此实验过程是使用Boson NetSim for CCNP version 6.0 BETA 1软件下做的。其中使用一台C3640和三台C2501路由器。
一个由4台路由器连接的帧中继点到点网络的操作实例
如果要每个
DTE
端子接口与对方的每个子接口通信必须进行
route rip
R1
（
R3640
）
-----------------------------------------------------------------------------------------------------------------------
Press Enter to Start
Router>
Router>
Router>
Router>enable
Router#show version
Boson Operating Simulation Software
BOSS (tm) C3600 Software (C3600-Enterprise), Version 12.1, RELEASE SOFTWARE
Copyright (c) 1998-2003 by Boson Software, Inc.
BOSS ROM: System Bootstrap, Version 12.2, RELEASE SOFTWARE
Router Uptime Is 0 days, 0 hours, 2 minutes
System restarted by power-on
System p_w_picpath file is ""flash:c3600-enterprise.12.1.boss"", booted via flash
Boson 3600 (BOSS) processor (revision 5.0)
1 Ethernet/IEEE 802.3 interface(s)
1 Fast Ethernet/IEEE 802.3 interface(s)
1 Serial network interface(s)
3 ISDN Basic Rate interface(s)
32K bytes of simulated non-volatile configuration memory.
8192K bytes of simulated System flash (Read/Write)
Configuration register is 0X2102
Router#
Router#
Router#
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#hostname R1
R1(config)#
R1(config)#
R1(config)#interface serial 0/0
R1(config-if)#no shutdown
%LINK-3-UPDOWN: Interface Serial0/0, changed state to up
%LINK-3-UPDOWN: Interface Serial0/0, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed state to down
R1(config-if)#no ip address
R1(config-if)#encapsulation frame-relay
R1(config-if)#
R1(config-if)#interface serial 0/0.2 point-to-point
R1(config-subif)#ip address 10.1.1.1 255.255.255.252
R1(config-subif)#bandwidth 64
R1(config-subif)#frame-relay interface-dlci 102
R1(config-subif)#
R1(config-subif)#
R1(config-subif)# interface serial 0/0.3 point-to-point
R1(config-subif)#ip address 10.1.1.5 255.255.255.252
R1(config-subif)#bandwidth 64
R1(config-subif)#frame-relay interface-dlci 103
R1(config-subif)#
R1(config-subif)#interface serial 0/0.4 point-to-point
R1(config-subif)#ip address 10.1.1.8 255.255.255.252
R1(config-subif)#bandwidth 64
R1(config-subif)#frame-relay interface-dlci 104
R1(config-subif)#
%LINK-3-UPDOWN: Interface Serial0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed state to up
21:49:39: %FR-5-DLCICHANGE: Interface Serial0/0.2 - DLCI 102 state changed to ACTIVE
21:49:39: %FR-5-DLCICHANGE: Interface Serial0/0.3 - DLCI 103 state changed to ACTIVE
21:49:39: %FR-5-DLCICHANGE: Interface Serial0/0.4 - DLCI 104 state changed to ACTIVE
R1(config-subif)#end
R1#
R1#
R1#show frame-relay lmi
show frame-relay lmi
LMI Statistics for interface Serial0/0 (Frame Relay DTE) LMI TYPE = CISCO
Invalid Unnumbered info 0 Invalid Prot Disc 0
Invalid dummy Call Ref 0 Invalid Msg Type 0
Invalid Status Message 0 Invalid Lock Shift 0
Invalid Information ID 0 Invalid Report IE Len 0
Invalid Report Request 0 Invalid Keep IE Len 0
Num Status Enq. Sent 160 Num Status msgs Rcvd 137
Num Update Status Rcvd 0 Num Status Timeouts 13
R1#
R1#
R1#show interface serial 0/0
Serial0/0 is up, line protocol is up
Hardware is HD64570
MTU 1500 bytes, BW 1544 Kbit, DLY 1000 usec, rely 255/255, load 1/255
Encapsulation FRAME-RELAY, loopback not set, keepalive set (10 sec)
LMI enq sent 1472, LMI stat recvd 1472, LMI upd recvd 0, DTE LMI up
LMI enq recvd 0, LMI stat sent 0, LMI upd sent 0
LMI DLCI 0 LMI type is CISCO frame relay DTE
FR SVC disabled, LAPF state down
Broadcast queue 0/64, broadcasts sent/dropped 0/0, interface broadcasts 300
Last input 00:00:00, output 00:00:00, output hang never
Last clearing of show interface counters never
Queueing strategy: fifo
Output queue 0/40, 0 drops; input queue 0/75, 0 drops
5 minute input rate 1000 bits/sec, 2 packets/sec
5 minute output rate 1000 bits/sec, 2 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 input packets with dribble condition detected
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out
R1#
R1#
R1#show interface serial 0/0.2
Serial0/0.2.2 is up, line protocol is up
Internet address is 10.1.1.1/30
MTU 1500 bytes, BW 64 Kbit, DLY 1000 usec, rely 255/255, load 1/255
Encapsulation FRAME-RELAY, loopback not set, keepalive set (10 sec)
R1#
R1#
R1#show interface serial 0/0.3
Serial0/0.3.3 is up, line protocol is up
Internet address is 10.1.1.5/30
MTU 1500 bytes, BW 64 Kbit, DLY 1000 usec, rely 255/255, load 1/255
Encapsulation FRAME-RELAY, loopback not set, keepalive set (10 sec)
R1#
R1#
R1#show interface serial 0/0.4
Serial0/0.4.4 is up, line protocol is up
Internet address is 10.1.1.8/30
MTU 1500 bytes, BW 64 Kbit, DLY 1000 usec, rely 255/255, load 1/255
Encapsulation FRAME-RELAY, loopback not set, keepalive set (10 sec)
R1#
R1#
R1#show frame-relay map
Serial0/0.2 (up): point-to-point dlci, dlci 102(0x66,0x1860), broadcast
status defined, active
Serial0/0.3 (up): point-to-point dlci, dlci 103(0x66,0x1860), broadcast
status defined, active
Serial0/0.4 (up): point-to-point dlci, dlci 104(0x66,0x1860), broadcast
status defined, active
R1#
R1#
R1#show frame-relay pvc
PVC Statistics for interface Serial0/0 (Frame Relay DTE)
DLCI = 102, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial0/0.2
input pkts 88 output pkts 57 in bytes 14504
out bytes 6037 dropped pkts 80 in FECN pkts 112
in BECN pkts 70 out FECN pkts 110 out BECN pkts 78
in DE pkts 87 out DE pkts 28
out bcast pkts 119 out bcast bytes 13809
pvc create time 00:32:04, last time pvc status changed 00:32:05
PVC Statistics for interface Serial0/0 (Frame Relay DTE)
DLCI = 103, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial0/0.3
input pkts 99 output pkts 23 in bytes 1595
out bytes 8099 dropped pkts 117 in FECN pkts 55
in BECN pkts 68 out FECN pkts 60 out BECN pkts 86
in DE pkts 93 out DE pkts 9
out bcast pkts 58 out bcast bytes 7245
pvc create time 00:32:04, last time pvc status changed 00:32:05
PVC Statistics for interface Serial0/0 (Frame Relay DTE)
DLCI = 104, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial0/0.4
input pkts 82 output pkts 105 in bytes 11271
out bytes 4828 dropped pkts 77 in FECN pkts 120
in BECN pkts 47 out FECN pkts 91 out BECN pkts 78
in DE pkts 54 out DE pkts 8
out bcast pkts 29 out bcast bytes 3340
pvc create time 00:32:04, last time pvc status changed 00:32:05
R1#
R1#
R2
（
R2501
）
-----------------------------------------------------------------------------------------------------------------------
Press Enter to Start
Router>
Router>enable
Router#show version
Boson Operating Simulation Software
BOSS (tm) C2500 Software (C2500-Enterprise), Version 12.1, RELEASE SOFTWARE
Copyright (c) 1998-2003 by Boson Software, Inc.
BOSS ROM: System Bootstrap, Version 12.2, RELEASE SOFTWARE
Router Uptime Is 0 days, 0 hours, 0 minutes
System restarted by power-on
System p_w_picpath file is ""flash:c2500-enterprise.12.1.boss"", booted via flash
Boson 2500 (BOSS) processor (revision 5.0)
1 Ethernet/IEEE 802.3 interface(s)
2 Serial network interface(s)
3 ISDN Basic Rate interface(s)
32K bytes of simulated non-volatile configuration memory.
8192K bytes of simulated System flash (Read/Write)
Configuration register is 0X2102
Router#
Router#
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#hostname R2
R2(config)#
R2(config)#
R2(config)#interface serial 0
R2(config-if)#no shutdown
%LINK-3-UPDOWN: Interface Serial0, changed state to up
R2(config-if)#no ip address
%LINK-3-UPDOWN: Interface Serial0, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0, changed state to down
R2(config-if)#encapsulation frame-relay
R2(config-if)#
R2(config-if)#
%LINK-3-UPDOWN: Interface Serial0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0, changed state to up
R2(config-if)#interface serial 0.2 point-to-point
R2(config-subif)#ip address 10.1.1.2 255.255.255.252
R2(config-subif)#bandwidth 64
R2(config-subif)#frame-relay interface-dlci 201
21:49:39: %FR-5-DLCICHANGE: Interface Serial0.2 - DLCI 201 state changed to ACTIVE
R2(config-subif)#
R2(config-subif)#interface serial 0.3 point-to-point
R2(config-subif)#ip address 10.1.1.11 255.255.255.252
R2(config-subif)#bandwidth 64
R2(config-subif)#frame-relay interface-dlci 203
R2(config-subif)#
R2(config-subif)#
R2(config-subif)#interface serial 0.4 point-to-point
R2(config-subif)#ip address 10.1.1.14 255.255.255.252
R2(config-subif)#bandwidth 64
R2(config-subif)#frame-relay interface-dlci 204
R2(config-subif)#
21:49:39: %FR-5-DLCICHANGE: Interface Serial0.3 - DLCI 203 state changed to ACTIVE
21:49:39: %FR-5-DLCICHANGE: Interface Serial0.4 - DLCI 204 state changed to ACTIVE
R2(config-subif)#end
R2#
R2#
R2#show frame-relay lmi
show frame-relay lmi
LMI Statistics for interface Serial0 (Frame Relay DTE) LMI TYPE = CISCO
Invalid Unnumbered info 0 Invalid Prot Disc 0
Invalid dummy Call Ref 0 Invalid Msg Type 0
Invalid Status Message 0 Invalid Lock Shift 0
Invalid Information ID 0 Invalid Report IE Len 0
Invalid Report Request 0 Invalid Keep IE Len 0
Num Status Enq. Sent 160 Num Status msgs Rcvd 137
Num Update Status Rcvd 0 Num Status Timeouts 13
R2#
R2#
R2#show interface serial 0
Serial0 is up, line protocol is up
Hardware is HD64570
MTU 1500 bytes, BW 1544 Kbit, DLY 1000 usec, rely 255/255, load 1/255
Encapsulation FRAME-RELAY, loopback not set, keepalive set (10 sec)
LMI enq sent 1472, LMI stat recvd 1472, LMI upd recvd 0, DTE LMI up
LMI enq recvd 0, LMI stat sent 0, LMI upd sent 0
LMI DLCI 0 LMI type is CISCO frame relay DTE
FR SVC disabled, LAPF state down
Broadcast queue 0/64, broadcasts sent/dropped 0/0, interface broadcasts 300
Last input 00:00:00, output 00:00:00, output hang never
Last clearing of show interface counters never
Queueing strategy: fifo
Output queue 0/40, 0 drops; input queue 0/75, 0 drops
5 minute input rate 1000 bits/sec, 2 packets/sec
5 minute output rate 1000 bits/sec, 2 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 input packets with dribble condition detected
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out
R2#show interface serial 0.2
Serial0.2.2 is up, line protocol is up
Internet address is 10.1.1.2/30
MTU 1500 bytes, BW 64 Kbit, DLY 1000 usec, rely 255/255, load 1/255
Encapsulation FRAME-RELAY, loopback not set, keepalive set (10 sec)
R2#
R2#
R2#show interface serial 0.3
Serial0.3.3 is up, line protocol is up
Internet address is 10.1.1.11/30
MTU 1500 bytes, BW 64 Kbit, DLY 1000 usec, rely 255/255, load 1/255
Encapsulation FRAME-RELAY, loopback not set, keepalive set (10 sec)
R2#
R2#
R2#show interface serial 0.4
Serial0.4.4 is up, line protocol is up
Internet address is 10.1.1.14/30
MTU 1500 bytes, BW 64 Kbit, DLY 1000 usec, rely 255/255, load 1/255
Encapsulation FRAME-RELAY, loopback not set, keepalive set (10 sec)
R2#
R2#
R2#show frame-relay map
Serial0.2 (up): point-to-point dlci, dlci 201(0x66,0x1860), broadcast
status defined, active
Serial0.3 (up): point-to-point dlci, dlci 203(0x66,0x1860), broadcast
status defined, active
Serial0.4 (up): point-to-point dlci, dlci 204(0x66,0x1860), broadcast
status defined, active
R2#
R2#
R2#show frame-relay pvc
PVC Statistics for interface Serial0 (Frame Relay DTE)
DLCI = 201, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial0.2
input pkts 104 output pkts 116 in bytes 9842
out bytes 7840 dropped pkts 82 in FECN pkts 33
in BECN pkts 62 out FECN pkts 61 out BECN pkts 97
in DE pkts 105 out DE pkts 112
out bcast pkts 93 out bcast bytes 3557
pvc create time 00:32:04, last time pvc status changed 00:32:05
PVC Statistics for interface Serial0 (Frame Relay DTE)
DLCI = 203, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial0.3
input pkts 66 output pkts 49 in bytes 1238
out bytes 10914 dropped pkts 95 in FECN pkts 24
in BECN pkts 89 out FECN pkts 99 out BECN pkts 13
in DE pkts 36 out DE pkts 84
out bcast pkts 114 out bcast bytes 10318
pvc create time 00:32:04, last time pvc status changed 00:32:05
PVC Statistics for interface Serial0 (Frame Relay DTE)
DLCI = 204, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial0.4
input pkts 54 output pkts 116 in bytes 5718
out bytes 5362 dropped pkts 110 in FECN pkts 68
in BECN pkts 107 out FECN pkts 75 out BECN pkts 85
in DE pkts 25 out DE pkts 85
out bcast pkts 111 out bcast bytes 11746
pvc create time 00:32:04, last time pvc status changed 00:32:05
R2#
R2#
R3
（
R2501
）
-----------------------------------------------------------------------------------------------------------------------
Press Enter to Start
Router>
Router>
Router>enable
Router#show version
Boson Operating Simulation Software
BOSS (tm) C2500 Software (C2500-Enterprise), Version 12.1, RELEASE SOFTWARE
Copyright (c) 1998-2003 by Boson Software, Inc.
BOSS ROM: System Bootstrap, Version 12.2, RELEASE SOFTWARE
Router Uptime Is 0 days, 0 hours, 14 minutes
System restarted by power-on
System p_w_picpath file is ""flash:c2500-enterprise.12.1.boss"", booted via flash
Boson 2500 (BOSS) processor (revision 5.0)
1 Ethernet/IEEE 802.3 interface(s)
2 Serial network interface(s)
3 ISDN Basic Rate interface(s)
32K bytes of simulated non-volatile configuration memory.
8192K bytes of simulated System flash (Read/Write)
Configuration register is 0X2102
Router#
Router#
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#hostname R3
R3(config)#
R3(config)#
R3(config)#interface serial 0
R3(config-if)#no shutdown
%LINK-3-UPDOWN: Interface Serial0, changed state to up
R3(config-if)#no ip address
%LINK-3-UPDOWN: Interface Serial0, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0, changed state to down
R3(config-if)#encapsulation frame-relay
%LINK-3-UPDOWN: Interface Serial0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0, changed state to up
R3(config-if)#
R3(config-if)#interface serial 0.2 point-to-point
R3(config-subif)#ip address 10.1.1.6 255.255.255.252
R3(config-subif)#bandwidth 64
R3(config-subif)#frame-relay interface-dlci 301
21:49:39: %FR-5-DLCICHANGE: Interface Serial0.2 - DLCI 301 state changed to ACTIVE
R3(config-subif)#
R3(config-subif)#
R3(config-subif)#interface serial 0.3 point-to-point
R3(config-subif)#ip address 10.1.1.12 255.255.255.252
R3(config-subif)#bandwidth 64
R3(config-subif)#frame-relay interface-dlci 302
21:49:39: %FR-5-DLCICHANGE: Interface Serial0.3 - DLCI 302 state changed to ACTIVE
R3(config-subif)#
R3(config-subif)#
R3(config-subif)#interface serial 0.4 point-to-point
R3(config-subif)#ip address 10.1.1.17 255.255.255.252
R3(config-subif)#bandwidth 64
R3(config-subif)#frame-relay interface-dlci 304
R3(config-subif)#
21:49:39: %FR-5-DLCICHANGE: Interface Serial0.4 - DLCI 304 state changed to ACTIVE
R3(config-subif)#end
R3#
R3#
R3#show frame-relay lmi
show frame-relay lmi
LMI Statistics for interface Serial0 (Frame Relay DTE) LMI TYPE = CISCO
Invalid Unnumbered info 0 Invalid Prot Disc 0
Invalid dummy Call Ref 0 Invalid Msg Type 0
Invalid Status Message 0 Invalid Lock Shift 0
Invalid Information ID 0 Invalid Report IE Len 0
Invalid Report Request 0 Invalid Keep IE Len 0
Num Status Enq. Sent 160 Num Status msgs Rcvd 137
Num Update Status Rcvd 0 Num Status Timeouts 13
R3#
R3#
R3#show interface serial 0
Serial0 is up, line protocol is up
Hardware is HD64570
MTU 1500 bytes, BW 1544 Kbit, DLY 1000 usec, rely 255/255, load 1/255
Encapsulation FRAME-RELAY, loopback not set, keepalive set (10 sec)
LMI enq sent 1472, LMI stat recvd 1472, LMI upd recvd 0, DTE LMI up
LMI enq recvd 0, LMI stat sent 0, LMI upd sent 0
LMI DLCI 0 LMI type is CISCO frame relay DTE
FR SVC disabled, LAPF state down
Broadcast queue 0/64, broadcasts sent/dropped 0/0, interface broadcasts 300
Last input 00:00:00, output 00:00:00, output hang never
Last clearing of show interface counters never
Queueing strategy: fifo
Output queue 0/40, 0 drops; input queue 0/75, 0 drops
5 minute input rate 1000 bits/sec, 2 packets/sec
5 minute output rate 1000 bits/sec, 2 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 input packets with dribble condition detected
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out
R3#
R3#
R3#show interface serial 0.2
Serial0.2.2 is up, line protocol is up
Internet address is 10.1.1.6/30
MTU 1500 bytes, BW 64 Kbit, DLY 1000 usec, rely 255/255, load 1/255
Encapsulation FRAME-RELAY, loopback not set, keepalive set (10 sec)
R3#
R3#
R3#show interface serial 0.3
Serial0.3.3 is up, line protocol is up
Internet address is 10.1.1.12/30
MTU 1500 bytes, BW 64 Kbit, DLY 1000 usec, rely 255/255, load 1/255
Encapsulation FRAME-RELAY, loopback not set, keepalive set (10 sec)
R3#
R3#
R3#show interface serial 0.4
Serial0.4.4 is up, line protocol is up
Internet address is 10.1.1.17/30
MTU 1500 bytes, BW 64 Kbit, DLY 1000 usec, rely 255/255, load 1/255
Encapsulation FRAME-RELAY, loopback not set, keepalive set (10 sec)
R3#
R3#
R3#show frame-relay map
Serial0.3 (up): point-to-point dlci, dlci 302(0x66,0x1860), broadcast
status defined, active
Serial0.2 (up): point-to-point dlci, dlci 301(0x66,0x1860), broadcast
status defined, active
Serial0.4 (up): point-to-point dlci, dlci 304(0x66,0x1860), broadcast
status defined, active
R3#
R3#
R3#show frame-relay pvc
PVC Statistics for interface Serial0 (Frame Relay DTE)
DLCI = 301, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial0.2
input pkts 85 output pkts 78 in bytes 1056
out bytes 7303 dropped pkts 117 in FECN pkts 99
in BECN pkts 90 out FECN pkts 117 out BECN pkts 37
in DE pkts 71 out DE pkts 120
out bcast pkts 92 out bcast bytes 13807
pvc create time 00:32:04, last time pvc status changed 00:32:05
PVC Statistics for interface Serial0 (Frame Relay DTE)
DLCI = 302, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial0.3
input pkts 49 output pkts 37 in bytes 12636
out bytes 5284 dropped pkts 119 in FECN pkts 47
in BECN pkts 59 out FECN pkts 78 out BECN pkts 54
in DE pkts 7 out DE pkts 28
out bcast pkts 29 out bcast bytes 2784
pvc create time 00:32:04, last time pvc status changed 00:32:05
PVC Statistics for interface Serial0 (Frame Relay DTE)
DLCI = 304, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial0.4
input pkts 37 output pkts 89 in bytes 12778
out bytes 14840 dropped pkts 72 in FECN pkts 102
in BECN pkts 100 out FECN pkts 18 out BECN pkts 27
in DE pkts 33 out DE pkts 14
out bcast pkts 71 out bcast bytes 12838
pvc create time 00:32:04, last time pvc status changed 00:32:05
R3#
R3#
R4
（
R2501
）
-----------------------------------------------------------------------------------------------------------------------
Press Enter to Start
Router>
Router>
Router>enable
Router#show version
Boson Operating Simulation Software
BOSS (tm) C2500 Software (C2500-Enterprise), Version 12.1, RELEASE SOFTWARE
Copyright (c) 1998-2003 by Boson Software, Inc.
BOSS ROM: System Bootstrap, Version 12.2, RELEASE SOFTWARE
Router Uptime Is 0 days, 0 hours, 18 minutes
System restarted by power-on
System p_w_picpath file is ""flash:c2500-enterprise.12.1.boss"", booted via flash
Boson 2500 (BOSS) processor (revision 5.0)
1 Ethernet/IEEE 802.3 interface(s)
2 Serial network interface(s)
3 ISDN Basic Rate interface(s)
32K bytes of simulated non-volatile configuration memory.
8192K bytes of simulated System flash (Read/Write)
Configuration register is 0X2102
Router#
Router#
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#hostname R4
R4(config)#
R4(config)#
R4(config)#interface serial 0
R4(config-if)#no shutdown
%LINK-3-UPDOWN: Interface Serial0, changed state to up
R4(config-if)#no ip address
%LINK-3-UPDOWN: Interface Serial0, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0, changed state to down
R4(config-if)#encapsulation frame-relay
%LINK-3-UPDOWN: Interface Serial0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0, changed state to up
R4(config-if)#
R4(config-if)#
R4(config-if)#interface serial 0.2 point-to-point
R4(config-subif)#ip address 10.1.1.9 255.255.255.252
R4(config-subif)#bandwidth 64
R4(config-subif)#frame-relay interface-dlci 401
21:49:39: %FR-5-DLCICHANGE: Interface Serial0.2 - DLCI 401 state changed to ACTIVE
R4(config-subif)#
R4(config-subif)#
R4(config-subif)#interface serial 0.3 point-to-point
R4(config-subif)#ip address 10.1.1.15 255.255.255.252
R4(config-subif)#bandwidth 64
R4(config-subif)#frame-relay interface-dlci 402
21:49:39: %FR-5-DLCICHANGE: Interface Serial0.3 - DLCI 402 state changed to ACTIVE
R4(config-subif)#
R4(config-subif)#
R4(config-subif)#interface serial 0.4 point-to-point
R4(config-subif)#ip address 10.1.1.18 255.255.255.252
R4(config-subif)#bandwidth 64
R4(config-subif)#frame-relay interface-dlci 403
21:49:39: %FR-5-DLCICHANGE: Interface Serial0.4 - DLCI 403 state changed to ACTIVE
R4(config-subif)#
R4(config-subif)#
R4(config-subif)#end
R4#
R4#
R4#show frame-relay lmi
show frame-relay lmi
LMI Statistics for interface Serial0 (Frame Relay DTE) LMI TYPE = CISCO
Invalid Unnumbered info 0 Invalid Prot Disc 0
Invalid dummy Call Ref 0 Invalid Msg Type 0
Invalid Status Message 0 Invalid Lock Shift 0
Invalid Information ID 0 Invalid Report IE Len 0
Invalid Report Request 0 Invalid Keep IE Len 0
Num Status Enq. Sent 160 Num Status msgs Rcvd 137
Num Update Status Rcvd 0 Num Status Timeouts 13
R4#
R4#
R4#show interface serial 0
Serial0 is up, line protocol is up
Hardware is HD64570
MTU 1500 bytes, BW 1544 Kbit, DLY 1000 usec, rely 255/255, load 1/255
Encapsulation FRAME-RELAY, loopback not set, keepalive set (10 sec)
LMI enq sent 1472, LMI stat recvd 1472, LMI upd recvd 0, DTE LMI up
LMI enq recvd 0, LMI stat sent 0, LMI upd sent 0
LMI DLCI 0 LMI type is CISCO frame relay DTE
FR SVC disabled, LAPF state down
Broadcast queue 0/64, broadcasts sent/dropped 0/0, interface broadcasts 300
Last input 00:00:00, output 00:00:00, output hang never
Last clearing of show interface counters never
Queueing strategy: fifo
Output queue 0/40, 0 drops; input queue 0/75, 0 drops
5 minute input rate 1000 bits/sec, 2 packets/sec
5 minute output rate 1000 bits/sec, 2 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 input packets with dribble condition detected
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out
R4#
R4#
R4#show interface serial 0.2
Serial0.2.2 is up, line protocol is up
Internet address is 10.1.1.9/30
MTU 1500 bytes, BW 64 Kbit, DLY 1000 usec, rely 255/255, load 1/255
Encapsulation FRAME-RELAY, loopback not set, keepalive set (10 sec)
R4#
R4#
R4#show interface serial 0.2
Serial0.2.2 is up, line protocol is up
Internet address is 10.1.1.9/30
MTU 1500 bytes, BW 64 Kbit, DLY 1000 usec, rely 255/255, load 1/255
Encapsulation FRAME-RELAY, loopback not set, keepalive set (10 sec)
R4#
R4#
R4#show interface serial 0.3
Serial0.3.3 is up, line protocol is up
Internet address is 10.1.1.15/30
MTU 1500 bytes, BW 64 Kbit, DLY 1000 usec, rely 255/255, load 1/255
Encapsulation FRAME-RELAY, loopback not set, keepalive set (10 sec)
R4#
R4#
R4#show interface serial 0.4
Serial0.4.4 is up, line protocol is up
Internet address is 10.1.1.18/30
MTU 1500 bytes, BW 64 Kbit, DLY 1000 usec, rely 255/255, load 1/255
Encapsulation FRAME-RELAY, loopback not set, keepalive set (10 sec)
R4#
R4#
R4#show frame-relay map
Serial0.4 (up): point-to-point dlci, dlci 403(0x66,0x1860), broadcast
status defined, active
Serial0.3 (up): point-to-point dlci, dlci 402(0x66,0x1860), broadcast
status defined, active
Serial0.2 (up): point-to-point dlci, dlci 401(0x66,0x1860), broadcast
status defined, active
R4#
R4#
R4#show frame-relay pvc
PVC Statistics for interface Serial0 (Frame Relay DTE)
DLCI = 401, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial0.2
input pkts 6 output pkts 88 in bytes 5436
out bytes 6109 dropped pkts 98 in FECN pkts 45
in BECN pkts 56 out FECN pkts 87 out BECN pkts 79
in DE pkts 40 out DE pkts 71
out bcast pkts 10 out bcast bytes 935
pvc create time 00:32:04, last time pvc status changed 00:32:05
PVC Statistics for interface Serial0 (Frame Relay DTE)
DLCI = 402, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial0.3
input pkts 72 output pkts 92 in bytes 14735
out bytes 7914 dropped pkts 111 in FECN pkts 64
in BECN pkts 118 out FECN pkts 41 out BECN pkts 100
in DE pkts 41 out DE pkts 67
out bcast pkts 53 out bcast bytes 11503
pvc create time 00:32:04, last time pvc status changed 00:32:05
PVC Statistics for interface Serial0 (Frame Relay DTE)
DLCI = 403, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial0.4
input pkts 57 output pkts 108 in bytes 8549
out bytes 11623 dropped pkts 109 in FECN pkts 100
in BECN pkts 9 out FECN pkts 47 out BECN pkts 81
in DE pkts 98 out DE pkts 101
out bcast pkts 5 out bcast bytes 6963
pvc create time 00:32:04, last time pvc status changed 00:32:05
R4#
R4#
R4#