3A_tacacs认证

 

一、网络拓扑:
 

二、ACS配置:
1、添加用户test。
 

 
2、network configuration
 

 

 

 

 

 

 

 

三、cisco2950配置
1 、使用pc机的串口连接cisco 2950的console口
2 、使用超级终端(或CRT)连接串口
3 、进行交换机配置,命令如下:
//将端口1/2加入vlan1,设置vlan的IP
Switch#config
Switch#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#in
Switch(config)#interface vlan 1
Switch(config-if)#ip address 192.168.0.121 255.255.255.0
Switch(config-if)#no shut
Switch(config-if)#exit
Switch(config)#interface fastEthernet 0/1
Switch(config-if)#switchport mode access
Switch(config-if)#switchport access vlan 1
Switch(config)#interface fastEthernet 0/2
Switch(config-if)#sw
Switch(config-if)#switchport mode access
Switch(config-if)#switchport access vlan 1
Switch(config-if)#exit
Switch(config)#exit
Switch#
1d05h: %SYS-5-CONFIG_I: Configured from console by ikey on console
Switch#show ip interface brief
Interface                   IP-Address      OK? Method Status                Protocol
Vlan1                       192.168.0.118 YES manual up                    up     
FastEthernet0/1             unassigned      YES unset up                     up     
FastEthernet0/2             unassigned      YES unset down                  down   
FastEthernet0/3             unassigned      YES unset down                  down   
FastEthernet0/4             unassigned      YES unset down                  down   
FastEthernet0/5             unassigned      YES unset down                  down    
FastEthernet0/6             unassigned      YES unset down                  down   
FastEthernet0/7             unassigned      YES unset down                  down   
FastEthernet0/8             unassigned      YES unset down                  down   
FastEthernet0/9             unassigned      YES unset down                  down   
FastEthernet0/10            unassigned      YES unset down                  down   
FastEthernet0/11            unassigned      YES unset down                  down   
FastEthernet0/12            unassigned      YES unset down                  down   
FastEthernet0/13            unassigned      YES unset down                  down   
FastEthernet0/14            unassigned      YES unset down                  down   
FastEthernet0/15            unassigned      YES unset down                  down   
FastEthernet0/16            unassigned      YES unset down                  down   
FastEthernet0/17            unassigned      YES unset down                  down   
FastEthernet0/18            unassigned      YES unset down                  down   
FastEthernet0/19            unassigned      YES unset down                  down   
FastEthernet0/20            unassigned      YES unset down                  down   
FastEthernet0/21            unassigned      YES unset down                  down   
FastEthernet0/22            unassigned      YES unset down                  down   
FastEthernet0/23            unassigned      YES unset down                  down   
FastEthernet0/24            unassigned      YES unset down                  down  
 
//设置tacacs+认证
tacacs-server host 192.168.0.119
tacacs-server directed-request
tacacs-server key hahatest
enable secret cisco                                         ‘定义enable密码
aaa new-model                                            ‘启用AAA认证
aaa authentication login tac_auth tacacs+
aaa authentication login no_tacacs none
line con 0                               (此段表示通过con口管理时不进行radius认证)
login authentication no_tacacs
transport output none
exit
 
line vty 0 4                             (telnet)
login authentication tac_auth
 
 
 
4、使用pc机telnet到设置的vlan1 IP,输入认证服务器用户名和密码进行认证
 

本文出自 “people” 博客,转载请与作者联系!

你可能感兴趣的:(职场,休闲,3A_tacacs认证)