STM32 USBHID应用

    关于USB接口不多说了，你可以到网络上搜索很多的。我这里只是说说STM32的应用，具体USB的东西 不多说。

    我在设计STM32程序的时候，如果需要和上位机通信，一般来说串口，485啊，或者CAN，也可以USB ，或者网络通信，下面具体说说USB通信，正点原子的开发板提供了一些关于USB接口的使用例程，如果 你将那个例程看懂的话，自己移植一个关于HID或者虚拟串口，甚至自己写一个固件，设计自己的驱动， 自己的VC应用都行，后者比较麻烦，对初学者估计很难。所以我就选择了移植HID，因为这个HID驱动在 xp系统下是集成的，不需要我们去些驱动程序，我们只需要写好固件，和应用程序（VC6.0）就好了。

   下面就从固件程序开始说起，固件程序就是需要下载到STM32FLASH中的程序，我是开发环境是 IAR5.30，因为中间涉及到很多东西，我简略说一下，USBSTM32库文件版本是3.3.0，其他外设STM32库文件时3.5.0.

USBHID组下的文件就是需要我们修改的文件，是针对HID的。

1，修改usb_desc.c文件，主要是设备描述符一些东西,网络上有相关例程可以参考

点击(此处)折叠或打开

#include "usb_lib.h"
#include "usb_desc.h"
const u8 CustomHID_DeviceDescriptor[CUSTOMHID_SIZ_DEVICE_DESC] =
  {
    0x12,  /*bLength */
    USB_DEVICE_DESCRIPTOR_TYPE, /*bDescriptorType*/
    0x00,  /*bcdUSB */
    0x02,
    0x00,  /*bDeviceClass*/
    0x00,  /*bDeviceSubClass*/
    0x00,  /*bDeviceProtocol*/
    0x40,  /*bMaxPacketSize40*/
    0x83,  /*idVendor (0x0483)*/
    0x04,
    0x50,  /*idProduct = 0x5750*/
    0x57,
    0x00,  /*bcdDevice rel. 2.00*/
    0x02,
    1,  /*Index of string descriptor describing
                                              manufacturer */
    2,  /*Index of string descriptor describing
                                             product*/
    3,  /*Index of string descriptor describing the
                                             device serial number */
    0x01  /*bNumConfigurations*/
  }
  ; /* CustomHID_DeviceDescriptor */


/* USB Configuration Descriptor */
/* All Descriptors (Configuration, Interface, Endpoint, Class, Vendor */
const u8 CustomHID_ConfigDescriptor[CUSTOMHID_SIZ_CONFIG_DESC] =
  {
    0x09, /* bLength: Configuation Descriptor size */
    USB_CONFIGURATION_DESCRIPTOR_TYPE, /* bDescriptorType: Configuration */
    CUSTOMHID_SIZ_CONFIG_DESC,
    /* wTotalLength: Bytes returned */
    0x00,
    0x01,  /* bNumInterfaces: 1 interface */
    0x01,  /* bConfigurationValue: Configuration value */
    0x00,  /* iConfiguration: Index of string descriptor describing
                                 the configuration*/
    0xC0,  /* bmAttributes: Bus powered */
    0x32,  /* MaxPower 100 mA: this current is used for detecting Vbus */

    /************** Descriptor of Custom HID interface ****************/
    /* 09 */
    0x09,  /* bLength: Interface Descriptor size */
    USB_INTERFACE_DESCRIPTOR_TYPE,/* bDescriptorType: Interface descriptor type */
    0x00,  /* bInterfaceNumber: Number of Interface */
    0x00,  /* bAlternateSetting: Alternate setting */
    0x02,  /* bNumEndpoints */
    0x03,  /* bInterfaceClass: HID */
    0x00,  /* bInterfaceSubClass : 1=BOOT, 0=no boot */
    0x00,  /* nInterfaceProtocol : 0=none, 1=keyboard, 2=mouse */
    0,  /* iInterface: Index of string descriptor */
    /******************** Descriptor of Custom HID HID ********************/
    /* 18 */
    0x09,  /* bLength: HID Descriptor size */
    HID_DESCRIPTOR_TYPE, /* bDescriptorType: HID */
    0x10,  /* bcdHID: HID Class Spec release number */
    0x01,
    0x00,  /* bCountryCode: Hardware target country */
    0x01,  /* bNumDescriptors: Number of HID class descriptors to follow */
    0x22,  /* bDescriptorType */
    CUSTOMHID_SIZ_REPORT_DESC,/* wItemLength: Total length of Report descriptor */
    0x00,
    /******************** Descriptor of Custom HID endpoints ******************/
    /* 27 */
    0x07,  /* bLength: Endpoint Descriptor size */
    USB_ENDPOINT_DESCRIPTOR_TYPE, /* bDescriptorType: */

    0x81,  /* bEndpointAddress: Endpoint Address (IN) */
    0x03,  /* bmAttributes: Interrupt endpoint */
    0x40,  /* wMaxPacketSize: 64 Bytes max */
    0x00,
    0x20,  /* bInterval: Polling Interval (32 ms) */
    /* 34 */

    0x07,    /* bLength: Endpoint Descriptor size */
    USB_ENDPOINT_DESCRIPTOR_TYPE,    /* bDescriptorType: */
            /*    Endpoint descriptor type */
    0x01,    /* bEndpointAddress: */
            /*    Endpoint Address (OUT) */
    0x03,    /* bmAttributes: Interrupt endpoint */
    0x40,    /* wMaxPacketSize: 64 Bytes max  */
    0x00,
    0x20,    /* bInterval: Polling Interval (20 ms) */
    /* 41 */
  }
  ; /* CustomHID_ConfigDescriptor */
const u8 CustomHID_ReportDescriptor[CUSTOMHID_SIZ_REPORT_DESC] =
  {
    0x05, 0xFF,  // USAGE_PAGE(User define)
    0x09, 0xFF,  // USAGE(User define)
    0xa1, 0x01,  // COLLECTION (Application)
    0x05, 0x01,  // USAGE_PAGE(1)
    0x19, 0x00,  // USAGE_MINIMUM(0)
    0x29, 0xFF,  // USAGE_MAXIMUM(255)
    0x15, 0x00,  // LOGICAL_MINIMUM (0)
    0x25, 0xFF,  // LOGICAL_MAXIMUM (255)
    0x75, 0x08,  // REPORT_SIZE (8)
    0x95, 0x40,  // REPORT_COUNT (64)
    0x81, 0x02,  // INPUT (Data,Var,Abs)
    0x05, 0x02,  // USAGE_PAGE(2)
    0x19, 0x00,  // USAGE_MINIMUM (0)
    0x29, 0xFF,  // USAGE_MAXIMUM (255)
    0x15, 0x00,  // LOGICAL_MINIMUM (0)
    0x25, 0xFF,  // LOGICAL_MAXIMUM (255)
    0x95, 0x08,  // REPORT_COUNT (8)
    0x75, 0x40,  // REPORT_SIZE (64)
    0x91, 0x02,  // OUTPUT (Data,Var,Abs)
    0xc0  // END_COLLECTION
  }; /* ReportDescriptor */

/* USB String Descriptors (optional) */
const u8 CustomHID_StringLangID[CUSTOMHID_SIZ_STRING_LANGID] =
  {
    CUSTOMHID_SIZ_STRING_LANGID,
    USB_STRING_DESCRIPTOR_TYPE,
    0x09,
    0x04
  }
  ; /* LangID = 0x0409: U.S. English */

const u8 CustomHID_StringVendor[CUSTOMHID_SIZ_STRING_VENDOR] =
  {
    CUSTOMHID_SIZ_STRING_VENDOR, /* Size of Vendor string */
    USB_STRING_DESCRIPTOR_TYPE,  /* bDescriptorType*/
    0xd8, 0x98, //
    0x6c, 0x62, //
    0xe5, 0x5d, //¤
    0x5c, 0x4f, //×÷
    0xa4, 0x5b, //
    0x68, 0x00, //h
    0x74, 0x00, //t
    0x74, 0x00, //t
    0x70, 0x00, //p
    0x3a, 0x00, //:
    0x2f, 0x00, ///
    0x2f, 0x00, ///
    0x62, 0x00, //b
    0x6c, 0x00, //l
    0x6f, 0x00, //o
    0x67, 0x00, //g
    0x2e, 0x00, //.
    0x63, 0x00, //c
    0x73, 0x00, //s
    0x64, 0x00, //d
    0x6e, 0x00, //n
    0x2e, 0x00, //.
    0x6e, 0x00, //n
    0x65, 0x00, //e
    0x74, 0x00, //t
    0x2f, 0x00, ///
    0x63, 0x00, //c
    0x79, 0x00, //y
    0x37, 0x00, //7
    0x35, 0x00, //5
    0x37, 0x00, //7

  };

const u8 CustomHID_StringProduct[CUSTOMHID_SIZ_STRING_PRODUCT] =
  {
    CUSTOMHID_SIZ_STRING_PRODUCT,  /* bLength */
    USB_STRING_DESCRIPTOR_TYPE,  /* bDescriptorType */
    0xea, 0x81, //×
    0x9a, 0x5b, //¨
    0x49, 0x4e, //
    0x84, 0x76, //
    0x55, 0x00, //U
    0x53, 0x00, //S
    0x42, 0x00, //B
    0x20, 0x00, //
    0x48, 0x00, //H
    0x49, 0x00, //I
    0x44, 0x00, //D
    0xbe, 0x8b, //è
    0x07, 0x59, //±

  };
u8 CustomHID_StringSerial[CUSTOMHID_SIZ_STRING_SERIAL] =
  {
    CUSTOMHID_SIZ_STRING_SERIAL,  /* bLength */
    USB_STRING_DESCRIPTOR_TYPE,  /* bDescriptorType */
    'S', 0, 'T', 0, 'M', 0,'3', 0,'2', 0, '1', 0, '0', 0
  };

/******************* (C) COPYRIGHT 2008 STMicroelectronics *****END OF FILE****/

2，修改usb_prop.c文件，主要是CustomHID_Reset(void)函数，主要是设置端口0，端口1的发送地址和 接收地址。

点击(此处)折叠或打开

#include "usb_lib.h"
#include "usb_conf.h"
#include "usb_prop.h"
#include "usb_desc.h"
#include "usb_pwr.h"
#include "usb_hw.h"

//static uint8_t s_Request = 0;

/******************** (C) COPYRIGHT 2008 STMicroelectronics ********************
* File Name  : usb_prop.c
* Author  : MCD Application Team
* Version  : V2.2.0
* Date  : 06/13/2008
* Description  : All processings related to Custom HID Demo
********************************************************************************
* THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
* WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE TIME.
* AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY DIRECT,
* INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING FROM THE
* CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE CODING
* INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
*******************************************************************************/

/* Includes ------------------------------------------------------------------*/






/* Private typedef -----------------------------------------------------------*/
/* Private define ------------------------------------------------------------*/
/* Private macro -------------------------------------------------------------*/
/* Private variables ---------------------------------------------------------*/
u32 ProtocolValue;

/* -------------------------------------------------------------------------- */
/* Structures initializations */
/* -------------------------------------------------------------------------- */

DEVICE Device_Table =
  {
    EP_NUM,
    1
  };

DEVICE_PROP Device_Property =
  {
    CustomHID_init,
    CustomHID_Reset,
    CustomHID_Status_In,
    CustomHID_Status_Out,
    CustomHID_Data_Setup,
    CustomHID_NoData_Setup,
    CustomHID_Get_Interface_Setting,
    CustomHID_GetDeviceDescriptor,
    CustomHID_GetConfigDescriptor,
    CustomHID_GetStringDescriptor,
    0,
    0x40 /*MAX PACKET SIZE*/
  };
USER_STANDARD_REQUESTS User_Standard_Requests =
  {
    CustomHID_GetConfiguration,
    CustomHID_SetConfiguration,
    CustomHID_GetInterface,
    CustomHID_SetInterface,
    CustomHID_GetStatus,
    CustomHID_ClearFeature,
    CustomHID_SetEndPointFeature,
    CustomHID_SetDeviceFeature,
    CustomHID_SetDeviceAddress
  };

ONE_DESCRIPTOR Device_Descriptor =
  {
    (u8*)CustomHID_DeviceDescriptor,
    CUSTOMHID_SIZ_DEVICE_DESC
  };

ONE_DESCRIPTOR Config_Descriptor =
  {
    (u8*)CustomHID_ConfigDescriptor,
    CUSTOMHID_SIZ_CONFIG_DESC
  };

ONE_DESCRIPTOR CustomHID_Report_Descriptor =
  {
    (u8 *)CustomHID_ReportDescriptor,
    CUSTOMHID_SIZ_REPORT_DESC
  };

ONE_DESCRIPTOR CustomHID_Hid_Descriptor =
  {
    (u8*)CustomHID_ConfigDescriptor + CUSTOMHID_OFF_HID_DESC,
    CUSTOMHID_SIZ_HID_DESC
  };

ONE_DESCRIPTOR String_Descriptor[4] =
  {
    {(u8*)CustomHID_StringLangID, CUSTOMHID_SIZ_STRING_LANGID},
    {(u8*)CustomHID_StringVendor, CUSTOMHID_SIZ_STRING_VENDOR},
    {(u8*)CustomHID_StringProduct, CUSTOMHID_SIZ_STRING_PRODUCT},
    {(u8*)CustomHID_StringSerial, CUSTOMHID_SIZ_STRING_SERIAL}
  };

/* Extern variables ----------------------------------------------------------*/
/* Private function prototypes -----------------------------------------------*/
/* Extern function prototypes ------------------------------------------------*/
/* Private functions ---------------------------------------------------------*/

/*******************************************************************************
* Function Name  : CustomHID_init.
* Description  : Custom HID init routine.
* Input  : None.
* Output  : None.
* Return  : None.
*******************************************************************************/
void CustomHID_init(void)
{
  /* Update the serial number string descriptor with the data from the unique
  ID*/
// Get_SerialNum();

  pInformation->Current_Configuration = 0;
  /* Connect the device */
  //PowerOn();
  usb_PowerOn();
  /* USB interrupts initialization */
  _SetISTR(0);  /* clear pending interrupts */
  wInterrupt_Mask = IMR_MSK;
  _SetCNTR(wInterrupt_Mask); /* set interrupts mask */

  bDeviceState = UNCONNECTED;
}

/*******************************************************************************
* Function Name  : CustomHID_Reset.
* Description  : Custom HID reset routine.
* Input  : None.
* Output  : None.
* Return  : None.
*******************************************************************************/
void CustomHID_Reset(void)
{
  /* Set Joystick_DEVICE as not configured */
  pInformation->Current_Configuration = 0;
  pInformation->Current_Interface = 0;/*the default Interface*/

  pInformation->Current_Feature = CustomHID_ConfigDescriptor[7];

   SetBTABLE(BTABLE_ADDRESS);
  /* Initialize Endpoint 0 */
  SetEPType(ENDP0, EP_CONTROL);
  SetEPTxStatus(ENDP0, EP_TX_STALL);
  SetEPRxAddr(ENDP0, ENDP0_RXADDR);
  SetEPTxAddr(ENDP0, ENDP0_TXADDR);
  Clear_Status_Out(ENDP0);
  SetEPRxCount(ENDP0, Device_Property.MaxPacketSize);
  SetEPRxValid(ENDP0);

  /* Initialize Endpoint 1 */
  SetEPType(ENDP1, EP_INTERRUPT);
  SetEPTxAddr(ENDP1, ENDP1_TXADDR);
  SetEPTxCount(ENDP1, 64);
  SetEPRxStatus(ENDP1, EP_RX_DIS);
  SetEPTxStatus(ENDP1, EP_TX_NAK);

  /* Initialize Endpoint 1 */
 // SetEPType(ENDP1, EP_INTERRUPT);
  SetEPRxAddr(ENDP1, ENDP1_RXADDR);
  SetEPRxCount(ENDP1, 64);
 // SetEPTxStatus(ENDP1, EP_TX_DIS);
  SetEPRxStatus(ENDP1, EP_RX_VALID);
   bDeviceState = ATTACHED;
  /* Set this device to response on default address */
  SetDeviceAddress(0);
}
/*******************************************************************************
* Function Name  : CustomHID_SetConfiguration.
* Description  : Udpade the device state to configured and command the ADC
* conversion.
* Input  : None.
* Output  : None.
* Return  : None.
*******************************************************************************/
void CustomHID_SetConfiguration(void)
{
  if (pInformation->Current_Configuration != 0)
  {
    /* Device configured */
    bDeviceState = CONFIGURED;

    /* Start ADC1 Software Conversion */
    ADC_SoftwareStartConvCmd(ADC1, ENABLE);
  }
}
/*******************************************************************************
* Function Name  : CustomHID_SetConfiguration.
* Description  : Udpade the device state to addressed.
* Input  : None.
* Output  : None.
* Return  : None.
*******************************************************************************/
void CustomHID_SetDeviceAddress (void)
{
  bDeviceState = ADDRESSED;
}
/*******************************************************************************
* Function Name  : CustomHID_Status_In.
* Description  : Joystick status IN routine.
* Input  : None.
* Output  : None.
* Return  : None.
*******************************************************************************/
void CustomHID_Status_In(void)
{
}

/*******************************************************************************
* Function Name  : CustomHID_Status_Out
* Description  : Joystick status OUT routine.
* Input  : None.
* Output  : None.
* Return  : None.
*******************************************************************************/
void CustomHID_Status_Out (void)
{
}

/*******************************************************************************
* Function Name  : CustomHID_Data_Setup
* Description  : Handle the data class specific requests.
* Input  : Request Nb.
* Output  : None.
* Return  : USB_UNSUPPORT or USB_SUCCESS.
*******************************************************************************/
RESULT CustomHID_Data_Setup(u8 RequestNo)
{
  u8 *(*CopyRoutine)(u16);

  CopyRoutine = NULL;

  if ((RequestNo == GET_DESCRIPTOR)
      && (Type_Recipient == (STANDARD_REQUEST | INTERFACE_RECIPIENT))
      && (pInformation->USBwIndex0 == 0))
  {

    if (pInformation->USBwValue1 == REPORT_DESCRIPTOR)
    {
      CopyRoutine = CustomHID_GetReportDescriptor;
    }
    else if (pInformation->USBwValue1 == HID_DESCRIPTOR_TYPE)
    {
      CopyRoutine = CustomHID_GetHIDDescriptor;
    }

  } /* End of GET_DESCRIPTOR */

  /*** GET_PROTOCOL ***/
  else if ((Type_Recipient == (CLASS_REQUEST | INTERFACE_RECIPIENT))
           && RequestNo == GET_PROTOCOL)
  {
    CopyRoutine = CustomHID_GetProtocolValue;
  }

  if (CopyRoutine == NULL)
  {
    return USB_UNSUPPORT;
  }

  pInformation->Ctrl_Info.CopyData = CopyRoutine;
  pInformation->Ctrl_Info.Usb_wOffset = 0;
  (*CopyRoutine)(0);
  return USB_SUCCESS;
}

/*******************************************************************************
* Function Name  : CustomHID_NoData_Setup
* Description  : handle the no data class specific requests
* Input  : Request Nb.
* Output  : None.
* Return  : USB_UNSUPPORT or USB_SUCCESS.
*******************************************************************************/
RESULT CustomHID_NoData_Setup(u8 RequestNo)
{
  if ((Type_Recipient == (CLASS_REQUEST | INTERFACE_RECIPIENT))
      && (RequestNo == SET_PROTOCOL))
  {
    return CustomHID_SetProtocol();
  }

  else
  {
    return USB_UNSUPPORT;
  }
}

/*******************************************************************************
* Function Name  : CustomHID_GetDeviceDescriptor.
* Description  : Gets the device descriptor.
* Input  : Length
* Output  : None.
* Return  : The address of the device descriptor.
*******************************************************************************/
u8 *CustomHID_GetDeviceDescriptor(u16 Length)
{
  return Standard_GetDescriptorData(Length, &Device_Descriptor);
}

/*******************************************************************************
* Function Name  : CustomHID_GetConfigDescriptor.
* Description  : Gets the configuration descriptor.
* Input  : Length
* Output  : None.
* Return  : The address of the configuration descriptor.
*******************************************************************************/
u8 *CustomHID_GetConfigDescriptor(u16 Length)
{
  return Standard_GetDescriptorData(Length, &Config_Descriptor);
}

/*******************************************************************************
* Function Name  : CustomHID_GetStringDescriptor
* Description  : Gets the string descriptors according to the needed index
* Input  : Length
* Output  : None.
* Return  : The address of the string descriptors.
*******************************************************************************/
u8 *CustomHID_GetStringDescriptor(u16 Length)
{
  u8 wValue0 = pInformation->USBwValue0;
  if (wValue0 > 4)
  {
    return NULL;
  }
  else
  {
    return Standard_GetDescriptorData(Length, &String_Descriptor[wValue0]);
  }
}

/*******************************************************************************
* Function Name  : CustomHID_GetReportDescriptor.
* Description  : Gets the HID report descriptor.
* Input  : Length
* Output  : None.
* Return  : The address of the configuration descriptor.
*******************************************************************************/
u8 *CustomHID_GetReportDescriptor(u16 Length)
{
  return Standard_GetDescriptorData(Length, &CustomHID_Report_Descriptor);
}

/*******************************************************************************
* Function Name  : CustomHID_GetHIDDescriptor.
* Description  : Gets the HID descriptor.
* Input  : Length
* Output  : None.
* Return  : The address of the configuration descriptor.
*******************************************************************************/
u8 *CustomHID_GetHIDDescriptor(u16 Length)
{
  return Standard_GetDescriptorData(Length, &CustomHID_Hid_Descriptor);
}

/*******************************************************************************
* Function Name  : CustomHID_Get_Interface_Setting.
* Description  : tests the interface and the alternate setting according to the
* supported one.
* Input  : - Interface : interface number.
*  - AlternateSetting : Alternate Setting number.
* Output  : None.
* Return  : USB_SUCCESS or USB_UNSUPPORT.
*******************************************************************************/
RESULT CustomHID_Get_Interface_Setting(u8 Interface, u8 AlternateSetting)
{
  if (AlternateSetting > 0)
  {
    return USB_UNSUPPORT;
  }
  else if (Interface > 0)
  {
    return USB_UNSUPPORT;
  }
  return USB_SUCCESS;
}

/*******************************************************************************
* Function Name  : CustomHID_SetProtocol
* Description  : Joystick Set Protocol request routine.
* Input  : None.
* Output  : None.
* Return  : USB SUCCESS.
*******************************************************************************/
RESULT CustomHID_SetProtocol(void)
{
  u8 wValue0 = pInformation->USBwValue0;
  ProtocolValue = wValue0;
  return USB_SUCCESS;
}

/*******************************************************************************
* Function Name  : CustomHID_GetProtocolValue
* Description  : get the protocol value
* Input  : Length.
* Output  : None.
* Return  : address of the protcol value.
*******************************************************************************/
u8 *CustomHID_GetProtocolValue(u16 Length)
{
  if (Length == 0)
  {
    pInformation->Ctrl_Info.Usb_wLength = 1;
    return NULL;
  }
  else
  {
    return (u8 *)(&ProtocolValue);
  }
}

/******************* (C) COPYRIGHT 2008 STMicroelectronics *****END OF FILE****/

3，修改usb_endp.c文件，这是端口接收数据函数。

点击(此处)折叠或打开

#include "usb_lib.h"
#include "usb_desc.h"
#include "usb_mem.h"
#include "usb_hw.h"
#include "usb_istr.h"
#include "usb_pwr.h"

/* Interval between sending IN packets in frame number (1 frame = 1ms) */
/*#define VCOMPORT_IN_FRAME_INTERVAL 5

extern uint8_t USART_Rx_Buffer[];
extern uint32_t USART_Rx_ptr_out;
extern uint32_t USART_Rx_length;
extern uint8_t USB_Tx_State;*/
u8 Receive_Buffer[64];
/*
*********************************************************************************************************
*      : EP1_IN_Callback
*    ÷: 1 IN°ü¨è±->PC÷
*      :
*    ·  :
*********************************************************************************************************
u8 Receive_Buffer[64];

/* Private function prototypes -----------------------------------------------*/
/* Private functions ---------------------------------------------------------*/
/*******************************************************************************
* Function Name  : EP1_OUT_Callback.
* Description  : EP1 OUT Callback Routine.
* Input  : None.
* Output  : None.
* Return  : None.
*******************************************************************************/
void EP1_OUT_Callback(void)
{
    /*u8 DataLen;
    DataLen = GetEPRxCount(ENDP1);
    PMAToUserBufferCopy(Receive_Buffer, ENDP1_RXADDR, DataLen);
    SetEPRxValid(ENDP1);*/
  u8 DataLen;
  DataLen = GetEPRxCount(ENDP1);
  PMAToUserBufferCopy(Receive_Buffer, ENDP1_RXADDR, DataLen);
  SetEPRxValid(ENDP1);

  UserToPMABufferCopy(Receive_Buffer, GetEPTxAddr(ENDP1), DataLen);
  SetEPTxCount(ENDP1, DataLen);
  SetEPTxValid(ENDP1);

}
/*
*********************************************************************************************************
*      : EP3_OUT_Callback
*    ÷: 3 OUT°ü¨PC->è±÷
*      :
*    ·  :
*********************************************************************************************************
*/
/*void EP3_OUT_Callback(void)
{
    uint16_t usRxCnt;
    //uint8_t USB_Rx_Buffer[VIRTUAL_COM_PORT_DATA_SIZE];

    /* USB3USB_Rx_Buffer ó±USB_Rx_Cnt */
    //usRxCnt = USB_SIL_Read(EP3_OUT, USB_Rx_Buffer);

    /*  */
    //usb_SaveHostDataToBuf(USB_Rx_Buffer, usRxCnt);

    /* í EP3  */
    //SetEPRxValid(ENDP3);
//}

/*
*********************************************************************************************************
*      : SOF_Callback
*    ÷: SOF÷  .SOFhostframe·
*      :
*    ·  :
*********************************************************************************************************
*/
/*void SOF_Callback(void)
{
    static uint32_t FrameCount = 0;

    if (bDeviceState == CONFIGURED)
    {
        if (FrameCount++ == VCOMPORT_IN_FRAME_INTERVAL)
        {
            /* Reset the frame counter */
            //FrameCount = 0;

            /* Check the data to be sent through IN pipe */
            //EP1_IN_Callback();
            //Handle_USBAsynchXfer();
        //}
    //}
//}

   修改这个函数之后，编译时会提示重定义NOP_Process，这个问题的解决办法是：在usb_config.h中 找到这样一句：

#define  EP1_OUT_Callback  NOP_Process，

将这一句注释掉，使得EP1接受函数不是空进程了，程序就运行成功了。

   还有就是我在这里遇见了no define ADC_SoftStartConvertCmd()这样的错误，你看看你的ST库函数

里面将ADC的库添加没有，添加以后，错误消失。

   接下来就是应用程序了，我利用了百合电子工作室的VC6.0例程，修改了一下，VID和PID，然后添加 几个按钮来控制发送数据。

驱动程序加载成功，

发送数据到EP1，然后STM32利用EP1将数据返回。

我将从USB接受到的64字节数据在LCD显示出来了，看图片，那个绿色的LED就是上面软件LEDON和LEDoff按钮控制的。

下面给2个链接，可以参考一下，我就是参考他们的代码移植成功的。在此也表示感谢。

附件是hex文件，在正点原子战舰开发板验证过，没有问题。bushound50是调试USB常用的软件。

http://blog.csdn.net/taot2009/article/details/7363091 

http://www.baiheee.com/OpenSource/Easy%20USB%2051%20Programer/Easy%20USB%2051%20Programer9.htm

 Project.rar     bushound50.rar   

from: http://blog.chinaunix.net/uid-24343357-id-3431635.html?/12365.html