【u-boot-2016到s5pv210】2.2 uboot内存规划

【u-boot-2016到s5pv210】2.2 uboot内存规划

1 主要流程

2 关键点

static init_fnc_t init_sequence_f[] = {
#ifdef CONFIG_SANDBOX
	setup_ram_buf,
#endif
	setup_mon_len,
#ifdef CONFIG_OF_CONTROL
	fdtdec_setup,
#endif
#ifdef CONFIG_TRACE
	trace_early_init,
#endif
	initf_malloc,
	initf_console_record,
#if defined(CONFIG_MPC85xx) || defined(CONFIG_MPC86xx)
	/* TODO: can this go into arch_cpu_init()? */
	probecpu,
#endif
#if defined(CONFIG_X86) && defined(CONFIG_HAVE_FSP)
	x86_fsp_init,
#endif
	arch_cpu_init,		/* basic arch cpu dependent setup */
	mach_cpu_init,		/* SoC/machine dependent CPU setup */
	initf_dm,
	arch_cpu_init_dm,
	mark_bootstage,		/* need timer, go after init dm */
#if defined(CONFIG_BOARD_EARLY_INIT_F)
	board_early_init_f,
#endif
	/* TODO: can any of this go into arch_cpu_init()? */
#if defined(CONFIG_PPC) && !defined(CONFIG_8xx_CPUCLK_DEFAULT)
	get_clocks,		/* get CPU and bus clocks (etc.) */
#if defined(CONFIG_TQM8xxL) && !defined(CONFIG_TQM866M) \
		&& !defined(CONFIG_TQM885D)
	adjust_sdram_tbs_8xx,
#endif
	/* TODO: can we rename this to timer_init()? */
	init_timebase,
#endif
#if defined(CONFIG_ARM) || defined(CONFIG_MIPS) || \
		defined(CONFIG_BLACKFIN) || defined(CONFIG_NDS32) || \
		defined(CONFIG_SPARC)
	timer_init,		/* initialize timer */
#endif
#ifdef CONFIG_SYS_ALLOC_DPRAM
#if !defined(CONFIG_CPM2)
	dpram_init,
#endif
#endif
#if defined(CONFIG_BOARD_POSTCLK_INIT)
	board_postclk_init,
#endif
#if defined(CONFIG_SYS_FSL_CLK) || defined(CONFIG_M68K)
	get_clocks,
#endif
	env_init,		/* initialize environment */
#if defined(CONFIG_8xx_CPUCLK_DEFAULT)
	/* get CPU and bus clocks according to the environment variable */
	get_clocks_866,
	/* adjust sdram refresh rate according to the new clock */
	sdram_adjust_866,
	init_timebase,
#endif
	init_baud_rate,		/* initialze baudrate settings */
	serial_init,		/* serial communications setup */
	console_init_f,		/* stage 1 init of console */
#ifdef CONFIG_SANDBOX
	sandbox_early_getopt_check,
#endif
	display_options,	/* say that we are here */
	display_text_info,	/* show debugging info if required */
#if defined(CONFIG_MPC8260)
	prt_8260_rsr,
	prt_8260_clks,
#endif /* CONFIG_MPC8260 */
#if defined(CONFIG_MPC83xx)
	prt_83xx_rsr,
#endif
#if defined(CONFIG_PPC) || defined(CONFIG_M68K)
	checkcpu,
#endif
	print_cpuinfo,		/* display cpu info (and speed) */
#if defined(CONFIG_MPC5xxx)
	prt_mpc5xxx_clks,
#endif /* CONFIG_MPC5xxx */
#if defined(CONFIG_DISPLAY_BOARDINFO)
	show_board_info,
#endif
	INIT_FUNC_WATCHDOG_INIT
#if defined(CONFIG_MISC_INIT_F)
	misc_init_f,
#endif
	INIT_FUNC_WATCHDOG_RESET
#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C)
	init_func_i2c,
#endif
#if defined(CONFIG_HARD_SPI)
	init_func_spi,
#endif
	announce_dram_init,
	/* TODO: unify all these dram functions? */
#if defined(CONFIG_ARM) || defined(CONFIG_X86) || defined(CONFIG_NDS32) || \
		defined(CONFIG_MICROBLAZE) || defined(CONFIG_AVR32)
	dram_init,		/* configure available RAM banks */
#endif
#if defined(CONFIG_MIPS) || defined(CONFIG_PPC) || defined(CONFIG_M68K)
	init_func_ram,
#endif
#ifdef CONFIG_POST
	post_init_f,
#endif
	INIT_FUNC_WATCHDOG_RESET
#if defined(CONFIG_SYS_DRAM_TEST)
	testdram,
#endif /* CONFIG_SYS_DRAM_TEST */
	INIT_FUNC_WATCHDOG_RESET

#ifdef CONFIG_POST
	init_post,
#endif
	INIT_FUNC_WATCHDOG_RESET
	/*
	 * Now that we have DRAM mapped and working, we can
	 * relocate the code and continue running from DRAM.
	 *
	 * Reserve memory at end of RAM for (top down in that order):
	 *  - area that won't get touched by U-Boot and Linux (optional)
	 *  - kernel log buffer
	 *  - protected RAM
	 *  - LCD framebuffer
	 *  - monitor code
	 *  - board info struct
	 */
	setup_dest_addr,
#if defined(CONFIG_BLACKFIN) || defined(CONFIG_XTENSA)
	/* Blackfin u-boot monitor should be on top of the ram */
	reserve_uboot,
#endif
#if defined(CONFIG_SPARC)
	reserve_prom,
#endif
#if defined(CONFIG_LOGBUFFER) && !defined(CONFIG_ALT_LB_ADDR)
	reserve_logbuffer,
#endif
#ifdef CONFIG_PRAM
	reserve_pram,
#endif
	reserve_round_4k,
#if !(defined(CONFIG_SYS_ICACHE_OFF) && defined(CONFIG_SYS_DCACHE_OFF)) && \
		defined(CONFIG_ARM)
	reserve_mmu,
#endif
#ifdef CONFIG_DM_VIDEO
	reserve_video,
#else
# ifdef CONFIG_LCD
	reserve_lcd,
# endif
	/* TODO: Why the dependency on CONFIG_8xx? */
# if defined(CONFIG_VIDEO) && (!defined(CONFIG_PPC) || defined(CONFIG_8xx)) && \
		!defined(CONFIG_ARM) && !defined(CONFIG_X86) && \
		!defined(CONFIG_BLACKFIN) && !defined(CONFIG_M68K)
	reserve_legacy_video,
# endif
#endif /* CONFIG_DM_VIDEO */
	reserve_trace,
#if !defined(CONFIG_BLACKFIN) && !defined(CONFIG_XTENSA)
	reserve_uboot,
#endif
#ifndef CONFIG_SPL_BUILD
	reserve_malloc,
	reserve_board,
#endif
	setup_machine,
	reserve_global_data,
	reserve_fdt,
	reserve_arch,
	reserve_stacks,
	setup_dram_config,
	show_dram_config,
#if defined(CONFIG_PPC) || defined(CONFIG_M68K) || defined(CONFIG_MIPS)
	setup_board_part1,
#endif
#if defined(CONFIG_PPC) || defined(CONFIG_M68K)
	INIT_FUNC_WATCHDOG_RESET
	setup_board_part2,
#endif
	display_new_sp,
#ifdef CONFIG_SYS_EXTBDINFO
	setup_board_extra,
#endif
	INIT_FUNC_WATCHDOG_RESET
	reloc_fdt,
	setup_reloc,
#if defined(CONFIG_X86) || defined(CONFIG_ARC)
	copy_uboot_to_ram,
	clear_bss,
	do_elf_reloc_fixups,
#endif
#if defined(CONFIG_XTENSA)
	clear_bss,
#endif
#if !defined(CONFIG_ARM) && !defined(CONFIG_SANDBOX)
	jump_to_copy,
#endif
	NULL,
};