AIX安装CRS错误

 AIX安装CRS错误

系统环境:

    OS:IBM  AIX 5.3.8   +   HACMP 5.2

    DATABASE: Oracle 10g  +   Oracle   CRS

 

在做AIX 下的RAC 时,安装CRS时,在其中一个节点上出像如下错误:

[root@aix192 /]# /u01/crs/root.sh

WARNING: directory '/u01' is not owned by root

Checking to see if Oracle CRS stack is already configured

Checking to see if any 9i GSD is up

 

cp: /dev/rocrdisk: Read-only file system

1

[root@aix192 /]# lsvg

rootvg

racvg

[root@aix192 /]# lsvg racvg

VOLUME GROUP:       racvg                    VG IDENTIFIER:  0008d56c00004c0000000135c5df1180

VG STATE:           active                   PP SIZE:        64 megabyte(s)

VG PERMISSION:      passive-only             TOTAL PPs:      1600 (102400 megabytes)

MAX LVs:            256                      FREE PPs:       1519 (97216 megabytes)

LVs:                20                       USED PPs:       81 (5184 megabytes)

OPEN LVs:           0                        QUORUM:         2 (Enabled)

TOTAL PVs:          1                        VG DESCRIPTORS: 2

STALE PVs:          0                        STALE PPs:      0

ACTIVE PVs:         1                        AUTO ON:        no

Concurrent:         Enhanced-Capable         Auto-Concurrent: Disabled

VG Mode:            Concurrent                              

Node ID:        3                        Active Nodes:   2

MAX PPs per VG:     32512                                    

MAX PPs per PV:     2032                     MAX PVs:        16

LTG size (Dynamic): 256 kilobyte(s)          AUTO SYNC:      no

HOT SPARE:          no                       BB POLICY:      relocatable

[root@aix192 /]# lspv

hdisk0          000c41bfd887a4f9                    rootvg          active

hdisk1          0008d56cc5df108f                    racvg           concurrent

hdisk2          none                                None           

[root@aix192 /]# lslv ocrdisk

LOGICAL VOLUME:     ocrdisk                VOLUME GROUP:   racvg

LV IDENTIFIER:      0008d56c00004c0000000135c5df1180.2 PERMISSION:     read/write

VG STATE:           active/complete        LV STATE:       closed/syncd

TYPE:               jfs                    WRITE VERIFY:   off

MAX LPs:            512                    PP SIZE:        64 megabyte(s)

COPIES:             1                      SCHED POLICY:   parallel

LPs:                2                      PPs:            2

STALE PPs:          0                      BB POLICY:      relocatable

INTER-POLICY:       minimum                RELOCATABLE:    yes

INTRA-POLICY:       middle                 UPPER BOUND:    16

MOUNT POINT:        N/A                    LABEL:          None

MIRROR WRITE CONSISTENCY: on/ACTIVE                             

EACH LP COPY ON A SEPARATE PV ?: yes                                   

Serialize IO ?:     NO             

                      

[root@aix192 /]# chlv -p w ocrdisk

0516-1318 chlv: The volume group is currently in read-only mode.

        Use varyoffvg, then varyonvg in read-write mode before trying this command again.

0516-704 chlv: Unable to change logical volume ocrdisk.

 

解决方法:

 

[root@aix192 /]# varyoffvg racvg

[root@aix192 /]# varyonvg racvg

[root@aix192 /]# chlv -p w ocrdisk

[root@aix192 /]# lslv ocrdisk

LOGICAL VOLUME:     ocrdisk                VOLUME GROUP:   racvg

LV IDENTIFIER:      0008d56c00004c0000000135c5df1180.2 PERMISSION:     read/write

VG STATE:           active/complete        LV STATE:       closed/syncd

TYPE:               jfs                    WRITE VERIFY:   off

MAX LPs:            512                    PP SIZE:        64 megabyte(s)

COPIES:             1                      SCHED POLICY:   parallel

LPs:                2                      PPs:            2

STALE PPs:          0                      BB POLICY:      relocatable

INTER-POLICY:       minimum                RELOCATABLE:    yes

INTRA-POLICY:       middle                 UPPER BOUND:    16

MOUNT POINT:        N/A                    LABEL:          None

MIRROR WRITE CONSISTENCY: on/ACTIVE                             

EACH LP COPY ON A SEPARATE PV ?: yes                                   

Serialize IO ?:     NO                                    

[root@aix192 /]# /u01/crs/root.sh

WARNING: directory '/u01' is not owned by root

Checking to see if Oracle CRS stack is already configured

Checking to see if any 9i GSD is up

 

Setting the permissions on OCR backup directory

Setting up NS directories

Oracle Cluster Registry configuration upgraded successfully

WARNING: directory '/u01' is not owned by root

clscfg: EXISTING configuration version 3 detected.

clscfg: version 3 is 10G Release 2.

Successfully accumulated necessary OCR keys.

Using ports: CSS=49895 CRS=49896 EVMC=49898 and EVMR=49897.

node <nodenumber>: <nodename> <private interconnect name> <hostname>

node 2: aix191 aix191-priv aix191

node 3: aix192 aix192-priv aix192

clscfg: Arguments check out successfully.

 

NO KEYS WERE WRITTEN. Supply -force parameter to override.

-force is destructive and will destroy any previous cluster

configuration.

Oracle Cluster Registry for cluster has already been initialized

Startup will be queued to init within 30 seconds.

Adding daemons to inittab

Adding daemons to inittab

Expecting the CRS daemons to be up within 600 seconds.

CSS is active on these nodes.

        aix191

        aix192

CSS is active on all nodes.

Waiting for the Oracle CRSD and EVMD to start

Waiting for the Oracle CRSD and EVMD to start

Waiting for the Oracle CRSD and EVMD to start

Oracle CRS stack installed and running under init(1M)

Running vipca(silent) for configuring nodeapps

The given interface(s), "en0" is not public. Public interfaces should be used to configure virtual IPs.

[root@aix192 /]#

本文出自 “天涯客的blog” 博客,请务必保留此出处http://tiany.blog.51cto.com/513694/794175

你可能感兴趣的:(AIX安装CRS错误)