广播多路访问链路上的ospf
广播多路访问链路上的
OSPF
一、
实验目的
1、
修改参考带宽
2、
DR
选举的控制
3、
广播多路访问链路上的
ospf
特征
4、
Hello
间隔对邻接关系的影响
二、
实验拓扑
三、
实验步骤
R1
R1(config-if)#router ospf 1
R1(config-router)#router-id 1.1.1.1
R1(config-router)#network 1.1.1.0 255.255.255.0 a 0
R1(config-router)#net 192.168.1.0 255.255.255.0 a 0
R1(config-router)#auto-cost reference-bandwidth 1000
R2
R2(config-if)#router ospf 1
R2(config-router)#router-id 2.2.2.2
R2(config-router)#net 192.168.1.0 255.255.255.0 a 0
R2(config-router)#net 2.2.2.0 255.255.255.0 a 0
R2(config-router)#auto-cost reference-bandwidth 1000
R3
R3(config-if)#router ospf 1
R3(config-router)#router-id 3.3.3.3
R3(config-router)#network 192.168.1.0 255.255.255.0 a 0
R3(config-router)#net 3.3.3.0 255.255.255.0 a 0
R3(config-router)#auto-cost reference-bandwidth 1000
R4
R4(config-if)#router ospf 1
R4(config-router)#router-id 4.4.4.4
R4(config-router)#net 192.168.1.0 255.255.255.0 a 0
R4(config-router)#net 4.4.4.0 255.255.255.0 a 0
R4(config-router)#auto-cost reference-bandwidth 1000
说明：
Auto-cost reference-bandwidth
要在所有
ospf
路由器上配置，目的是确保参数标准相同。
R4(config-if)#do show ip ospf neighbor
Neighbor ID Pri State Dead Time Address Interface
1.1.1.1 1 2WAY/DROTHER 00:00:30 192.168.1.1 Ethernet1/1
2.2.2.2 1 FULL/DR 00:00:33 192.168.1.2 Ethernet1/1
3.3.3.3 1 FULL/BDR 00:00:35 192.168.1.3 Ethernet1/1
注意
邻居关系和邻接关系是不一样的，邻居关系是指达到
2WAY
状态的两台路由器，而邻接关系是达到
FULL
状态的两台路由器。
EIGRP
和
OSPF
建立邻接关系的要求
|
要求
|
OSPF
|
EIGRP
|
|
接口的主
IP
地址必须属于同一子网
|
是
|
是
|
|
连接的接口不能处于被动状态
|
是
|
是
|
|
必须位于同一个区域
|
是
|
N/A
|
|
Hello
间隔
/
定时器以及保持定时器（
EIGRP
）或失效定时器（
OSPF
）必须相同
|
是
|
否
|
|
路由器
ID
必须是唯一的
|
是
|
否
|
|
必须通过邻居的身分验证（如果配置）
|
是
|
是
|
|
用于计算度量值的
K
值必须相同
|
N/A
|
是
|
|
必须在配置命令
router
中使用了相同的
ASN(EIGRP)
或进程（
OSPF
）
|
否
|
是
|
|
IP MTU
必须相同（
MTU
）不同可能导致无法交换拓扑数据
|
是
|
否
|
修改
Hello-interval
R4(config-if)#ip ospf hello-interval 8
R4(config-if)#do show ip ospf int e1/1
Ethernet1/1 is up, line protocol is up
Internet Address 192.168.1.4/24, Area 0
Process ID 1, Router ID 4.4.4.4, Network Type BROADCAST, Cost: 100
Transmit Delay is 1 sec, State DROTHER, Priority 1
Designated Router (ID) 2.2.2.2, Interface address 192.168.1.2
Backup Designated router (ID) 3.3.3.3, Interface address 192.168.1.3
Timer intervals configured, Hello 8, Dead 32, Wait 32, Retransmit 5
oob-resync timeout 40
Hello due in 00:00:00
Supports Link-local Signaling (LLS)
Index 2/2, flood queue length 0
Next 0x0(0)/0x0(0)
Last flood scan length is 0, maximum is 1
Last flood scan time is 0 msec, maximum is 4 msec
Neighbor Count is 3, Adjacent neighbor count is 2
Adjacent with neighbor 2.2.2.2 (Designated Router)
Adjacent with neighbor 3.3.3.3 (Backup Designated Router)
Suppress hello for 0 neighbor(s)
R4(config-if)#
*Mar 1 00:51:42.235: %OSPF-5-ADJCHG: Process 1, Nbr 3.3.3.3 on Ethernet1/1 from FULL to DOWN, Neighbor Down: Dead timer expired
R4(config-if)#
*Mar 1 00:51:47.671: %OSPF-5-ADJCHG: Process 1, Nbr 1.1.1.1 on Ethernet1/1 from EXSTART to DOWN, Neighbor Down: Dead timer expired
R4(config-if)#
*Mar 1 00:51:51.003: %OSPF-5-ADJCHG: Process 1, Nbr 2.2.2.2 on Ethernet1/1 from FULL to DOWN, Neighbor Down: Dead timer expired
R4
的邻接关系中断了，因为
Hello
定时器和失效定时器不匹配，然而，仅当失效定时器到期后邻接关系才中断。
R4(config-if)#ip ospf dead-interval 40
可修改失效定时器。
OSPF
邻接关系建立过程中，接口状态的变化包括
DOWN
，
2WAY
，
EXSTART
，
EXCHANGE
，
Loading
和
FULL
。
*Mar 1 01:20:54.219: OSPF: Neighbor change Event on interface Ethernet1/1
*Mar 1 01:20:54.219: OSPF: DR/BDR election on Ethernet1/1
*Mar 1 01:20:54.219: OSPF: Elect BDR 0.0.0.0
*Mar 1 01:20:54.219: OSPF: Elect DR 4.4.4.4
*Mar 1 01:20:54.219: DR: 4.4.4.4 (Id) BDR: none
*Mar 1 01:20:54.223: OSPF: 4.4.4.4 address 192.168.1.4 on Ethernet1/1 is dead, state DOWN
*Mar 1 01:20:54.223: %OSPF-5-ADJCHG: Process 1, Nbr 4.4.4.4 on Ethernet1/1 from FULL to DOWN, Neighbor Down: Interface down or detached
*Mar 1 01:20:54.227: OSPF: Neighbor change Event on interface Ethernet1/1
*Mar 1 01:20:54.231: OSPF: DR/BDR election on Ethernet1/1
*Mar 1 01:20:54.231: OSPF: Elect BDR 0.0.0.0
*Mar 1 01:20:54.231: OSPF: Elect DR 0.0.0.0
*Mar 1 01:20:54.231: DR: none
R1# BDR: none
*Mar 1 01:20:54.231: OSPF: Remember old DR 4.4.4.4 (id)
*Mar 1 01:20:54.231: OSPF: Interface Loopback0 going Down
*Mar 1 01:20:54.235: OSPF: 1.1.1.1 address 1.1.1.1 on Loopback0 is dead, state DOWN
*Mar 1 01:20:54.299: OSPF: Interface Ethernet1/1 going Up
*Mar 1 01:20:54.303: OSPF: Interface Loopback0 going Up
*Mar 1 01:20:54.715: OSPF: Build router LSA for area 0, router ID 1.1.1.1, seq 0x80000001
R1#
*Mar 1 01:21:00.031: OSPF: 2 Way Communication to 2.2.2.2 on Ethernet1/1, state 2WAY
*Mar 1 01:21:01.175: OSPF: 2 Way Communication to 3.3.3.3 on Ethernet1/1, state 2WAY
*Mar 1 01:21:01.179: OSPF: Backup seen Event before WAIT timer on Ethernet1/1
*Mar 1 01:21:01.183: OSPF: DR/BDR election on Ethernet1/1
*Mar 1 01:21:01.183: OSPF: Elect BDR 3.3.3.3
*Mar 1 01:21:01.183: OSPF: Elect DR 3.3.3.3
*Mar 1 01:21:01.187: DR: 3.3.3.3 (Id) BDR: 3.3.3.3 (Id)
*Mar 1 01:21:01.191: OSPF: Send DBD to 3.3.3.3 on Ethernet1/1 seq 0x26CE opt 0x52 flag 0x7 len 32
*Mar 1 01:21:01.303: OSPF: Rcv DBD from 3.3.3.3 on Ethernet1/1 seq 0x16A5 opt 0x52 flag 0x7 len 32 mtu 1500 state EXSTART
*Mar 1 01:21:01.307: OSPF: Nbr 3.3.3.3 has larger interface MTU
*Mar 1 01:21:01.391: OSPF: 2 Way Communication to 4.4.4.4 on Ethernet1/1, state 2WAY
*Mar 1 01:22:21.251: OSPF: Send DBD to 3.3.3.3 on Ethernet1/1 seq 0x26CE opt 0x52 flag 0x7 len 32
*Mar 1 01:22:21.255: OSPF: Retransmitting DBD to 3.3.3.3 on Ethernet1/1 [16]
*Mar 1 01:22:21.259: OSPF: Rcv DBD from 3.3.3.3 on Ethernet1/1 seq 0x16A5 opt 0x52 flag 0x7 len 32 mtu 1500 state EXSTART
*Mar 1 01:22:21.263: OSPF: Nbr 3.3.3.3 has larger interface MTU
*Mar 1 01:22:21.443: OSPF: Rcv DBD from 4.4.4.4 on Ethernet1/1 seq 0x2477 opt 0x52 flag 0x7 len 32 mtu 1498 state EXSTART
*Mar 1 01:22:21.447: OSPF: Nbr 4.4.4.4 has larger interface MTU
*Mar 1 01:22:21.483: OSPF: Send DBD to 4.4.4.4 on Ethernet1/1 seq 0x181D opt 0x52 flag 0x7 len 32
*Mar 1 01:25:56.451: OSPF: Rcv DBD from 4.4.4.4 on Ethernet1/1 seq 0x1F2F opt 0x52 flag 0x7 len 32 mtu 1498 state EXCHANGE
*Mar 1 01:25:56.455: OSPF: Nbr 4.4.4.4 has smaller interface MTU
*Mar 1 01:25:56.459: OSPF: Send DBD to 4.4.4.4 on Ethernet1/1 seq 0x1F2F opt 0x52 flag 0x2 len 132
R1#
*Mar 1 01:26:01.471: OSPF: Rcv DBD from 4.4.4.4 on Ethernet1/1 seq 0x1F2F opt 0x52 flag 0x7 len 32 mtu 1498 state EXCHANGE
*Mar 1 01:26:01.475: OSPF: Nbr 4.4.4.4 has smaller interface MTU
*Mar 1 01:26:01.479: OSPF: Send DBD to 4.4.4.4 on Ethernet1/1 seq 0x1F2F opt 0x52 flag 0x2 len 132
R1#
*Mar 1 01:26:06.447: OSPF: Rcv DBD from 4.4.4.4 on Ethernet1/1 seq 0x1F2F opt 0x52 flag 0x7 len 32 mtu 1498 state EXCHANGE
*Mar 1 01:26:06.451: OSPF: Nbr 4.4.4.4 has smaller interface MTU
*Mar 1 01:26:06.455: OSPF: Send DBD to 4.4.4.4 on Ethernet1/1 seq 0x1F2F opt 0x52 flag 0x2 len 132
R1#
*Mar 1 01:26:11.431: OSPF: Rcv DBD from 4.4.4.4 on Ethernet1/1 seq 0x1F2F opt 0x52 flag 0x7 len 32 mtu 1498 state EXCHANGE
*Mar 1 01:26:11.435: OSPF: Nbr 4.4.4.4 has smaller interface MTU
*Mar 1 01:26:11.439: OSPF: Send DBD to 4.4.4.4 on Ethernet1/1 seq 0x1F2F opt 0x52 flag 0x2 len 132
修改
MTU
的值为
1480
*Mar 1 01:24:51.303: OSPF: Rcv DBD from 3.3.3.3 on Ethernet1/1 seq 0x9DB opt 0x52 flag 0x7 len 32 mtu 1500 state EXSTART
*Mar 1 01:24:51.307: OSPF: Nbr 3.3.3.3 has larger interface MTU
在建立邻接关系时会提示
MTU
值不匹配。将不能时入
EXCHANGE
状态。