​Cisco路由器交换机密码破解（小妞作品）

               Cisco路由器交换机密码破解（小妞作品）

路由器设备型号：2621XM

实验步骤：

Router>show version

…………………

cisco 2621XM (MPC860P) processor (revision 0x200) with 126976K/4096K bytes of memory.

Processor board ID JAE075202KQ (2960342124)

M860 processor: part number 5, mask 2

Bridging software.

X.25 software, Version 3.0.0.

2 FastEthernet/IEEE 802.3 interface(s)

4 Low-speed serial(sync/async) network interface(s)

32K bytes of non-volatile configuration memory.

32768K bytes of processor board System flash (Read/Write)

Configuration register is 0x2102

注意：0x2102 是指开机时加载配置文件

     0x2142 是指开机时不加载配置文件

断电重启，在超级终端里按下ctr+break键，进入画面（break键就是esc键）

            System Bootstrap, Version 12.2(8r) [cmong 8r], RELEASE SOFTWARE (fc1)

Copyright (c) 2003 by cisco Systems, Inc.

PC = 0xfff0ac3c, Vector = 0x500, SP = 0x680127c0

C2600 platform with 131072 Kbytes of main memory

PC = 0xfff0ac3c, Vector = 0x500, SP = 0x80004884

monitor: command "boot" aborted due to user interrupt

rommon 1 >

把寄存器值改成0x2142

rommon 1 > ?  

….

confreg             configuration register utility

…..

rommon 2 > confreg

          Configuration Summary

  (Virtual Configuration Register: 0x2102)

enabled are:

load rom after netboot fails

console baud: 9600

boot: image specified by the boot system commands

     or default to: cisco2-C2600

do you wish to change the configuration? y/n  [n]:  y

enable  "diagnostic mode"? y/n  [n]:  n

enable  "use net in IP bcast address"? y/n  [n]:  n

disable "load rom after netboot fails"? y/n  [n]:  n

enable  "use all zero broadcast"? y/n  [n]:  n

enable  "break/abort has effect"? y/n  [n]:  n

enable  "ignore system config info"? y/n  [n]:  y

change console baud rate? y/n  [n]:  n

change the boot characteristics? y/n  [n]:  n

          Configuration Summary

  (Virtual Configuration Register: 0x2142)

enabled are:

load rom after netboot fails

ignore system config info

console baud: 9600

boot: image specified by the boot system commands

     or default to: cisco2-C2600

do you wish to change the configuration? y/n  [n]:  

You must reset or power cycle for new config to take effect

rommon 3 >

用命令重启路由器

rommon 3 > reset

开机之后

Router>sh ver

Cisco Internetwork Operating System Software

………

Configuration register is 0x2142

Router#sh run 会发现是初始配置

Router#copy startup-config run

Destination filename [running-config]?

Slot is empty or does not support clock participate

WIC slot is empty or does not support clock participate

853 bytes copied in 0.956 secs (892 bytes/sec)

Router#sh run

Building configuration...

enable password xunbo

!

Router#config

Router(config)#no enable pass

Router(config)#end

Router#sh ru

Router# copy run start

Destination filename [startup-config]?

Building configuration...

[OK]

Router#conf t

Enter configuration commands, one per line.  End with CNTL/Z.

Router(config)#config 0x2102

Router(config)#end

这样重启之后只是删了密码，但是配置还在。

交换机型号2950系列

交换机与路由器不一样，与寄存器无关

准备工作：

Switch(config)#enable pass xunbo

Switch#copy run  start

Destination filename [startup-config]?

Building configuration...

[OK]

Switch#dir /all

Directory of flash:/

   2  -rwx         916  Mar 01 1993 00:04:09 +00:00  vlan.dat

   3  -rwx     3117090  Mar 01 1993 00:03:17 +00:00  c2950-i6q4l2-mz.121-22.EA7.bin

   4  drwx        4160  Mar 01 1993 00:03:50 +00:00  html

 375  -rwx           5  Mar 01 1993 00:26:31 +00:00  private-config.text

 376  -rwx         831  Mar 01 1993 00:26:31 +00:00  config.text

Switch#more config.text

!

enable password xunbo

重启之后

Switch>en

Password:

需要密码，现在我们假如不知道密码

1）断电重启，在启动的过程按住mode键，直到进入

The system has been interrupted prior to initializing the

flash filesystem.  The following commands will initialize

the flash filesystem, and finish loading the operating

system software:

   flash_init

   load_helper

   boot

switch:

2）

switch: flash_init

Initializing Flash...

flashfs[0]: 371 files, 4 directories

flashfs[0]: 0 orphaned files, 0 orphaned directories

flashfs[0]: Total bytes: 7741440

flashfs[0]: Bytes used: 4739072

flashfs[0]: Bytes available: 3002368

flashfs[0]: flashfs fsck took 7 seconds.

...done initializing flash.

Boot Sector Filesystem (bs:) installed, fsid: 3

Parameter Block Filesystem (pb:) installed, fsid: 4

3）switch: dir flash:

Directory of flash:/

2    -rwx  916       <date>               vlan.dat

3    -rwx  3117090   <date>               c2950-i6q4l2-mz.121-22.EA7.bin

4    drwx  4160      <date>               html

375  -rwx  5         <date>               private-config.text

376  -rwx  831       <date>               config.text

4）

switch: rename flash:config.text flash:config.old

switch: dir flash:

Directory of flash:/

2    -rwx  916       <date>               vlan.dat

3    -rwx  3117090   <date>               c2950-i6q4l2-mz.121-22.EA7.bin

4    drwx  4160      <date>               html

375  -rwx  5         <date>               private-config.text

376  -rwx  831       <date>               config.old

5）

switch: boot//重启

Switch>en

Switch#

00:01:31: %LINK-5-CHANGED: Interface Vlan1, changed state to administratively down

Switch#

Switch#

Switch#sh run

恢复出厂配置

6）

Switch#rename flash:config.old flash:config.text

Switch#copy  start run

%% Non-volatile configuration memory invalid or not present //不知道为什么行不通

Switch#copy flash:config.text system:running-config

Destination filename [running-config]?

831 bytes copied in 0.716 secs (1161 bytes/sec)

Switch#sh run

hostname Switch

!

enable password xunbo

7）接下来删掉密码

Switch#   conf t

Enter configuration commands, one per line.  End with CNTL/Z.

Switch(config)#no enable pass xunbo

Switch(config)#end

Switch#

00:09:05: %SYS-5-CONFIG_I: Configured from console by console

Switch#write

Building configuration...

[OK]

Switch#dir flash:

Directory of flash:/

   2  -rwx         916  Mar 01 1993 00:04:09 +00:00  vlan.dat

   3  -rwx     3117090  Mar 01 1993 00:03:17 +00:00  c2950-i6q4l2-mz.121-22.EA7.bin

   4  drwx        4160  Mar 01 1993 00:03:50 +00:00  html

 374  -rwx           5  Mar 01 1993 00:09:16 +00:00  private-config.text

 376  -rwx         809  Mar 01 1993 00:09:16 +00:00  config.text

大功告成！！！

记住要点：交换机与路由器的破解不一样。

交换机与寄存器无关。

破解交换机的步骤：把原来的配置改名，断电重启，按住mode键，把命名后的密码重新导入。