在CISCO路由器上实现CHAP认证

  在配置PPP验证时有PAP和CHAP的选择，其中PAP为明文传送用户名和口令，不安全；而CHAP则采用哈希值进行验证，口令不会在网上传送，所以安全性比较高。

         网络拓扑图如下所示：

         说明：PC1的以太口（192.168.10.2）与Router1的以太网接口（192.168.10.1）相连；Router1的Serial 0/0（10.10.10.1）与Router2的Serial 0/0（10.10.10.2）相连，Router1为DCE，Router2为DTE；Router2的以太网接口（192.168.20.1）与PC2的以太口（192.168.20.2）相连。路由协议采用静态路由，路由器为模拟的Cisco3640.

 

一、Router1的配置如下：
Router>enable
Router#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#hostname Router1
Router1(config)#interface ethernet 0/0
Router1(config-if)#ip address 192.168.10.1 255.255.255.0
Router1(config-if)#no shutdown
%LINK-3-UPDOWN: Interface Ethernet0/0, changed state to up
Router1(config-if)#exit
Router1(config)#interface serial 0/0
Router1(config-if)#ip address 10.10.10.1 255.255.255.0
Router1(config-if)#clock rate 64000
Router1(config-if)#no shutdown
%LINK-3-UPDOWN: Interface Serial0/0, changed state to up
%LINK-3-UPDOWN: Interface Serial0/0, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed state to down
Router1(config-if)#exit
%LINK-3-UPDOWN: Interface Serial0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed state to up

Router1(config)#ip route 192.168.20.0 255.255.255.0 10.10.10.2

Router1(config)#username Router2 password cisco
Router1(config)#interface serial 0/0
Router1(config-if)#encapsulation ppp
%LINK-3-UPDOWN: Interface Serial0/0, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed state to down
Router1(config-if)#ppp authentication chap
Router1(config-if)#exit

Router1(config)#exit
Router1#copy running-config startup-config
Destination filename [startup-config]?
Building configuration...
[OK]

%LINK-3-UPDOWN: Interface Serial0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed state to up

 

================================================================

 

二、Router2的配置如下：

Router>enable
Router#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#hostname Router2
Router2(config)#interface ethernet 0/0
Router2(config-if)#ip address 192.168.20.1 255.255.255.0
Router2(config-if)#no shutdown
%LINK-3-UPDOWN: Interface Ethernet0/0, changed state to up
Router2(config-if)#exit
Router2(config)#interface serial 0/0
Router2(config-if)#ip address 10.10.10.2 255.255.255.0

Router2(config-if)#no shutdown
%LINK-3-UPDOWN: Interface Serial0/0, changed state to up
Router2(config-if)#exit

Router2(config)#ip route 192.168.10.0 255.255.255.0 10.10.10.1

%LINK-3-UPDOWN: Interface Serial0/0, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed state to down
Router2(config)#username Router1 password cisco
Router2(config)#interface serial 0/0
Router2(config-if)#encapsulation ppp
Router2(config-if)#ppp authentication chap
%LINK-3-UPDOWN: Interface Serial0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed state to up
Router2(config-if)#exit
Router2(config)#exit
Router2#copy running-config startup-config
Destination filename [startup-config]?
Building configuration...
[OK]

 

==================================================================

 

三、测试网络的连通性：

 

PC1和PC2的IP配置
VPCS 1 >ip 192.168.10.2 192.168.10.1
VPCS 2 >ip 192.168.20.2 192.168.20.1

 

1、在PC1上pingPC2=》 C:>ping 192.168.20.2

2、在PC2上pingPC1=》 C:>ping 192.168.10.2

 

====================================================================

 

四、查看Serial 0/0的相关信息：

1、Router1#show interfaces serial 0/0
Serial0/0 is up, line protocol is up    ------接口与协议均已开启
  Hardware is HD64570
  Internet address is 10.10.10.1/24

  MTU 1500 bytes, BW 1544 Kbit, DLY 1000 usec, rely 255/255, load 1/255
  Encapsulation PPP, loopback not set, keepalive set (10 sec)
  LCP Open       -----开启
  Open: IPCP, CDPCP      ------开启
  Last input 00:00:00, output 00:00:00, output hang never
  Last clearing of show interface counters never
  Queueing strategy: fifo
 

2、Router2#show interfaces serial 0/0
Serial0/0 is up, line protocol is up  -----接口与协议均已开启
  Hardware is HD64570
  Internet address is 10.10.10.2/24

  MTU 1500 bytes, BW 1544 Kbit, DLY 1000 usec, rely 255/255, load 1/255
  Encapsulation PPP, loopback not set, keepalive set (10 sec)
  LCP Open           -------开启
  Open: IPCP, CDPCP     -------开启
  Last input 00:00:00, output 00:00:00, output hang never
  Last clearing of show interface counters never
  Queueing strategy: fifo
 

09年11月8日修改