Note that commands marked with a * are not implemented in a number of FTP servers.
Aborts a file transfer currently in progress.
This command is used to send account information on systems that require it. Typically sent after a PASS command.
Allocates sufficient storage space to receive a file. If the maximum size of a record also needs to be known, that is sent as a second numeric parameter following a space, the capital letter "R", and another space.
Append data to the end of a file on the remote host. If the file does not already exist, it is created. This command must be preceded by a PORT or PASV command so that the server knows where to receive data from.
Makes the parent of the current directory be the current directory.
Makes the given directory be the current directory on the remote host.
Deletes the given file on the remote host.
If a command is given, returns help on that command; otherwise, returns general help for the FTP server (usually a list of supported commands).
If remote-filespec refers to a file, sends information about that file. If remote-filespec refers to a directory, sends information about each file in that directory. remote-filespecdefaults to the current directory. This command must be preceded by a PORT or PASV command.
Returns the last-modified time of the given file on the remote host in the format "YYYYMMDDhhmmss": YYYY is the four-digit year, MM is the month from 01 to 12, DD is the day of the month from 01 to 31, hh is the hour from 00 to 23, mm is the minute from 00 to 59, and ss is the second from 00 to 59.
Creates the named directory on the remote host.
Sets the transfer mode to one of:
Returns a list of filenames in the given directory (defaulting to the current directory), with no other information. Must be preceded by a PORT or PASV command.
Does nothing except return a response.
After sending the USER command, send this command to complete the login process. (Note, however, that an ACCT command may have to be used on some systems.)
Tells the server to enter "passive mode". In passive mode, the server will wait for the client to establish a connection with it rather than attempting to connect to a client-specified port. The server will respond with the address of the port it is listening on, with a message like:
227 Entering Passive Mode (a1,a2,a3,a4,p1,p2)
where a1.a2.a3.a4 is the IP address and p1*256+p2 is the port number.
Specifies the host and port to which the server should connect for the next file transfer. This is interpreted as IP address a1.a2.a3.a4, port p1*256+p2.
Returns the name of the current directory on the remote host.
Terminates the command connection.
Reinitializes the command connection - cancels the current user/password/account information. Should be followed by a USER command for another login.
Sets the point at which a file transfer should start; useful for resuming interrupted transfers. For nonstructured files, this is simply a decimal number. This command must immediately precede a data transfer command (RETR or STOR only); i.e. it must come after any PORT or PASV command.
Begins transmission of a file from the remote host. Must be preceded by either a PORT command or a PASV command to indicate where the server should send data.
Deletes the named directory on the remote host.
Used when renaming a file. Use this command to specify the file to be renamed; follow it with an RNTO command to specify the new name for the file.
Used when renaming a file. After sending an RNFR command to specify the file to rename, send this command to specify the new name for the file.
Executes a site-specific command.
Returns the size of the remote file as a decimal number.
If invoked without parameters, returns general status information about the FTP server process. If a parameter is given, acts like the LIST command, except that data is sent over the control connection (no PORT or PASV command is required).
Begins transmission of a file to the remote site. Must be preceded by either a PORT command or a PASV command so the server knows where to accept data from.
Begins transmission of a file to the remote site; the remote filename will be unique in the current directory. The response from the server will include the filename.
Sets the file structure for transfer to one of:
Returns a word identifying the system, the word "Type:", and the default transfer type (as would be set by the TYPE command). For example: UNIX Type: L8
Sets the type of file to be transferred. type-character can be any of:
Send this command to begin the login process. username should be a valid username on the system, or "anonymous" to initiate an anonymous login.
==============================================================
user_config_dir
这个强大的设置容许覆盖一些在手册页中指定的配置项(基于单个用户的)。用法很简单,最好结合范例。如果你把user_config_dir
改为/etc/vsftpd_user_conf,那么以chris登录,vsftpd将调用配置文件/etc/vsftpd_user_conf/chris。
默认值:无
系统Debug分析篇
1.调试命令
strace -p pid
2.跟踪指定进程的PID
gdb -p pid