Protocol Commands

NewCommands  

Make Me a Sandwich

Updated Jul 14, 2012 by [email protected]

    Memcached handles a small number of basic commands.

    Full documentation can be found in the Protocol Documentation.

    Standard Protocol

    The "standard protocol stuff" of memcached involves running a command against an "item". An item consists of:

    • A key (arbitrary string up to 250 bytes in length. No space or newlines for ASCII mode)

    • A 32bit "flag" value

    • An expiration time, in seconds. Can be up to 30 days. After 30 days, is treated as a unix timestamp of an exact date.

    • A 64bit "CAS" value, which is kept unique.

    • Arbitrary data

    CAS is optional (can be disabled entirely with -C, and there are more fields that internally make up an item, but these are what your client interacts with.

    No Reply

    Most ASCII commands allow a "noreply" version. One should not normally use this with the ASCII protocol, as it is impossible to align errors with requests. The intent is to avoid having to wait for a return packet after executing a mutation command (such as a set or add).

    The binary protocol properly implements noreply (quiet) statements. If you have a client which supports or uses the binary protocol, odds are good you may take advantage of this.

    Storage Commands

    set

    Most common command. Store this data, possibly overwriting any existing data. New items are at the top of the LRU.

    add

    Store this data, only if it does not already exist. New items are at the top of the LRU. If an item already exists and an add fails, it promotes the item to the front of the LRU anyway.

    replace

    Store this data, but only if the data already exists. Almost never used, and exists for protocol completeness (set, add, replace, etc)

    append

    Add this data after the last byte in an existing item. This does not allow you to extend past the item limit. Useful for managing lists.

    prepend

    Same as append, but adding new data before existing data.

    cas

    Check And Set (or Compare And Swap). An operation that stores data, but only if no one else has updated the data since you read it last. Useful for resolving race conditions on updating cache data.

    Retrieval Commands

    get

    Command for retrieving data. Takes one or more keys and returns all found items.

    gets

    An alternative get command for using with CAS. Returns a CAS identifier (a unique 64bit number) with the item. Return this value with the cascommand. If the item's CAS value has changed since you gets'ed it, it will not be stored.

    delete

    Removes an item from the cache, if it exists.

    incr/decr

    Increment and Decrement. If an item stored is the string representation of a 64bit integer, you may run incr or decr commands to modify that number. You may only incr by positive values, or decr by positive values. They does not accept negative values.

    If a value does not already exist, incr/decr will fail.

    Statistics

    There're a handful of commands that return counters and settings of the memcached server. These can be inspected via a large array of tools or simply by telnet or netcat. These are further explained in the protocol docs.

    stats

    ye 'ole basic stats command.

    stats items

    Returns some information, broken down by slab, about items stored in memcached.

    stats slabs

    Returns more information, broken down by slab, about items stored in memcached. More centered to performance of a slab rather than counts of particular items.

    stats sizes

    A special command that shows you how items would be distributed if slabs were broken into 32byte buckets instead of your current number of slabs. Useful for determining how efficient your slab sizing is.

    WARNING this is a development command. As of 1.4 it is still the only command which will lock your memcached instance for some time. If you have many millions of stored items, it can become unresponsive for several minutes. Run this at your own risk. It is roadmapped to either make this feature optional or at least speed it up.

    flush_all

    Invalidate all existing cache items. Optionally takes a parameter, which means to invalidate all items after N seconds have passed.

    This command does not pause the server, as it returns immediately. It does not free up or flush memory at all, it just causes all items to expire.


    你可能感兴趣的:(Protocol Commands)