EMC VMAX10k 前端端口详解和磁盘划分过程
EMC VMAX10k 前端端口详解和磁盘划分过程
转载请注明： http://blog.itpub.net/blog/post/draftid/43153/
本文针对EMC POOL池已经划好，操作过和为VP种thin设备划分过程
一、初识前端端口
FA端口详解：
针对本公司VMAX 10K存储。
每个机柜有两个ENGINE，BAY1后面重右到左为dir1，和dir2, BAY2后面重右到左为dir3，和dir4
每个DIR中SLOT3,SLOT4中有8个FA端口，从左下角开始E0,E1,F0,F1,G0,G1,H0,H1
下载更出了所有的的前端 port端口，FA-1E：FA代表前端端口，1E：0代表1E Director上的0口
[root@ABM-APP1 bin]# ./symcfg list -fa all -sid 404
Symmetrix ID: 000298700404 (Local)
S Y M M E T R I X F I B R E D I R E C T O R S
Dir Port WWN Flags Max
AVPFG Speed
FA-1E 0 50000975F0065100 X.X.. 8
FA-1E 1 50000975F0065101 X.X.. 8
FA-2E 0 50000975F0065104 X.X.. 8
FA-2E 1 50000975F0065105 X.X.. 8
FA-3E 0 50000975F0065108 X.X.. 8
FA-3E 1 50000975F0065109 X.X.. 8
FA-4E 0 50000975F006510C X.X.. 8
FA-4E 1 50000975F006510D X.X.. 8
FA-1F 0 50000975F0065140 X.X.. 8
FA-1F 1 50000975F0065141 X.X.. 8
FA-2F 0 50000975F0065144 X.X.. 8
FA-2F 1 50000975F0065145 X.X.. 8
FA-3F 0 50000975F0065148 X.X.. 8
FA-3F 1 50000975F0065149 X.X.. 8
FA-4F 0 50000975F006514C X.X.. 8
FA-4F 1 50000975F006514D X.X.. 8
FA-1G 0 50000975F0065180 X.X.. 8
FA-1G 1 50000975F0065181 X.X.. 8
FA-2G 0 50000975F0065184 X.X.. 8
FA-2G 1 50000975F0065185 X.X.. 8
FA-3G 0 50000975F0065188 X.X.. 8
FA-3G 1 50000975F0065189 X.X.. 8
FA-4G 0 50000975F006518C X.X.. 8
FA-4G 1 50000975F006518D X.X.. 8
FA-1H 0 50000975F00651C0 X.X.. 8
FA-1H 1 50000975F00651C1 X.X.. 8
FA-2H 0 50000975F00651C4 X.X.. 8
FA-2H 1 50000975F00651C5 X.X.. 8
FA-3H 0 50000975F00651C8 X.X.. 8
FA-3H 1 50000975F00651C9 X.X.. 8
FA-4H 0 50000975F00651CC X.X.. 8
FA-4H 1 50000975F00651CD X.X.. 8
二、配置举例
本次计划使用第三个engine的F1口和第四个engine的F1口，即3f:1,4f:1
1. 光纤交换机zone划分
（1）./symcfg list -fa all -sid 404找出所需要使用的3f:1,4f:1 wwn号
./symcfg list -fa all -sid 404
……
FA-3F 1 50000975F0065149 X.X.. 8
……
FA-4F 1 50000975F006514D X.X.. 8
（2）在AIX系统中使用lscfg –vpl fcsx找出HBA卡的wwn号
10000000C9737DC2
10000000C9894DBD
（3）登录上CISCO光纤交换机
show flogi database 找到上述FA口和hba卡的对应端口
MDS-1(config-if)# show flogi database
--------------------------------------------------------------------------------
INTERFACE VSAN FCID PORT NAME NODE NAME
--------------------------------------------------------------------------------
fc1/1 1 0x030100 50:00:09:75:f0:06:51:00 50:00:09:75:f0:06:50:00
fc1/2 1 0x030200 50:00:09:75:f0:06:51:01 50:00:09:75:f0:06:50:00
fc1/3 1 0x030300 50:00:09:75:f0:06:51:40 50:00:09:75:f0:06:50:00
fc1/4 1 0x030400 50:00:09:75:f0:06:51:41 50:00:09:75:f0:06:50:00
fc1/5 1 0x030600 50:00:09:75:f0:06:51:80 50:00:09:75:f0:06:50:00
fc1/6 1 0x030500 50:00:09:75:f0:06:51:81 50:00:09:75:f0:06:50:00
fc1/7 1 0x030700 50:00:09:75:f0:06:51:c0 50:00:09:75:f0:06:50:00
fc1/8 1 0x030900 50:00:09:75:f0:06:51:c1 50:00:09:75:f0:06:50:00
fc1/9 1 0x030800 50:00:09:75:f0:06:51:08 50:00:09:75:f0:06:50:00
fc1/10 1 0x030a00 50:00:09:75:f0:06:51:09 50:00:09:75:f0:06:50:00
fc1/11 1 0x030c00 50:00:09:75:f0:06:51:48 50:00:09:75:f0:06:50:00
fc1/12 1 0x030b00 50:00:09:75:f0:06:51:49 50:00:09:75:f0:06:50:00
fc1/13 1 0x030d00 50:00:09:75:f0:06:51:88 50:00:09:75:f0:06:50:00
fc1/14 1 0x030e00 50:00:09:75:f0:06:51:89 50:00:09:75:f0:06:50:00
fc1/15 1 0x030f00 50:00:09:75:f0:06:51:c8 50:00:09:75:f0:06:50:00
fc1/16 1 0x031000 50:00:09:75:f0:06:51:c9 50:00:09:75:f0:06:50:00
fc1/17 1 0x031100 50:01:43:80:28:ce:c5:ac 50:01:43:80:28:ce:c5:ad
fc1/18 1 0x031200 50:01:43:80:28:ce:c5:ae 50:01:43:80:28:ce:c5:af
fc1/19 1 0x031300 50:01:43:80:28:ce:c5:dc 50:01:43:80:28:ce:c5:dd
fc1/20 1 0x031400 50:01:43:80:28:ce:c5:de 50:01:43:80:28:ce:c5:df
fc1/21 1 0x031500 10:00:00:00:c9:89:4d:bd 20:00:00:00:c9:89:4d:bd
第二台交换机略
由上我们可以知道光纤交换机的fc1/12,fc1/21为我们要配置的zone口
配置ZONE
MDS-1(config)# zone name zone_migtest_hba1 vsan 1 #新建ZONE
MDS-1(config-zone)# member interface fc 1/12
MDS-1(config-zone)# member interface fc 1/21 #将fc1/12,fc1/21口划入zone里
MDS-1(config)# zoneset name zoneset_HP-DL980G7_Server vsan 1 #进行zoneset
MDS-1(config-zoneset)# member zone_migtest_hba1 #将新建zone member入zoneset里
MDS-1(config)# zoneset activate name zoneset_HP-DL980G7_Server vsan 1 #激活zoneseg
MDS-1# copy running-config startup-config #将修改配置存入启动配置里
小知识：当我查看ZONE和ZONESET的时候，如果FCID前有“*”号，说明链路已经连接
MDS-1# show zone active
zone name zone_HP-DL980G7_1 vsan 1
* fcid 0x031100 [interface fc1/17 swwn 20:00:00:2a:6a:36:1d:d0]
* fcid 0x030300 [interface fc1/3 swwn 20:00:00:2a:6a:36:1d:d0]
……
zone name zone_migtest_hba1 vsan 1
* fcid 0x030c00 [interface fc1/11 swwn 20:00:00:2a:6a:36:1d:d0]
* fcid 0x031500 [interface fc1/21 swwn 20:00:00:2a:6a:36:1d:d0]
第二台光纤交换机配置同上，此处略
2. AIX主机cfgmgr –v
如果我们此时在AIX主机中执行cfgmgr –v,可以发现已经识别到了一块EMC存储的盘，此盘是主机和EMC存储的访问控制盘，说明主机和存储链路已经通
3. Enable solution划分存储组
整个过程：创建TDEVàbind tdev到poolà建initiator组à建port组à建storage组à建masking view六步
（1）划分前准备工作
./symdev -sid 404 list更出所有设备
./symcfg -sid 404 list –pool
./symaccess -sid 404 list
./symaccess -sid 404 list view
……
（2）创建过程
./symconfigure -sid 404 -cmd "create dev count=1,size=500 GB,emulation=FBA,config=TDEV,meta_member_size=125 GB;" preview
./symconfigure -sid 404 -cmd "create dev count=1,size=500 GB,emulation=FBA,config=TDEV,meta_member_size=125 GB;" commit
./symconfigure -sid 404 -cmd "bind tdev 0357:035A to pool VP_FC600_MIR,preallocate size=All;" preview
./symconfigure -sid 404 -cmd "bind tdev 325:356 to pool VP_FC600_MIR,preallocate size=All;" commit
./symaccess -sid 404 create -name migtest_ig -type initiator -wwn "10000000C9894DBD"
./symaccess -sid 404 add -name migtest_ig -type initiator -wwn "10000000C9737DC2"
./symaccess -sid 404 create -name migtest_pg -type port -dirport "3f:1,4f:1"
./symaccess -sid 404 create -name migtest_sg -type storage -devs "357"
./symaccess -sid 404 create view -name migtest_view -sg migtest_sg -ig migtest_ig -pg migtest_pg
4. 安装EMC AIX ODM库
（1）下载
来自 “ ITPUB博客 ” ，链接：http://blog.itpub.net/645199/viewspace-1385617/，如需转载，请注明出处，否则将追究法律责任。
转载于:http://blog.itpub.net/645199/viewspace-1385617/