RIP和EIGRP之间的重分发

首先把三台路由器的IP地址都配上！
Router1>en
Router1#conf t
Router1(config)#int s0/0
Router1(config-if)#ip address 10.1.1.1 255.255.255.0
Router1(config-if)#clock rate 64000
Router1(config-if)#no shut
Router1(config-if)#exit
Router1(config)#int f0/0
Router1(config-if)#ip address 1.1.1.1 255.255.255.0
Router1(config-if)#no shut
Router1(config)#int f1/0
Router1(config-if)#ip address 2.2.2.2 255.255.255.0
Router1(config-if)#no shut
Router1(config)#int f1/1
Router1(config-if)#ip address 3.3.3.3 255.255.255.0
Router1(config-if)#no shut

Router2>en
Router2#conf t
Router2(config)#int s0/0
Router2(config-if)#ip ad
Router2(config-if)#ip address 10.1.1.2 255.255.255.0
Router2(config-if)#no shut
Router2(config-if)#exit
Router2(config)#int s0/1
Router2(config-if)#ip address 11.1.1.1 255.255.255.0
Router2(config-if)#no shut
Router2(config-if)#exit

Router3>en
Router3#conf t
Router3(config)#int s0/0
Router3(config-if)#ip address 11.1.1.2 255.255.255.0
Router3(config-if)#clock rate 64000
Router3(config-if)#no shut
Router3(config-if)#exit
Router3(config)#int f0/0
Router3(config-if)#ip address 4.4.4.4 255.255.255.0
Router3(config-if)#no shut
Router3(config)#int f1/0
Router3(config-if)#ip address 5.5.5.5 255.255.255.0
Router3(config-if)#no shut
Router3(config)#int f1/1
Router3(config-if)#ip address 6.6.6.6 255.255.255.0
Router3(config-if)#no shut

IP都定义好了！
下步起路由协议了

Router1(config)#router rip
Router1(config-router)#network 1.1.1.0
Router1(config-router)#network 2.2.2.0
Router1(config-router)#network 3.3.3.0
Router1(config-router)#network 10.1.1.0
Router1(config-router)#

Router3(config)#router eigrp 90
Router3(config-router)#network 4.4.4.0
Router3(config-router)#network 5.5.5.0
Router3(config-router)#network 6.6.6.0
Router3(config-router)#network 11.1.1.0
Router3(config-router)#

Router2(config)#router rip
Router2(config-router)#network 10.1.1.0
Router2(config-router)#network 11.1.1.0
Router2(config-router)#exit
Router2(config)#router eigrp 90
Router2(config-router)#network 10.1.1.0
Router2(config-router)#network 11.1.1.0
Router2(config-router)#exit

路由协议都起来了，现在要配置
如何将RIP发布到EIGRP中
如何将EIGRP发布到RIP中
如果不做这步骤的话，6台PC不能实现连通！

Router2(config)#router rip
Router2(config-router)#redistribute eigrp 90 metric 1
Router2(config-router)#exit
Router2(config)#router eigrp 90
Router2(config-router)#redistribute rip metric 100000 10 255 1 1500
Router2(config-router)#exit

OK这样6台PC也就可以通信了！