aruba AP初始化
| |
AP可通过控制器获取IP地址，也可通过Windows DHCP等服务获取IP，但后者必须配置dhcp option 60和43，本文仅描述AP初始化。一般新的AP无法获取IP可能是因为内置配置没有释放（只有2个状态灯亮，WAN不亮），需通过以下步骤初始化。
控制器Aruba2400，AP61
需要通过AP控制器初始化AP设备，通过telnet登录控制器的2300端口（端口已默认开启，登录后提示符为soe>），连接AP所在控制器的端口。
在AP控制器上确保下列命令已存在
telnet cli
telnet soe //这条至关重要，如果没有可能无法连接2300端口
netservice svc-telnet tcp 23
登录AP控制器
telnet 172.17.0.1 2300 //通过此命令登录到AP上
User: admin
Password: ********
Available commands:
connect
exit (no args)
soe>connect 1/0
Connecting to 1/0 at 9600 baud 8N1 //AP控制器模拟超级终端连接AP
Type "~." to disconnect //表示AP没有连上AP控制器
~ # //表示AP连在AP控制器上，此时拔掉AP网线，并插上，立即会出现如下提示
APBoot 1.5.5 (build [email protected])
Built: 2006-02-24 18:29:36 (with gcc 3.3.1)
CPU: AR2313 MIPS-32 at 180 MHz: 16 kB I-Cache 16 kB D-Cache
Board: Merlot, Local Bus at 90 MHz
DRAM: 32 MB
POST: passed
FLASH: 4 MB
Net: en0 lo0
Hit
apboot>
apboot> //在此提示符下键入回复出厂的命令
apboot>purgeenv //恢复出厂
apboot>save //保存
apboot>reset //重启
?imed-out waiting for a command, reseting...
APBoot 1.5.5 (build [email protected])
Built: 2006-02-24 18:29:36 (with gcc 3.3.1)
CPU: AR2313 MIPS-32 at 180 MHz: 16 kB I-Cache 16 kB D-Cache
Board: Merlot, Local Bus at 90 MHz
DRAM: 32 MB
POST: passed
FLASH: 4 MB
Net: en0 lo0
Hit
Loading FLASH image @ 0xbfc40000... not present
Loading FLASH image @ 0xbfc80000...
Verifying checksum...
Booting image...
........................
Aruba Networks
ArubaOS Version 3.3.3.1 (build 22322 / label #22322)
Built by p4build@trinidad on 2009-09-08 at 11:52:27 PDT (gcc version 3.4.3)
BOARD - Merlot
CPU frequency 180.00 MHz
Using 90.000 MHz high precision timer. cycles_per_jiffy=180000
Memory: 27024k/32768k available (1841k kernel code, 5728k reserved, 419k data, 1996k init, 0k highmem)
available.
detected lzma initramfs
initramfs: LZMA lc=3,lp=0,pb=2,dictSize=8388608,origSize=10236928
LZMA initramfs by Ming-Ching Tiew
..........................................................................................
wdt: registered with refresh
physmap flash device: 400000 at 1fc00000
Macronix Flash MX29LV320A (Top) (User Locked)
phys_mapped_flash: Found 1 x16 devices at 0x0 in 8-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
number of CFI chips: 1
bond0: Atheros AR2313: 00:24:6c:c1:22:ba, irq 4
AP xml model 5, num_radios 1 (jiffies 7035)
radio 0: band 2 ant 0 max_ssid 16
ath_hal: module license 'Proprietary' taints kernel.
ath_hal: 0.9.17.1 (AR5212, AR5312, RF5111, RF5112, RF2413, RF5413)
ath_rate_atheros: Version 2.0.1
Copyright (c) 2001-2004 Atheros Communications, Inc, All Rights Reserved
ath_dfs: Version 2.0.0
Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved
ath_ahb: 0.9.4.5 (Atheros/multi-bss)
devid=0x58
AR2313_REV8
wifi0: Base BSSID 00:24:6c:92:2b:a0, 16 available BSSID(s)
edev->dev_addr=00:24:6c:c1:22:ba
wifi0: AP type AP-61, radio 0, max_bssids 16
wifi0: Atheros 2313 WiSoC: mem=0xb8500000, irq=5 //启动完成
此时AP控制器的三个状态灯就全亮了，电脑可以搜索到AP的ssid“aruba-ap