,0xC0,0x38,0xE0,0x00,0x00,0x00};
char A2[8] = {0x20,0x3C,0x23,0x02,0x02,0x27,0x38,0x20};
void main()
{
int i;
//1. OLED初始化
Oled_Init();
//2. 选择一个位置
//2.1 确认页寻址模式
Oled_Write_Cmd(0x20);
Oled_Write_Cmd(0x02);
Oled_Clear();
//2.2 选择PAGE0 1011 0000
// 0xB0
Oled_Write_Cmd(0xB0);
Oled_Write_Cmd(0x00);
Oled_Write_Cmd(0x10);
for(i=0;i<8;i++){
Oled_Write_Data(A1[i]);
}
Oled_Write_Cmd(0xB1);
Oled_Write_Cmd(0x00);
Oled_Write_Cmd(0x10);
for(i=0;i<8;i++){
Oled_Write_Data(A2[i]);
}
while(1);
}
8.OLED显示文字
#include "reg52.h"
#include "intrins.h"
sbit sda=P0^3;
sbit scl=P0^1;
void IIC_Start()
{
scl=0;
sda = 1;
scl = 1;
_nop_();
sda = 0;
_nop_();
}
void IIC_Stop()
{
scl=0;
sda=0;
scl=1;
_nop_();
sda=1;
_nop_();
}
char IIC_Ack()
{
char flag;
sda=1;
_nop_();
scl=1;
_nop_();
flag=sda;
_nop_();
scl=0;
_nop_();
return flag;
}
void IIC_Send_Byte(char dataSend)
{
int i;
for(i=0;i<8;i++)
{
scl=0; //scl拉低,让sda做好数据准备
sda=dataSend&0x80; //获得dataSend的最高位
_nop_(); //延时一段时间
scl=1; //开始发送
_nop_();
scl=0; //发送完毕
_nop_();
dataSend=dataSend<<1;
}
}
void Oled_write_Cmd(char cmd)
{
//1. start()
IIC_Start();
// 2. 写入 b0111 1000 0x78
IIC_Send_Byte(0x78);
// 3. ACK
IIC_Ack();
//4. cotrol byte: (0)(0)000000 写入命令 (0)(1)000000写入数据
IIC_Send_Byte(0x00);
//5. ACK
IIC_Ack();
//6. 写入指令/数据
IIC_Send_Byte(cmd);
// 7. ACK
IIC_Ack();
// 8. STOP
IIC_Stop();
}
void Oled_Write_Data(char dataData)
{
//1. start()
IIC_Start();
// 2. 写入 b0111 1000 0x78
IIC_Send_Byte(0x78);
// 3. ACK
IIC_Ack();
//4. cotrol byte: (0)(0)000000 写入命令 (0)(1)000000写入数据
IIC_Send_Byte(0x40);
//5. ACK
IIC_Ack();
//6. 写入指令/数据
IIC_Send_Byte(dataData);
// 7. ACK
IIC_Ack();
// 8. STOP
IIC_Stop();
}
void Oled_Init()
{
Oled_write_Cmd(0xAE);
Oled_write_Cmd(0x00);
Oled_write_Cmd(0x10);
Oled_write_Cmd(0x40);
Oled_write_Cmd(0xB0);
Oled_write_Cmd(0x81);
Oled_write_Cmd(0xFF);
Oled_write_Cmd(0xA1);
Oled_write_Cmd(0xA6);
Oled_write_Cmd(0xA8);
Oled_write_Cmd(0x3F);
Oled_write_Cmd(0xC8);
Oled_write_Cmd(0xD3);
Oled_write_Cmd(0x00);
Oled_write_Cmd(0xD5);
Oled_write_Cmd(0x80);
Oled_write_Cmd(0xD8);
Oled_write_Cmd(0x05);
Oled_write_Cmd(0xD9);
Oled_write_Cmd(0xF1);
Oled_write_Cmd(0xDA);
Oled_write_Cmd(0x12);
Oled_write_Cmd(0xDB);
Oled_write_Cmd(0x30);
Oled_write_Cmd(0x8D);
Oled_write_Cmd(0x14);
Oled_write_Cmd(0xAF);
}
void Oled_Clear()
{
unsigned char i,j;
for(i=0;i<8;i++)
{
Oled_write_Cmd(0xB0+i);//page0到page7
//每个page从0开始
Oled_write_Cmd(0x00);
Oled_write_Cmd(0x10);
//0到127列，依次写入数据0，自动偏移
for(j=0;j<128;j++)
{
Oled_Write_Data(0);
}
}
}
/*-- 文字: 卧 --*/
/*-- 宋体12; 此字体下对应的点阵为：宽x高=16x16 --*/
code char W1[]={0x00,0xFE,0x22,0x22,0x3E,0x22,0x22,0xE2,0x02,0x00,0xFF,0x20,0x40,0x80,0x00,0x00};
code char W2[]={0x00,0x3F,0x22,0x22,0x3E,0x22,0x22,0x23,0x20,0x00,0xFF,0x00,0x00,0x00,0x03,0x00};
/*-- 文字: 槽 --*/
/*-- 宋体12; 此字体下对应的点阵为：宽x高=16x16 --*/
code char A1[]={0x10,0x10,0xD0,0xFF,0x90,0x04,0xF4,0x54,0xFF,0x54,0x54,0xFF,0x54,0xF4,0x04,0x00};
code char A2[]={0x04,0x03,0x00,0xFF,0x00,0x01,0x01,0xFD,0x55,0x55,0x55,0x55,0xFD,0x01,0x00,0x00};
/*-- 文字: , --*/
/*-- 宋体12; 此字体下对应的点阵为：宽x高=16x16 --*/
code char D1[]={0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00};
code char D2[]={0x00,0x90,0x70,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00};
/*-- 文字: 谢 --*/
/*-- 宋体12; 此字体下对应的点阵为：宽x高=16x16 --*/
code char X1[]={0x40,0x42,0xCC,0x00,0x00,0xFC,0x56,0x55,0xFC,0x80,0x10,0x10,0xFF,0x10,0x10,0x00};
code char X2[]={0x00,0x00,0x3F,0x10,0x2A,0x13,0x4A,0x86,0x7F,0x00,0x43,0x80,0x7F,0x00,0x00,0x00};
/*-- 文字: 文 --*/
/*-- 宋体12; 此字体下对应的点阵为：宽x高=16x16 --*/
code char E1[]={0x08,0x08,0x08,0x38,0xC8,0x08,0x09,0x0E,0x08,0x08,0xC8,0x38,0x08,0x08,0x08,0x00};
code char E2[]={0x80,0x80,0x40,0x40,0x20,0x11,0x0A,0x04,0x0A,0x11,0x20,0x40,0x40,0x80,0x80,0x00};
/*-- 文字: 辉 --*/
/*-- 宋体12; 此字体下对应的点阵为：宽x高=16x16 --*/
code char H1[]={0x44,0x58,0xC0,0x7F,0xD0,0x48,0x26,0x22,0xE2,0x3A,0xA2,0x22,0x22,0x2A,0x06,0x00};
code char H2[]={0x80,0x60,0x1F,0x00,0x7F,0x20,0x10,0x13,0x12,0x12,0xFF,0x12,0x12,0x12,0x10,0x00};
/*-- 文字: 真 --*/
/*-- 宋体12; 此字体下对应的点阵为：宽x高=16x16 --*/
code char Z1[]={0x00,0x04,0x04,0xF4,0x54,0x54,0x54,0x5F,0x54,0x54,0x54,0xF4,0x04,0x04,0x00,0x00};
code char Z2[]={0x10,0x10,0x90,0x5F,0x35,0x15,0x15,0x15,0x15,0x15,0x35,0x5F,0x90,0x10,0x10,0x00};
/*-- 文字: 的 --*/
/*-- 宋体12; 此字体下对应的点阵为：宽x高=16x16 --*/
code char B1[]={0x00,0xF8,0x0C,0x0B,0x08,0x08,0xF8,0x40,0x30,0x8F,0x08,0x08,0x08,0xF8,0x00,0x00};
code char B2[]={0x00,0x7F,0x21,0x21,0x21,0x21,0x7F,0x00,0x00,0x00,0x43,0x80,0x40,0x3F,0x00,0x00};
/*-- 文字: 帅 --*/
/*-- 宋体12; 此字体下对应的点阵为：宽x高=16x16 --*/
code char S1[]={0x00,0xFC,0x00,0x00,0xFF,0x00,0x00,0xF0,0x10,0x10,0xFF,0x10,0x10,0xF0,0x00,0x00};
code char S2[]={0x00,0x87,0x40,0x30,0x0F,0x00,0x00,0x1F,0x00,0x00,0xFF,0x08,0x10,0x0F,0x00,0x00};
int i;
void Oled_Show_Up()
{
for(i=0;i<16;i++)
{
Oled_Write_Data(W1[i]);
}
for(i=0;i<16;i++)
{
Oled_Write_Data(A1[i]);
}
for(i=0;i<16;i++)
{
Oled_Write_Data(D1[i]);
}
for(i=0;i<16;i++)
{
Oled_Write_Data(X1[i]);
}
for(i=0;i<16;i++)
{
Oled_Write_Data(E1[i]);
}
for(i=0;i<16;i++)
{
Oled_Write_Data(H1[i]);
}
for(i=0;i<16;i++)
{
Oled_Write_Data(Z1[i]);
}
for(i=0;i<16;i++)
{
Oled_Write_Data(B1[i]);
}
}
void Oled_Show_Down()
{
for(i=0;i<16;i++)
{
Oled_Write_Data(W2[i]);
}
for(i=0;i<16;i++)
{
Oled_Write_Data(A2[i]);
}
for(i=0;i<16;i++)
{
Oled_Write_Data(D2[i]);
}
for(i=0;i<16;i++)
{
Oled_Write_Data(X2[i]);
}
for(i=0;i<16;i++)
{
Oled_Write_Data(E2[i]);
}
for(i=0;i<16;i++)
{
Oled_Write_Data(H2[i]);
}
for(i=0;i<16;i++)
{
Oled_Write_Data(Z2[i]);
}
for(i=0;i<16;i++)
{
Oled_Write_Data(B2[i]);
}
}
void main()
{
//1.oled初始化
Oled_Init();
//2.选择一个位置
//2.1确认页寻址模式
Oled_write_Cmd(0x20);
Oled_write_Cmd(0x02);
Oled_Clear();
//2.2选择page0
Oled_write_Cmd(0xB0);
Oled_write_Cmd(0x00);
Oled_write_Cmd(0x10);
Oled_Show_Up();
Oled_write_Cmd(0xB1);
Oled_write_Cmd(0x00);
Oled_write_Cmd(0x10);
Oled_Show_Down();
Oled_write_Cmd(0xB2);
Oled_write_Cmd(0x00);
Oled_write_Cmd(0x10);
for(i=0;i<16;i++)
{
Oled_Write_Data(S1[i]);
}
Oled_write_Cmd(0xB3);
Oled_write_Cmd(0x00);
Oled_write_Cmd(0x10);
for(i=0;i<16;i++)
{
Oled_Write_Data(S2[i]);
}
while(1);
}
9.OLED显示图片
#include "reg52.h"
#include "intrins.h"
sbit sda=P0^3;
sbit scl=P0^1;
void IIC_Start()
{
scl=0;
sda = 1;
scl = 1;
_nop_();
sda = 0;
_nop_();
}
void IIC_Stop()
{
scl=0;
sda=0;
scl=1;
_nop_();
sda=1;
_nop_();
}
char IIC_Ack()
{
char flag;
sda=1;
_nop_();
scl=1;
_nop_();
flag=sda;
_nop_();
scl=0;
_nop_();
return flag;
}
void IIC_Send_Byte(char dataSend)
{
int i;
for(i=0;i<8;i++)
{
scl=0; //scl拉低,让sda做好数据准备
sda=dataSend&0x80; //获得dataSend的最高位
_nop_(); //延时一段时间
scl=1; //开始发送
_nop_();
scl=0; //发送完毕
_nop_();
dataSend=dataSend<<1;
}
}
void Oled_write_Cmd(char cmd)
{
//1. start()
IIC_Start();
// 2. 写入 b0111 1000 0x78
IIC_Send_Byte(0x78);
// 3. ACK
IIC_Ack();
//4. cotrol byte: (0)(0)000000 写入命令 (0)(1)000000写入数据
IIC_Send_Byte(0x00);
//5. ACK
IIC_Ack();
//6. 写入指令/数据
IIC_Send_Byte(cmd);
// 7. ACK
IIC_Ack();
// 8. STOP
IIC_Stop();
}
void Oled_Write_Data(char dataData)
{
//1. start()
IIC_Start();
// 2. 写入 b0111 1000 0x78
IIC_Send_Byte(0x78);
// 3. ACK
IIC_Ack();
//4. cotrol byte: (0)(0)000000 写入命令 (0)(1)000000写入数据
IIC_Send_Byte(0x40);
//5. ACK
IIC_Ack();
//6. 写入指令/数据
IIC_Send_Byte(dataData);
// 7. ACK
IIC_Ack();
// 8. STOP
IIC_Stop();
}
void Oled_Init()
{
Oled_write_Cmd(0xAE);
Oled_write_Cmd(0x00);
Oled_write_Cmd(0x10);
Oled_write_Cmd(0x40);
Oled_write_Cmd(0xB0);
Oled_write_Cmd(0x81);
Oled_write_Cmd(0xFF);
Oled_write_Cmd(0xA1);
Oled_write_Cmd(0xA6);
Oled_write_Cmd(0xA8);
Oled_write_Cmd(0x3F);
Oled_write_Cmd(0xC8);
Oled_write_Cmd(0xD3);
Oled_write_Cmd(0x00);
Oled_write_Cmd(0xD5);
Oled_write_Cmd(0x80);
Oled_write_Cmd(0xD8);
Oled_write_Cmd(0x05);
Oled_write_Cmd(0xD9);
Oled_write_Cmd(0xF1);
Oled_write_Cmd(0xDA);
Oled_write_Cmd(0x12);
Oled_write_Cmd(0xDB);
Oled_write_Cmd(0x30);
Oled_write_Cmd(0x8D);
Oled_write_Cmd(0x14);
Oled_write_Cmd(0xAF);
}
void Oled_Clear()
{
unsigned char i,j;
for(i=0;i<8;i++)
{
Oled_write_Cmd(0xB0+i);//page0到page7
//每个page从0开始
Oled_write_Cmd(0x00);
Oled_write_Cmd(0x10);
//0到127列，依次写入数据0，自动偏移
for(j=0;j<128;j++)
{
Oled_Write_Data(0);
}
}
}
code unsigned char bmpImager[]={
/*-- 调入了一幅图像：D:\无标题.bmp --*/
/*-- 宽度x高度=128x64 --128x8x8*/
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0xF0,0x08,0x0C,0x04,0x06,0x06,0x0C,0x04,0x0C,0xFC,0x1C,0x74,0xFC,0xF8,
0xF0,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x01,0x07,0x04,0x88,0xF8,0x08,0x08,0x0C,0x06,0x01,0x00,0x00,0x01,0x1F,
0x7F,0xFF,0xDC,0xF8,0xE0,0xC0,0x40,0xC0,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xE0,0x10,0x18,0x08,0x0C,
0x04,0x04,0x06,0x02,0x01,0x01,0x00,0x00,0x00,0x00,0xFF,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x3F,0x60,0xC0,0x80,0x80,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x3F,0xE0,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,
0x03,0x06,0x1C,0xF0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x07,0xFC,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x08,0x08,0x88,0xE8,0x38,0x0E,0x09,0x08,
0x08,0x88,0xE8,0x18,0x08,0x08,0x08,0x00,0x00,0xFF,0x89,0x89,0x89,0xFF,0x00,0xFF,
0x89,0x89,0x89,0x89,0xFF,0x00,0x00,0x04,0x04,0x84,0x74,0x6F,0xA4,0x24,0x24,0x24,
0x24,0xA4,0x64,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x80,0xF0,0x1F,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0x7F,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x10,0x10,0x10,0x08,0x09,0x09,0x06,0x06,
0x06,0x05,0x08,0x08,0x10,0x10,0x00,0x00,0x0C,0x03,0x10,0x10,0x10,0x1F,0x18,0x07,
0x00,0x00,0x10,0x10,0x1F,0x00,0x10,0x08,0x06,0x11,0x10,0x08,0x09,0x0A,0x06,0x06,
0x0B,0x08,0x10,0x10,0x10,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xF0,
0x1E,0x03,0x00,0x00,0xC0,0x60,0x30,0x0C,0x04,0x06,0x02,0x01,0x01,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x03,
0x1E,0x60,0x78,0x0F,0x01,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
};
void Oled_Show_Imager(unsigned char *image)
{
unsigned char i;
unsigned int j;
for(i=0;i<8;i++)
{
Oled_write_Cmd(0xB0+i);//page0到page7
//每个page从0开始
Oled_write_Cmd(0x00);
Oled_write_Cmd(0x10);
//0到127列，依次写入数据0，自动偏移
for(j=128*i;j<(128*(i+1));j++)
{
Oled_Write_Data(image[j]);
}
}
}
void main()
{
//1.oled初始化
Oled_Init();
//2.选择一个位置
//2.1确认页寻址模式
Oled_write_Cmd(0x20);
Oled_write_Cmd(0x02);
Oled_Clear();
Oled_Show_Imager(bmpImager);
while(1);
}
00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x03,
0x1E,0x60,0x78,0x0F,0x01,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
};
void Oled_Show_Imager(unsigned char *image)
{
unsigned char i;
unsigned int j;
for(i=0;i<8;i++)
{
Oled_write_Cmd(0xB0+i);//page0到page7
//每个page从0开始
Oled_write_Cmd(0x00);
Oled_write_Cmd(0x10);
//0到127列，依次写入数据0，自动偏移
for(j=128i;j<(128(i+1));j++)
{
Oled_Write_Data(image[j]);
}
}
}
void main()
{
//1.oled初始化
Oled_Init();
//2.选择一个位置
//2.1确认页寻址模式
Oled_write_Cmd(0x20);
Oled_write_Cmd(0x02);
Oled_Clear();
Oled_Show_Imager(bmpImager);
while(1);
}