本文转载自: https://blog.csdn.net/lovechris00/article/details/81631050
networksetup
networksetup
方法及使用
networkservice
hardwareports
computername
dhcp、route、domain
ipv4 & ipv6
dns
domain
代理 proxy
ftp代理
网页代理
安全网页代理
流代理
gopher 代理
设置忽略这些主机与域的代理设置
使用被动FTP模式
airport
preferredwirelessnetworks 首选网络
networkserviceenabled
MTU
media
VLAN
pppoe
8021
方法详细说明
命令手册：
$ man networksetup
可以知道 networksetup 命令地址是：/usr/sbin/networksetup
The networksetup command is used to configure network settings typically configured in
the System Preferences application. The networksetup command requires at least "admin"
privileges to run. Most of the set commands require "root" privileges to run.
Any flag that takes a password will accept "-" in place of the password to indicate it
should read the password from stdin.
networksetup 命令是用来配置 系统偏好设置中的 网络设置，networksetup 需要至少 admin 权限来运行。部分命令需要 root 权限。
方法及使用
networkservice
[-listnetworkserviceorder]
[-listallnetworkservices]
[-getinfo networkservice]
1
使用示例：
$ networksetup -getinfo "Wi-Fi"
DHCP Configuration
IP address: 10.2.5.1
Subnet mask: 255.255.0.0
Router: 10.24.0.1
Client ID:
IPv6: Automatic
IPv6 IP address: none
IPv6 Router: none
Wi-Fi ID: 88:88:98:cc:22:00
2
$ networksetup -listnetworkserviceorder
An asterisk (*) denotes that a network service is disabled.
(1) iPad USB
(Hardware Port: iPad USB, Device: en5)
(2) iPhone USB
(Hardware Port: iPhone USB, Device: en4)
(3) Wi-Fi
(Hardware Port: Wi-Fi, Device: en0)
(4) Bluetooth PAN
(Hardware Port: Bluetooth PAN, Device: en3)
(5) Thunderbolt Bridge
(Hardware Port: Thunderbolt Bridge, Device: bridge0)
3
$ networksetup -listallnetworkservices
An asterisk (*) denotes that a network service is disabled.
iPad USB
iPhone USB
Wi-Fi
Bluetooth PAN
Thunderbolt Bridge
hardwareports
[-listallhardwareports]
[-detectnewhardware]
[-getmacaddress hardwareport]
使用示例：
$ networksetup -listallhardwareports
Hardware Port: Wi-Fi
Device: en0
Ethernet Address: 88:88:98:cc:22:00
Hardware Port: Bluetooth PAN
Device: en3
Ethernet Address: 88:88:98:cc:22:01
Hardware Port: Thunderbolt 1
Device: en1
Ethernet Address: 88:88:98:cc:22:02
Hardware Port: Thunderbolt 2
Device: en2
Ethernet Address: 88:88:98:cc:22:03
Hardware Port: Thunderbolt Bridge
Device: bridge0
Ethernet Address: 88:88:98:cc:22:04
VLAN Configurations
===================
computername
[-getcomputername]
[-setcomputername computername]
dhcp、route、domain
[-setmanual networkservice ip subnet router]
[-setdhcp networkservice [clientid]]
[-setbootp networkservice]
[-setmanualwithdhcprouter networkservice ip]
[-getadditionalroutes networkservice]
[-setadditionalroutes networkservice [dest1 mask1 gate1] [dest2 mask2 gate2] ..
. [destN maskN gateN]]
使用示例：
$ networksetup -setmanual "Built-in Ethernet" 192.168.100.100 255.255.255.0 192.168.100.1
ipv4 & ipv6
[-setv4off networkservice]
[-setv6off networkservice]
[-setv6automatic networkservice]
[-setv6linklocal networkservice]
[-setv6manual networkservice address prefixLength router]
[-getv6additionalroutes networkservice]
[-setv6additionalroutes networkservice [dest1 prefixlength1 gate1] [dest2 prefi
xlength2 gate2] ... [destN prefixlengthN gateN]]
dns
[-getdnsservers networkservice]
[-setdnsservers networkservice dns1 [dns2] [...]]
使用示例：
$ networksetup -setdnsservers "Built-in Ethernet" 192.168.100.100 192.168.100.12
$ networksetup -getdnsservers "Wi-Fi"
There aren't any DNS Servers set on Wi-Fi.
$ networksetup -getdnsservers en0
en0 is not a recognized network service.
** Error: The parameters were not valid.
domain
[-getsearchdomains networkservice]
[-setsearchdomains networkservice domain1 [domain2] [...]]
[-create6to4service networkservicename]
[-set6to4automatic networkservice]
[-set6to4manual networkservice relayAddress]
networksetup -setsearchdomains "Built-in Ethernet" company.com corp.com
代理 proxy
ftp代理
[-getftpproxy networkservice]
[-setftpproxy networkservice domain portnumber authenticated username password]
[-setftpproxystate networkservice on | off]
网页代理
[-getwebproxy networkservice]
[-setwebproxy networkservice domain portnumber authenticated username password]
[-setwebproxystate networkservice on | off]
networksetup -setwebproxy "Built-in Ethernet" proxy.company.com 80
networksetup -setwebproxy "Built-In Ethernet" proxy.company.com 80 On authusername
authpassword
安全网页代理
[-getsecurewebproxy networkservice]
[-setsecurewebproxy networkservice domain portnumber authenticated username password]
[-setsecurewebproxystate networkservice on | off]
流代理
[-getstreamingproxy networkservice]
[-setstreamingproxy networkservice domain portnumber authenticated username password]
[-setstreamingproxystate networkservice on | off]
gopher 代理
[-getgopherproxy networkservice]
[-setgopherproxy networkservice domain portnumber authenticated username password]
[-setgopherproxystate networkservice on | off]
[-getsocksfirewallproxy networkservice]
[-setsocksfirewallproxy networkservice domain portnumber authenticated username password]
[-setsocksfirewallproxystate networkservice on | off]
设置忽略这些主机与域的代理设置
[-getproxybypassdomains networkservice]
[-setproxybypassdomains networkservice domain1 [domain2] [...]]
[-getproxyautodiscovery networkservice]
[-setproxyautodiscovery networkservice on | off]
使用被动FTP模式
[-getpassiveftp networkservice]
[-setpassiveftp networkservice on | off]
使用示例：
1
$ networksetup -setwebproxy "Wi-Fi" 10.240.188.10 8080
2
$ sudo networksetup -getproxybypassdomains "Wi-Fi"
$ networksetup -setproxybypassdomains "Wi-Fi" *.local、169.254/16、10.24
3
$ networksetup -getpassiveftp "Wi-Fi"
Passive FTP: Off
airport
[-getairportnetwork device]
[-setairportnetwork device network [password]]
[-getairportpower device]
[-setairportpower device on | off]
使用示例：
1
$ networksetup -getairportnetwork en0
Current Wi-Fi Network: MS480-5G
$ networksetup -getairportnetwork en1
en1 is not a Wi-Fi interface.
** Error: Error obtaining wireless information.
preferredwirelessnetworks 首选网络
[-listpreferredwirelessnetworks hardwareport]
[-addpreferredwirelessnetworkatindex hardwareport network index securitytype [password]]
[-removepreferredwirelessnetwork hardwareport network]
[-removeallpreferredwirelessnetworks hardwareport]
使用示例：
列出来的都是什么鬼？。。。
$ networksetup -listpreferredwirelessnetworks en0
Preferred networks on en0:
@PHICOMM_48
@PHICOMM_480
TP-LINK_CED0
MITEA
久赞
311
老北京饺子馆
xiaocuzi
帝曼斯
多喜爱面馆
欢迎光临
NJTY
xiaomi007
10D2
iOS测试机
麦客披萨
茶博会
探鱼Tanyu
LEGEND FITNESS
HoneyMoon_TeaRoom
haoyun
qfang
滋补皇
WUMU
networkserviceenabled
[-getnetworkserviceenabled networkservice]
[-setnetworkserviceenabled networkservice on | off]
[-createnetworkservice networkservicename hardwareport]
[-renamenetworkservice networkservice newnetworkservicename]
[-getdnsservers networkservice newnetworkservicename]
[-removenetworkservice networkservice]
[-ordernetworkservices service1 [service2] [service3] [...]]
使用示例：
$ networksetup -getnetworkserviceenabled "Wi-Fi"
Enabled
$ networksetup -getnetworkserviceenabled en0
en0 is not a recognized network service.
** Error: The parameters were not valid.
$ networksetup -duplicatenetworkservice "Built-In Ethernet" "Local LAN"
MTU
[-getMTU hardwareport]
[-setMTU hardwarePort value]
[-listvalidMTUrange hardwareport]
使用示例：
$ networksetup -getMTU en0
Active MTU: 1500 (Current Setting: 1500)
$ networksetup -getMTU "Wi-Fi"
Active MTU: 1500 (Current Setting: 1500)
$ networksetup -setMTU en0 1500
media
[-getmedia hardwareport]
[-setmedia hardwareport subtype [option1] [option2] [...]]
[-listvalidmedia hardwareport]
使用示例：
$ networksetup -getmedia en0
Current: autoselect
Active: autoselect
$ networksetup -setMedia en0 autoselect
$ networksetup -setMedia en0 100baseTX half-duplex
$ networksetup -listvalidmedia en0
autoselect
VLAN
[-createVLAN name parentdevice tag]
[-deleteVLAN name parentdevice tag] [-listVLANs]
[-listdevicesthatsupportVLAN]
[-isBondSupported device]
[-createBond name [device1] [device2] [...]] [-deleteBond bond]
[-addDeviceToBond device bond]
[-removeDeviceFromBond device bond] [-listBonds]
[-showBondStatus bond]
使用示例：
$ networksetup -createBond MyBond en0 en1
$ networksetup -addDeviceToBond en0 bond0
3
pppoe
[-listpppoeservices]
[-showpppoestatus name]
[-createpppoeservice device name account password [pppoeName]]
[-deletepppoeservice service]
使用示例：
$ networksetup -setpppoepassword MyPPPoE - < ~/Desktop/MyPasswordFile.txt
8021
[-import8021xProfiles service path]
[-export8021xProfiles service path yes | no]
使用示例：
$ networksetup -import8021xProfiles Ethernet "/Users/MyHome/Downloads/ExportedCon-
figs.networkconnect"
方法详细说明
-listnetworkserviceorder
Displays a list of network services in the order they are contacted for a connec-
tion, along with the corresponding port and device for each. An asterisk (*) next to
a service means the service is inactive.
-listallnetworkservices
Displays a list of all the network services on the server's hardware ports. An
asterisk (*) denotes that a network service is disabled.
-listallhardwareports
Displays list of hardware ports with corresponding device name and ethernet address.
-detectnewhardware
Detects new network hardware and creates a default network service on the hardware.
-getmacaddress hardwareport
Displays ethernet (or Wi-Fi) address for hardwareport or device specified.
-getcomputername
Displays the computer name.
-setcomputername computername
Sets computer name to . This name is used by AFP.
-getinfo networkservice
Displays the IP address, subnet mask, router, and hardware address for the that you specify.
-setmanual networkservice ip subnet router
Set the TCP/IP configuration for to manual with IP address set to
, Subnet Mask set to , and Router address set to .
-setdhcp networkservice [clientid]
Use this command to set the TCP/IP configuration for the specified
to use DHCP. The client ID is optional. Specify "Empty" for [clientid] to clear the
DHCP client id.
-setbootp networkservice
Use this command to set the TCP/IP configuration for the specified
to use BOOTP.
-setmanualwithdhcprouter networkservice ip
Use this command to specify a manual IP address to use for DHCP for the specified
.
-getadditionalroutes networkservice
Use this command to display the list of additional IPv4 routes configured for the
service.
-setadditionalroutes networkservice [dest1 mask1 gate1] [dest2 mask2 gate2] ... [destN maskN
gateN]
Use this command to set the list of IPv4 additional routes configured for the ser-
vice. Each route is specified as a (destination address, subnet mask, gateway
address) tuple. Specifying no tuples clears the list of routes.
-setv4off networkservice
Use this command to turn IPv4 off on the specified .
-setv6off networkservice
Use this command to turn IPv6 off on the specified .
-setv6automatic networkservice
Use this command to set IPv6 to get its addresses automatically for .
-setv6linklocal networkservice
Use this command to set IPv6 to only use link local for .
-setv6manual ip prefixlength router
Use this command to set IPv6 to get its addresses manually for .
Specify the ip address, the prefix length and the router.
-getv6additionalroutes networkservice
Use this command to display the list of additional IPv6 routes configured for the
service.
-setv6additionalroutes networkservice [dest1 prefixlength1 gate1] [dest2 prefixlength2
gate2] ... [destN prefixlengthN gateN]
Use this command to set the list of additional routes configured for the service.
Each route is specified as a
(destination address, prefix length, gateway address) tuple. Specifying no tuples
clears the list of routes.
-getdnsservers networkservice
Displays DNS info for .
-setdnsservers networkservice dns1 [dns2] [...]
Use this command to specify the IP addresses of servers you want the specified to use to resolve domain names. You can list any number of servers
(replace dns1, dns2, and so on with the IP addresses of domain name servers). If you
want to clear all DNS entries for the specified network service, type "empty" in
place of the DNS server names.
-getsearchdomains networkservice
Displays Domain Name info for .
-setsearchdomains networkservice domain1 [domain2] [...]
Use this command to designate the search domain for the specified .
You can list any number of search domains (replace domain1, domain2, and so on with
the name of a local domain). If you want to clear all search domain entries for the
specified network service, type aemptya in place of the domain name.
-create6to4service -
Use this command to create a new 6 to 4 service with name .
-set6to4automatic -
Use this command to set the 6 to 4 service such that it will get the relay address
automatically.
-set6to4manual - -
Use this command to set the 6 to 4 service such that it will get the relay address
manually. Specify the that you would like to set.
-getftpproxy networkservice
Displays FTP proxy (server, port, enabled value) info for .
-setftpproxy networkservice domain portnumber authenticated username password
Set FTP proxy for with and . Turns proxy on.
Optionally, specify or for to enable and disable authen-
ticated proxy support. Specify and if you turn authenticated
proxy support on.
-setftpproxystate networkservice on | off
Set FTP proxy on to either or .
-getwebproxy networkservice
Displays Web proxy (server, port, enabled value) info for .
-setwebproxy networkservice domain portnumber authenticated username password
Set Web proxy for with and . Turns proxy on.
Optionally, specify or for to enable and disable authen-
ticated proxy support. Specify and if you turn authenticated
proxy support on.
-setwebproxystate networkservice on | off
Set Web proxy on to either or .
-getsecurewebproxy networkservice
Displays Secure Web proxy (server, port, enabled value) info for .
-setsecurewebproxy networkservice domain portnumber authenticated username password
Set Secure Web proxy for with and . Turns
proxy on. Optionally, specify or for to enable and dis-
able authenticated proxy support. Specify and if you turn
authenticated proxy support on.
-setsecurewebproxystate networkservice on | off
Set SecureWeb proxy on to either or .
-setstreamingproxy networkservice domain portnumber authenticated username password
Set Streaming proxy for with . Turns proxy on.
Optionally, specify or for to enable and disable authen-
ticated proxy support. Specify and if you turn authenticated
proxy support on.
-setstreamingproxystate networkservice on | off
Set Streamingproxy on to either or .
-getgopherproxy networkservice
Displays Gopher proxy (server, port, enabled value) info for .
-setgopherproxy networkservice domain portnumber authenticated username password
Set Gopher proxy for with and . Turns proxy
on. Optionally, specify or for to enable and disable
authenticated proxy support. Specify and if you turn authenti-
cated proxy support on.
-setgopherproxystate networkservice on | off
Set Gopher proxy on to either or .
-getsocksfirewallproxy networkservice
Displays SOCKS Firewall proxy (server, port, enabled value) info for .
-setsocksfirewallproxy networkservice domain portnumber authenticated username password
Set SOCKS Firewall proxy for with and . Turns
proxy on. Optionally, specify or for to enable and dis-
able authenticated proxy support. Specify and if you turn
authenticated proxy support on.
-setsocksfirewallproxystate networkservice on | off
Set SOCKS Firewall proxy to either or .
-getproxybypassdomains networkservice
Displays Bypass Domain Names for .
-setproxybypassdomains networkservice domain1 [domain2] [...]
Set the Bypass Domain Name Servers for to [domain2]
[...]. Any number of Domain Name servers can be specified. Specify "Empty" for
to clear all Domain Name entries.
-getproxyautodiscovery networkservice
Displays Proxy Auto Discover for .
-getpassiveftp networkservice
Displays whether Passive FTP is on or off for .
-setpassiveftp networkservice on | off
Set Passive FTP to either or .
-setautoproxyurl networkservice url
Set proxy auto-config to url for and enable it.
-getautoproxyurl networkservice
Displays proxy auto-config (url, enabled) info for .
-setsocksfirewallproxystate networkservice on | off
Set SOCKS Firewall proxy to either or .
-getairportnetwork hardwareport
Displays current Wi-Fi Network.
-setairportnetwork hardwareport network [password]
Set Wi-Fi Network to using optional [password] if specified.
-getairportpower hardwareport
Displays whether Wi-Fi power is on or off.
-setairportpower hardwareport on | off
Set Wi-Fi power to either or .
-listpreferredwirelessnetworks hardwareport
List the preferred wireless networks for
-addpreferredwirelessnetworkatindex hardwareport network index securitytype [password]
Add wireless network named to preferred list for at
. Store the optional password in the keychain For security type, use OPEN for
none, WPA for WPA Personal, WPA2 for WPA2 Personal, WPA/WPA2 for WPA/WPA2 Personal,
WPAE for WPA Enterprise, WPA2E for WPA2 Enterprise, WPAE/WPA2E for WPA/WPA2 Enter-
prise, WEP for plain WEP, and 8021XWEP for 802.1X WEP.
-removepreferredwirelessnetwork hardwareport network
Remove from the preferred wireless network list for
-removeallpreferredwirelessnetworks hardwareport
Remove all networks from the preferred wireless network list for
-getnetworkserviceenabled networkservice
Displays whether a service is on or off (enabled or disabled).
-setnetworkserviceenabled networkservice on | off
Use this command to turn the specified network service on or off (enable or dis-
able).
-createnetworkservice networkservicename hardwareport
Create a service named on port . The new service will
be enabled by default.
-renamenetworkservice networkservice newnetworkservicename
Use this command to rename the specified network service to
.
-duplicatenetworkservice networkservice newnetworkservicename
Use this command to duplicate an existing network service and
rename it to the specified name .
-removenetworkservice networkservice
Use this command to delete a network service . You cannot use this
command to delete the last remaining service for a hardware port. To do so, you use
the -setnetworkserviceenabled command.
-ordernetworkservices service1 [service2] [service3] [...]
Use this command to designate the order network services are contacted on the speci-
fied hardware port. Name the network you want contacted first, then the second, and
so on. Use "listnetworkserviceorder" to view current service order. Note: use quotes
around service names which contain spaces (ie. "Built-in Ethernet").
-setMTUAndMediaAutomatically hardwarePort
Set hardwareport or device specified back to automatically setting the MTU and
Media.
-getMTU hardwareport
Get the MTU value for hardwareport or device specified.
-setMTU hardwarePort value
Set MTU for hardwareport or device specified.
-listValidMTURange hardwareport
List the valid MTU range for hardwareport or device specified.
-getMedia hardwareport
Show both the current setting for media and the active media on hardwareport or
device specified.
-setMedia hardwareport subtype [option1] [option2] [...]
Set media for hardwareport or device specified to subtype. Specify optional
[option1] and additional options depending on subtype. Any number of valid options
can be specified.
-listValidMedia hardwareport
List valid media options for hardwareport or device name. Enumerates available sub-
types and options per subtype.
-createVLAN name parentdevice tag
Create a VLAN with the name over the parent device and with
the tag .
-deleteVLAN name parentdevice tag
Delete the VLAN with the name over the parent device and with
the tag .
-listVLANs
List the VLANs that have been created.
-listdevicesthatsupportVLAN
List the devices that support VLANs.
-isBondSupported device
Displays YES if the device can be added to a bond. NO if it cannot.
-createBond name [device1] [device2] [...]
Create a bond with the user-defined-name name and optionally add any listed devices
if they support bonding.
-deleteBond bond
Delete the bond with the specified device-name.
-addDeviceToBond device bond
Add device to bond.
-removeDeviceFromBond device bond
Remove device from bond.
-listBonds
List of all bonds.
-showBondStatus bond
Display the status of the specified bond.
-listpppoeservices
List all PPPoE services in the current set.
-showpppoestatus name
Display the status of the PPPoE service with the specified name.
-createpppoeservice device name account password [pppoeName]
Create a PPPoE service on the specified device with the service name specified.
-deletepppoeservice service
Delete the service.
-setpppoeaccountname service account
Set the account name for the service.
-setpppoepassword service password
Set the password for the service.
-connectpppoeservice service
Connect the service.
-disconnectpppoeservice service
Disconnect the service.
-listlocations
List all network locations.
-getcurrentlocation
Display the name of the current set.
-createlocation location [populate]
Create a set with the user-defined-name name and optionally populate it with the
default services.
-deletelocation location
Delete the set.
-switchtolocation location
Make the specified set the current set.
-listalluserprofiles
Display the names of all of the user profiles.
-listloginprofiles service
Display the names of the loginwindow profiles for the specified service.
-enablesystemprofile service on | off
Enables or disables the system profile for the specified service.
-enableloginprofile service profile on | off
Enables or disables the specified loginwindow profile for the specified ser-
vice.
-enableuserprofile profile on | off
Enables or disables the specified user profile.
-import8021xProfiles service path
Imports the 802.1x profiles for the specified service.
-export8021xProfiles service path yes | no
Exports all of the profiles for the specified service and optionally includes the
items from the keychain.
-export8021xUserProfiles path yes | no
Exports only the user profiles and optionally includes the items from the key-
chain.
-export8021xLoginProfiles service path yes | no
Exports only the loginwindow profiles for the specified service and optionally
includes the items from the keychain.
-export8021xSystemProfile service path yes | no
Exports only the system profile for the specified service and optionally includes
the items from the keychain.
-settlsidentityonsystemprofile service path passphrase
Sets the TLS identity on the system profile for the specified service. Identity must
be a pkcs12 file.
-settlsidentityonuserprofile profile path passphrase
Sets the TLS identity on the specified user profile. Identity must be a pkcs12 file.
-deletesystemprofile service
Deletes the system profile for the specified service.
-deleteloginprofile service profile
Deletes the specified loginwindow profile for the specified service.
-deleteuserprofile profile
Deletes the specified user profile. Displays version of networksetup tool.
-help Displays a list of all the commands available in the Network Setup Tool, with
explanatory information.
-printcommands
Displays a list of commands with no detail.
-isBondSupported device
Displays YES if the device can be added to a bond. NO if it cannot.
-createBond name [device1] [device2] [...]
Create a bond with the user-defined-name name and optionally add any listed devices
if they support bonding.
-deleteBond bond
Delete the bond with the specified device-name.
-addDeviceToBond device bond
Add device to bond.
-removeDeviceFromBond device bond
Remove device from bond.