这部分文档是关于T1/E1控制器配置命令。这些命令取决于你是否配置E1/T1控制器。下表列出了每一种控制器的支持情况。
cablelength long
为电缆线路距离200米的CSU类型T1接口配置传输和接受级别。使用
cablelength long 去配置，使用
no cablelength long去恢复默认。
cablelength long {gain26 | gain36} {-15db | -22.5db | -7.5db | 0db
}
cablelength long
cablelength long
参数描述：
gain26 | gain36 置接受灵敏度。如果硬件固定了36，则命令不起作用
-15db | -22.5db | -7.5db | 0db 设置传输衰减系数
默认值：
接受灵敏值在CLI显示为26，硬件绑定36
传输衰减值为0
使用指南：
这个命令仅仅被类型为CSU（长短距）的T1控制器所支持。如果你启用ca
blelength long命令在DSX-1（短距离）接口，这个命令将会被拒绝。
使用
show controller T1命令去确定一个控制器是否为CSU类型。
这个指令使用于Voice over Frame Relay, Voice over ATM, and Voice over HDLC 在 Cisco MC3810 MFT上
在Cisco MC3810 MFT and DVM 硬件中，接收灵敏固定在36db并且不受
cablelength long {
gain26
|
gain36} 命令的影响。CISCO建议使用
gain 36值以至命令入口匹配实际值。
传输衰减值最好通过实验获得。如果远端设备接收信号太强，通过使用增加衰减值来减小传输级别。
下面的例子通过改变CLI接收灵敏度去匹配硬件实际接收灵敏度，对控制器T1 0接口发送信号进行15db的衰减。
controller T1 0
cablelength long gain36 -15db
cablelength long gain36 -15db
cablelength short
为电缆线路距离为200米或小于200米的DSX-1类型T1接口配置传输衰减级别。使用
cablelength short 去配置，使用
no cablelength short去恢复默认。
cablelength short {133 | 266 | 399 | 533 | 655
}
no cablelength short
no cablelength short
默认线缆距离为133。
使用指南：
这个命令仅仅被类型为DSX-1（短距离）的T1控制器所支持。如果你启用cablelength long命令在CSU（长距离）接口上，这个命令将会被拒绝。
使用show controller T1命令去确定一个控制器是否为CSU类型。
这个指令使用于Voice over Frame Relay，Voice over ATM，and Voice over HDLC在 Cisco MC3810 MFT上
下面的例子是为电缆距离在134~266英尺长，在T1接口上设置合适传输衰减值。
controller T1 1
cablelength short 266
channel-group
在T1或E1接口上配置Voice时隙列表，使用channel-group去配置，no channel-group去删除。
channel-group
channel-no
timeslots
timeslot-list speed
{56
| 64
}
no channel-group channel-no timeslots timeslot-list speed {56 | 64 }
no channel-group channel-no timeslots timeslot-list speed {56 | 64 }
参数介绍：
channel-no 通道组的ID标识号，可用范围为0~31
timeslots-list 时隙TS0被包含在通道组，可用的时隙T1（1~24），E1（1~15，17~31）
speed{56|54} 可选项
默认T1/E1为64kbps
clock source
clock source
{line
|
internal
| loop-timed
}
参数解释：
|
line
|
The controller recovers external clock from the line and provides the recovered clock to the internal (system) clock generator. The line value is the default clock source for the MFT.
|
|
internal
|
The controller synchronizes itself to the internal (system) clock. The internal value is the default clock source for the DVM.
|
|
loop-timed
|
The T1/E1 controller recovers clock from the Rx (line) and uses it for Tx. This setting decouples the controller clock from the system-wide clock set with the
network-clock-select command. The loop-timed clock enables the digital voice module (DVM) to connect to a PBX and to connect the Multiflex Trunk (MFT) to a central office when both the PBX and the central office function as DCE clock sources. This situation assumes that the PBX also takes the clocking from the central office thereby synchronizing the clocks on the DVM and the MFT.
|
默认（line）外部时钟源在E1 0/T1 0
（internal）内部时钟源在e1 1/T1 1
framing (E1/T1 controller)
Use the framing controller configuration command to select the frame type for the E1 or T1 data line.
For T1 lines:
framing
{
sf |
esf
}
For E1 lines:
framing
{
crc4
|
no-crc4
} [
australia
]
Syntax Description
|
sf
|
Super frame is the T1 frame type.
|
|
esf
|
Extended super frame is the T1 frame type.
|
|
crc4
|
CRC4 frame is the E1 frame type.
|
|
no-crc4
|
CRC4 frame is not the E1 frame type.
|
|
australia
|
(Optional) E1 frame type used in Australia.
|
Defaults
Super frame is the default on a T1 line.
CRC4 frame is the default on an E1 line.
linecode
Use the
linecode controller command to select the line-code type for a T1 or E1 line.Use the
no form of the command to restore the default.
For T1 lines:
linecode
{ami
| b8zs
}
no linecode
{ami
| b8zs
}
For E1 lines:
linecode
{ami
| hdb3
}
no linecode
{ami
| hdb3
}
Syntax Description
|
ami
|
Alternate mark inversion (AMI) line-code type. Valid for both T1 and E1 controllers.
|
|
b8zs
|
B8ZS line-cole type. Valid for T1 controller only.
|
|
hdb3
|
High-density bipolar 3 (HDB3) line-code type. Valid for E1 controller only.
|
Defaults
HDB3 line code is the default for E1 lines.
AMI line code is the default for T1 lines.
loop-detect
To enable loop detection for T1, use the
loop-detect controller configuration command. Use the
no form of the command to cancel the loop detect operation.
loop-detect
no loop-detect
no loop-detect
Syntax Description
This command has no arguments or keywords.
Defaults
Loop detection is disabled.
loopback
Use the
loopback controller configuration command to put the T1 or E1 line into loopback mode. Use the
no form of this command to disable loopback mode.
For E1:
loopback
{local
| line
| payload
}
no loopback {local | line | payload }
no loopback {local | line | payload }
For T1:
loopback
{local
| remote
| line
| payload
}
no loopback {local | remote | line | payload }
no loopback {local | remote | line | payload }
Syntax Description
|
local
|
The controller loops the internal signal back to the internal bus in the Cisco MC3810.
|
|
line
|
The controller loops the external line signal back toward the network without reframing the DS1 signal.
|
|
payload
|
The controller loops the external line signal back toward the network and reframes the DS1 signal.
|
|
remote
|
For T1 only. The T1 controller sends the inband loop-up code to the remote device, which is assumed to have CSU functionality. The remote device detects the code and loops the line back to the Cisco MC3810.
If the Cisco MC3810 detects its own code, the loopback is successful. If the Cisco MC3810 does not detect its own code within 10 seconds, the loopback is not successful.
|
Defaults
Local is the default for T1 and E1 lines.
mode
To set the mode of the T1/E1 controller and enter specific configuration commands for each mode type, use the mode controller configuration command. Use the no form of this command to restore the default mode of the controller.
mode {atm | cas | ccs cross-connect | ccs frame-forwarding
}
no mode {atm | cas | ccs cross-connect | ccs frame-forwarding }
no mode {atm | cas | ccs cross-connect | ccs frame-forwarding }
Syntax Description
|
atm
|
Sets the controller into ATM mode and creates an ATM interface (ATM 0) on the Cisco MC3810. When ATM mode is enabled, no channel groups, voice groups, PRI groups, or TDM groups are possible, because ATM occupies all the DS0s on the T1/E1 trunk.
When you set the controller to ATM mode, the controller framing is automatically set to ESF for T1 or CRC4 for E1. The linecode is automatically set to B8ZS for T1 or HDBC for E1. When you remove ATM mode by entering the no mode atm command, ATM interface 0 is deleted.
ATM mode is supported on controller 0 only (T1 0 or E1 0).
|
|
cas
|
Sets the controller into channel associated signaling (CAS) mode and enables the voice-group command, which allows you to create voice groups.
CAS mode is supported on controllers 0 and 1.
|
|
ccs cross-connect
|
Sets the controller into transparent Common Channel Signaling (CCS) mode and enables the voice-group command, which allows you to create voice groups.
HDLC frames from a CCS D-channel timeslot are cross-connected to a TDM group or to a serial port.
Transparent CCS mode is supported on controller 1 only (T1 1 or E1 1). |
|
ccs frame-forwarding
|
Sets the controller into transparent CCS mode and enables the voice-group command, which allows you to create voice groups. It creates interface serial 1:x, where x is 23 on controller T1 1 and x is 15 on controller E1 1.
HDLC frames from a CCS D channel are forwarded to a preconfigured Frame Relay DLCI or to an ATM PVC.
Transparent CCS mode is supported on controller 1 only (T1 1 or E1 1) . |
Defaults
No mode is configured.
Usage Guidelines
This command applies to the Cisco MC3810 with the digital voice module (DVM) installed.
If no mode is configured, only channel groups, PRI groups, and TDM groups (in data mode) can be configured. Channel groups and TDM groups are created using the
channel group and
tdm-group commands, respectively.
On the Cisco MC3810, some DS0s are used exclusively for different signaling modes. DS0 channels have the following limitations when mixing different applications (such as voice and data) on the same network trunk:
•
On E1 controllers, DS0 16 is used exclusively for either CAS or transparent CCS, depending on which mode is configured. DS0 16 is identified as serial 1:15 in transparent CCS.
On E1 controllers, DS0 16 is used exclusively for either CAS or transparent CCS, depending on which mode is configured. DS0 16 is identified as serial 1:15 in transparent CCS.
•
On T1 controllers, DS0 24 is used exclusively for transparent CCS, and is identified as serial 1:23.
On T1 controllers, DS0 24 is used exclusively for transparent CCS, and is identified as serial 1:23.
The
no form of the command is not accepted if there are voice groups configured on the controller.
pri-group
To specify ISDN Primary Rate Interface (PRI) on a channelized T1 or E1 controller, use the
pri-group
controller configuration command. Use the
no
form of this command to remove the ISDN-PRI configuration.
pri-group [timeslots
range
]
no pri-group
no pri-group
Syntax Description
|
timeslots
range
|
(Optional) Specifies a single range of values from 1 to 23 for channelized T1 and from 1 to 31 for channelized E1.
|
Defaults
No ISDN-PRI configuration is configured.
Usage Guidelines
This command applies to the configuration of Voice over Frame Relay, Voice over ATM, and Voice over HDLC on the Cisco MC3810.
Before you enter the
pri-group command, you must specify an ISDN-PRI switch type and an E1 or T1 controller. Only one pri group can be configured on a controller.
Examples
The following example configures ISDN-PRI on all timeslots of controller T1 1 on a Cisco MC3810:
isdn switch-type primary-qsig-master
controller T1 1
pri-group timeslots 1-23
tdm-group
To configure a list of timeslots for creating clear channel groups (pass-through) for Time Division Multiplexing (TDM) cross-connect, use the tdm-group controller configuration command. Use the no form of this command to delete a clear channel group.tdm-group tdm-group-no timeslots timeslot-list [type {e&m | fxs [loop-start | ground-start ] | fxo [loop-start | ground-start ] | fxs-melcas | fxo-melcas | e&m-melcas } ]no tdm-group tdm-group-noSyntax Description
Defaults
No TDM group is configured.Usage Guidelines
This command applies to the configuration of Voice over Frame Relay, Voice over ATM, and Voice over HDLC on the Cisco MC3810.
NoteExamples
The following example configures TDM group number 20, containing DS0s 2, 5, 7, 9-12, and 21, on controller T1 1 to support FXS ground-start signaling:controller T1 1mode castdm-group 20 timeslots 2,5,7,9-12,21 type fxs ground-startvoice-group
To configure a list of voice ports for Channel Associated Signaling (CAS) or transparent Common Channel Signaling (CCS) on the T1/E1 controller, use the voice-group controller configuration command. Use the no form of this command to delete voice groups.voice-group voice-group-no timeslots timeslot-list type {e&m-immediate | e&m-delay | e&m-wink | e&m-melcas | fxs-ground-start | fxs-loop-start | fxs-melcas | fxo-ground-start | fxo-loop-start | fxo-melcas | ext-sig-master | ext-sig-slave }no voice-group voice-group-no timeslots timeslot-listSyntax Description
Defaults
No voice group is configured.Command Mode
Controller configurationCommand History
Usage Guidelines
This command applies to the configuration of Voice over Frame Relay, Voice over ATM, and Voice over HDLC on the Cisco MC3810.This command is only available if the mode cas or mode ccs command is enabled.
NoteExamples
The following example configures voice group number 10, containing DS0s 1 through 12, on controller T1 0 to support E&M immediate-start signalingcontroller t1 0mode casvoice-group 10 timeslots 1-12 e&m-immediate