华为做链路捆绑

一.拓扑图。

华为做链路捆绑_第1张图片

二.实验要求。

1.pc间互通。

2.用链路捆绑做二层和二层互绑,二层和三层互绑,三层和三层互绑。

3.AR1能拼通AR2

三.实验步骤。

                  LSW1

system-view    //开启窗口视图

[Huawei]vlan 10          //创建vlan10

[Huawei-vlan10]vlan 20

[Huawei-vlan20]int e0/0/1

[Huawei-Ethernet0/0/1]port link-type access   //把接口模式改成access模式

[Huawei-Ethernet0/0/1]port default vlan 10   //在接口上加vlan成员

[Huawei]int Eth-Trunk 1      //创建以太网组1

[Huawei-Eth-Trunk1]int e0/0/17    //进接口

[Huawei-Ethernet0/0/17]eth-trunk 1    //添加到以太网组1

[Huawei-Ethernet0/0/17]int e0/0/18

[Huawei-Ethernet0/0/18]eth-trunk 1

[Huawei]int Eth-Trunk 2

[Huawei-Eth-Trunk2]int e0/0/21

[Huawei-Ethernet0/0/21]eth-trunk 2

[Huawei-Ethernet0/0/21]int e0/0/22

[Huawei-Ethernet0/0/22]eth-trunk 2

[Huawei-Ethernet0/0/18]qu

[Huawei]int Eth-Trunk 1     //进入以太网1

[Huawei-Eth-Trunk1]port link-type trunk   //把模式改为trunk

[Huawei-Eth-Trunk1]port trunk allow-pass vlan all  //允许所有的vlan

[Huawei]int Eth-Trunk 2

[Huawei-Eth-Trunk2]port link-type trunk

[Huawei-Eth-Trunk2]port trunk allow-pass vlan all

                  LSW2

system-view

[Huawei]vlan 10

[Huawei-vlan10]vlan 20

[Huawei-vlan20]int e0/0/2

[Huawei-Ethernet0/0/2]port link-type access

[Huawei-Ethernet0/0/2]port default vlan 20

[Huawei]quit

[Huawei]int Eth-Trunk 1

[Huawei-Eth-Trunk1]int e0/0/17

[Huawei-Ethernet0/0/17]eth-trunk 1

[Huawei-Ethernet0/0/17]int e0/0/18

[Huawei-Ethernet0/0/18]eth-trunk 1

[Huawei-Ethernet0/0/18]qu

[Huawei]int Eth-Trunk 1

[Huawei-Eth-Trunk1]port link-type trunk

[Huawei-Eth-Trunk1]port trunk allow-passvlan all

                  AR1

system-view

[Huawei]int Eth-Trunk 2

[Huawei-Eth-Trunk2]undo portswitch

[Huawei]int g0/0/0

[Huawei-GigabitEthernet0/0/0]eth-trunk 2

[Huawei-GigabitEthernet0/0/0]int g0/0/1

[Huawei-GigabitEthernet0/0/1]eth-trunk 2

[Huawei]int Eth-Trunk2       //进入以太网组2

[Huawei-Eth-Trunk2]undo shutdown   //开启接口

[Huawei-Eth-Trunk2]int eth-trunk 2.10  //进子接口

[Huawei-Eth-Trunk2.10]dot1q termination vid 10   //封装子接口vlan10

[Huawei-Eth-Trunk2.10]arp broadcast enable

[Huawei-Eth-Trunk2.10]ip add 192.168.10.1 24   //vlan10的网关

[Huawei-Eth-Trunk2.10]int eth-trunk 2.20

[Huawei-Eth-Trunk2.20]dot1q termination vid 20

[Huawei-Eth-Trunk2.20]arp broadcast enable

[Huawei-Eth-Trunk2.20]ip add 192.168.20.1 24

[Huawei-Eth-Trunk2.20]un shut

[Huawei]int Eth-Trunk3

[Huawei-Eth-Trunk3]undo portswitch    //把一个接口变成三层口

[Huawei-GigabitEthernet1/0/0]eth-trunk 3

[Huawei-GigabitEthernet1/0/0]int g2/0/0

[Huawei-GigabitEthernet2/0/0]eth-trunk 3

[Huawei-GigabitEthernet2/0/0]int eth-trunk 3

[Huawei-Eth-Trunk3]ip add 202.106.1.10 24    //ip地址

[Huawei-Eth-Trunk3]un shut


AR2

sy

[Huawei-Eth-Trunk3]undo portswitch

[Huawei-GigabitEthernet0/0/0]eth-trunk 3

[Huawei-GigabitEthernet0/0/0]int g0/0/1

[Huawei-GigabitEthernet0/0/1]eth-trunk 3

[Huawei-GigabitEthernet0/0/1]int eth-trunk 3

[Huawei-Eth-Trunk3]ip add 202.106.1.20 24

[Huawei-Eth-Trunk3]un shut

四.

华为做链路捆绑_第2张图片

证明三层和三层互绑没有问题。

华为做链路捆绑_第3张图片

华为做链路捆绑_第4张图片


证明用链路捆绑做的单臂路由。