Linux 查看系统硬件信息(实例详解)
linux查看系统的硬件信息，并不像windows那么直观，这里我罗列了查看系统信息的实用命令，并做了分类，实例解说。
cpu
lscpu命令，查看的是cpu的统计信息.
blue@blue-pc:~$ lscpu Architecture: i686 #cpu架构 CPU op-mode(s): 32-bit, 64-bit Byte Order: Little Endian #小尾序 CPU(s): 4 #总共有4核 On-line CPU(s) list: 0-3Thread(s) per core: 1 #每个cpu核，只能支持一个线程，即不支持超线程 Core(s) per socket: 4 #每个cpu，有4个核 Socket(s): 1 #总共有1一个cpu Vendor ID: GenuineIntel #cpu产商 intel CPU family: 6Model: 42Stepping: 7CPU MHz: 1600.000BogoMIPS: 5986.12Virtualization: VT-x #支持cpu虚拟化技术 L1d cache: 32K L1i cache: 32K L2 cache: 256K L3 cache: 6144K
查看/proc/cpuinfo,可以知道每个cpu信息，如每个CPU的型号，主频等。
#cat /proc/cpuinfo processor : 0vendor_id : GenuineIntel cpu family : 6model : 42model name : Intel(R) Core(TM) i5-2320 CPU @ 3.00GHz .....
上面输出的是第一个cpu部分信息，还有3个cpu信息省略了。
内存
概要查看内存情况
free -m total used free shared buffers cached Mem: 3926 3651 274 0 12 404-/+ buffers/cache: 3235 691Swap: 9536 31 9505
这里的单位是MB，总共的内存是3926MB。
查看内存详细使用
# cat /proc/meminfo MemTotal: 4020868 kB MemFree: 230884 kB Buffers: 7600 kB Cached: 454772 kB SwapCached: 836 kB .....
查看内存硬件信息
dmidecode -t memory # dmidecode 2.11SMBIOS 2.7 present. Handle 0x0008, DMI type 16, 23 bytes Physical Memory Array Location: System Board Or Motherboard .... Maximum Capacity: 32 GB .... Handle 0x000A, DMI type 17, 34 bytes .... Memory Device Array Handle: 0x0008 Error Information Handle: Not Provided Total Width: 64 bits Data Width: 64 bits Size: 4096 MB .....
我的主板有4个槽位，只用了一个槽位，上面插了一条4096MB的内存。
磁盘
查看硬盘和分区分布
# lsblk NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT sda 8:0 0 465.8G 0 disk ├─sda1 8:1 0 1G 0 part /boot ├─sda2 8:2 0 9.3G 0 part [SWAP] ├─sda3 8:3 0 74.5G 0 part /├─sda4 8:4 0 1K 0 part ├─sda5 8:5 0 111.8G 0 part /home └─sda6 8:6 0 269.2G 0 part
显示很直观
如果要看硬盘和分区的详细信息
# fdisk -l Disk /dev/sda: 500.1 GB, 500107862016 bytes255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x00023728 Device Boot Start End Blocks Id System/dev/sda1 * 2048 2148351 1073152 83 Linux/dev/sda2 2148352 21680127 9765888 82 Linux swap / Solaris/dev/sda3 21680128 177930239 78125056 83 Linux/dev/sda4 177932286 976771071 399419393 5 Extended/dev/sda5 177932288 412305407 117186560 83 Linux/dev/sda6 412307456 976771071 282231808 83 Linux
网卡
查看网卡硬件信息
# lspci | grep -i 'eth'02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06)
查看系统的所有网络接口
# ifconfig -a eth0 Link encap:以太网 硬件地址 b8:97:5a:17:b3:8f ..... lo Link encap:本地环回 .....
或者是
ip link show1: lo: <LOOPBACK> mtu 16436 qdisc noqueue state DOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:002: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000link/ether b8:97:5a:17:b3:8f brd ff:ff:ff:ff:ff:ff
如果要查看某个网络接口的详细信息，例如eth0的详细参数和指标
# ethtool eth0 Settings for eth0: Supported ports: [ TP MII ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Half 1000baseT/Full #支持千兆半双工，全双工模式 Supported pause frame use: No Supports auto-negotiation: Yes #支持自适应模式，一般都支持 Advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Half 1000baseT/Full Advertised pause frame use: Symmetric Receive-only Advertised auto-negotiation: Yes #默认使用自适应模式 Link partner advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full ..... Speed: 100Mb/s #现在网卡的速度是100Mb,网卡使用自适应模式，所以推测路由是100Mb，导致网卡从支持千兆，变成要支持百兆 Duplex: Full #全双工 ..... Link detected: yes #表示有网线连接，和路由是通的
其他
查看pci信息，即主板所有硬件槽信息。
lspci00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) #主板芯片00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) #显卡00:14.0 USB controller: Intel Corporation Panther Point USB xHCI Host Controller (rev 04) #usb控制器00:16.0 Communication controller: Intel Corporation Panther Point MEI Controller #1 (rev 04)00:1a.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #2 (rev 04)00:1b.0 Audio device: Intel Corporation Panther Point High Definition Audio Controller (rev 04) #声卡00:1c.0 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 1 (rev c4) #pci 插槽00:1c.2 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 3 (rev c4)00:1c.3 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 4 (rev c4)00:1d.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #1 (rev 04)00:1f.0 ISA bridge: Intel Corporation Panther Point LPC Controller (rev 04)00:1f.2 IDE interface: Intel Corporation Panther Point 4 port SATA Controller [IDE mode] (rev 04) #硬盘接口00:1f.3 SMBus: Intel Corporation Panther Point SMBus Controller (rev 04)00:1f.5 IDE interface: Intel Corporation Panther Point 2 port SATA Controller [IDE mode] (rev 04) #硬盘接口02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06) #网卡03:00.0 PCI bridge: Integrated Technology Express, Inc. Device 8893 (rev 41)
如果要更详细的信息:lspci -v 或者 lspci -vv
如果要看设备树:lscpi -t
查看bios信息
# dmidecode -t bios ...... BIOS Information Vendor: American Megatrends Inc. Version: 4.6.5 Release Date: 04/25/2012 ....... BIOS Revision: 4.6......
dmidecode以一种可读的方式dump出机器的DMI(Desktop Management Interface)信息。这些信息包括了硬件以及BIOS，既可以得到当前的配置，也可以得到系统支持的最大配置，比如说支持的最大内存数等。
如果要查看所有有用信息
dmidecode -q
里面包含了很多硬件信息。