Mercury MW305R v3.0 路由器改造 LEDE（OpenWRT）
说明
1. 改造 Mercury MW305R v3.0（芯片 9533）2. OpenWRT 版本：LEDE 17
3. 环境：Ubuntu 16.04 x64
第一步：修改硬件
1. 换 RAN 为 64M2. 换 flash 为 16M
注：本教程主要说明制作镜像部分，具体修改硬件步骤请参考：链接
第二步：获取源码
使用以下命令克隆我当时使用的版本源码：git clone -b lede-17.01 https://github.com/lede-project/source.git lede第三步：target profile 添加新路由器
修改文件：/target/linux/ar71xx/image/tp-link.mk添加以下内容：
define Device/mc-mw305r-v3
$(Device/tplink-16mlzma)
DEVICE_TITLE := MERCURY MC-MW305R v3
BOARDNAME := MC-MW305R-v3
TPLINK_HWID := 0x30500003
endef
TARGET_DEVICES += mc-mw305r-v3删除 /tmp 目录，使用以下命令配置：
make menuconfig在 Target System 里选择 Atheros AR7xxx/AR9xxx，然后在 Target Profile 里找到 MERCURY MC-MW305R v3 并选中。相关配置此时，编译一下，看看有没有错误。
makemake 成功后，/bin/targets/ar71xx/generic/ 目录下面会生成 MW305R 的 factory.bin，但是这时候下载到 flash 还不能启动，因为内核并没有支持 MW305R，继续下面的步骤。
第四步：kernel arch machine 新增路由器
新建文件：/build_dir/target-mips_24kc_musl/linux-ar71xx_generic/linux-4.4.74/arch/mips/ath79/mach-mc-mw305r-v3.c文件内容：
/*
* Mercury MW305R v3
*
* Copyright (C) 2014 Matthias Schiffer
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License version 2 as published
* by the Free Software Foundation.
*/
#include
#include
#include
#include
#include "common.h"
#include "dev-eth.h"
#include "dev-gpio-buttons.h"
#include "dev-leds-gpio.h"
#include "dev-m25p80.h"
#include "dev-wmac.h"
#include "machtypes.h"
#define MC_MW305RV3_GPIO_LED_WLAN 13
#define MC_MW305RV3_GPIO_LED_WAN 4
#define MC_MW305RV3_GPIO_LED_LAN4 11
#define MC_MW305RV3_GPIO_LED_LAN3 14
#define MC_MW305RV3_GPIO_LED_LAN2 15
#define MC_MW305RV3_GPIO_LED_LAN1 16
#define MC_MW305RV3_GPIO_BTN_RESET 12
#define MC_MW305RV3_GPIO_BTN_WIFI 17
#define MC_MW305RV3_KEYS_POLL_INTERVAL 20 /* msecs */
#define MC_MW305RV3_KEYS_DEBOUNCE_INTERVAL (3 * MC_MW305RV3_KEYS_POLL_INTERVAL)
static const char *mc_mw305r_v3_part_probes[] = {
"tp-link",
NULL,
};
static struct flash_platform_data mc_mw305r_v3_flash_data = {
.part_probes = mc_mw305r_v3_part_probes,
};
static struct gpio_led mc_mw305r_v3_leds_gpio[] __initdata = {
{
.name = "mercury:green:lan1",
.gpio = MC_MW305RV3_GPIO_LED_LAN1,
.active_low = 1,
}, {
.name = "mercury:green:lan2",
.gpio = MC_MW305RV3_GPIO_LED_LAN2,
.active_low = 1,
}, {
.name = "mercury:green:lan3",
.gpio = MC_MW305RV3_GPIO_LED_LAN3,
.active_low = 1,
}, {
.name = "mercury:green:lan4",
.gpio = MC_MW305RV3_GPIO_LED_LAN4,
.active_low = 1,
}, {
.name = "mercury:green:wan",
.gpio = MC_MW305RV3_GPIO_LED_WAN,
.active_low = 1,
}, {
.name = "mercury:green:wlan",
.gpio = MC_MW305RV3_GPIO_LED_WLAN,
.active_low = 1,
.default_trigger = "heartbeat",
},
};
static struct gpio_keys_button mc_mw305r_v3_gpio_keys[] __initdata = {
{
.desc = "Reset button",
.type = EV_KEY,
.code = KEY_RESTART,
.debounce_interval = MC_MW305RV3_KEYS_DEBOUNCE_INTERVAL,
.gpio = MC_MW305RV3_GPIO_BTN_RESET,
.active_low = 1,
}, {
.desc = "WIFI button",
.type = EV_KEY,
.code = KEY_RFKILL,
.debounce_interval = MC_MW305RV3_KEYS_DEBOUNCE_INTERVAL,
.gpio = MC_MW305RV3_GPIO_BTN_WIFI,
.active_low = 1,
}
};
static void __init tl_ap143_setup(void)
{
u8 *mac = (u8 *) KSEG1ADDR(0x1f01fc00);
u8 *ee = (u8 *) KSEG1ADDR(0x1fff1000);
u8 tmpmac[ETH_ALEN];
ath79_register_m25p80(&mc_mw305r_v3_flash_data);
ath79_setup_ar933x_phy4_switch(false, false);
ath79_register_mdio(0, 0x0);
/* LAN */
ath79_eth1_data.phy_if_mode = PHY_INTERFACE_MODE_GMII;
ath79_eth1_data.duplex = DUPLEX_FULL;
ath79_switch_data.phy_poll_mask |= BIT(4);
ath79_init_mac(ath79_eth1_data.mac_addr, mac, 0);
ath79_register_eth(1);
/* WAN */
ath79_switch_data.phy4_mii_en = 1;
ath79_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_MII;
ath79_eth0_data.duplex = DUPLEX_FULL;
ath79_eth0_data.speed = SPEED_100;
ath79_eth0_data.phy_mask = BIT(4);
ath79_init_mac(ath79_eth0_data.mac_addr, mac, 1);
ath79_register_eth(0);
ath79_init_mac(tmpmac, mac, 0);
ath79_register_wmac(ee, tmpmac);
}
static void __init mc_mw305r_v3_setup(void)
{
tl_ap143_setup();
ath79_gpio_output_select(3, AR934X_GPIO_OUT_GPIO);
ath79_gpio_output_select(4, AR934X_GPIO_OUT_GPIO);
ath79_gpio_output_select(11, AR934X_GPIO_OUT_GPIO);
ath79_gpio_output_select(14, AR934X_GPIO_OUT_GPIO);
ath79_gpio_output_select(15, AR934X_GPIO_OUT_GPIO);
ath79_gpio_output_select(16, AR934X_GPIO_OUT_GPIO);
ath79_register_leds_gpio(-1, ARRAY_SIZE(mc_mw305r_v3_leds_gpio),
mc_mw305r_v3_leds_gpio);
ath79_register_gpio_keys_polled(1, MC_MW305RV3_KEYS_POLL_INTERVAL,
ARRAY_SIZE(mc_mw305r_v3_gpio_keys),
mc_mw305r_v3_gpio_keys);
}
MIPS_MACHINE(ATH79_MACH_MW_MW305R, "MW-MW305R-v3", "MERCURY MW-MW305R v3",
mc_mw305r_v3_setup);
修改文件：/build_dir/target-mips_24kc_musl/linux-ar71xx_generic/linux-4.4.74/arch/mips/ath79/Kconfig
添加以下内容：
config ATH79_MACH_MC_MW305R
bool "MERCURY MC-MW305R v3 support"
select SOC_AR933X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
help
Say 'Y' here if you want your kernel to support the
MERCURY MC-MW305R v3.修改文件：/build_dir/target-mips_24kc_musl/linux-ar71xx_generic/linux-4.4.74/arch/mips/ath79/machtypes.h
添加以下内容：
ATH79_MACH_MC_MW305R,obj-$(CONFIG_ATH79_MACH_MC_MW305R) += mach-mc-mw305r-v3.o使用以下命令配置：
make kernel_menuconfig-> Machine selection
-> Atheros AR71XX/AR724X/AR913X machine selection
MERCURY MC-MW305R v3 support此时，编译一次看看有没有问题：
makemake 成功后，如果直接固件下载到 flash，已经能启动了，但会出现网络问题，继续看第五步。
第五步：network 配置问题（ar71xx系列）
修改文件：/target/linux/ar71xx/base-files/etc/board.d/02_network添加以下内容：
mc-mw305r-v3)
ucidef_set_interfaces_lan_wan "eth0" "eth1"
ucidef_add_switch "switch0" \
"0@eth0" "1:lan" "2:lan" "3:lan" "4:lan"
;;修改文件：/target/linux/ar71xx/base-files/lib/ar71xx.sh
添加以下内容：
*"MC-MW305R v3"*)
name="mc-mw305r-v3"
;;此时，再编译一次看看有没有问题：
makemake 成功后，如果下载固件到 flash，网络已经没问题了，但是会发现 LED 灯工作得不正常，继续看第六步。
第六步：LED 灯问题
修改文件：/target/linux/ar71xx/base-files/etc/board.d/01_leds添加以下内容：
mc-mw305r-v3)
ucidef_set_led_netdev "wan" "WAN" "mercury:green:wan" "eth1"
ucidef_set_led_switch "lan0" "LAN0" "mercury:green:lan1" "switch0" "0x10"
ucidef_set_led_switch "lan1" "LAN1" "mercury:green:lan2" "switch0" "0x08"
ucidef_set_led_switch "lan2" "LAN2" "mercury:green:lan3" "switch0" "0x04"
ucidef_set_led_switch "lan3" "LAN3" "mercury:green:lan4" "switch0" "0x02"
ucidef_set_led_wlan "wlan" "WLAN" "mercury:green:wlan" "phy0tpt"
;;这时候已经大功告成了，最后编译一次：
make