华为IPv6-OSPFv3通信

一、配置思路
1、根据拓扑规划配置好IP地址。
2、全局运行OSPFV3通信
3、验证配置效果
二、PC与路由器配置IP地址
1、PC1配置地址如下

2、PC2配置地址如下

3、路由器配置地址如下

AR1
[AR1]ipv6 //全局下开启IPv6
[AR1-GigabitEthernet0/0/0]int g0/0/1
[AR1-GigabitEthernet0/0/0]ipv6 enable //进入接口后开启IPv6
[AR1-GigabitEthernet0/0/0]ipv6 address 1::254 64 //配置地址
[AR1-GigabitEthernet0/0/0]int g0/0/1
[AR1-GigabitEthernet0/0/1]ipv6 enable
[AR1-GigabitEthernet0/0/1]ipv6 address 12::1 64
[AR1]ospfv3 1 //进入ospfv3进程1
[AR1-ospfv3-1]router-id 1.1.1.1 //此路由ID为：1.1.1.1
[AR1-ospfv3-1]q //退出
[AR1]interface g0/0/0
[AR1-GigabitEthernet0/0/0]ospfv3 1 area 0 //在ospfv3进程1下将此接口宣告到区域0
[AR1-GigabitEthernet0/0/0]int g0/0/1
[AR1-GigabitEthernet0/0/1]ospfv3 1 area 0 ////在ospfv3进程1下将此接口宣告到区域0

AR2
[AR2]ipv6 //全局下开启IPv6
[AR2-GigabitEthernet0/0/1]int g0/0/1
[AR2-GigabitEthernet0/0/1]ipv6 enable //进入接口后开启IPv6
[AR2-GigabitEthernet0/0/1]ipv6 address 12::2 64 //配置地址
[AR2-GigabitEthernet0/0/1]int g0/0/2
[AR2-GigabitEthernet0/0/2]ipv6 enable
[AR2-GigabitEthernet0/0/2]ipv6 address 23::2 64
[AR2]ospfv3 1 //进入ospfv3进程1
[AR2-ospfv3-1]router-id 2.2.2.2 //此路由ID为：2.2.2.2
[AR2-ospfv3-1]q //退出
[AR2]interface g0/0/1
[AR2-GigabitEthernet0/0/1]ospfv3 1 area 0 //在ospfv3进程1下将此接口宣告到区域0
[AR2-GigabitEthernet0/0/2]int g0/0/2
[AR2-GigabitEthernet0/0/2]ospfv3 1 area 0 ////在ospfv3进程1下将此接口宣告到区域0

AR3
[AR3]ipv6 //全局下开启IPv6
[AR3-GigabitEthernet0/0/2]int g0/0/2
[AR3-GigabitEthernet0/0/2]ipv6 enable //进入接口后开启IPv6
[AR3-GigabitEthernet0/0/2]ipv6 address 23::3 64 //配置地址
[AR3-GigabitEthernet0/0/0]int g0/0/0
[AR3-GigabitEthernet0/0/0]ipv6 enable
[AR3-GigabitEthernet0/0/0]ipv6 address 3::254 64
[AR3]ospfv3 1 //进入ospfv3进程1
[AR3-ospfv3-1]router-id 3.3.3.3 //此路由ID为：3.3.3.3
[AR3-ospfv3-1]q //退出
[AR3]interface g0/0/1
[AR3-GigabitEthernet0/0/1]ospfv3 1 area 0 //在ospfv3进程1下将此接口宣告到区域0
[AR3-GigabitEthernet0/0/2]int g0/0/2
[AR3-GigabitEthernet0/0/2]ospfv3 1 area 0 ////在ospfv3进程1下将此接口宣告到区域0

三、验证结果

1、PC1可以Ping通PC2即可