华为多臂路由配置_第1张图片

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CLIENT1属于vlan10

CLIENT2属于vlan20

接下来看LSW1的配置

首先

vlan batch 10 20 100 to 101  #创建需要使用的所有vlan

[Huawei-Ethernet0/0/4]dis this             #连接CLIENT1的4口
#
interface Ethernet0/0/4
 port hybrid pvid vlan 10                       #这里使用hybird接口,且PVID为vlan 10,端口接收数据时会打上
                                                                   vlan 10的标签 

port hybrid untagged vlan 10 20 100     #这里配置此端口发送带vlan 10,20,100标签的数据时,剥掉标签

                                                                      发送
#

 

[Huawei-Ethernet0/0/6]di this           

#                                           
interface Ethernet0/0/6                       #这里的配置与4口差不多
 port hybrid pvid vlan 20
 port hybrid untagged vlan 10 20 101

#

 

[Huawei-GigabitEthernet0/0/1]dis this         
#
interface GigabitEthernet0/0/1               #连接路由器的1口
 port link-type trunk                                 #端口类型trunk
 port trunk pvid vlan 100                        #端口PVID100,接收时打上vlan100的标签
 port trunk allow-pass vlan 2 to 4094    #允许所有vlan通过
#

 

[Huawei-GigabitEthernet0/0/2]dis this
#
interface GigabitEthernet0/0/2           #连接路由器的2口,与1口类似
 port link-type trunk
 port trunk pvid vlan 101
 port trunk allow-pass vlan 2 to 4094
#

 

#
interface Vlanif10                                                          #vlan10下的网关
 ip address 192.168.10.254 255.255.255.0
 dhcp select interface                                                  #vlan 10的dhcp配置
#
interface Vlanif20                                                         #vlan 20下的网关
 ip address 192.168.20.254 255.255.255.0
 dhcp select interface
#
interface Vlanif100
 ip address 192.168.100.254 255.255.255.0
#
interface Vlanif101
 ip address 192.168.101.254 255.255.255.0
#

 

#                                                                                  #静态路由
ip route-static 0.0.0.0 0.0.0.0 192.168.100.1                      
ip route-static 0.0.0.0 0.0.0.0 192.168.101.1
ip route-static 192.168.10.0 255.255.255.0 Ethernet0/0/4
ip route-static 192.168.20.0 255.255.255.0 Ethernet0/0/6
#

 

AR1上只做了如下设置

#
interface GigabitEthernet0/0/0
 ip address 192.168.100.1 255.255.255.0
#
interface GigabitEthernet0/0/1
 ip address 192.168.101.1 255.255.255.0
#

 

#
ip route-static 192.168.10.0 255.255.255.0 192.168.100.254
ip route-static 192.168.20.0 255.255.255.0 192.168.101.254
#

在client1上面pingclient2

华为多臂路由配置_第2张图片

要特别注意hybird接口的使用