PingingLab传世经典系列《CCNA完全配置宝典》-4.8 Frame-Relay&RIPv2
4.8 Frame-Relay&RIPv2
实验目的：
1、掌握帧中继上部署RIPv2。
2、通过部署RIPv2实现不同分支之间的通信。
实验拓扑：
实验步骤：
1、依据图中拓扑，通过路由器模拟帧中继交换机，配置如下：
①开启帧中继交换功能
FW-SW(config)#frame-relay switching
②接口开启帧中继封装，并定义为DCE接口
FW-SW(config)#int s0/0
FW-SW(config-if)#no shutdown
FW-SW(config-if)#encapsulation frame-relay
FW-SW(config-if)#frame-relay intf-type dce
FW-SW(config-if)#exit
FW-SW(config)#int s0/1
FW-SW(config-if)#no shutdown
FW-SW(config-if)#encapsulation frame-relay
FW-SW(config-if)#frame-relay intf-type dce
FW-SW(config-if)#exit
FW-SW(config)#int s0/2
FW-SW(config-if)#no shutdown
FW-SW(config-if)#encapsulation frame-relay
FW-SW(config-if)#frame-relay intf-type dce
FW-SW(config-if)#exit
③编写帧中继转发条目
FW-SW(config)#int s0/0
FW-SW(config-if)#frame-relay route 102 interface s0/1 201
FW-SW(config-if)#frame-relay route 103 interface s0/0 301
FW-SW(config-if)#exit
FW-SW(config)#int s0/1
FW-SW(config-if)#frame-relay route 201 interface s0/0 102
FW-SW(config-if)#exit
FW-SW(config)#int s0/2
FW-SW(config-if)#frame-relay route 301 interface s0/0 103
FW-SW(config-if)#exit
2、通过部署帧中继技术，使得各个站点直连连通，其中R1为中心点，R2和R3为分支点，配置如下：
R1上
R1(config)#int s0/0
R1(config-if)#no shutdown
R1(config-if)#encapsulation frame-relay
R1(config-if)#no frame-relay inverse-arp
R1(config-if)#frame-relay map ip 192.168.1.2 102 broadcast
R1(config-if)#frame-relay map ip 192.168.1.3 103 broadcast
R1(config-if)#exit
R2上
R2(config)#int s0/0
R2(config-if)#no shutdown
R2(config-if)#encapsulation frame-relay
R2(config-if)#no frame-relay inverse-arp
R2(config-if)#frame-relay map ip 192.168.1.1 201 broadcast
R2(config-if)#frame-relay map ip 192.168.1.3 201 broadcast
R2(config-if)#exit
R3上
R3(config)#int s0/0
R3(config-if)#no shutdown
R3(config-if)#encapsulation frame-relay
R3(config-if)#no frame-relay inverse-arp
R3(config-if)#frame-relay map ip 192.168.1.1 301 broadcast
R3(config-if)#frame-relay map ip 192.168.1.2 301 broadcast
R3(config-if)#exit
测试直连连通性，如下：
R1#ping 192.168.1.2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.1.2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 36/42/60 ms
R1#ping 192.168.1.3
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.1.3, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 16/31/52 ms
R2#ping 192.168.1.3
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.1.3, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 44/68/96 ms
可以看到，直连连通没有问题。
3、部署RIPv2路由协议，使得不同分支之间能够相互通信，配置如下：
R1(config)#router rip
R1(config-router)#version 2
R1(config-router)#no auto-summary
R1(config-router)#network 1.0.0.0
R1(config-router)#network 192.168.1.0
R1(config-router)#exit
R2(config)#router rip
R2(config-router)#version 2
R2(config-router)#no auto-summary
R2(config-router)#network 2.0.0.0
R2(config-router)#network 192.168.1.0
R2(config-router)#exit
R3(config)#router rip
R3(config-router)#version 2
R3(config-router)#no auto-summary
R3(config-router)#network 3.0.0.0
R3(config-router)#network 192.168.1.0
R3(config-router)#exit
查看路由表，如下：
R1#show ip route rip
2.0.0.0/32 is subnetted, 1 subnets
R 2.2.2.2 [120/1] via 192.168.1.2, 00:00:01, Serial0/0
3.0.0.0/32 is subnetted, 1 subnets
R 3.3.3.3 [120/1] via 192.168.1.3, 00:00:17, Serial0/0
R2#show ip route rip
1.0.0.0/32 is subnetted, 1 subnets
R 1.1.1.1 [120/1] via 192.168.1.1, 00:00:15, Serial0/0
3.0.0.0/32 is subnetted, 1 subnets
R 3.3.3.3 [120/2] via 192.168.1.3, 00:00:15, Serial0/0
R3#show ip route rip
1.0.0.0/32 is subnetted, 1 subnets
R 1.1.1.1 [120/1] via 192.168.1.1, 00:00:18, Serial0/0
2.0.0.0/32 is subnetted, 1 subnets
R 2.2.2.2 [120/2] via 192.168.1.2, 00:00:18, Serial0/0
可以看到，全局路由信息已经同步，测试连通性，如下：
R1#ping 2.2.2.2 source 1.1.1.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 2.2.2.2, timeout is 2 seconds:
Packet sent with a source address of 1.1.1.1
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 16/52/80 ms
R1#ping 3.3.3.3 source 1.1.1.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 3.3.3.3, timeout is 2 seconds:
Packet sent with a source address of 1.1.1.1
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 16/25/36 ms
R2#ping 3.3.3.3 source 2.2.2.2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 3.3.3.3, timeout is 2 seconds:
Packet sent with a source address of 2.2.2.2
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 24/52/84 ms
测试成功，说明在帧中继上部署RIPv2可以实现不同分支互联。但是需要提醒一点，默认情况下，运行RIPv2时，接口下关闭水平分割，如下：
R1#show ip interface s0/0
Serial0/0 is up, line protocol is up
Internet address is 192.168.1.1/24
Broadcast address is 255.255.255.255
Address determined by non-volatile memory
MTU is 1500 bytes
Helper address is not set
Directed broadcast forwarding is disabled
Multicast reserved groups joined: 224.0.0.9
Outgoing access list is not set
Inbound access list is not set
Proxy ARP is enabled
Local Proxy ARP is disabled
Security level is default
Split horizon is disabled
……
若水平分割开启，则分支之间的路由信息学习会出现问题，在之后的实验中有解答。此实验完成。
==========================================
PingingLab・高品质IT教育提供商
CCIE 实验室・IT项目实战・高端人才定制
深圳拼客信息科技有限公司・广州大学城外环西路站
新浪微博：@拼客科技PingingLab @PingingLab-陈鑫杰
PingingLab微信公众号：pinginglab
PingingLab技术交流群：240920680
