How to setup an iSCSI target using tgtadm

<<How to setup an iSCSI target using tgtadm>>

1.Start the tgtd service
#service tgtd start
The tgtd service is provided by the package: scsi-target-utils.x86_64

2.Define an iSCSI target name: (for example)
# tgtadm --lld iscsi --op new --mode target --tid=1 --targetname iqn.2001-04.com.example:storage.disk1.amiens.sys1.xyz

3.To view the currect configuration:
# tgtadm --lld iscsi --op show --mode target

For example, here we create a 10G file as the block device:
# dd if=/dev/zero of=/disk1 bs=1M count=10240

4.Add it as a logical unit to the target:
# tgtadm --lld iscsi --op new --mode logicalunit --tid 1 --lun 1 -b /disk1

5.Enable the target to accept any initiators:
# tgtadm --lld iscsi --op bind --mode target --tid 1 -I ALL

6.View the current configuration again:
# tgtadm --lld iscsi --op show --mode target
Target 1: iqn.2001-04.com.example:storage.disk1.amiens.sys1.xyz
    System information:
        Driver: iscsi
        Status: running
    I_T nexus information:
    LUN information:
        LUN: 0
            Type: controller
            SCSI ID: deadbeaf1:0
            SCSI SN: beaf10
            Size: 0
            Backing store: No backing store
        LUN: 1
            Type: disk
            SCSI ID: deadbeaf1:1
            SCSI SN: beaf11
            Size: 55G
            Backing store: /disk1
    Account information:
    ACL information:
        ALL

7.Ensure TCP port 3260 can be accessed from remote host.

8.Start from Red Hat Enterprise Linux 5.3, tgt-admin and /etc/tgt/targets.conf can be used for make the setup persistent over reboot:
# tgt-admin --dump > /etc/tgt/targets.conf
# chkconfig tgtd on

9.In releases prior to Red Hat Enterprise Linux 5.3, you have to put the "tgtadm" commands into /etc/rc.local and enable the tgtd service:

echo >> /etc/rc.local <<EOF
tgtadm --lld iscsi --op new --mode target --tid=1 --targetname iqn.2001-04.com.example:storage.disk1.amiens.sys1.xyz
tgtadm --lld iscsi --op new --mode logicalunit --tid 1 --lun 1 -b /disk1
tgtadm --lld iscsi --op bind --mode target --tid 1 -I ALL
EOF

# chkconfig tgtd on


<<How to configure the iscsi-initiator>>

1.First install the iscsi-initiator-utils package

#yum install iscsi-initiator-utils

2.Second start the iscsid service and enable it to start when the system boots:

#service iscsid start
#chkconfig iscsid on

3.Then obtain a listing of available targets from a given host (please note that ipaddress listed below must be replaced with the resolvable hostname or ip address of the system providing the port if different than default):

#iscsiadm -m discovery -t sendtargets -p ipaddress

4.Finally, use the following command to login to the available target (again, replace targetname with one from the output of the previous command and replace ipaddress below with that of the target system):

#iscsiadm -m node -T targetname -p ipaddress -l

 

This will enable the target to be accessed upon reboots and it stores it in a node database found in /var/lib/iscsi that is more thoroughly described in the /usr/share/doc/iscsi-initiator-utils-VERSION/README file.

For a more verbose listing of possible options for the iscsiadm command in Red Hat Enterprise Linux 5 refer to the manual page using:

#man iscsiadm













你可能感兴趣的:(How to setup an iSCSI target using tgtadm)