NA-NP-IE系列实验11：RIPv1 基本配置
实验11：RIPv1 基本配置
1.
实验目的
通过本实验可以掌握：
（1）在路由器上启动RIPv1 路由进程
（2）启用参与路由协议的接口，并且通告网络
（3）理解路由表的含义
（4）查看和调试RIPv1 路由协议相关信息
2.
拓扑结构
实验拓扑如图 所示。
3.
实验步骤
1
）步骤1：配置路由器R0
Router>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#ho r0
r0(config)#no ip domain-loo
r0(config)#lin c 0
r0(config-line)#logg s
r0(config-line)#exit
r0(config)#lin c 0
r0(config-line)#exec-t 00
r0(config-line)#exit
r0(config)#int s 1/1/0
r0(config-if)#ip add 192.168.12.1 255.255.255.0
r0(config-if)#no sh
%LINK-5-CHANGED: Interface Serial 1/1/0 , changed state to down
r0(config-if)#exit
r0(config)#int loo 1
%LINK-5-CHANGED: Interface Loopback1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Loopback1, changed state to up
r0(config-if)#ip add 1.1.1 .1 255.255.255.0
%LINK-5-CHANGED: Interface Serial 1/1/0 , changed state to up
%SYS-5-CONFIG_I: Configured from console by console
r0#sh ip int b
Interface IP-Address OK? Method Status Protocol
FastEthernet0/0 unassigned YES manual administratively down down
FastEthernet0/1 unassigned YES manual administratively down down
FastEthernet1/0 unassigned YES manual administratively down down
Serial 1/1/0 192.168.12.1 YES manual up down
Serial 1/1/1 unassigned YES manual administratively down down
Loopback1 1.1.1 .1 YES manual up up
Vlan1 unassigned YES manual administratively down down
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial 1/1/0 , changed state to up
r0#sh ip int b
Interface IP-Address OK? Method Status Protocol
FastEthernet0/0 unassigned YES manual administratively down down
FastEthernet0/1 unassigned YES manual administratively down down
FastEthernet1/0 unassigned YES manual administratively down down
Serial 1/1/0 192.168.12.1 YES manual up up
Serial 1/1/1 unassigned YES manual administratively down down
Loopback1 1.1.1 .1 YES manual up up
Vlan1 unassigned YES manual administratively down down
r0#conf t
Enter configuration commands, one per line. End with CNTL/Z.
r0(config)#router rip
//
启动RIP 进程
r0(config-router)#ver 1//配置RIP 版本1
r0(config-router)#net 1.1.1 .0//通告网络
r0(config-router)#net 192.168.12.0
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.34.2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 93/93/94 ms
r0(config-router)#do ping 4.4.4 .4
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 4.4.4 .4, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 78/90/94 ms
r0(config-router)#do sh ip route //该命令用来查看路由表。
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF , IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
* - candidate default, U - per-user static route, o - ODR
P - periodic downloaded static route
Gateway of last resort is not set
1.0.0 .0/24 is subnetted, 1 subnets
C 1.1.1 .0 is directly connected, Loopback1
R 4.0.0 .0/8 [120/3] via 192.168.12.2, 00:00:26, Serial 1/1/0
C 192.168.12.0/24 is directly connected, Serial 1/1/0
R 192.168.23.0/24 [120/1] via 192.168.12.2, 00:00:26, Serial 1/1/0
R 192.168.34.0/24 [120/2] via 192.168.12.2, 00:00:26, Serial 1/1/0
以上输出表明路由器R1 学到了3 条RIP 路由，其中路由条目“R 4.0.0 .0/8 [120/3]
via 192.168.12.2, 00:00:26, Serial1/1/0
”的含义如下：
① R：路由条目是通过RIP 路由协议学习来的；
② 4.0.0 .0/8：目的网络；
③ 120：RIP 路由协议的默认管理距离；
④ 3: 度量值，从路由器R1 到达网络 4.0.0 .0/8 的度量值为3 跳；
⑤ 192.168.12.2：下一跳地址；
⑥ 00:00:26：距离下一次更新还有4（30-26）秒；
⑦ Serial1/1/0：接收该路由条目的本路由器的接口。
同时通过该路由条目的掩码长度可以看到，RIPv1 确实不传递子网信息。
2
）步骤2：配置路由器R1
Router>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#ho r1
r1(config)#no ip domain-loo
r1(config)#lin c 0
r1(config-line)#logg s
r1(config-line)#exec-t 00
r1(config-line)#exit
r1(config)#int s 1/1/0
r1(config-if)#ip add 192.168.12.2 255.255.255.0
r1(config-if)#no sh
%LINK-5-CHANGED: Interface Serial 1/1/0 , changed state to up
r1(config-if)#exit
r1(config)#int s 1/1/1
r1(config-if)#ip add 192.168.23.1 255.255.255.0
r1(config-if)#no sh
%LINK-5-CHANGED: Interface Serial 1/1/1 , changed state to up
r1(config-if)#end
%SYS-5-CONFIG_I: Configured from console by console
r1#ping 192.168.23.2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.23.2, timeout is 2 seconds:
.....
Success rate is 0 percent (0/5)
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial 1/1/1 , changed state to up
r1#conf t
Enter configuration commands, one per line. End with CNTL/Z.
r1(config)#int s 1/1/0
r1(config-if)#clo r 64000
r1(config-if)#no sh
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial 1/1/0 , changed state to up
r1(config-if)#exit
r1(config)#router rip
r1(config-router)#ver 1
r1(config-router)#net 192.168.23.0
r1(config-router)#net 192.168.12.0
3
）步骤3：配置路由器R2
Router>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#ho r2
r2(config)#no ip domain-loo
r2(config)#lin c 0
r2(config-line)#logg s
r2(config-line)#exec-t 00
r2(config-line)#exit
r2(config)#int s 1/1/1
r2(config-if)#ip add 192.168.23.2 255.255.255.0
r2(config-if)#no sh
%LINK-5-CHANGED: Interface Serial 1/1/1 , changed state to down
r2(config-if)#int s 1/1/0
r2(config-if)#ip add 192.168.34.1 255.255.255.0
r2(config-if)#no sh
%LINK-5-CHANGED: Interface Serial 1/1/0 , changed state to down
r2(config-if)#
%LINK-5-CHANGED: Interface Serial 1/1/0 , changed state to up
r2(config-if)#
%LINK-5-CHANGED: Interface Serial 1/1/1 , changed state to up
r2(config-if)#^Z
%SYS-5-CONFIG_I: Configured from console by console
r2#sh ip int b
Interface IP-Address OK? Method Status Protocol
FastEthernet0/0 unassigned YES manual administratively down down
FastEthernet0/1 unassigned YES manual administratively down down
FastEthernet1/0 unassigned YES manual administratively down down
FastEthernet1/1 unassigned YES manual administratively down down
Serial 1/1/0 192.168.34.1 YES manual up down
Serial 1/1/1 192.168.23.2 YES manual up down
Vlan1 unassigned YES manual administratively down down
r2#conf t
Enter configuration commands, one per line. End with CNTL/Z.
r2(config)#int s 1/1/1
r2(config-if)#clo r 64000
r2(config-if)#no sh
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial 1/1/1 , changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial 1/1/0 , changed state to up
r2(config-if)#exit
r2(config)#router rip
r2(config-router)#ver 1
r2(config-router)#net 192.168.34.0
r2(config-router)#net 192.168.23.0
4
）步骤4：配置路由器R3
Router>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#ho r3
r3(config)#no ip domain-loo
r3(config)#lin c 0
r3(config-line)#logg s
r3(config-line)#exec-t 00
r3(config-line)#exit
r3(config)#int loo 1
%LINK-5-CHANGED: Interface Loopback1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Loopback1, changed state to up
r3(config-if)#ip add 4.4.4 .4 255.255.255.0
r3(config-if)#no sh
r3(config-if)#int s 1/1/0
r3(config-if)#ip add 192.168.34.2 255.255.255.0
r3(config-if)#no sh
%LINK-5-CHANGED: Interface Serial 1/1/0 , changed state to up
%SYS-5-CONFIG_I: Configured from console by console
r3#sh ip int b
Interface IP-Address OK? Method Status Protocol
FastEthernet0/0 unassigned YES manual administratively down down
FastEthernet0/1 unassigned YES manual administratively down down
FastEthernet1/0 unassigned YES manual administratively down down
Serial 1/1/0 192.168.34.2 YES manual up down
Serial 1/1/1 unassigned YES manual administratively down down
Loopback1 4.4.4 .4 YES manual up up
Vlan1 unassigned YES manual administratively down down
r3#conf t
Enter configuration commands, one per line. End with CNTL/Z.
r3(config)#int s 1/1/0
r3(config-if)#clo r 64000
r3(config-if)#no sh
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial 1/1/0 , changed state to up
r3(config-if)#^Z
%SYS-5-CONFIG_I: Configured from console by console
r3#sh ip int b
Interface IP-Address OK? Method Status Protocol
FastEthernet0/0 unassigned YES manual administratively down down
FastEthernet0/1 unassigned YES manual administratively down down
FastEthernet1/0 unassigned YES manual administratively down down
Serial 1/1/0 192.168.34.2 YES manual up up
Serial 1/1/1 unassigned YES manual administratively down down
Loopback1 4.4.4 .4 YES manual up up
Vlan1 unassigned YES manual administratively down down
r3#ping 192.168.34.2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.34.2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 47/59/62 ms
r3#conf t
Enter configuration commands, one per line. End with CNTL/Z.
r3(config)#router rip
r3(config-router)#ver 1
r3(config-router)#net 192.168.34.0
r3(config-router)#net 4.4.4 .0
r3(config-router)#exit
r3(config)#exit
%SYS-5-CONFIG_I: Configured from console by console
r3#ping 1.1.1 .1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 1.1.1 .1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 78/90/94 ms
r3#sh ip route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF , IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
* - candidate default, U - per-user static route, o - ODR
P - periodic downloaded static route
Gateway of last resort is not set
R 1.0.0 .0/8 [120/3] via 192.168.34.1, 00:00:02, Serial 1/1/0
4.0.0 .0/24 is subnetted, 1 subnets
C 4.4.4 .0 is directly connected, Loopback1
R 192.168.12.0/24 [120/2] via 192.168.34.1, 00:00:02, Serial 1/1/0
R 192.168.23.0/24 [120/1] via 192.168.34.1, 00:00:02, Serial 1/1/0
C 192.168.34.0/24 is directly connected, Serial 1/1/0
本文出自 “柯浩坚” 博客，转载请与作者联系！