1.必须向CST_COMP_SNAP_INTERFACE表中插入此工单所有工序的数据（也就是说同样的工单插入多条，只是工序号不一样）
标准文档：
Note: If there are multiple operation sequences then,
Insert multiple records in CST_COMP_SNAP_INTERFACE, one record for each
OPERATION_SEQ_NUM in WIP_OPERATIONS for the appropriate WIP_ENTITY_ID (with the
same transaction_interface_id).
否则会出现问题：
（1）工单通过mtl_transactions_interface接口表，完工入库了，但是没有扣减最后一站移动站(to move站)数量
“接口表提交后，没有错误信息，数据成功提交了；； 查询物料交易事务处理表，此工单已有完工入库记录（库存也有增加），但就是没有扣减最后一站移动站(to move站)数量（同时工单已完工量也没有相应增加）。 CST_COMP_SNAP_INTERFACE 表中的数据一点都不动（成本管理器正常）”
（2）报错：
2.完工入库之前先移动工单至最后一道工序的move状态
3.完工退回之前先移动工单至第一道工序的排队状态
报错信息：
解决：
metalink上的一些解决办法
Wip Assembly Completion For A Job Through MTL_TRANSACTIONS_INTERFACE Is Not Updating Job Completed Quantity [ID 745112.1]
修改时间 11-SEP-2010 类型 PROBLEM 状态 MODERATED
In this Document
Symptoms
Cause
Solution
References
Platforms: 1-914CU;
This document is being delivered to you via Oracle Support's Rapid Visibility (RaV) process and therefore has not been subject to an independent technical review.
Applies to:
Oracle Work in Process - Version: 11.5.9 to 12.0.4 - Release: 11.5 to 12
Information in this document applies to any platform.
Checked for relevance 11-SEP-2010
Symptoms
On 12.0.4 in Production:
Find that when WIP Assembly Completion transaction is performed for a Discrete job through
mtl_transaction_interface, the transaction is getting processed successfully but the completed
quantity is not getting updated in the Discrete job also quantity still remaining in To Move of
last operation.
EXPECTED BEHAVIOR
Expect that the quantity should get updated in the discrete jobs.
STEPS
The issue can be reproduced at will with the following steps:
1. Create a discrete job, release it
2. Perform Move transaction to the last operation to move step.
3. Perform WIP Assembly Completion through the MTI, it gets processed successfully
4. Verify the job header infoformation, still the quantity is not completed.
BUSINESS IMPACT
The issue has the following business impact:
Due to this issue, there is lot of discrepancy in the job.
.
Cause
The cause of the issue is invalid / incorrect data in cst_comp_snap_interface table.
The cause for this invalid data has been determined as the data in cst_comp_snap_interface corresponding
to completion record in MTI (linked with transaction_interface_id) was not populated with the correct op_seq_num.
This has explained in the following bug.
Bug 5746008 'CSTPACMS:VALIDATE_SNAP_INTERFACE 30' ERROR IN TRANSACTION OPEN INTERFACE
Customer was incorrectly populating the interface data.
cst_comp_snap_interface corresponding to completion record in MTI (linked with
transaction_interface_id) was not populated with the op_seq_num.
In the current scenario, user populated the op_seq_num but it is wrong value.
For any reference related to WIP Assembly Completion through MTI, can refer Note 458801.1
Solution
To implement the solution, please execute the following steps:
1. Insert the correct operation sequence number in to cst_comp_snap_interface table which corresponds
to the operation sequence of that particular job.
Note: If there are multiple operation sequences then,
Insert multiple records in CST_COMP_SNAP_INTERFACE, one record for each
OPERATION_SEQ_NUM in WIP_OPERATIONS for the appropriate WIP_ENTITY_ID (with the
same transaction_interface_id).
2. Retest the issue.
References
NOTE:458801.1 - Standard API/Interface Needed to Perform Work Order Completion: WIP Assembly Completion Transaction For Discrete Jobs Can Be Performed Through Mtl_Transactions_Interface Table
SR 7174967.993
显示相关信息 相关的
产品
* Oracle E-Business Suite > Manufacturing > Discrete Manufacturing > Oracle Work in Process
关键字
CST_COMP_SNAP_INTERFACE; DISCRETE JOB; OPEN INTERFACES; COMPLETION TRANSACTIONS
错误
30 ERROR