APC UPS 如何用计算机串口超级终端配置AP9617/AP9618/AP9619

使用AP9617,AP9618,AP9619之前，必须设置一些基本参数。本文介绍了如何通过串口通讯方式配置AP9617，AP9618,AP9619. 配置步骤如下： 1．使用940-0024C通讯线（网络管理卡附带）连接运行终端仿真程序的计算机和UPS。 2．如该计算机的串口（连接940-0024C通讯线）正被APC软件PowerChute Plus或其他程序使用，请关闭相关程序。 启动终端仿真程序如HyperTerminal，设置串口参数为：2400bps, No Parity , 8 data bits , 1 stop bit , and No Flow Control 注：修改串口参数后，要断开并重新连接该会话(connection)之后，设置方生效。 3.      确认上述两步无误后，按回车键。 4.      输入 User Name及 Password ，其缺省设置均为 apc。 5.      正确登录后，网络管理卡的管理界面将自动弹出。 显示界面如下：（请根据您的需求修改相关参数） User Name : apc Password   : *** American Power Conversion                Network Management Card AOS       v2.1.1 (c) Copyright 2002 All Rights Reserved   Smart-UPS & Matrix-UPS APP        v2.1.0 ------------------------------------------------------------------------------- Name       : Unknown                                    Date : 12/11/2003 Contact    : Unknown                                    Time : 11:47:50 Location   : Unknown                                    User : Administrator Up Time    : 0 Days 0 Hours 20 Minutes                  Stat : P+ N? A+ Environment : Threshold Violation Present, Contact Alarms Disabled, Relay      Disabled Smart-UPS 1000 named   : On Line ------- Control Console -------------------------------------------------------       1- Device Manager       2- Network       3- System       4- Logout       - Main Menu, - Refresh, - Event Log > 2 ------- Network ---------------------------------------------------------------       1- TCP/IP       2- DNS       3- Ping Utility       4- FTP Server       5- Telnet/SSH       6- Web/SSL/TLS       7- WAP       8- SNMP       9- Email      10- Syslog       - Back, - Refresh, - Event Log > 1 ------- TCP/IP ----------------------------------------------------------------          Network not started. Currently making a BOOTP request...          -----------------------------------------------------------------------          MAC Address : 00 C0 B7 67 37 4C       1- Boot Mode   : DHCP & BOOTP       2- Advanced...       - Back, - Refresh, - Event Log > 1 ------- Boot Mode -------------------------------------------------------------       1- DHCP & BOOTP       2- DHCP only       3- BOOTP only       4- Manual       - Back, - Refresh > 4 ------- TCP/IP ----------------------------------------------------------------          Network not started. Currently making a BOOTP request...          -----------------------------------------------------------------------          MAC Address : 00 C0 B7 67 37 4C          * Changes will take effect on Logout.       1- System IP       : 159.215.125.248       2- Subnet Mask     : 255.255.255.0       3- Default Gateway: 159.215.125.1       4- Boot Mode       : Manual       5- Advanced...       - Back, - Refresh, - Event Log > 1 System IP : 159.215.125.248 ------- TCP/IP ----------------------------------------------------------------          Network not started. Currently making a BOOTP request...          -----------------------------------------------------------------------          MAC Address : 00 C0 B7 67 37 4C          * Changes will take effect on Logout.       1- System IP       : 159.215.125.248       2- Subnet Mask     : 255.255.255.0       3- Default Gateway: 159.215.125.1       4- Boot Mode       : Manual       5- Advanced...       - Back, - Refresh, - Event Log > 5 ------- Advanced... -----------------------------------------------------------          Link is down.       1- Host Name      : APC       2- Domain Name    : somedomain.com       3- Port Speed     : Auto-negotiation       4- Accept Changes:       - Back, - Refresh, - Event Log > 4 ------- Advanced... -----------------------------------------------------------          Link is down.       1- Host Name      : APC       2- Domain Name    : somedomain.com       3- Port Speed     : Auto-negotiation       4- Accept Changes: Success       - Back, - Refresh, - Event Log > 需要注意的是TCP/IP的三个参数包括System IP,Default Gateway,Subnet Mask都必须设置，尤其网关Default Gateway不能为0.0.0.0,否则会导致网络不通。退出超级终端，则网络设置成功。 首先用ping 命令检查网络配置是否成功，如果不能Ping通，请将卡Reset,卡上有一个白色的Reset按钮，按一下，则卡重启，该重启只是卡重新加电而已，不会改变卡内的已有的任何设置。