[嵌入式linux]CAN/CAN FD配置及测试

How to test CAN/CANFD in linux

The Linux kernel supports CAN with the SocketCAN framework.

Driver installation

$ make linux-menuconfig
Networking support  --->
       CAN bus subsystem support ---> 
        --- CAN bus subsystem support
           Raw CAN Protocol (raw access with CAN-ID filtering)
           Broadcast Manager CAN Protocol (with content filtering)
              CAN Device Drivers  --->
                   Virtual Local CAN Interface (vcan)
                   Platform CAN drivers with Netlink support
                  [*]   CAN bit-timing calculation   
                   Microchip 251x series SPI CAN Controller

RootFs

You need to prepare 3 components for the root file system.

要在linux下面配置和测试CAN，需要安装以下三个组件。

• iproute2 （配置CAN接口时需要）
• libsocketcan（使用CAN必须）
• can-utils (CAN的测试小工具，linux下测试CAN比较好用应用程序)

下面提供buildroot和源码安装两种方式，根据自己的情况取其一就可以了。

iproute2

• buildroot

Package Selection for the target  --->
    Networking applications  --->
        [*] iproute2

• Source install
  • Download:https://mirrors.edge.kernel.org/pub/linux/utils/net/iproute2/
  • Edit config.mk : Modify "AR" and "CC" according to the compiler you are using.

    ifeq ("$(origin V)", "command line")
      VERBOSE = $(V)
    endif
    ifndef VERBOSE
      VERBOSE = 0
    endif
    ifeq ($(VERBOSE),1)
      Q =
    else
      Q = @
    endif
    
    ifeq ($(VERBOSE), 0)
        QUIET_CC       = @echo '    CC       '$@;
        QUIET_AR       = @echo '    AR       '$@;
        QUIET_LINK     = @echo '    LINK     '$@;
        QUIET_YACC     = @echo '    YACC     '$@;
        QUIET_LEX      = @echo '    LEX      '$@;
    endif
    AR:=aarch64-linux-gnu-ar
    CC:=aarch64-linux-gnu-gcc
    TC_CONFIG_NO_XT:=y
    IP_CONFIG_SETNS:=y
    CFLAGS += -DHAVE_SETNS
    CFLAGS += -DNEED_STRLCPY
    
    %.o: %.c
    	$(QUIET_CC)$(CC) $(CFLAGS) $(EXTRA_CFLAGS) $(CPPFLAGS) -c -o $@ $<
    TC_CONFIG_XT:=n

     

  • make&install

    cd ${BR_BINARIES_DIR}/iproute2-4.20.0
    make clean
    make
    make install DESTDIR=$TMP_ROOT_DIR

     

libsocktcan

• buildroot

Target packages  --->
        Libraries  --->
            Networking  --->
                [*] libsocketcan

can-utils

• buildroot

Target packages  --->
        Networking applications  --->
            [*] can-utils

Usage of can-utils

• Link up
  1. CAN 2.0 link up

     ip link set can0 up type can bitrate 100000

      

  2. CAN FD link up

     ip link set can0 up type can bitrate 500000 dbitrate 2000000  fd on

     Note: An error occurs when you try to set the bitrate with an old Linux kernel. In that case, echo 125000 > /sys/devices/platform/FlexCAN.0/bitrate was reported to be a good alternative.
  • • If the following error occurs when you do the last instruction :

      ip: either "dev" is duplicate, or "type" is garbage
      

      check that this command: # which ip return this message: /sbin/ip and not this one : /bin/ip If the binary is installed in /bin instead of /sbin, the executable file is a link to busybox and the command to set the bitrate doesn't work on busybox, so try the following instructions: $ make busybox-clean $ make busybox-dirclean $ make menuconfig Package Selection for the target ---> Networking applications ---> [*] iproute2 $ make Then, reflash your rootfs.

1. Send can frames

   #The following command sends 3 bytes on the bus (0x1E, 0x10, 0x10) with the identifier 500.
   cansend can0 500#1E.10.10
   
   #You can send a remote request message
   cansend can0 500#R 
   
   #gen and send random frames
   cangen can0 -I i -m -v -n 100 -g 10

2. Print received can frames

   candump can0

    

External links

https://www.can-cia.org/can-knowledge/

http://www.can-wiki.info/doku.php

https://elinux.org/CAN_Bus