cisco 2960g ip&mac&port绑定(2)
Switch#
Switch#
Switch#sh access-list
Standard IP access list IP01
10 permit 200.73.91.56
Standard IP access list IP32
10 permit 200.73.91.62
Switch#sh int g0/1
GigabitEthernet0/1 is up, line protocol is up (connected)
Hardware is Gigabit Ethernet, address is 0022.0d5d.ec81 (bia 0022.0d5d.ec81)
Description: x4(rhe5,x4200)
MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 1000Mb/s, media type is 10/100/1000BaseTX
input flow-control is off, output flow-control is unsupported
ARP type:
ARPA, ARP Timeout 04:00:00
Last input never, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 1000 bits/sec, 1 packets/sec
5 minute output rate 1000 bits/sec, 2 packets/sec
492917 packets input, 273364397 bytes, 0 no buffer
Received 22837 broadcasts (0 multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog(??), 20 multicast, 0 pause input
0 input packets with dribble condition detected
901449 packets output, 267242819 bytes, 0 underruns
0 output errors, 0 collisions, 1 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 PAUSE output
0 output buffer failures, 0 output buffers swapped out
Switch#
Switch#sh ip int g0/1
GigabitEthernet0/1 is up, line protocol is up
Inbound access list is IP01
Switch#
Switch#sh ip int g0/48
GigabitEthernet0/48 is up, line protocol is up
Inbound access list is not set
Switch#
Switch#sh int g0/1 ?
accounting Show interface accounting
capabilities Show interface capabilities information
controller Show interface status, configuration and controller status
counters Show interface counters
crb Show interface routing/bridging info
dampening Show interface dampening info
debounce Show interface debounce time info
description Show interface description
etherchannel Show interface etherchannel information
fair-queue Show interface Weighted Fair Queueing (WFQ) info
flowcontrol Show interface flowcontrol information
irb Show interface routing/bridging info
mac-accounting Show interface MAC accounting info
mpls-exp Show interface MPLS experimental accounting info
mtu Show interface mtu
precedence Show interface precedence accounting info
private-vlan Show interface private vlan information
pruning Show interface trunk VTP pruning information
random-detect Show interface Weighted Random Early Detection (WRED) info
rate-limit Show interface rate-limit info
stats Show interface packets & octets, in & out, by switching path
status Show interface line status
summary Show interface summary
switchport Show interface switchport information
transceiver Show interface transceiver
trunk Show interface trunk information
vlan Show interface vlan information
| Output modifiers
<cr>
Switch#
Switch#sh vlan
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Gi0/47
5 VLAN0005 active Gi0/1, Gi0/2, Gi0/3, Gi0/4, Gi0/5, Gi0/6, Gi0/7, Gi0/8, Gi0/9, Gi0/10
Gi0/11, Gi0/12, Gi0/13, Gi0/14, Gi0/15, Gi0/16, Gi0/17, Gi0/18, Gi0/19
Gi0/20, Gi0/21, Gi0/22, Gi0/23, Gi0/24, Gi0/25, Gi0/26, Gi0/27, Gi0/28
Gi0/29, Gi0/30, Gi0/31, Gi0/32, Gi0/33, Gi0/34, Gi0/35, Gi0/36, Gi0/37
Gi0/38, Gi0/39, Gi0/40, Gi0/41, Gi0/42, Gi0/43, Gi0/44, Gi0/45, Gi0/46
1002 fddi-default act/unsup
1003 token-ring-default act/unsup
1004 fddinet-default act/unsup
1005 trnet-default act/unsup
VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
1 enet 100001 1500 - - - - - 0 0
5 enet 100005 1500 - - - - - 0 0
1002 fddi 101002 1500 - - - - - 0 0
1003 tr 101003 1500 - - - - - 0 0
1004 fdnet 101004 1500 - - - ieee - 0 0
1005 trnet 101005 1500 - - - ibm - 0 0
Remote SPAN VLANs
------------------------------------------------------------------------------
Primary Secondary Type Ports
------- --------- ----------------- ------------------------------------------
Switch#
Switch(config)#int g0/9
Switch(config-if)#?
Interface configuration commands:
arp Set arp type (arpa, probe, snap) or timeout
auto Configure Automation
bandwidth Set bandwidth informational parameter
carrier-delay Specify delay for interface transitions
cdp CDP interface subcommands
channel-group Etherchannel/port bundling configuration
channel-protocol Select the channel protocol (LACP, PAgP)
dampening
Enable event dampening
default Set a command to its defaults
delay Specify interface throughput delay
description Interface specific description
dot1x Interface Config Commands for IEEE 802.1X
down-when-looped Force looped interface down
duplex Configure duplex operation.
ethernet Ethernet interface parameters
exit Exit from interface configuration mode
flowcontrol Configure flow operation.
help Description of the interactive help system
hold-queue Set hold queue depth
ip Interface Internet Protocol config commands
keepalive Enable keepalive
lacp LACP interface subcommands
link Configure Link
load-interval Specify interval for load calculation for an interface
logging Configure logging for interface
mac MAC interface commands
macro Command macro
max-reserved-bandwidth Maximum Reservable Bandwidth on an Interface
mdix Set Media Dependent Interface with Crossover
mls mls interface commands
mvr MVR per port configuration
no Negate a command or set its defaults
pagp PAgP interface subcommands
priority-queue Priority Queue
queue-set Choose a queue set for this queue
rmon Configure Remote Monitoring on an interface
service-policy Configure QoS Service Policy
shutdown Shutdown the selected interface
snmp Modify SNMP interface parameters
source Get config from another source
spanning-tree Spanning Tree Subsystem
speed Configure speed operation.
srr-queue Configure shaped round-robin transmit queues
storm-control storm configuration
switchport Set switching mode characteristics
timeout Define timeout values for this interface
transmit-interface Assign a transmit interface to a receive-only interface
tx-ring-limit Configure PA level transmit ring limit
udld Configure UDLD enabled or disabled and ignore global UDLD setting
Switch(config)#
Switch(config)#exit
Switch#