思科路由器命令大全(一)

router>         用户模式
1 :进入特权模式  enable
router > enable
router #
 
2 :进入全局配置模式  configure terminal
router > enable
router c onfigure terminal
router (conf)#
 
3 :交换机命名 hostname routera    routerA为例
router > enable
router c onfigure terminal
router(conf)#hostname routerA
routera (conf)#
 
4 :配置使能口令  enable password cisco    cisco为例
router > enable
router c onfigure terminal
router(conf)#hostname routerA
routerA (conf)# enable password cisco
 
5 :配置使能密码  enable secret ciscolab    cicsolab为例
router > enable
router c onfigure terminal
router(conf)#hostname routerA
routerA (conf)# enable secret ciscolab
 
6 :进入路由器某一端口 interface fastehernet 0/17           17端口为例
router > enable
router c onfigure terminal
router(conf)#hostname routerA
routerA (conf)# interface fastehernet 0/17
routerA (conf-if)#
进入路由器的某一子端口 interface fastethernet 0/17.1       17端口的1子端口为例
router > enable
router c onfigure terminal
router(conf)#hostname routerA
routerA (conf)# interface fastehernet 0/17.1
 
7 :设置端口ip地址信息
router > enable
router c onfigure terminal
本文出自 51CTO.COM技术博客 router(conf)#hostname routerA
routerA(conf)# interface fastehernet  0/17               17端口为例
routerA (conf-if)#ip address 192.168.1.1 255.255.255.0      配置交换机端口ip和子网掩码
routerA (conf-if)#no shut                            配置处于运行中
routerA (conf-if)#exit
 
8 :查看命令  show
router > enable
router # show version  察看系统中的所有版本信息
show interface vlan 1  查看交换机有关ip协议的配置信息
show running-configure 查看交换机当前起作用的配置信息
show interface fastethernet 0/1  察看交换机1接口具体配置和统计信息
show mac-address-table        查看mac地址表
show mac-address-table aging-time  查看mac地址表自动老化时间
show controllers serial + 编号    查看串口类型
show ip router      查看路由器的路由表
 
9 cdp相关命令
router > enable
router # show cdp    查看设备的cdp全局配置信息
show cdp interface fastethernet 0/17    查看17端口的cdp配置信息
show cdp traffic     查看有关cdp包的统计信息
show cdp nerghbors  列出与设备相连的cisco设备
 
10 csico2600的密码恢复
重新启动路由器,在启动过程中按下win+break键,使路由器进入rom monitor
在提示符下输入命令修改配置寄存器的值,然后重新启动路由器
remmon1>confreg 0x2142
remmon2>reset
重新启动路由器后进入setup模式,选择“no”,退回到exec模式,此时路由器原有的配置仍然保存在startup-config中,为使路由器恢复密码后配置不变把startup-config中配置保存到running-config中,然后重新设置enable密码,并把配置寄存器改回0x2102
router>enable
router#copy startup-config running-config
router c onfigure terminal
router(conf)#enable password cisco
router(conf) c onfig-register 0x2102
保存当前配置到startup-config ,重新启动路由器。
router #copy running-config startup-config
router #reload

你可能感兴趣的:(职场,休闲)